enet_clk_ref actually is sourced from internal gpr clocks
which needs a default rate. Also update enet lpcg clock
output names to be more straightforward.
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DMA addressing capabilities on i.MX8MN are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DMA addressing capabilities on i.MX8MM are limited by the interconnect,
same as on i.MX8MQ. Add dma-ranges to the the peripheral bus to let
the kernel know about this.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently all PCIE windows point to bus address 0x0, which does not match
the values obtained from hardware during EA.
Replace those values with CPU addresses, since in reality we
have a 1:1 mapping between the two.
Signed-off-by: Kornel Duleba <mindal@semihalf.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c3 ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1012a-freeway board contains a M.2 2230 slot. Update the status of
pcei1 node to okay so that the pcie controller can be probed.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX8MP, there is no audio ipg clock, so remove the wrong reference
to this clock in dts file.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MM reference manual shows there are two spba busses.
SPBA1 handles much of the serial interfaces, and SPBA2 covers much
of the audio.
Add both of them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MN has an SPBA bus which covers much of the audio, but
there is a second SPBA bus which covers many of the serial interfaces
like SPI and UARTs currently missing from the device tree. The reference
manual calls the bus handling the audio peripherals SPBA2, and the bus
handling the serial peripherals is called SPBA1.
Rename the existing spba bus to spba2 and add spba1.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support of the lt8912b in the DTB.
This adds the support of the DB_DSIHD daugther board from
Boundary Devices.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the description for the USB host port.
This port is linked to a resettable USB HUB so handle
this reset signal with a GPIO hog.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the description for the USB OTG port.
The OTG port uses a dedicated regulator for vbus.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PCIe host bridge on RK3399 advertises a single 64-bit memory
address range even though it lies entirely below 4GB.
Previously the OF PCI range parser treated 64-bit ranges more
leniently (i.e., as 32-bit), but since commit 9d57e61bf7 ("of/pci:
Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")
the code takes a stricter view and treats the ranges as advertised in
the device tree (i.e, as 64-bit).
The change in behaviour causes failure when allocating bus addresses
to devices connected behind a PCI-to-PCI bridge that require
non-prefetchable memory ranges. The allocation failure was observed
for certain Samsung NVMe drives connected to RockPro64 boards.
Update the host bridge window attributes to treat it as 32-bit address
memory. This fixes the allocation failure observed since commit
9d57e61bf7.
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/7a1e2ebc-f7d8-8431-d844-41a9c36a8911@arm.com
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20210607112856.3499682-5-punitagrawal@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Host stage-2 optimisations from Quentin Perret
* kvm-arm64/mmu/reduce-vmemmap-overhead:
KVM: arm64: Use less bits for hyp_page refcount
KVM: arm64: Use less bits for hyp_page order
KVM: arm64: Remove hyp_pool pointer from struct hyp_page
KVM: arm64: Unify MMIO and mem host stage-2 pools
KVM: arm64: Remove list_head from hyp_page
KVM: arm64: Use refcount at hyp to check page availability
KVM: arm64: Move hyp_pool locking out of refcount helpers
Scheduling a 32-bit application on a 64-bit-only CPU is a bad idea.
Ensure that 32-bit applications always take the slow-path when returning
to userspace on a system with mismatched support at EL0, so that we can
avoid trying to run on a 64-bit-only CPU and force a SIGKILL instead.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-5-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
When confronted with a mixture of CPUs, some of which support 32-bit
applications and others which don't, we quite sensibly treat the system
as 64-bit only for userspace and prevent execve() of 32-bit binaries.
Unfortunately, some crazy folks have decided to build systems like this
with the intention of running 32-bit applications, so relax our
sanitisation logic to continue to advertise 32-bit support to userspace
on these systems and track the real 32-bit capable cores in a cpumask
instead. For now, the default behaviour remains but will be tied to
a command-line option in a later patch.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210608180313.11502-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The hyp_page refcount is currently encoded on 4 bytes even though we
never need to count that many objects in a page. Make it 2 bytes to save
some space in the vmemmap.
As overflows are more likely to happen as well, make sure to catch those
with a BUG in the increment function.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-8-qperret@google.com
Each struct hyp_page currently contains a pointer to a hyp_pool struct
where the page should be freed if its refcount reaches 0. However, this
information can always be inferred from the context in the EL2 code, so
drop the pointer to save a few bytes in the vmemmap.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-6-qperret@google.com
We currently maintain two separate memory pools for the host stage-2,
one for pages used in the page-table when mapping memory regions, and
the other to map MMIO regions. The former is large enough to map all of
memory with page granularity and the latter can cover an arbitrary
portion of IPA space, but allows to 'recycle' pages.
