The bits used to set the PCI bus speed on AR9 are slightly different to
those used on Danube.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2614/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq base offset needs to be ignored when matching irqs to external
interrupt pins. Taking the offset into account resulted in the EIU not
being brought up properly.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2616/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only some GCC versions such as gcc 4.2 notice that the variable wr in
build_r3000_tlb_modify_handler is used uninitialized. When using one
of those GCCs the build will fail due to -Werror. GCC 4.6 does not
warn about the uninitialized use of wr.
This issue was introduced by 7211f4d7a3dcbe57c5d396c334dca525315dceb2
[MIPS: Close races in TLB modify handlers.]
Reported-by: Ganesan Ramalingam <ganesan18@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code forgets the Au1100 when looking for the correct method to
suspend the chip.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Harmless typo which prints an error message although MAC0 was registered
successfully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/pmc-sierra/msp71xx/msp_irq.o
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:112:2: error: request for member ‘flags’ in something not a structure or union
/home/ralf/src/linux/linux-mips/arch/mips/pmc-sierra/msp71xx/msp_irq.c:118:2: error: request for member ‘flags’ in something not a structure or union
make[4]: *** [arch/mips/pmc-sierra/msp71xx/msp_irq.o] Error 1
caused by 57336bc1056798d89714b7fb1b1d197e6bda6819 [MIPS: Mark cascade and
low level interrupts IRQF_NO_THREAD].
Commas to separate struct initializers generally are considered useful to
enhance the compilation experience of the user.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
do_signal() does __put_user() which can fault, resulting in a might_sleep()
warning in down_read(&mm->mmap_sem) and a "scheduling while atomic" warning
when mmap_sem is contented. On Swarm this also results in:
WARNING: at kernel/smp.c:459 smp_call_function_many+0x148/0x398()
Modules linked in:
Call Trace:
[<ffffffff804b48a4>] dump_stack+0x1c/0x50
[<ffffffff8013dc94>] warn_slowpath_common+0x8c/0xc8
[<ffffffff8013dcfc>] warn_slowpath_null+0x2c/0x40
[<ffffffff801864a0>] smp_call_function_many+0x148/0x398
[<ffffffff80186748>] smp_call_function+0x58/0xa8
[<ffffffff80119b5c>] r4k_flush_data_cache_page+0x54/0xd8
[<ffffffff801f39bc>] handle_pte_fault+0xa9c/0xad0
[<ffffffff801f40d0>] handle_mm_fault+0x158/0x200
[<ffffffff80115548>] do_page_fault+0x218/0x3b0
[<ffffffff80102744>] ret_from_exception+0x0/0x10
[<ffffffff8010eb18>] copy_siginfo_to_user32+0x50/0x298
[<ffffffff8010edf0>] setup_rt_frame_32+0x90/0x250
[<ffffffff80106414>] do_notify_resume+0x154/0x358
[<ffffffff80102930>] work_notifysig+0xc/0x14
Fixed by enabling interrupts in do_notify_resume before delivering signals.
[ralf@linux-mips.org: Reported and original fix by tglx but I wanted to
minimize the amount of code being run with interrupts disabled so I moved
the local_irq_disable() call right into do_notify_resume. Which is saner
than doing it in entry.S.]
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All low level interrupts have been marked NO_THREAD, so MIPS can enjoy
the wonderful world of forced threaded interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are two cascade interrupts in Loongson machines, one for bonito
northbridge, another for the 8259A controller in the southbridge. Both
want to be non threaded.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/2638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mark interrupts with no_action handler, cascade interrupts, low level
interrupts (bus error, halt ..) with IRQF_NO_THREAD to exclude them
from forced threading.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On preempt-rt this lock needs to be raw, so it does not get converted
to a sleeping spinlock. Trying to sleep in a panic is not really
desireable.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/kernel/ftrace.c: In function ‘ftrace_get_parent_ra_addr’:
arch/mips/kernel/ftrace.c:212: error: implicit declaration of function ‘in_kernel_space’
arch/mips/kernel/ftrace.c: In function ‘prepare_ftrace_return’:
arch/mips/kernel/ftrace.c:314: error: ‘MCOUNT_OFFSET_INSNS’ undeclared (first use in this function)
arch/mips/kernel/ftrace.c:314: error: (Each undeclared identifier is reported only once
arch/mips/kernel/ftrace.c:314: error: for each function it appears in.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2634/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
This problem is included in the following commit.
commit 28f65c11f2
Author: Joe Perches <joe@perches.com>
Date: Thu Jun 9 09:13:32 2011 -0700
treewide: Convert uses of struct resource to resource_size(ptr)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: Joe Perches <joe@perches.com>
Patchwork: https://patchwork.linux-mips.org/patch/2654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in arch/mips/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
To: LKML <linux-kernel@vger.kernel.org>
Cc: trivial@kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2540/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The comment for the slave PIC is changed from 8259A-1 to 8259A-2.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
To: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2693/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we could find tc on the tc list for @index, the found tc should be returned.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
To: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2692/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Synopsys DesignWare UART in pmc-sierra msp71xx has an extra feature
where the UART detects a write attempt to the LCR whilst busy and raises
an interrupt. The driver needs to clear the interrupt and rewrite the
LCR. Move this into platform code and out of the 8250 driver.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of the "soc-audio" platform device is no longer en vogue,
update the code to the newer, simpler way of doing things.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PSC audio drivers (psc-ac97/psc-i2s) register the DMA platform_device
on their own. This is frowned upon, from now on board code must
register a simple pcm dma platform device for each PSC with sound duties.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver suitable for the AC97 part on the DB1000/DB1500/DB1100
boards.
