The board uses hardwired timings compatible with 72Hz DEC VR319-DA and
VRM17-AA monitors, according to the board owner's manual[1]. These
timings are accordingly taken from the VR319 manual[2].
References:
[1] "The Monochrome Frame Buffer TURBOchannel Module", Digital Equipment
Corporation, Order Number: EK-MFBOM-TC-001, December 1991
[2] "Installing and Using the VR319 Monochrome Monitor", Digital
Equipment Corporation, Order Number: EK-VR319-IN-001, First Edition,
January 1990, Table 6-1 "Video Timing--1280 x 1024 Resolution"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the current TURBOchannel API support is automagical.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rework the driver to use the current frambuffer and TURBOchannel APIs,
including proper resource management and using the new framework for
hardware cursor support.
NB two Bt431 cursor generators are included onboard, both responding at
the same TURBOchannel bus addresses and with their host data buses wired
to byte lanes #0 and #1 respectively of the 32-bit bus. Therefore both
can be accessed simultaneously with 16-bit data transfers. Cursor
outputs of the chip wired to lane #0 drive the respective overlay select
inputs of the Bt455 RAMDAC, whereas cursor outputs of the chip wired to
lane #1 drive the respective P3 pixel select inputs of the RAMDAC.
So 5 (out of 17) Bt455 color registers are usable with this board:
palette entries #0 and #1 for frame buffer pixel data driven while
neither cursor generator is active, palette entries #8 and #9 for frame
buffer pixel data driven while cursor generator #1 is active only and
the overlay entry while cursor generator #0 is active.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the board specification[1] the width of the vertical sync
front porch is 12 pixels or the same as the width of the horizontal sync
front porch. This in turn means the size of the lower margin is 0,
because the vertical sync starts as soon as the start of the horizontal
sync terminates the last line.
References:
[1] "PMAG-BA TURBOchannel Color Frame Buffer Functional Specification",
Revision 1.2, Workstation Systems Engineering, Digital Equipment
Corporation, August 27, 1990, Table 3-5: "Video Timing"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We were not checking the return value of platform_device_add_data()
which can fail.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As the function name already indicates that get_opt_bool() parses
for a bool. It is not a surprise that compiler is complaining
about it when -Werror=incompatible-pointer-types is used:
drivers/video/fbdev/intelfb/intelfbdrv.c: In function ‘intelfb_setup’:
drivers/video/fbdev/intelfb/intelfbdrv.c:353:39: error: passing argument 3 of ‘get_opt_bool’ from incompatible pointer type [-Werror=incompatible-pointer-types]
if (get_opt_bool(this_opt, "accel", &accel))
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
par->metromem_cmd->args[] is an array of 31 elements of size u16. Here
we have initialized the first "i" elements and want to set the rest to
zero.
The issue here is that ARRAY_SIZE(par->metromem_cmd->args) is 31 and not
32 as in the original code. It means that we set ->csum to zero, but
that is harmless because we immediately set it to the correct value on
the next line.
Still, the buffer overflow upsets static checkers so let's correct the
math.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We will soon modify the vanilla get_user_pages() so it can no
longer be used on mm/tasks other than 'current/current->mm',
which is by far the most common way it is called. For now,
we allow the old-style calls, but warn when they are used.
(implemented in previous patch)
This patch switches all callers of:
get_user_pages()
get_user_pages_unlocked()
get_user_pages_locked()
to stop passing tsk/mm so they will no longer see the warnings.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: jack@suse.cz
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210156.113E9407@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers should include asm/pci-bridge.h only when they need the arch-
specific things provided there. Outside of the arch/ directories, the only
drivers that actually need things provided by asm/pci-bridge.h are the
powerpc RPA hotplug drivers in drivers/pci/hotplug/rpa*.
Remove the includes of asm/pci-bridge.h from the other drivers, adding an
include of linux/pci.h if necessary.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently when we boot the kernel on a mx25pdk the LCDC controller
does not show the Linux logo on boot.
