Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
If an irq chip does not implement the irq_disable callback, then we
use a lazy approach for disabling the interrupt. That means that the
interrupt is marked disabled, but the interrupt line is not
immediately masked in the interrupt chip. It only becomes masked if
the interrupt is raised while it's marked disabled. We use this to avoid
possibly expensive mask/unmask operations for common case operations.
Unfortunately there are devices which do not allow the interrupt to be
disabled easily at the device level. They are forced to use
disable_irq_nosync(). This can result in taking each interrupt twice.
Instead of enforcing the non lazy mode on all interrupts of a irq
chip, provide a settings flag, which can be set by the driver for that
particular interrupt line.
Reported-and-tested-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1510092348370.6097@nanos
Some drivers might use the per-cpu interrupts and still might be built as a
module. Export request_percpu_irq an free_percpu_irq to these user, which
also make it consistent with enable/disable_percpu_irq that were exported.
Reported-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation of request_percpu_irq is confusing and suggest that the
interrupt is not enabled at all, while it is actually enabled on the local
CPU.
Clarify that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force threading of interrupts does not really deal with interrupts
which are requested with a primary and a threaded handler. The current
policy is to leave them alone and let the primary handler run in
interrupt context, but we set the ONESHOT flag for those interrupts as
well.
Kohji Okuno debugged a problem with the SDHCI driver where the
interrupt thread waits for a hardware interrupt to trigger, which can't
work well because the hardware interrupt is masked due to the ONESHOT
flag being set. He proposed to set the ONESHOT flag only if the
interrupt does not provide a thread handler.
Though that does not work either because these interrupts can be
shared. So the other interrupt would rightfully get the ONESHOT flag
set and therefor the same situation would happen again.
To deal with this proper, we need to force thread the primary handler
of such interrupts as well. That means that the primary interrupt
handler is treated as any other primary interrupt handler which is not
marked IRQF_NO_THREAD. The threaded handler becomes a separate thread
so the SDHCI flow logic can be handled gracefully.
The same issue was reported against 4.1-rt.
Reported-and-tested-by: Kohji Okuno <okuno.kohji@jp.panasonic.com>
Reported-By: Michal Smucr <msmucr@gmail.com>
Reported-and-tested-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1509211058080.5606@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Irq affinity mask is per-irq instead of per irqchip, so move it into
struct irq_common_data.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1433303281-27688-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export these functions to be able to build the Qualcomm family A PMIC
gpio and mpp drivers as modules.
[ tglx: Made them GPL exports ]
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: <kernel-build-reports@lists.linaro.org>
Cc: <linaro-kernel@lists.linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1437594184-22966-1-git-send-email-bjorn.andersson@sonymobile.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unused except for the alpha wrapper, which can retrieve if from the
irq descriptor.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1433391238-19471-21-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide a irq_desc based variant of irq_can_set_affinity() to avoid a
redundant lookup for the core code users.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Solely used for debug output. Can be retrieved from irq descriptor if
necessary.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's only required for debug output and can be retrieved from the irq
descriptor if necessary.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's only used in the software resend case and can be retrieved from
irq_desc if necessary.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1433391238-19471-18-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce helper function irq_data_get_node() and variants thereof to
hide struct irq_data implementation details.
Convert the core code to use them.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1433145945-789-5-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With Posted-Interrupts support in Intel CPU and IOMMU, an external
interrupt from assigned-devices could be directly delivered to a
virtual CPU in a virtual machine. Instead of hacking KVM and Intel
IOMMU drivers, we propose a platform independent interface to target
an interrupt to a specific virtual CPU in a virtual machine, or set
virtual CPU affinity for an interrupt.
By adopting this new interface and the hierarchy irqdomain, we could
easily support posted-interrupts on Intel platforms, and also provide
flexible enough interfaces for other platforms to support similar
features.
