Register the PLL configuration data for APLL and KPLL on Exynos5420. This
configuration data table specifies PLL coefficients for supported PLL
clock speeds when a 24MHz clock is supplied as the input clock source
for these PLLs.
Cc: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Arjun K.V <arjun.kv@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Prior to suspending the system, we need to ensure that certain
clock source and gate registers are unmasked.
while at it, add these clks to save/restore list also.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Array of struct of_device_id may be be const as expected by
of_match_table field and of_find_matching_node_and_match() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Enable ARMCLK down feature on Exynos3250 SoC. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor.
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Enable ARMCLK down feature on all Exynos4 SoCs. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).
The feature behaves like very fast cpufreq ondemand governor. In idle
mode this reduces energy consumption on full frequency chosen by
cpufreq governor by approximately:
- Trats2: 6.5% (153 mA -> 143 mA)
- Trats: 33.0% (180 mA -> 120 mA)
- Gear1: 27.0% (180 mA -> 130 mA)
The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature and on Exynos4412 ARMCLK down is
enabled for all 4 cores.
Tested on Trats board (Exynos4210), Trats2 board (Exynos4412) and
Samsung Gear 1 (Exynos4212).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch introduces a driver that handles configuration of CLKOUT pin
of Exynos SoCs that can be used to output certain clocks from inside of
the SoC to a dedicated output pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds definitions of clocks that are used to drive clock
output signals of particular CMU sub-blocks that are then fed to PMU and
handled by Exynos CLKOUT driver added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds missing definitions of clocks from CPU and DMC clock
domains, which are necessary to properly represent CLKOUT clock hierarchy
added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Exynos4 has saveral PPMUs and each of them has operation clock which
can be gated through CMU's SFR control.
New clocks are listed below. All clocks are added as a gate-typed clock.
CLK_PPMULEFT, CLK_PPMURIGHT, CLK_PPMUCAMIF, CLK_PPMUTV, CLK_PPMUMFC_L,
CLK_PPMUMFC_R, CLK_G3D, CLK_PPMUIMAGE, CLK_PPMULCD0, CLK_PPMULCD1,
CLK_PPMUFILE, CLK_PPMUGPS, CLK_PPMUDMC0, CLK_PPMUDMC1, CLK_PPMUCPU,
CLK_PPMUACP,
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Ensure the clock provider is not registered until after all its related
clocks were created and are ready to use. Currently there are races
possible and any (of_)clk_get() call right after a clock provider's
clk_init_cb callback call may fail.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The "aclk66_peric" clock is a gate clock with a whole bunch of gates
underneath it. This big gate isn't very useful to include in our
clock tree. If any of the children need to be turned on then the big
gate will need to be on anyway. ...and there are plenty of other "big
gates" that aren't described in our clock tree, some of which shut off
collections of clocks that have no relationship in the hierarchy so
are hard to model.
"aclk66_peric" is causing earlyprintk problems since it gets disabled
as part of the boot process, so let's just remove it.
Strangely (and for no good reason) this clock is exported as part of
the common clock bindings. Remove it since there are no in-kernel
device trees using it and no reason anyone out of tree should refer to
it either.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Change bit from 2 to 9 for tv (mixer) sysmmu clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
In the move to this clock driver the hookups for the SPI clocks were
dropped, which causes my system Cragganmore (s3c6410 based) to be unable
to locate any spibus clocks. This patch adds them back in.
When taking the clock from the epll clock (SCLK) the rates on the SPI
bus are incorrect, this needs further debugging but the hookup here
should be correct and the problem should be else where.
The USBCLK case has been dropped because this requires the USB PHY to be
enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
ISP special clocks have dedicated gating registers and so MUX SRC_MASK
register should not be used. This patch fixes the problem of
Exynos4x12-based boards freezing on system suspend, because those
mux outputs need not to be masked while suspending.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
There's a several typos in a driver: 2410 instead of S3C2410
and wrong argument to ARRAY_SIZE(). They prevent s3c2410
from properly booting.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
driver additions and fixes. There are additions to the clock core code
for some of the basic types (e.g. the common divider type has some fixes
and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. ba0fae3 in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTkhd7AAoJEDqPOy9afJhJ/kAQAKJt4slFYNW5t69HBmqlfkxR
1Y61KqTaZiJ2XNqudNUDd6GkD5CW0pqD194dOXOLQMSGIZ3i+mHJ91ddV4x7J8xe
+eAvaHqDc4XJyJouzOOxx2LhnThRUkpyXLzbXTITIoy4nK6K+ANg6hPjfBwTDs3m
7dDu+WDYAN4EMjMffpPD26axl778H5FXzqJaKx+RmMDw6f3y6g+8hKCvSicetpAa
AnTLhx8q4kbEmOZHOEny28KliOpDAMPd/nNcnjqpfKBSoq0J6aYGM0t5bUH+clY9
nzjgMfE+pRm8N+oyssNCqT99ebeIxSF6Ps/EVZRJCETUi3s0n1/Y4dK3uPNOyo+G
BSv0wfQ5M1IebmnIIlQuJ+zNvtKFkoLoi1Q/fsOr51HVfddwrEbd972+zYdjSeVe
RXRb3HAStfQEjp0874VD9wr6u0tHskUrQGzHSSs8PNsfCv/URwJUPuS7XnePPXAZ
KdtJST/b+WiY96pPJDLc44trRko1opxgncYqsusnWtwsUzK5aKnAbbYSiTIZhxJU
44p7/xOokeTcgDuluEk8mR+PEX5EhGokYXOVXfSCMJOXehpHnpMHtzCieTcmJ9Ir
NaOATHjSXwHI7jiv/W+EZQnZCnoHnST+GT4FtmjYkD3lzMpK9d/E9mxjKs8hUNgO
xH71k4uL7WljxsVWp/16
=2AAL
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
This is including fix exynos cpufreq driver compilation with
ARCH_MULTIPLATFORM. Even though this is a work around, this
is required for support exynos multiplatform for a while and
will be updated in near future.