This problem is well explained by Sascha Hauer:
"Unfortunately this LCD controller does not have an enable bit. The
controller starts directly when the clocks are enabled. If the clocks
are enabled when the controller is not yet programmed with proper
register values then it just goes into some undefined state. What I
suspect is that the clocks already were enabled before driver probe,
presumably by the bootloader, so the controller is already in undefined
state when entering Linux. Now by dis/enabling the ipg clock you
effectively reset the controller. Since you have programmed it with
valid register values in the mean time it starts working after this
reset."
So do as suggested and force a reset of the LCDC hardware by
enabling and disabling the IPG clock.
With this change the Linux logo can be seen on boot on a mx25pdk.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
resource_size_t cannot be printed using the %x format string
when we it is defined as u64:
drivers/video/fbdev/mmp/hw/mmp_ctrl.c: In function 'mmphw_probe':
drivers/video/fbdev/mmp/hw/mmp_ctrl.c:506:22: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
dev_err(ctrl->dev, "%s: res %x - %x map failed\n", __func__,
^
drivers/video/fbdev/mmp/hw/mmp_ctrl.c:506:22: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
This changes the format string to %pR, which is interpreted
by the printk implementation to pretty-print a resource
structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The probe function correct passes a dma_addr_t pointer into
dma_alloc_coherent(), but has a cast to resource_size_t, which
might be different from dma_addr_t:
drivers/video/fbdev/da8xx-fb.c: In function 'fb_probe':
drivers/video/fbdev/da8xx-fb.c:1431:10: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
This removes the cast, which avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The s6e8ax0 suspend/resume functions are hidden inside of an #ifdef
when CONFIG_PM is set to avoid unused function warnings, but they
call some other functions that nothing else calls, and we get warnings
about those:
drivers/video/fbdev/exynos/s6e8ax0.c:449:13: error: 's6e8ax0_sleep_in' defined but not used [-Werror=unused-function]
drivers/video/fbdev/exynos/s6e8ax0.c:485:13: error: 's6e8ax0_display_off' defined but not used [-Werror=unused-function]
This marks the PM functions as __maybe_unused so the compiler can
silently drop them when they are not referenced.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to the ocfb documentation:
Fix tgdel HW param should be left margin, not right.
Fix tvdel HW param should upper margin, not lower.
This seems to fix lock issues on certain monitors (tested on a
slightly customized IP, but the FPGA guy said that it should
be the same wrt this changes).
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
As seen by Julia, the initial allocation memory is not checked anymore
after commit "video: fbdev: pxafb: initial devicetree conversion".
Introduce back the removed test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that omapfb has its own copy of omapdss and display drivers, we can
move omapdss and display drivers which omapdrm uses to omapdrm's
directory.
We also need to change the main drm Makefile so that omapdrm directory
is always entered, because omapdss has a file that can't be built as a
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
VRFB is only used by omapfb, so we can move it under omapfb's directory.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
omapfb's private copy of omapdss is now ready to be used.
This patch makes omapfb use its private omapdss and display drivers, and
also makes omap_vout (which uses omapfb) to depend on omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
We need to change the config symbols of omapfb's private copy of the
panel and encoder drivers so that we won't have config symbol conflicts.
This patch changes the symbols from the panel and encoder drivers using
simple replacement of DISPLAY_* to FB_OMAP2*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
We need to change the config symbols of omapfb's private copy of
omapdss so that we won't have config symbol conflicts.
This patch changes the symbols from omapdss using simple replacement of
CONFIG_OMAP* to CONFIG_FB_OMAP*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
This patch makes a copy of the omapdss driver and the omap panel &
encoder drivers for omapfb. The purpose is to separate omapdrm and
omapfb drivers from each other.
Note that this patch only does a direct copy of the files without any
other modifications. The files are not yet used.
The original files are in:
drivers/video/fbdev/omap2/dss/
drivers/video/fbdev/omap2/displays-new/
Here's a more detailed explanation about this and the following patches,
from the introduction mail of the patch series:
A short background on the current status. We have the following
entities:
* omapdss, located in drivers/video/fbdev/omap2/dss/. This is a driver for the
display subsystem IPs used on OMAP (and related) SoCs. It offers only a
kernel internal API, and does not implement anything for fbdev or drm.