Here is the usage scenario for this interface:
Guest update MSI/MSI-X interrupt configuration
-->QEMU and KVM handle this
-->KVM call this interface (passing posted interrupts descriptor
and guest vector)
-->irq core will transfer the control to IOMMU
-->IOMMU will do the real work of updating IRTE (IRTE has new
format for VT-d Posted-Interrupts)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Link: http://lkml.kernel.org/r/1432026437-16560-2-git-send-email-feng.wu@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is a number of cases where a kernel subsystem may want to
introspect the state of an interrupt at the irqchip level:
- When a peripheral is shared between virtual machines,
its interrupt state becomes part of the guest's state,
and must be switched accordingly. KVM on arm/arm64 requires
this for its guest-visible timer
- Some GPIO controllers seem to require peeking into the
interrupt controller they are connected to to report
their internal state
This seem to be a pattern that is common enough for the core code
to try and support this without too many horrible hacks. Introduce
a pair of accessors (irq_get_irqchip_state/irq_set_irqchip_state)
to retrieve the bits that can be of interest to another subsystem:
pending, active, and masked.
- irq_get_irqchip_state returns the state of the interrupt according
to a parameter set to IRQCHIP_STATE_PENDING, IRQCHIP_STATE_ACTIVE,
IRQCHIP_STATE_MASKED or IRQCHIP_STATE_LINE_LEVEL.
- irq_set_irqchip_state similarly sets the state of the interrupt.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tin Huynh <tnhuynh@apm.com>
Cc: Y Vo <yvo@apm.com>
Cc: Toan Le <toanle@apm.com>
Cc: Bjorn Andersson <bjorn@kryo.se>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1426676484-21812-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It currently is required that all users of NO_SUSPEND interrupt
lines pass the IRQF_NO_SUSPEND flag when requesting the IRQ or the
WARN_ON_ONCE() in irq_pm_install_action() will trigger. That is
done to warn about situations in which unprepared interrupt handlers
may be run unnecessarily for suspended devices and may attempt to
access those devices by mistake. However, it may cause drivers
that have no technical reasons for using IRQF_NO_SUSPEND to set
that flag just because they happen to share the interrupt line
with something like a timer.
Moreover, the generic handling of wakeup interrupts introduced by
commit 9ce7a25849 (genirq: Simplify wakeup mechanism) only works
for IRQs without any NO_SUSPEND users, so the drivers of wakeup
devices needing to use shared NO_SUSPEND interrupt lines for
signaling system wakeup generally have to detect wakeup in their
interrupt handlers. Thus if they happen to share an interrupt line
with a NO_SUSPEND user, they also need to request that their
interrupt handlers be run after suspend_device_irqs().
In both cases the reason for using IRQF_NO_SUSPEND is not because
the driver in question has a genuine need to run its interrupt
handler after suspend_device_irqs(), but because it happens to
share the line with some other NO_SUSPEND user. Otherwise, the
driver would do without IRQF_NO_SUSPEND just fine.
To make it possible to specify that condition explicitly, introduce
a new IRQ action handler flag for shared IRQs, IRQF_COND_SUSPEND,
that, when set, will indicate to the IRQ core that the interrupt
user is generally fine with suspending the IRQ, but it also can
tolerate handler invocations after suspend_device_irqs() and, in
particular, it is capable of detecting system wakeup and triggering
it as appropriate from its interrupt handler.
That will allow us to work around a problem with a shared timer
interrupt line on at91 platforms.
Link: http://marc.info/?l=linux-kernel&m=142252777602084&w=2
Link: http://marc.info/?t=142252775300011&r=1&w=2
Link: https://lkml.org/lkml/2014/12/15/552
Reported-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
For things like netpoll there is a need to disable an interrupt from
atomic context. Currently netpoll uses disable_irq() which will
sleep-wait on threaded handlers and thus forced_irqthreads breaks
things.
Provide disable_hardirq(), which uses synchronize_hardirq() to only wait
for active hardirq handlers; also change synchronize_hardirq() to
return the status of threaded handlers.
This will allow one to try-disable an interrupt from atomic context, or
in case of request_threaded_irq() to only wait for the hardirq part.