Run-tested on DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Page table entries are made invalid by writing a zero into the the PTE
slot in a page table. This creates a race condition with the TLB
modify handlers when they are updating the PTE.
CPU0 CPU1
Test for _PAGE_PRESENT
. set to not _PAGE_PRESENT (zero)
Set to _PAGE_VALID
So now the page not present value (zero) is suddenly valid and user
space programs have access to physical page zero.
We close the race by putting the test for _PAGE_PRESENT and setting of
_PAGE_VALID into an atomic LL/SC section. This requires more registers
than just K0 and K1 in the handlers, so we need to save some registers
to a save area and then restore them when we are done.
The save area is an array of cacheline aligned structures that should
not suffer cache line bouncing as they are CPU private.
[ralf@linux-mips.org: Fix !defined(CONFIG_MIPS_PGD_C0_CONTEXT) build error.]
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2577/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This can be used from either 32-bit or 64-bit code to generate logical
right shifts of any constant amount.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Enable cpu_has_clo_clz only when CONFIG_CPU_MIPS32 or CONFIG_CPU_MIPS64
is selected. This will optimize fls() and __fls() to use CLZ insn, and
eventually ffs() and __ffs() as well.
Malta and MIPSSim are development platforms, and need to take care of
various processor configurations, release rivisions and so on, even
across different MIPS ISAs. For such platforms we have to be careful,
for instance, with turning on cpu_has_mips{32,64}r[12] features.
As for CLZ, all MIPS32/64 processors support it, regardless of release
revisions.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
To: David VomLehn <dvomlehn@cisco.com>
To: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1453/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This will optimize fls() and __fls() to use CLZ throughout the kernel,
and any other optimizations that depend on constant cpu_has_* values
will also be used.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
To: David VomLehn <dvomlehn@cisco.com>
To: macro@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1452/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
fixrange_init() allocates page tables for all addresses higher than
FIXADDR_TOP. On processors that override the default FIXADDR_TOP
address of 0xfffe_0000, this can consume up to 4 pages (1 page per 4MB)
for pgd's that are never used.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1980/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Memory maps and addressing quirks are normally defined in <spaces.h>.
There are already three targets that need to override FIXADDR_TOP, and
others exist. This will be a cleaner approach than adding lots of
ifdefs in fixmap.h .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1573/
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On processors with deep write buffers, it is likely that many cycles
will pass between a CACHE instruction and the time the data actually
gets written out to DRAM. Add a SYNC instruction to ensure that the
buffers get emptied before the flush functions return.
Actual problem seen in the wild:
1) dma_alloc_coherent() allocates cached memory
2) memset() is called to clear the new pages
3) dma_cache_wback_inv() is called to flush the zero data out to memory
4) dma_alloc_coherent() returns an uncached (kseg1) pointer to the
freshly allocated pages
5) Caller writes data through the kseg1 pointer
6) Buffered writeback data finally gets flushed out to DRAM
7) Part of caller's data is inexplicably zeroed out
This patch adds SYNC between steps 3 and 4, which fixed the problem.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pfn_valid() compares the PFN to max_mapnr:
__pfn >= min_low_pfn && __pfn < max_mapnr;
On HIGHMEM kernels, highend_pfn is used to set the value of max_mapnr.
Unfortunately, highend_pfn is left at zero if the system does not
actually have enough RAM to reach into the HIGHMEM range. This causes
pfn_valid() to always return false, and when debug checks are enabled
the kernel will fail catastrophically:
Memory: 22432k/32768k available (2249k kernel code, 10336k reserved, 653k data, 1352k init, 0k highmem)
NR_IRQS:128
kfree_debugcheck: out of range ptr 81c02900h.
Kernel bug detected[#1]:
Cpu 0
$ 0 : 00000000 10008400 00000034 00000000
$ 4 : 8003e160 802a0000 8003e160 00000000
$ 8 : 00000000 0000003e 00000747 00000747
...
On such a configuration, max_low_pfn should be used to set max_mapnr.
This was seen on 2.6.34.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
To: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1992/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduced topdown mmap support in user process address
space allocation policy.
Recently, we ran some large applications that use mmap heavily and
lead to OOM due to inflexible mmap allocation policy on MIPS32.
Since most other major archs supported it for years, it is reasonable
to follow the trend and reduce the pain of porting applications.
Due to cache aliasing concern, arch_get_unmapped_area_topdown() and
other helper functions are implemented in arch/mips/kernel/syscall.c.
Signed-off-by: Jian Peng <jipeng2005@gmail.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2389/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The address limit is already set in flush_old_exec() via set_fs(USER_DS)
so this assignment is redundant.
[ralf@linux-mips.org: also see dac853ae89 for
further explanation.]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2466/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.
Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.
Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.
The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.
This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.
Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'timers-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mips: Fix i8253 clockevent fallout
i8253: Cleanup outb/inb magic
arm: Footbridge: Use common i8253 clockevent
mips: Use common i8253 clockevent
x86: Use common i8253 clockevent
i8253: Create common clockevent implementation
i8253: Export i8253_lock unconditionally
pcpskr: MIPS: Make config dependencies finer grained
pcspkr: Cleanup Kconfig dependencies
i8253: Move remaining content and delete asm/i8253.h
i8253: Consolidate definitions of PIT_LATCH
x86: i8253: Consolidate definitions of global_clock_event
i8253: Alpha, PowerPC: Remove unused asm/8253pit.h
alpha: i8253: Cleanup remaining users of i8253pit.h
i8253: Remove I8253_LOCK config
i8253: Make pcsp sound driver use the shared i8253_lock
i8253: Make pcspkr input driver use the shared i8253_lock
i8253: Consolidate all kernel definitions of i8253_lock
i8253: Unify all kernel declarations of i8253_lock
i8253: Create linux/i8253.h and use it in all 8253 related files
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (123 commits)
perf: Remove the nmi parameter from the oprofile_perf backend
x86, perf: Make copy_from_user_nmi() a library function
perf: Remove perf_event_attr::type check
x86, perf: P4 PMU - Fix typos in comments and style cleanup
perf tools: Make test use the preset debugfs path
perf tools: Add automated tests for events parsing
perf tools: De-opt the parse_events function
perf script: Fix display of IP address for non-callchain path
perf tools: Fix endian conversion reading event attr from file header
perf tools: Add missing 'node' alias to the hw_cache[] array
perf probe: Support adding probes on offline kernel modules
perf probe: Add probed module in front of function
perf probe: Introduce debuginfo to encapsulate dwarf information
perf-probe: Move dwarf library routines to dwarf-aux.{c, h}
perf probe: Remove redundant dwarf functions
perf probe: Move strtailcmp to string.c
perf probe: Rename DIE_FIND_CB_FOUND to DIE_FIND_CB_END
tracing/kprobe: Update symbol reference when loading module
tracing/kprobes: Support module init function probing
kprobes: Return -ENOENT if probe point doesn't exist
...
pit_clockevent wants to replaced in the argument of the callback
function as well.
Reported-by; Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix few issues in the Netlogic code:
- Use handle_percpu_irq to handle per-cpu interrupts
- Remove unused function nlm_common_ipi_handler()
- Call scheduler_ipi() on SMP_RESCHEDULE_YOURSELF
- Enable interrupts in nlm_smp_finish()
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d6d5d5c4a (MIPS: Sibyte: Convert to new irq_chip functions)
removed the mask function which breaks irq_shutdown(). Restore it.
Reported-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 6be63bbbda (lmo) rsp.
af3a1f6f48 (kernel.org) the Malta code does
no longer probe for presence of GCMP if CMP is not configured. This means
that the variable gcmp_present well be left at its default value of -1
which normally is meant to indicate that GCMP has not yet been mmapped.
This non-zero value is now interpreted as GCMP being present resulting
in a write attempt to a GCMP register resulting in a crash.
Reported and a build fix on top of my fix by Rob Landley <rob@landley.net>.
Reported-by: Rob Landley <rob@landley.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2413/
Renumbering was necessary because I had already wired up setns(2) in the
linux-mips.org tree in commit c3fce54644cabbb90700cc3acc040718a377f609
[MIPS: Wire up new sendmmsg syscall.] but the same syscall numbers were
used by 7b21fddd08 [ns: Wire up the setns
system call] resulting in a conflict.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit ee6114202e48dc282c6d04741e9c5d7171eb8bb8 (lmo) rsp.
1685f3b158 (kernel.org) ["MIPS: SMTC: Move
declaration of smtc_init_secondary to <asm/smtc.h>."] didn't quite do
that - it rather lost the declaration of smtc_init_secondary resulting in
a build error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Make sure that the 'static' keywork is at the beginning of declaration
for arch/mips/include/asm/mach-jz4740/gpio.h
This gets rid of warnings like
warning: ‘static’ is not at beginning of declaration
when building with -Wold-style-declaration (and/or -Wextra which also
enables it).
Also a few tiny whitespace changes.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a NODE level to the generic cache events which is used to measure
local vs remote memory accesses. Like all other cache events, an
ACCESS is HIT+MISS, if there is no way to distinguish between reads
and writes do reads only etc..
The below needs filling out for !x86 (which I filled out with
unsupported events).
I'm fairly sure ARM can leave it like that since it doesn't strike me as
an architecture that even has NUMA support. SH might have something since
it does appear to have some NUMA bits.
Sparc64, PowerPC and MIPS certainly want a good look there since they
clearly are NUMA capable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1303508226.4865.8.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stack unwinding is done by code examination. For kernelspace, the
already existing unwind function is utilized that uses kallsyms to
quickly find the beginning of functions. For userspace a new function
was added that examines code at and before the pc.
Signed-off-by: Daniel Kalmar <kalmard@homejinni.com>
Signed-off-by: Gergely Kis <gergely@homejinni.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
The unwind_stack_by_address variant supports unwinding based
on any kernel code address.
This symbol is also exported so it can be called from modules.
Signed-off-by: Daniel Kalmar <kalmard@homejinni.com>
Signed-off-by: Gergely Kis <gergely@homejinni.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only the Siemens-Nixdorf RM series workstations and the Jazz family
workstations have PC speakers built in; Malta can connect one via the
infamous AMR connector with an AMR sound card or a little creativity.
So we don't want to offer the PC speaker driver on all MIPS systems.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180611.061710714@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Lenghty lists of the kind "depends on ARCH1 || ARCH2 ... || ARCH123" are
usually either wrong or too coarse grained. Or plain an ugly sin.