* omapdss panels and encoders, located in
drivers/video/fbdev/omap2/displays-new/. These are panel and external encoder
drivers, which use APIs offered by omapdss driver. These also don't implement
anything for fbdev or drm.
* omapdrm, located in drivers/gpu/drm/omapdrm/. This is a drm driver, which
uses omapdss and the panel/encoder drivers to operate the hardware.
* omapfb, located in drivers/video/fbdev/omap2/omapfb/. This is an fbdev
driver, which uses omapdss and the panel/encoder drivers to operate the
hardware.
* omap_vout, located in drivers/media/platform/omap/. This is a v4l2 driver,
which uses omapdss and omapfb to implement a v4l2 API for the video overlays.
So, on the top level, we have either omapdrm, or omapfb+omap_vout. Both of
those use the same low level drivers. Without going to the historical details
why the architecture is like that, I think it's finally time to change that.
The situation with omapfb+omap_vout is that it still works, but no new features
have been added for a long time, and I want to keep it working as it's still
being used. At some point in the future I'd like to remove omapfb and
omap_vout altogether.
Omapdrm, on the other hand, is being actively developed. Sharing the low level
parts with omapfb makes that development more difficult than it should be. It
also "hides" half of the development, as everything happening in the low level
parts resides under fbdev directory, not in the drm directory.
I've been wanting to clean this up for a long time, but I haven't figured out a
very good way to do it. I still haven't, but here's the best way I have come up
with.
This series makes a full copy of the low level parts, omapdss and panel/encoder
drivers. Both omapfb+omap_vout and omapdrm will have their own versions. The
copy omapfb+omap_vout get is a new copy, and the copy that omapdrm gets is just
the current files moved. This way git will associate the omapdrm version with
the old files.
The omapfb+omap_vout versions won't be touched unless there are some big issues
there.
The omapdrm versions can be refactored and cleaned up, as the omapfb support
code is no longer needed. We can perhaps also merge omapdss and omapdrm into
the same kernel module.
This series only does the copy, and the absolutely necessary parts. No further
cleanups are done yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
At the moment omapfb and omapdrm can be compiled at the same time, if
both are modules. However, they can't be both loaded, as they use the
same hardware. This has been mostly for compile testing.
To make it clear that omapfb and omapdrm are mutually exclusive drivers,
this patch makes omapfb available only if omapdrm is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
gpiod_set_value_cansleep is a noop when the passed descriptor is NULL.
So there is no need to duplicate the check for NULL; just call the
function unconditionally instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This makes .disable operate in reverse order compared to .enable.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The WARN() macro has to take a condition. The current code will just
print the stack trace and the function name instead of the intended
warning message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Device node iterators perform an of_node_put on each iteration, so putting
an of_node_put before a continue results in a double put.
A simplified version of the semantic match that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator i;
@@
i(..., child, ...) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Boolean tests do not need explicit comparison to true or false.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSI_IRQ_SYNC_LOST was ORed twice so we can remove one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the output drivers check for 'out' being NULL, but it can never be
NULL. Remove the check.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
A bunch of dispc functions are only used inside dispc, so we can make
them static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
dss_feat_get_supported_displays() and dss_feat_get_supported_outputs()
are not used outside omapdss, but are exported. We can thus remove the
export and move the declarations to the omapdss internal header.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds are exported, but not declared in
public headers, and thus are not used outside omapdss. So we can remove
the EXPORT_SYMBOL()s.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
dispc_wb_setup() handles configuration only for mem-to-mem case. This
patch adds the necessary configuration to handle also display capture
mode.
We need to set CAPTUREMODE to 0 (continuous capture), and WBDELAYCOUNT
according to the vertical timings of the display, so that the WB FIFO
has time to flush before the next frame starts.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The color conversion coefficients for RGB to YUV conversion (used with
writeback) don't result in the correct result. This patch sets the
correct coefficients.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When doing mem-to-mem writeback, there's no pixelclock. However, the
code that calculates scaling factors check that there is a pixel clock.