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Miller <davem@davemloft.net>
Cc: Eyal Perry <eyalpe@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20150205130623.GH5029@twins.programming.kicks-ass.net
[ Fixed typos and such. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The recent set_affinity commit by me introduced some null
pointer dereferences on driver unload, because some drivers
call this function with a NULL argument. This fixes the issue
by just checking for null before setting the affinity mask.
Fixes: e2e64a9325 ("genirq: Set initial affinity in irq_set_affinity_hint()")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20150128185739.9689.84588.stgit@jbrandeb-cp2.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Problem:
The default behavior of the kernel is somewhat undesirable as all
requested interrupts end up on CPU0 after registration. A user can
run irqbalance daemon, or can manually configure smp_affinity via the
proc filesystem, but the default affinity of the interrupts for all
devices is always CPU zero, this can cause performance problems or
very heavy cpu use of only one core if not noticed and fixed by the
user.
Solution:
Enable the setting of the initial affinity directly when the driver
sets a hint.
This enabling means that kernel drivers can include an initial
affinity setting for the interrupt, instead of all interrupts starting
out life on CPU0. Of course if irqbalance is still running then the
interrupts will get moved as before.
This function is currently called by drivers in block, crypto,
infiniband, ethernet and scsi trees, but only a handful, so these will
be the devices affected by this change.
Tested on i40e, and default interrupts were spread across the CPUs
according to the hint.
drivers/block/mtip32xx/mtip32xx.c:3
drivers/block/nvme-core.c:2
drivers/crypto/qat/qat_dh895xcc/adf_isr.c:3
drivers/infiniband/hw/qib/qib_iba7322.c:2
drivers/net/ethernet/intel/i40e/i40e_main.c:3
drivers/net/ethernet/intel/i40evf/i40evf_main.c:3
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3
drivers/net/ethernet/mellanox/mlx4/en_cq.c:2
drivers/scsi/hpsa.c:3
drivers/scsi/lpfc/lpfc_init.c:3
drivers/scsi/megaraid/megaraid_sas_base.c:8
drivers/soc/ti/knav_qmss_acc.c:1
drivers/soc/ti/knav_qmss_queue.c:2
drivers/virtio/virtio_pci_common.c:2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20141219012206.4220.27491.stgit@jbrandeb-cp2.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add IRQ_SET_MASK_OK_DONE in addition to IRQ_SET_MASK_OK and
IRQ_SET_MASK_OK_NOCOPY to support stacked irqchip. IRQ_SET_MASK_OK_DONE
is the same as IRQ_SET_MASK_OK to irq core. To stacked irqchip, it means
that ascendant irqchips have done all the work and no more handling
needed in descendant irqchips.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Account the IRQF_NO_SUSPEND and IRQF_RESUME_EARLY actions on shared
interrupt lines and yell loudly if there is a mismatch.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No functional change. Preparatory patch for cleaning up the suspend
abort functionality. Update the comments while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Till reported that the spurious interrupt detection of threaded
interrupts is broken in two ways:
- note_interrupt() is called for each action thread of a shared
interrupt line. That's wrong as we are only interested whether none
of the device drivers felt responsible for the interrupt, but by
calling multiple times for a single interrupt line we account
IRQ_NONE even if one of the drivers felt responsible.
- note_interrupt() when called from the thread handler is not
serialized. That leaves the members of irq_desc which are used for
the spurious detection unprotected.
To solve this we need to defer the spurious detection of a threaded
interrupt to the next hardware interrupt context where we have
implicit serialization.
If note_interrupt is called with action_ret == IRQ_WAKE_THREAD, we
check whether the previous interrupt requested a deferred check. If
not, we request a deferred check for the next hardware interrupt and
return.
If set, we check whether one of the interrupt threads signaled
success. Depending on this information we feed the result into the
spurious detector.
If one primary handler of a shared interrupt returns IRQ_HANDLED we
disable the deferred check of irq threads on the same line, as we have
found at least one device driver who cared.