[ tglx: Fixed up amigaone ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Gerhard Pircher <gerhard_pircher@gmx.net>
Link: http://lkml.kernel.org/r/20110601180610.984881988@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as PIT_TICK_RATE.
MIPS defines PIT_LATCH as LATCH which in <linux/timex.h> is defined as
((CLOCK_TICK_RATE + HZ/2) / HZ) and <asm/timex.h> again defines
CLOCK_TICK_RATE as 1193182.
ARM defines PITCH_LATCH as ((PIT_TICK_RATE + HZ / 2) / HZ) - and that's
the sanest thing and equivalent to above definitions so use that as the
new definition in <linux/i8253.h>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/20110601180610.832810002@duck.linux-mips.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move them to drivers/clocksource/i8253.c and remove the
implementations in arch/
[ tglx: Avoid the extra file in lib - folded arch patches in. The
export will become conditional in a later step ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/20110601180610.221426078@duck.linux-mips.net
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Fix PM QOS's user mode interface to work with ASCII input
PM / Hibernate: Update kerneldoc comments in hibernate.c
PM / Hibernate: Remove arch_prepare_suspend()
PM / Hibernate: Update some comments in core hibernate code
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most arches define CONFIG_DEBUG_STACK_USAGE exactly the same way. Move it
to lib/Kconfig.debug so each arch doesn't have to define it. This
obviously makes the option generic, but that's fine because the config is
already used in generic code.
It's not obvious to me that sysrq-P actually does anything caution by
keeping the most inclusive wording.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fold all the mmu_gather rework patches into one for submission
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All architectures supporting hibernation define
arch_prepare_suspend() as an empty function, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
A new utility function (core_kernel_data()) is used to determine if a
passed in address is part of core kernel data or not. It may or may not
return true for RO data, but this utility must work for RW data.
Thus both _sdata and _edata must be defined and continuous,
without .init sections that may later be freed and replaced by
volatile memory (memory that can be freed).
This utility function is used to determine if data is safe from
ever being freed. Thus it should return true for all RW global
data that is not in a module or has been allocated, or false
otherwise.
Also change core_kernel_data() back to the more precise _sdata condition
and document the function.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: JamesE.J.Bottomley <jejb@parisc-linux.org>
Link: http://lkml.kernel.org/r/1305855298.1465.19.camel@gandalf.stny.rr.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
----
arch/alpha/kernel/vmlinux.lds.S | 1 +
arch/m32r/kernel/vmlinux.lds.S | 1 +
arch/m68k/kernel/vmlinux-std.lds | 2 ++
arch/m68k/kernel/vmlinux-sun3.lds | 1 +
arch/mips/kernel/vmlinux.lds.S | 1 +
arch/parisc/kernel/vmlinux.lds.S | 3 +++
kernel/extable.c | 12 +++++++++++-
7 files changed, 20 insertions(+), 1 deletion(-)
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (107 commits)
perf stat: Add more cache-miss percentage printouts
perf stat: Add -d -d and -d -d -d options to show more CPU events
ftrace/kbuild: Add recordmcount files to force full build
ftrace: Add self-tests for multiple function trace users
ftrace: Modify ftrace_set_filter/notrace to take ops
ftrace: Allow dynamically allocated function tracers
ftrace: Implement separate user function filtering
ftrace: Free hash with call_rcu_sched()
ftrace: Have global_ops store the functions that are to be traced
ftrace: Add ops parameter to ftrace_startup/shutdown functions
ftrace: Add enabled_functions file
ftrace: Use counters to enable functions to trace
ftrace: Separate hash allocation and assignment
ftrace: Create a global_ops to hold the filter and notrace hashes
ftrace: Use hash instead for FTRACE_FL_FILTER
ftrace: Replace FTRACE_FL_NOTRACE flag with a hash of ignored functions
perf bench, x86: Add alternatives-asm.h wrapper
x86, 64-bit: Fix copy_[to/from]_user() checks for the userspace address limit
x86, mem: memset_64.S: Optimize memset by enhanced REP MOVSB/STOSB
x86, mem: memmove_64.S: Optimize memmove by enhanced REP MOVSB/STOSB
...
We only use the three low-order mailbox bits. Leave the upper bits alone
for possible use by drivers and other software.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2090/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon uses different interrupt irq for timer and performance counters.
Set CvmCtl[IPPCI] to correct irq value very early.
Signed-off-by: Chandrakala Chavva <cchavva@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/2085/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Assume that the boot loader knows the physical memory of the system and
deduce that information from the contents of the SDRAM control register.
It is still possible to override with with the "mem=" parameter, but we
have a sensible default now.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2319/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634u are using minuses between the blocks
of the MAC address and other devices are using colons to separate them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2366/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some embedded devices like the Netgear WNDR3300 have two SSB based cards
without an own sprom on the pci bus. We have to provide two different
fallback sproms for these and this was not possible with the old solution.
In the bcm47xx architecture the sprom data is stored in the nvram in the
main flash storage. The architecture code will be able to fill the sprom
with the stored data based on the bus where the device was found.
The bcm63xx code should do the same thing as before, just using the new
API.