We can just skip the check when doing mem-to-mem writeback.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Mflag thresholds for all pipelines are set in dispc_init_mflag(), but we
are missing that for WB pipeline. Add WB configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds for all pipelines are set in dispc_init_fifos(), but we
are missing it for WB pipeline. Add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Burst size for all pipelines is set in dispc_configure_burst_sizes(),
but we are missing WB pipe. So add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add handling of OMAP_DSS_CHANNEL_WB to dispc_ovl_set_channel_out() and
dispc_ovl_get_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Refactor dispc_ovl_get_channel_out() to a bit cleaner form, which makes
it easier to add support for writeback in the following patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we have a function to get the number of writeback
pipelines supported. However, the function is used in a wrong way,
causing a wrong pipeline to get configured when trying to use WB. Also,
we only have a single writeback pipeline on any of the DSS versions.
To fix and simplify this, create a 'has_writeback' flag into the dispc
driver, and after checking the flag, use OMAP_DSS_WB pipeline
explicitly when calling the configuration functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5+ DSS has a writeback pipeline, but this was not specified in the
features list for OMAP5 DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
By default DISPC asserts hsync and vsync sequentially, i.e. there's
first hsync and that is immediately followed by vsync. This is the only
available behaviour on OMAP2/3, and default behaviour on OMAP4+.
OMAP4+ has ALIGN bit in POL_FREQ register, which makes DISPC assert both
syncs at the same time.
It has been observed that some panels don't like sequential syncs (AM5
EVM's panel). After studying the datasheets for multiple panels and
encoders, and MIPI DPI spec, it looks like there is no standard way to
handle this.
Sometimes the datasheets don't mention the required syncs behaviour at
all, sometimes the datasheets have images that hint towards simultaneous
syncs, and sometimes it is explicitly mentioned that simultaneous syncs
are needed. No panels or encoders requiring sequential sync was found.
It thus seems to be safe to default to simultaneous syncs when the ALIGN
bit is available. This fixed AM5 EVM's panel, and no side effects have
been observed on other panels or encoders.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Update omapdss driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch brings a first support of pxa framebuffer devices to a
devicetree pxa platform, as was before platform data.
There are restrictions with this port, the biggest one being the lack of
support of smart panels. Moreover the conversion doesn't provide a way
to declare multiple framebuffer configurations with different bits per
pixel, only the LCD hardware bus width is used.
The patch was tested on both pxa25x, pxa27x and pxa3xx platform (namely
lubbock, mainstone and zylonite).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to prepare the transition to a mixed platform data and
device-tree initialization, remove all the platform data references all
over the driver.
Copy the platform data into the internal structure of the pxafb, and
only use this afterward.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no point in having support for framebuffer notifications
is CONFIG_FB is disabled. This commit adds the necessary stubs
for code to link properly when CONFIG_FB=n and moves fb-notify.o
to be built only when CONFIG_FB=y.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the usual fbcon legacy options are enabled we have
->register_framebuffer
->fb notifier chain calls into fbcon
->fbcon sets up console on new fbi
->fbi->set_par
->drm_fb_helper_set_par exercises full kms api
And because of locking inversion hilarity all of register_framebuffer
is done with the console lock held. Which means that the first time on
driver load we exercise _all_ the kms code (all probe paths and
modeset paths for everything connected) is under the console lock.
That means if anything goes belly-up in that big pile of code nothing
ever reaches logfiles (and the machine is dead).
Usual tactic to debug that is to temporarily remove those console_lock
calls to be able to capture backtraces. I'm fed up writing this patch
and recompiling kernels. Hence this patch here to add an unsafe,
kernel-taining option to do this at runtime.
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At least NV3 requires for chip to be unlocked before it is possible to
access I2C registers. Without it, it is not possible to read EDID.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sm712fb framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the smtcfb_pci_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
fbdev/sm712fb.c:1549:12: warning: 'smtcfb_pci_suspend' defined but not used
fbdev/sm712fb.c:1572:12: warning: 'smtcfb_pci_resume' defined but not used
The driver also avoids using the SIMPLE_DEV_PM_OPS macro when
CONFIG_PM is unset, which is redundant.