Reported-by: Till Straumann <strauman@slac.stanford.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1303071450130.22263@ionos
The current implementation of irq_set_affinity() refuses rightfully to
route an interrupt to an offline cpu.
But there is a special case, where this is actually desired. Some of
the ARM SoCs have per cpu timers which require setting the affinity
during cpu startup where the cpu is not yet in the online mask.
If we can't do that, then the local timer interrupt for the about to
become online cpu is routed to some random online cpu.
The developers of the affected machines tried to work around that
issue, but that results in a massive mess in that timer code.
We have a yet unused argument in the set_affinity callbacks of the irq
chips, which I added back then for a similar reason. It was never
required so it got not used. But I'm happy that I never removed it.
That allows us to implement a sane handling of the above scenario. So
the affected SoC drivers can add the required force handling to their
interrupt chip, switch the timer code to irq_force_affinity() and
things just work.
This does not affect any existing user of irq_set_affinity().
Tagged for stable to allow a simple fix of the affected SoC clock
event drivers.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>,
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>,
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20140416143315.717251504@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The flag is necessary for interrupt chips which require an ACK/EOI
after the handler has run. In case of threaded handlers this needs to
happen after the threaded handler has completed before the unmask of
the interrupt.
The flag is only unseful in combination with the handle_fasteoi_irq
flow control handler.
It can be combined with the flag IRQCHIP_EOI_IF_HANDLED, so the EOI is
not issued when the interrupt is disabled or in progress.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1394733834-26839-2-git-send-email-hdegoede@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For certain irq types, e.g. gpios, it's necessary to request resources
before starting up the irq.
This might fail so we cannot use the irq_startup() callback because we
might call the irq_set_type() callback before that which does not make
sense when the resource is not available. Calling irq_startup() before
irq_set_type() can lead to spurious interrupts which is not desired
either.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1403080857160.18573@ionos.tec.linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We hit one rare case below:
T1 calling disable_irq(), but hanging at synchronize_irq()
always;
The corresponding irq thread is in sleeping state;
And all CPUs are in idle state;
After analysis, we found there is one possible scenerio which
causes T1 is waiting there forever:
CPU0 CPU1
synchronize_irq()
wait_event()
spin_lock()
atomic_dec_and_test(&threads_active)
insert the __wait into queue
spin_unlock()
if(waitqueue_active)
atomic_read(&threads_active)
wake_up()
Here after inserted the __wait into queue on CPU0, and before
test if queue is empty on CPU1, there is no barrier, it maybe
cause it is not visible for CPU1 immediately, although CPU0 has
updated the queue list.
It is similar for CPU0 atomic_read() threads_active also.
So we'd need one smp_mb() before waitqueue_active.that, but removing
the waitqueue_active() check solves it as wel l and it makes
things simple and clear.
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Xiaoming Wang <xiaoming.wang@intel.com>
Link: http://lkml.kernel.org/r/1393212590-32543-1-git-send-email-chuansheng.liu@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In course of the sdhci/sdio discussion with Russell about killing the
sdio kthread hackery we discovered the need to be able to wake an
interrupt thread from software.
The rationale for this is, that sdio hardware can lack proper
interrupt support for certain features. So the driver needs to poll
the status registers, but at the same time it needs to be woken up by
an hardware interrupt.
To be able to get rid of the home brewn kthread construct of sdio we
need a way to wake an irq thread independent of an actual hardware
interrupt.
Provide an irq_wake_thread() function which wakes up the thread which
is associated to a given dev_id. This allows sdio to invoke the irq
thread from the hardware irq handler via the IRQ_WAKE_THREAD return
value and provides a possibility to wake it via a timer for the
polling scenarios. That allows to simplify the sdio logic
significantly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Chris Ball <chris@printf.net>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140215003823.772565780@linutronix.de
synchronize_irq() waits for hard irq and threaded handlers to complete
before returning. For some special cases we only need to make sure
that the hard interrupt part of the irq line is not in progress when
we disabled the - possibly shared - interrupt at the device level.