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses. This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
replace au_readl/au_writel with __raw_readl/__raw_writel,
and clean up IC-related stuff from the headers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes a build failure with gpio_keys and CONFIG_GPIOLIB=n (mtx1):
CC drivers/input/keyboard/gpio_keys.o
gpio_keys.c: In function 'gpio_keys_report_event':
gpio_keys.c:325:2: error: implicit declaration of function 'gpio_get_value_cansleep'
gpio_keys.c: In function 'gpio_keys_setup_key':
gpio_keys.c:390:3: error: implicit declaration of function 'gpio_set_debounce'
Also add stubs for the other new functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2346/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting Config[OD] gets rid of a _LOT_ of spurious CPLD interrupts,
but also decreases overall performance a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the driver for the ETOP Packet Processing Engine (PPE32)
found inside the XWAY family of Lantiq MIPS SoCs. This driver makes 100MBit
ethernet work. Support for all 8 dma channels, gbit and the embedded switch
found on the ar9/vr9 still needs to be implemented.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2357/
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the DMA engine found inside the XWAY family of
SoCs. The engine has 5 ports and 20 channels.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2355/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.
[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.
The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.
[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable XLR CPU support, SMP, initramfs based root filesystem etc.
[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* include/asm/netlogic added with files common for all Netlogic processors
(common with XLP which will be added later)
* include/asm/netlogic/xlr for XLR/XLS chip specific files
* netlogic/xlr for XLR/XLS platform files
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Netlogic Microsystems company ID and processor IDs for XLR
and XLS processors for CPU probe. Add CPU_XLR to cpu_type_enum.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2367/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.
[ralf@linux-mips.org: Fixed the fix. The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
arch/ia64/kernel/cyclone.c
arch/mips/kernel/i8253.c
arch/x86/kernel/i8253.c
Reason: Resolve conflicts so further cleanups do not conflict further
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert MIPS i8253 clocksource code to use generic i8253 clocksource.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch drops the reference to a global 'cmd_line' variable from
early_init_dt_scan_chosen, and instead passes the pointer to the command
line string via the *data argument. Each architecture does something
slightly different with the initial command line, so it makes sense for
the architecture to be able to specify the variable name.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes:
alchemy/xxs1500/init.c: In function 'prom_init':
alchemy/xxs1500/init.c:57:17: error: ignoring return value of 'kstrtoul', declared with attribute warn_unused_result
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PAGE_SIZE >= 64kb (1 << 16) is too big to be the immediate of the
addiu/daddiu instruction, so, use addu/daddu instruction instead.
The following compiling error is fixed:
AS arch/mips/power/hibernate.o
arch/mips/power/hibernate.S: Assembler messages:
arch/mips/power/hibernate.S:38: Error: expression out of range
make[2]: *** [arch/mips/power/hibernate.o] Error 1
make[1]: *** [arch/mips/power] Error 2
Reported-by: Roman Mamedov <rm@romanrm.ru>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code for supporting one-shot mode for the clockevent is already there,
only the feature flag was not set. Setting the one-shot flag allows the
kernel to run in tickless mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/jz4740/dma.o
arch/mips/jz4740/dma.c: In function 'jz4740_dma_chan_irq':
arch/mips/jz4740/dma.c:245:11: error: variable 'status' set but not used [-Werro
r=unused-but-set-variable]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HOSTCC arch/mips/boot/compressed/calc_vmlinuz_load_addr
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c: In function 'main':
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:35:2: warning: format '%llx' expects type 'long long unsigned int *', but argument 3 has type 'uint64_t *'
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:54:2: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/devboards/db1x00/board_setup.o
arch/mips/alchemy/devboards/db1x00/board_setup.c: In function 'board_setup':
arch/mips/alchemy/devboards/db1x00/board_setup.c:130:6: error: variable 'pin_func' set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip27/ip27-hubio.o
arch/mips/sgi-ip27/ip27-hubio.c: In function 'hub_pio_map':
arch/mips/sgi-ip27/ip27-hubio.c:32:20: error: variable 'junk' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip27/ip27-hubio.o
arch/mips/sgi-ip27/ip27-hubio.c: In function 'hub_pio_map':
arch/mips/sgi-ip27/ip27-hubio.c:32:20: error: variable 'junk' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of making each Octeon specific option depend on
CPU_CAVIUM_OCTEON, gate the body of the entire file with
CPU_CAVIUM_OCTEON. With this change, CAVIUM_OCTEON_SPECIFIC_OPTIONS
becomes useless, so get rid of it as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon doesn't use IRQ_CPU, so don't select it.