This is based on tags/samsung-exynos.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SQbr
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung 2nd drivers for 3.16" from Kukjin Kim:
This is including fix exynos cpufreq driver compilation with
ARCH_MULTIPLATFORM. Even though this is a work around, this
is required for support exynos multiplatform for a while and
will be updated in near future.
This is based on tags/samsung-exynos.
* tag 'samsung-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (24 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: dts: Remove g2d_pd node for exynos5420
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixes the following warning:
WARNING: drivers/built-in.o(.text.unlikely+0x2c50): Section mismatch in reference from the function exynos4_clk_sleep_init() to the (unknown reference) .init.data:(unknown)
The function exynos4_clk_sleep_init() references
the (unknown reference) __initdata (unknown).
This is often because exynos4_clk_sleep_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
"clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares
__initdata" had a typo in it which caused build failure. Trivial fix.
Signed-off-by: Olof Johansson <olof@lixom.net>
The originally used PNAME macro from the core samsung clock infrastructure
declares the created array as initdata, creating section mismatch warnings
in the dclk driver.
Thus declare them directly, removing these warning.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the missing sysmmu clocks for Display and
ISP blocks.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now with common clock support added for exynos5250 it is necessary to
move this code to exynos5250 common clock driver as clock registers
should be handled there. This change is tested in exynos5250 based
arndale platform.
Cc: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsugn.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[t.figa: Rebased onto current kernel sources.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5800 clock structure is mostly similar to 5420 with only
a small delta changes. So the 5420 clock file is re-used for
5800 also. The common clocks for both are seggreagated and few
clocks which are different for both are separately initialized.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add new the clock drvier of Exynos3250 SoC based on Cortex-A7
using common clock framework. The CMU (Clock Management Unit) of Exynos3250
control PLLs(Phase Locked Loops) and generate system clocks for CPU, buses,
and function clocks for individual IPs.
The CMU of Exynos3250 includes following clock doamins:
- CPU block for Cortex-A7 MPCore processor
- LEFTBUS/RIGHTBUS block
- TOP block for G3D/MFC/LCD0/ISP/CAM/FSYS/MFC/PERIL/PERIR
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hyunhee Kim <hyunhee.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
This patch moves S3C24XX specific clock Kconfig options into
"clk/samsung/Kconfig" and also removes COMMON_CLK selection from
"mach-s3c24xx/Kconfig" as S3C24XX_COMMON_CLK is selecting it's dependency.
CC: Ben Dooks <ben-linux@fluff.org>
CC: Kukjin Kim <kgene.kim@samsung.com>
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds new Kconfig file for adding new COMMON_CLK_SAMSUNG option.
Samsung platforms can select this for using common clock infrastructure.
CC: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds more register offsets to the list for
preserving their values during S2R.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds some missing miscellaneous clocks specific
to exynos5420.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds the missing MAU block specific clocks.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch corrects the wrong parent-child relationship
between sysmmu-mfc clocks.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds more clocks from FSYS and FSYS2 blocks
and uses GATE_IP_* registers for gating IPs.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch fixes some parent-child relationships according
to the latest datasheet and adds more clocks related to
PERIS and GEN blocks.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch includes,
1] renaming of the HSI2C clocks
2] renaming of spi clocks according to the datasheet
3] fixes for child-parent relationships
4] adding of more clocks related to PERIC block
5] use GATE_IP_* offsets instead of GATE_BUS_*
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch corrects some child-parent clock relationships,
and updates the clocks according to the latest datasheet.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds missing clocks of G2D block. It also removes
the aclkg3d alias from G3D block clocks.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds the missing GSCL and MSCL block clocks
and corrects some wrong parent-child relationships.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds minimum set of clocks to gate ISP block for
power saving.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch renames the mux parent arrays as per the naming
convension followed by the other exynos specific clock drivers.
And it also renames "mout_cpu_kfc" clock to "mout_kfc".
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Adds IDs for the clocks needed by the ARM Mali GPU
in exynos5420.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Export sclk_hdmiphy clock to be usable from DT.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This patch adds the required clocks for ARM Mali IP
in Exynos5250.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
[t.figa: Changed clock ID to avoid conflict with CLK_SSS]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Exynos4210 and Exynos4x12 SoCs have the PL330 MDMA IP block clock
defined exactly in same way in documentation. Using different
names for these clocks is a bit misleading. Since there is no users
of CLK_MDMA2 in existing dts files this patch drops CLK_MDMA2 and
replaces it with CLK_MDMA in the driver. This ensures PL330 MDMA
has correct clock assigned on Exynos4x12 SoCs.
Suggested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
When compiled using ARM64 cross compiler, gcc complains as
drivers/clk/samsung/clk.c:293:18:
warning: cast from pointer to integer of different size
[-Wpointer-to-int-cast]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