A proper use case for this was provided by Russell. The sdhci driver
requires some irq triggered functions to be run in thread context. The
current implementation of the thread context is a sdio private kthread
construct, which has quite some shortcomings. These can be avoided
when the thread is directly associated to the device interrupt via the
generic threaded irq infrastructure.
Though there is a corner case related to run time power management
where one side disables the device interrupts at the device level and
needs to make sure, that an already running hard interrupt handler has
completed before proceeding further. Though that hard interrupt
handler might wake the associated thread, which in turn can request
the runtime PM to reenable the device. Using synchronize_irq() leads
to an immediate deadlock of the irq thread waiting for the PM lock and
the synchronize_irq() waiting for the irq thread to complete.
Due to the fact that it is sufficient for this case to ensure that no
hard irq handler is executing a new function which avoids the check
for the thread is required.
Add a function, which just monitors the hard irq parts and ignores the
threaded handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <linux@arm.linux.org.uk>
Cc: Chris Ball <chris@printf.net>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140215003823.653236081@linutronix.de
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
In commit ee23871389 ("genirq: Set irq thread to RT priority on
creation") we moved the assigment of the thread's priority from the
thread's function into __setup_irq(). That function may run in user
context for instance if the user opens an UART node and then driver
calls requests in the ->open() callback. That user may not have
CAP_SYS_NICE and so the irq thread won't run with the SCHED_OTHER
policy.
This patch uses sched_setscheduler_nocheck() so we omit the CAP_SYS_NICE
check which is otherwise required for the SCHED_OTHER policy.
[bigeasy: Rewrite the changelog]
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Cc: Ivo Sieben <meltedpianoman@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1381489240-29626-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 02725e7471 ('genirq: Use irq_get/put functions'),
inadvertently changed can_request_irq() to return 0 for IRQs that have
no action. This causes pcibios_lookup_irq() to select only IRQs that
already have an action with IRQF_SHARED set, or to fail if there are
none. Change can_request_irq() to return 1 for IRQs that have no
action (if the first two conditions are met).
Reported-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Tested-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is> (against 3.2)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: 709647@bugs.debian.org
Cc: stable@vger.kernel.org # 2.6.39+
Link: http://bugs.debian.org/709647
Link: http://lkml.kernel.org/r/1372383630.23847.40.camel@deadeye.wl.decadent.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When a threaded irq handler is installed the irq thread is initially
created on normal scheduling priority. Only after the irq thread is
woken up it sets its priority to RT_FIFO MAX_USER_RT_PRIO/2 itself.
This means that interrupts that occur directly after the irq handler
is installed will be handled on a normal scheduling priority instead
of the realtime priority that one would expect.
Fix this by setting the RT priority on creation of the irq_thread.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1370254322-17240-1-git-send-email-meltedpianoman@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull scheduler changes from Ingo Molnar:
"Main changes:
- scheduler side full-dynticks (user-space execution is undisturbed
and receives no timer IRQs) preparation changes that convert the
cputime accounting code to be full-dynticks ready, from Frederic
Weisbecker.
- Initial sched.h split-up changes, by Clark Williams
- select_idle_sibling() performance improvement by Mike Galbraith:
" 1 tbench pair (worst case) in a 10 core + SMT package:
pre 15.22 MB/sec 1 procs
post 252.01 MB/sec 1 procs "
- sched_rr_get_interval() ABI fix/change. We think this detail is not
used by apps (so it's not an ABI in practice), but lets keep it
under observation.