IRQ_CPU_OCTEON is a completely unused symbol, remove it completely.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/loongson/common/env.o
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:50:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:51:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:52:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:53:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/jazz/jazzdma.o
arch/mips/jazz/jazzdma.c: In function 'vdma_remap':
arch/mips/jazz/jazzdma.c:214:20: error: variable 'npages' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sni/time.o
arch/mips/sni/time.c: In function 'dosample':
arch/mips/sni/time.c:98:19: error: variable 'lsb' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mti-malta/malta-int.o
arch/mips/mti-malta/malta-int.c: In function 'mips_pcibios_iack':
arch/mips/mti-malta/malta-int.c:59:6: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mti-malta/malta-init.o
arch/mips/mti-malta/malta-init.c: In function 'prom_init':
arch/mips/mti-malta/malta-init.c:196:6: error: variable 'result' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-platform.o
arch/mips/sgi-ip22/ip22-platform.c: In function 'sgiseeq_devinit':
arch/mips/sgi-ip22/ip22-platform.c:135:15: error: variable 'tmp' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
While at it rename the variable to pbdma for readability; there is a
local variable tmp of different type being used in two nested blocks.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-time.o
arch/mips/sgi-ip22/ip22-time.c: In function 'dosample':
arch/mips/sgi-ip22/ip22-time.c:35:10: error: variable 'lsb' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mm/tlbex.o
arch/mips/mm/tlbex.c: In function 'build_r4000_tlb_refill_handler':
arch/mips/mm/tlbex.c:1155:22: error: variable 'vmalloc_mode' set but not used [-Werror=unused-but-set-variable]
arch/mips/mm/tlbex.c:1154:28: error: variable 'htlb_info' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mm/c-r4k.o
arch/mips/mm/c-r4k.c: In function 'probe_scache':
arch/mips/mm/c-r4k.c:1078:6: error: variable 'tmp' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Older GCC versions didn't warn about the unused variable tmp because it was
getting initialized.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code is abusing the uasm interface by passing jump target
addresses with high bits set. Mask the addresses to avoid annoying
messages at boot time.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/perf_event.h
Merge reason: pick up the latest jump-label enhancements, they are cooked ready.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
The Atheros AR71XX/AR7240 SoCs have a built-in OHCI controller.
This patch adds the necessary glue code to make the generic OHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Atheros AR71XX/AR91XX SoCs have a built-in EHCI controller.
This patch adds the necessary glue code to make the generic EHCI
driver usable for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce:
static __always_inline bool static_branch(struct jump_label_key *key);
instead of the old JUMP_LABEL(key, label) macro.
In this way, jump labels become really easy to use:
Define:
struct jump_label_key jump_key;
Can be used as:
if (static_branch(&jump_key))
do unlikely code
enable/disale via:
jump_label_inc(&jump_key);
jump_label_dec(&jump_key);
that's it!
For the jump labels disabled case, the static_branch() becomes an
atomic_read(), and jump_label_inc()/dec() are simply atomic_inc(),
atomic_dec() operations. We show testing results for this change below.
Thanks to H. Peter Anvin for suggesting the 'static_branch()' construct.
Since we now require a 'struct jump_label_key *key', we can store a pointer into
the jump table addresses. In this way, we can enable/disable jump labels, in
basically constant time. This change allows us to completely remove the previous
hashtable scheme. Thanks to Peter Zijlstra for this re-write.
Testing:
I ran a series of 'tbench 20' runs 5 times (with reboots) for 3
configurations, where tracepoints were disabled.
jump label configured in
avg: 815.6
jump label *not* configured in (using atomic reads)
avg: 800.1
jump label *not* configured in (regular reads)
avg: 803.4
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110316212947.GA8792@redhat.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Suggested-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Make use of the IRQCHIP_ONOFFLINE_ENABLED flag and remove the
wrappers. Use irqd_irq_disabled() instead of desc->status, which will
go away.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Daney <ddaney@caviumnetworks.com>
This includes conversion to new style irq_chip functions, and
correctly enabling/disabling per-CPU interrupts.
The hardware interrupt bit to irq number mapping is now done with a
flexible map, instead of by bit twiddling the irq number.
[ tglx: Adjusted to new irq_cpu_on/offline callbacks and
__irq_set_affinity_lock ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <1301081931-11240-5-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These system calls we recently added.
32-bit ABIs need compat handling for sys_clock_adjtime().
o32 also needs compat handling for sys_open_by_handle_at();
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The conversion did not make use of the new chip flag which signals the
core code to mask the chip before calling the set_type callback. Sigh.
Use the new lockdep helper as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently there is one irq_chip per gpio_chip with the only difference
being the name. Since the information whether the irq belong to GPIO
bank A, B, C or D is not that important rewrite the code to simply use
a single irq_chip for all gpio_chips.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2182/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the JZ4740 intc and gpio irq chips to use newstyle irq functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the deadlock in set_type() while at it:
The code called set_irq_chip_and_handler_name() resp. set_irq_chip()
from the set_type() callback. That only works on UP and lock debugging
disabled. Otherwise it would dead lock on desc->lock.
__irq_set_chip_handler_name_locked() avoids that.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2173/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of MSP family SoC's come with legacy 100Mbps mspeth while some comes
with newer Gigabit TSMAC.Following patch adds platform support for both
types of MAC's.
If TSMAC is not selected assume platform having legacy mspeth. Add
gpio_macros as well which is required for resetting the PHY.
[Ralf: Killed all typedefs.]
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch will add vectored interrupt setups required for MIPS MT modes.
irq_cic has been restructured and moved per irq handler to different file.
irq_cic has been re wrote to support mips MT modes ( VSMP / SMTC )
[Ralf: fixed some more checkpatch warnings.]
Signed-off-by: Anoop P A <anoop.pa@gmail.com>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
To: dhowells@redhat.com
Patchwork: https://patchwork.linux-mips.org/patch/2041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
There is no user now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This introduces CONFIG_GENERIC_FIND_BIT_LE to tell whether to use generic
implementation of find_*_bit_le() in lib/find_next_bit.c or not.
For now we select CONFIG_GENERIC_FIND_BIT_LE for all architectures which
enable CONFIG_GENERIC_FIND_NEXT_BIT.
But m68knommu wants to define own faster find_next_zero_bit_le() and
continues using generic find_next_{,zero_}bit().