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The auo_k190x framebuffer driver encloses the power-management
functions in #ifdef CONFIG_PM, but the auok190x_suspend/resume
functions are only really used when CONFIG_PM_SLEEP is also
set, as a frequent gcc warning shows:
drivers/video/fbdev/auo_k190x.c:859:12: warning: 'auok190x_suspend' defined but not used
drivers/video/fbdev/auo_k190x.c:899:12: warning: 'auok190x_resume' defined but not used
This changes the driver to remove the #ifdef and instead mark
the functions as __maybe_unused, which is a nicer anyway, as it
provides build testing for all the code in all configurations
and is harder to get wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sis framebuffer driver complains with a compile-time warning
if neither the FB_SIS_300 nor FB_SIS_315 symbols are selected:
drivers/video/fbdev/sis/sis_main.c:61:2: warning: #warning Neither CONFIG_FB_SIS_300 nor CONFIG_FB_SIS_315 is se
This is reasonable because it doesn't work in that case, but it's
also annoying for randconfig builds and is one of the most common
warnings I'm seeing on ARM now.
This changes the Kconfig logic to prevent the silly configuration,
by always selecting the FB_SIS_300 variant if the other one is
not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As of commit 44d88c754e ("ARM: shmobile: Remove legacy SoC code
for R-Mobile A1"), the SH-Mobile HDMI driver is no longer used.
In theory it could still be used on R-Mobile A1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These geode ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This claims and enables regulators listed in the simple framebuffer dt
node. This is needed so that regulators powering the display pipeline
and external hardware, described in the device node and known by the
kernel code, will remain properly enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The value of d_best is always 0 and never changes.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Otherwise check_timings fails and we get a "has no modes" message
from xrandr.
This fix makes the venc assume PAL and NTSC timings that match the
timings synthetized by copy_timings_drm_to_omap() from omapdrm
mode settings so that check_timings() succeeds.
Tested on: BeagleBoard XM, GTA04 and OpenPandora
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If diu_ops is not implemented on platform, kernel will access a NULL
pointer. We need to check this pointer in DIU initialization.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway - Paul Gortmaker
* Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64 - Leif Lindholm
* Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses - Matt Fleming
* Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
* Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module - Ben Hutchings
* Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support - Taku Izumi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Oee
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into core/efi
Pull v4.4 EFI updates from Matt Fleming:
- Make the EFI System Resource Table (ESRT) driver explicitly
non-modular by ripping out the module_* code since Kconfig doesn't
allow it to be built as a module anyway. (Paul Gortmaker)
- Make the x86 efi=debug kernel parameter, which enables EFI debug
code and output, generic and usable by arm64. (Leif Lindholm)
- Add support to the x86 EFI boot stub for 64-bit Graphics Output
Protocol frame buffer addresses. (Matt Fleming)
- Detect when the UEFI v2.5 EFI_PROPERTIES_TABLE feature is enabled
in the firmware and set an efi.flags bit so the kernel knows when
it can apply more strict runtime mapping attributes - Ard Biesheuvel
- Auto-load the efi-pstore module on EFI systems, just like we
currently do for the efivars module. (Ben Hutchings)
- Add "efi_fake_mem" kernel parameter which allows the system's EFI
memory map to be updated with additional attributes for specific
memory ranges. This is useful for testing the kernel code that handles
the EFI_MEMORY_MORE_RELIABLE memmap bit even if your firmware
doesn't include support. (Taku Izumi)
Note: there is a semantic conflict between the following two commits:
8a53554e12 ("x86/efi: Fix multiple GOP device support")
ae2ee627dc ("efifb: Add support for 64-bit frame buffer addresses")
I fixed up the interaction in the merge commit, changing the type of
current_fb_base from u32 to u64.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The EFI Graphics Output Protocol uses 64-bit frame buffer addresses
but these get truncated to 32-bit by the EFI boot stub when storing
the address in the 'lfb_base' field of 'struct screen_info'.
Add a 'ext_lfb_base' field for the upper 32-bits of the frame buffer
address and set VIDEO_TYPE_CAPABILITY_64BIT_BASE when the field is
useable.