- misc RT scheduling cleanups, optimizations"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched/rt: Add <linux/sched/rt.h> header to <linux/init_task.h>
cputime: Remove irqsave from seqlock readers
sched, powerpc: Fix sched.h split-up build failure
cputime: Restore CPU_ACCOUNTING config defaults for PPC64
sched/rt: Move rt specific bits into new header file
sched/rt: Add a tuning knob to allow changing SCHED_RR timeslice
sched: Move sched.h sysctl bits into separate header
sched: Fix signedness bug in yield_to()
sched: Fix select_idle_sibling() bouncing cow syndrome
sched/rt: Further simplify pick_rt_task()
sched/rt: Do not account zero delta_exec in update_curr_rt()
cputime: Safely read cputime of full dynticks CPUs
kvm: Prepare to add generic guest entry/exit callbacks
cputime: Use accessors to read task cputime stats
cputime: Allow dynamic switch between tick/virtual based cputime accounting
cputime: Generic on-demand virtual cputime accounting
cputime: Move default nsecs_to_cputime() to jiffies based cputime file
cputime: Librarize per nsecs resolution cputime definitions
cputime: Avoid multiplication overflow on utime scaling
context_tracking: Export context state for generic vtime
...
Fix up conflict in kernel/context_tracking.c due to comment additions.
Move rt scheduler definitions out of include/linux/sched.h into
new file include/linux/sched/rt.h
Signed-off-by: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20130207094707.7b9f825f@riff.lan
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The array check is useless so remove it.
[akpm@linux-foundation.org: remove comment, per David]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sankara reported that the genirq core code fails to adjust the
affinity of an interrupt thread in several cases:
1) On request/setup_irq() the call to setup_affinity() happens before
the new action is registered, so the new thread is not notified.
2) For secondary shared interrupts nothing notifies the new thread to
change its affinity.
3) Interrupts which have the IRQ_NO_BALANCE flag set are not moving
the thread either.
Fix this by setting the thread affinity flag right on thread creation
time. This ensures that under all circumstances the thread moves to
the right place. Requires a check in irq_thread_check_affinity for an
existing affinity mask (CONFIG_CPU_MASK_OFFSTACK=y)
Reported-and-tested-by: Sankara Muthukrishnan <sankara.m@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1209041738200.2754@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As irq_thread_check_affinity is called ONLY inside the while loop in
the irq thread, the core affinity is set only when an interrupt
occurs. This patch sets the core affinity right after the irq thread
is created and before it waits for interrupts. In real-tiime targets
that do not typically change the core affinity of irqs during
run-time, this patch will save additional latency of an irq thread in
setting the core affinity during the first interrupt occurrence for
that irq.
Signed-off-by: Sankara S Muthukrishnan <sankara.m@ni.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/CAFQPvXeVZ858WFYimEU5uvLNxLDd6bJMmqWihFmbCf3ntokz0A@mail.gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Attempts to retrigger nested threaded IRQs currently fail because they
have no primary handler. In order to support retrigger of nested
IRQs, the parent IRQ needs to be retriggered.
To fix, when an IRQ needs to be resent, if the interrupt has a parent
IRQ and runs in the context of the parent IRQ, then resend the parent.
Also, handle_nested_irq() needs to clear the replay flag like the
other handlers, otherwise check_irq_resend() will set it and it will
never be cleared. Without clearing, it results in the first resend
working fine, but check_irq_resend() returning early on subsequent
resends because the replay flag is still set.
Problem discovered on ARM/OMAP platforms where a nested IRQ that's
also a wakeup IRQ happens late in suspend and needed to be retriggered
during the resume process.
[khilman@ti.com: changelog edits, clear IRQS_REPLAY in handle_nested_irq()]
Reported-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1350425269-11489-1-git-send-email-khilman@deeprootsystems.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull irq fix from Ingo Molnar.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Allow irq chips to mark themself oneshot safe
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Some interrupt chips like MSI are oneshot safe by implementation. For
those interrupts we can avoid the mask/unmask sequence for threaded
interrupt handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1207132056540.32033@ionos
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Jan Kiszka <jan.kiszka@web.de>
task_work and rcu_head are identical now; merge them (calling the result
struct callback_head, rcu_head #define'd to it), kill separate allocation
in security/keys since we can just use cred->rcu now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
get rid of the only user of ->data; this is _not_ the final variant - in the
end we'll have task_work and rcu_head identical and just use cred->rcu,
at which point the separate allocation will be gone completely.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