(CONFIG_GENERIC_FIND_NEXT_BIT and !CONFIG_GENERIC_FIND_BIT_LE)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
video: change to new flag variable
scsi: change to new flag variable
rtc: change to new flag variable
rapidio: change to new flag variable
pps: change to new flag variable
net: change to new flag variable
misc: change to new flag variable
message: change to new flag variable
memstick: change to new flag variable
isdn: change to new flag variable
ieee802154: change to new flag variable
ide: change to new flag variable
hwmon: change to new flag variable
dma: change to new flag variable
char: change to new flag variable
fs: change to new flag variable
xtensa: change to new flag variable
um: change to new flag variables
s390: change to new flag variable
mips: change to new flag variable
...
Fix up trivial conflict in drivers/hwmon/Makefile
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: booke_wdt: clean up status messages
watchdog: cleanup spaces before tabs
watchdog: convert to DEFINE_PCI_DEVICE_TABLE
watchdog: Xen watchdog driver
watchdog: Intel SCU Watchdog Timer Driver for Moorestown and Medfield platforms.
watchdog: jz4740_wdt - fix magic character checking
watchdog: add JZ4740 watchdog driver
watchdog: it87_wdt: Add support for IT8721F watchdog
watchdog: hpwdt: build hpwdt as module by default with NMI_DECODING enabled
watchdog: hpwdt: Fix a couple of typos
Make __get_user_pages return -EHWPOISON for HWPOISON page only if
FOLL_HWPOISON is specified. With this patch, the interested callers
can distinguish HWPOISON pages from general FAULT pages, while other
callers will still get -EFAULT for all these pages, so the user space
interface need not to be changed.
This feature is needed by KVM, where UCR MCE should be relayed to
guest for HWPOISON page, while instruction emulation and MMIO will be
tried for general FAULT page.
The idea comes from Andrew Morton.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: Add arch-specific this_cpu_cmpxchg_double() support
percpu: Generic support for this_cpu_cmpxchg_double()
alpha: use L1_CACHE_BYTES for cacheline size in the linker script
percpu: align percpu readmostly subsection to cacheline
Fix up trivial conflict in arch/x86/kernel/vmlinux.lds.S due to the
percpu alignment having changed ("x86: Reduce back the alignment of the
per-CPU data section")
* 'core-futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arm: Remove bogus comment in futex_atomic_cmpxchg_inatomic()
futex: Deobfuscate handle_futex_death()
plist: Add priority list test
plist: Shrink struct plist_head
futex,plist: Remove debug lock assignment from plist_node
futex,plist: Pass the real head of the priority list to plist_del()
futex: Sanitize futex ops argument types
futex: Sanitize cmpxchg_futex_value_locked API
futex: Remove redundant pagefault_disable in futex_atomic_cmpxchg_inatomic()
futex: Avoid redudant evaluation of task_pid_vnr()
futex: Update futex_wait_setup comments about locking
Adds support for the hardware watchdog found in Ingenic's jz4740
System-on-Chip.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To avoid forking usermode thread when creating an idle task, move fork_idle
to a work queue.
If kernel starts with maxcpus= option which does not bring all available
cpus online at boot time, idle tasks for offline cpus are not created. If
later offline cpus are hotplugged through sysfs, __cpu_up is called in
the context of the user task, and fork_idle copies its non-zero mm
pointer. This causes BUG() in per_cpu_trap_init.
This also avoids issues with resource limits of the CPU writing to sysfs,
containers, maybe others.
Signed-off-by: Maksim Rayskiy <mrayskiy@broadcom.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2070/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leverage the commit for ARM by Will Deacon:
- 446a5a8b1e
ARM: 6205/1: perf: ensure counter delta is treated as unsigned
Hardware performance counters on ARM are 32-bits wide but atomic64_t
variables are used to represent counter data in the hw_perf_event structure.
The armpmu_event_update function right-shifts a signed 64-bit delta variable
and adds the result to the event count. This can lead to shifting in sign-bits
if the MSB of the 32-bit counter value is set. This results in perf output
such as:
Performance counter stats for 'sleep 20':
18446744073460670464 cycles <-- 0xFFFFFFFFF12A6000
7783773 instructions # 0.000 IPC
465 context-switches
161 page-faults
1172393 branches
20.154242147 seconds time elapsed
This patch ensures that the delta value is treated as unsigned so that the
right shift sets the upper bits to zero.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2015/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Frederic Weisbecker:
- f72c1a931e
perf: Factorize callchain context handling
Store the kernel and user contexts from the generic layer instead
of archs, this gathers some repetitive code.
- 56962b4449
perf: Generalize some arch callchain code
- Most archs use one callchain buffer per cpu, except x86 that needs
to deal with NMIs. Provide a default perf_callchain_buffer()
implementation that x86 overrides.
- Centralize all the kernel/user regs handling and invoke new arch
handlers from there: perf_callchain_user() / perf_callchain_kernel()
That avoid all the user_mode(), current->mm checks and so...
- Invert some parameters in perf_callchain_*() helpers: entry to the
left, regs to the right, following the traditional (dst, src).
- 70791ce9ba
perf: Generalize callchain_store()
callchain_store() is the same on every archs, inline it in
perf_event.h and rename it to perf_callchain_store() to avoid
any collision.
This removes repetitive code.
- c1a65932fd
perf: Drop unappropriate tests on arch callchains
Drop the TASK_RUNNING test on user tasks for callchains as
this check doesn't seem to make any sense.