It turns out that the reason no one has required this support so far
is that there's actually code in tianocore to "downgrade" PCI
resources that have option ROMs and 64-bit BARS from 64-bit to 32-bit
to cope with legacy option ROMs that can't handle 64-bit addresses.
The upshot is that basically all GOP devices in the wild use a 32-bit
frame buffer address.
Still, it is possible to build firmware that uses a full 64-bit GOP
frame buffer address. Chad did, which led to him reporting this issue.
Add support in anticipation of GOP devices using 64-bit addresses more
widely, and so that efifb works out of the box when that happens.
Reported-by: Chad Page <chad.page@znyx.com>
Cc: Pete Hawkins <pete.hawkins@znyx.com>
Acked-by: Peter Jones <pjones@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
With this .config: http://busybox.net/~vda/kernel_config,
after uninlining these functions have sizes and callsite counts
as follows:
__OUTPLLP: 61 bytes, 12 callsites
__INPLL: 79 bytes, 150 callsites
__OUTPLL: 82 bytes, 138 callsites
_OUTREGP: 101 bytes, 8 callsites
_radeon_msleep: 66 bytes, 18 callsites
_radeon_fifo_wait: 83 bytes, 24 callsites
_radeon_engine_idle: 92 bytes, 10 callsites
radeon_engine_flush: 105 bytes, 2 callsites
radeon_pll_errata_after_index_slow: 31 bytes, 11 callsites
radeon_pll_errata_after_data_slow: 91 bytes, 9 callsites
radeon_pll_errata_after_FOO functions are split into two parts:
the inlined part which checks corresponding rinfo->errata bit,
and out-of-line part which performs workaround magic per se.
Reduction in code size is about 49,500 bytes:
text data bss dec hex filename
85789648 22294616 20627456 128711720 7abfc28 vmlinux.before
85740176 22294680 20627456 128662312 7ab3b28 vmlinux
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver implements pan_display but the corresponding flags are not set.
Add FBINFO_HWACCEL_XPAN and FBINFO_HWACCEL_YPAN to flags to allow HW
accelerated panning (for fast scrolling).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add arch_phys_wc_* calls to allow write-combining using MTRR.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The color order in truecolor modes is wrong. This does not affect console but
is visible e.g. in X11 which has wrong colors.
Swap blue and red colors to fix the problem.
Fixes https://forums.gentoo.org/viewtopic-t-692740-start-0.html
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These chips can be present at least on x86 too - Fire GL2 AGP has GXT6000P but
this driver is currently limited to PPC.
Enable it for all architectures and add chip configuration for little-endian.
Tested on x86 with Fire GL2 AGP.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DDC support for Trident cards.
Tested on TGUI9440, TGUI9680, 3DImage 9750, Blade3D 9880 and Blade XP.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
i2c-algo-bit allows I2C adapters without SCL read capability to work
but fb_ddc_read fails to work on them.
Fix fb_ddc_read to work with I2C adapters not capable of reading SCL.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have requested the firmware and it was loaded but we missed releasing
it both on success and error.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This change is needed to properly lock I2C bus driver, which serves DDC.
Prior to this change i2c_put_adapter() is misused, which may lead to
an overflow over zero of I2C bus driver user counter.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
According to X.Org driver, chips older than TGUI9660 have only 1 width bit
in AddColReg. Touching the 2nd one causes I2C/DDC to fail on TGUI9440.
Set only 1 bit of width in AddColReg on TGUI9440 and CYBER9320.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the kernel is compiled with -Os (CONFIG_CC_OPTIMIZE_FOR_SIZE), tridentfb
hangs the machine upon load with Blade3D cards unless acceleration is disabled.
This is caused by memcpy() which copies data byte-by-byte (rep movsb) when
compiled with -Os. The card does not like that - it requires 32-bit access.
Use iowrite_32() instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The ssd1307fb driver supports a lot of chips from the ssd130xfb series.
This patch adds the ssd1309 chip, a 128x64 OLED driver chip. It is very
similar to the other chips and only has some definitions added to
support it.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch sorts the headers on ssd1307fb driver.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regno is unsigned so it cannot be negative.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reconfigure and restart audio when display is enabled, if audio
playback was active before. This is needed in a situation when an
audio+video stream application opens the audio stream before the
video. When video stream is opened the display mode may change and
that aborts audio playback, because the display is momentarily
turned off.
The audio configuration is stored when it is successfully applied and
a boolean is set when the audio playback is started and unset when
stopped. This data is used to reconfigure the audio when display is
re-enabled. The audio playback is aborted if the reconfiguration fails.
A new spin lock is introduced in order to protect state variables
related to audio playback status. This is needed for the transition
from display enabled state (when audio start/stop commands can be
written to HW) to display disabled state (when audio start/stop
commands update only the hdmi.audio_playing variable) to always
serialize correctly with the start/stop audio commands. The already
existing mutex can not be used, because the audio start and stop
commands are executed in atomic context.
For example: when display is turned back on we take the spinlock and
we can be sure that the audio start/stop status will not change while
we update the HW according to hdmi.audio_playing state and set
hdmi.display_enabled to true. After releasing the lock
hdmi.display_enabled is true and all audio_start and audio_stop
commands write their stuff directly to HW.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For deep sleep, the diu module will power off, when wake up
from the deep sleep, the registers need to be reinitialized.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge third patch-bomb from Andrew Morton:
- even more of the rest of MM
- lib/ updates
- checkpatch updates
- small changes to a few scruffy filesystems
- kmod fixes/cleanups
- kexec updates
- a dma-mapping cleanup series from hch
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
dma-mapping: consolidate dma_set_mask
dma-mapping: consolidate dma_supported
dma-mapping: cosolidate dma_mapping_error
dma-mapping: consolidate dma_{alloc,free}_noncoherent
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
mm: make sure all file VMAs have ->vm_ops set
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
mm: mark most vm_operations_struct const
namei: fix warning while make xmldocs caused by namei.c
ipc: convert invalid scenarios to use WARN_ON
zlib_deflate/deftree: remove bi_reverse()
lib/decompress_unlzma: Do a NULL check for pointer
lib/decompressors: use real out buf size for gunzip with kernel
fs/affs: make root lookup from blkdev logical size
sysctl: fix int -> unsigned long assignments in INT_MIN case
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
kexec: align crash_notes allocation to make it be inside one physical page
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
kexec: split kexec_load syscall from kexec core code
...
- Use the correct GFN/BFN terms more consistently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV8VRMAAoJEFxbo/MsZsTRiGQH/i/jrAJUJfrFC2PINaA2gDwe
O0dlrkCiSgAYChGmxxxXZQSPM5Po5+EbT/dLjZ/uvSooeorM9RYY/mFo7ut/qLep
4pyQUuwGtebWGBZTrj9sygUVXVhgJnyoZxskNUbhj9zvP7hb9++IiI78mzne6cpj
lCh/7Z2dgpfRcKlNRu+qpzP79Uc7OqIfDK+IZLrQKlXa7IQDJTQYoRjbKpfCtmMV
BEG3kN9ESx5tLzYiAfxvaxVXl9WQFEoktqe9V8IgOQlVRLgJ2DQWS6vmraGrokWM
3HDOCHtRCXlPhu1Vnrp0R9OgqWbz8FJnmVAndXT8r3Nsjjmd0aLwhJx7YAReO/4=
=JDia
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen terminology fixes from David Vrabel:
"Use the correct GFN/BFN terms more consistently"
* tag 'for-linus-4.3-rc0b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: Rename the variable xen_store_mfn to xen_store_gfn
xen/privcmd: Further s/MFN/GFN/ clean-up
hvc/xen: Further s/MFN/GFN clean-up
video/xen-fbfront: Further s/MFN/GFN clean-up
xen/tmem: Use xen_page_to_gfn rather than pfn_to_gfn
xen: Use correctly the Xen memory terminologies
arm/xen: implement correctly pfn_to_mfn
xen: Make clear that swiotlb and biomerge are dealing with DMA address
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