Also remove the tests for !current that is not supposed to
happen and current->pid as this should be handled at the
generic level, with exclude_idle attribute.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Patchwork: http://patchwork.linux-mips.org/patch/2014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commits by Peter Zijlstra:
- a4eaf7f146
perf: Rework the PMU methods
Replace pmu::{enable,disable,start,stop,unthrottle} with
pmu::{add,del,start,stop}, all of which take a flags argument.
The new interface extends the capability to stop a counter while
keeping it scheduled on the PMU. We replace the throttled state with
the generic stopped state.
This also allows us to efficiently stop/start counters over certain
code paths (like IRQ handlers).
It also allows scheduling a counter without it starting, allowing for
a generic frozen state (useful for rotating stopped counters).
The stopped state is implemented in two different ways, depending on
how the architecture implemented the throttled state:
1) We disable the counter:
a) the pmu has per-counter enable bits, we flip that
b) we program a NOP event, preserving the counter state
2) We store the counter state and ignore all read/overflow events
For MIPSXX, the stopped state is implemented in the way of 1.b as above.
- 33696fc0d1
perf: Per PMU disable
Changes perf_disable() into perf_pmu_disable().
- 24cd7f54a0
perf: Reduce perf_disable() usage
Since the current perf_disable() usage is only an optimization,
remove it for now. This eases the removal of the __weak
hw_perf_enable() interface.
- b0a873ebbf
perf: Register PMU implementations
Simple registration interface for struct pmu, this provides the
infrastructure for removing all the weak functions.
- 51b0fe3954
perf: Deconstify struct pmu
sed -ie 's/const struct pmu\>/struct pmu/g' `git grep -l "const struct pmu\>"`
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: a.p.zijlstra@chello.nl
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: wuzhangjin@gmail.com
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: dengcheng.zhu@gmail.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com
Cc: ddaney@caviumnetworks.com
Patchwork: http://patchwork.linux-mips.org/patch/2012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS part of the following commit by Peter Zijlstra:
- e360adbe29
irq_work: Add generic hardirq context callbacks
Provide a mechanism that allows running code in IRQ context. It is
most useful for NMI code that needs to interact with the rest of the
system -- like wakeup a task to drain buffers.
Perf currently has such a mechanism, so extract that and provide it as
a generic feature, independent of perf so that others may also
benefit.
The IRQ context callback is generated through self-IPIs where
possible, or on architectures like powerpc the decrementer (the
built-in timer facility) is set to generate an interrupt immediately.
Architectures that don't have anything like this get to do with a
callback from the timer tick. These architectures can call
irq_work_run() at the tail of any IRQ handlers that might enqueue such
work (like the perf IRQ handler) to avoid undue latencies in
processing the work.
For MIPSXX, we need to call irq_work_run() at the tail of the perf IRQ
handler as described above.
Reported-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: fweisbec@gmail.com
To: will.deacon@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: matt@console-pimps.org
Cc: sshtylyov@mvista.com,
Patchwork: http://patchwork.linux-mips.org/patch/2011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This error was reported by cppcheck:
arch/mips/loongson/common/machtype.c:56: error: Dangerous usage of 'str' (strncpy doesn't always 0-terminate it)
If strncpy copied MACHTYPE_LEN bytes, the destination string str
was not terminated.
The patch adds one more byte to str and makes sure that this byte is
always 0.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2053/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Under some combinations of CONFIG_*, lastpfn in page_is_ram is 'set
but not used'. Mark it as __maybe_unused to quiet the warning/error.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of arch/mips/math-emu/ieee754int.h, the COMPXSP and
COMPXDP macros are used in several places, but a couple of them leave
xs unused. The easiest thing to do is mark it as __maybe_unused to
quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GCC-4.6 can find more unused code than previous versions could.
In the case of protected_restore_fp_context{,32}, the variable tmp is
really used. Its use is tricky in that we really care about the side
effects of the __put_user() calls. So we must mark tmp with
__maybe_unused to quiet the warning.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson builds have an ad-hoc cmdline default of "console=ttyS0,115200
root=/dev/hda1". These settings come from a vendor; I remember builds
from Lemote branch requiring a "console=tty" override in order to get a
working console.
At least on Yeeloong, they're particularly useless: there's no external
serial port, and the IDE drive is now recognised as /dev/sda.
Signed-off-by: Robert Millan <rmh@gnu.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sysmips(MIPS_FIXADE, ...) case contains an obvious copy-and-paste
error in the handling of the TIF_LOGADE flag. Fix that
Patchwork: https://patchwork.linux-mips.org/patch/1997/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was reported that GCC-4.3.3 (with CodeSourcery extensions) fails
without this.
Reported-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trace.func should be set to the recorded ip of the mcount calling site
in the __mcount_loc section to filter the function entries configured
through the tracing/set_graph_function interface, but before, this is
set to the self_ra(the return address of mcount), which has made
set_graph_function not work as expected.
This fixes it via calculating the right recorded ip in the __mcount_loc
section and assign it to trace.func.
Reported-by: Zhiping Zhong <xzhong86@163.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2017/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
This moves the comments out of ftrace_make_nop() and cleans it. At the
same time, a macro MCOUNT_OFFSET_INSNS is defined for sharing with the
next patch.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2008/
Signed-off-by: Ralf Baechle <ralf@duck.linux-mips.net>