However, this split makes accounting difficult to manage as pages at
intermediate levels of the page-table may be used to map both memory and
MMIO regions. Simplify the scheme by merging both pools into one. This
means we can now hit the -ENOMEM case in the memory abort path, but
we're still guaranteed forward-progress in the worst case by unmapping
MMIO regions. On the plus side this also means we can usually map a lot
more MMIO space at once if memory ranges happen to be mapped with block
mappings.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-5-qperret@google.com
The list_head member of struct hyp_page is only needed when the page is
attached to a free-list, which by definition implies the page is free.
As such, nothing prevents us from using the page itself to store the
list_head, hence reducing the size of the vmemmap.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-4-qperret@google.com
The hyp buddy allocator currently checks the struct hyp_page list node
to see if a page is available for allocation or not when trying to
coalesce memory. Now that decrementing the refcount and attaching to
the buddy tree is done in the same critical section, we can rely on the
refcount of the buddy page to be in sync, which allows to replace the
list node check by a refcount check. This will ease removing the list
node from struct hyp_page later on.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-3-qperret@google.com
The hyp_page refcount helpers currently rely on the hyp_pool lock for
serialization. However, this means the refcounts can't be changed from
the buddy allocator core as it already holds the lock, which means pages
have to go through odd transient states.
For example, when a page is freed, its refcount is set to 0, and the
lock is transiently released before the page can be attached to a free
list in the buddy tree. This is currently harmless as the allocator
checks the list node of each page to see if it is available for
allocation or not, but it means the page refcount can't be trusted to
represent the state of the page even if the pool lock is held.
In order to fix this, remove the pool locking from the refcount helpers,
and move all the logic to the buddy allocator. This will simplify the
removal of the list node from struct hyp_page in a later patch.
Signed-off-by: Quentin Perret <qperret@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210608114518.748712-2-qperret@google.com
Add the device tree node for the dual-SMMU found on Tegra194 and hook up
peripherals such as host1x, BPMP, HDA, SDMMC, EQOS and VIC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra186 and later, the memory controller needs to be programmed in
coordination with any of the ARM SMMU instances to configure the stream
ID used for each memory client.
To support this, add a phandle reference to the memory controller to the
SMMU device tree node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SMMU found on Tegra186 requires interoperation with the memory
controller in order to program stream ID overrides. The generic ARM SMMU
500 compatible is therefore inaccurate. Replace it with a more correct,
SoC-specific compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, <asm/insn.h> includes <asm/patching.h>. We intend that
<asm/insn.h> will be usable from userspace, so it doesn't make sense to
include headers for kernel-only features such as the patching routines,
and we'd intended to restrict <asm/insn.h> to instruction encoding
details.
Let's decouple the patching code from <asm/insn.h>, and explicitly
include <asm/patching.h> where it is needed. Since <asm/patching.h>
isn't included from assembly, we can drop the __ASSEMBLY__ guards.
At the same time, sort the kprobes includes so that it's easier to see
what is and isn't incldued.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210609102301.17332-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
The Huawei Ascend G7 supports NFC using the NXP PN547, which is
supported by the nxp-nci-i2c driver in mainline. It seems to detect
NFC tags using "nfctool" just fine, although it seems like there
are not really any useful applications making use of the Linux NFC
subsystem. :(
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Huawei Ascend G7 is a smartphone from Huawei based on MSM8916.
It's fairly similar to the other MSM8916 devices, the only notable
exception are the "cd-gpios" for detecting if a SD card was inserted:
It looks like Huawei forgot to re-route this to gpio38, so the correct
GPIO seems to be gpio56 on this device.
Note: The original firmware from Huawei can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei
forgot to set up (firmware) secure boot for some reason.
Also note that Huawei no longer provides bootloader unlock codes.
This can be bypassed by patching the bootloader from a custom HYP firmware,
making it think the bootloader is unlocked. I use a modified version of
qhypstub [1], that patches a single instruction in the Huawei bootloader.
The device tree contains initial support for the Huawei Ascend G7 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Notification LED (combination of 3 GPIO LEDs)
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
[1]: https://github.com/msm8916-mainline/qhypstub
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210514104328.18756-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On coachz it could be observed that SPI_CLK voltage level was only
1.4V during active transfers because the drive strength was too
weak. The line hadn't finished slewing up by the time we started
driving it down again. Using a drive strength of 8 lets us achieve the
correct voltage level of 1.8V.
Though the worst problems were observed on coachz hardware, let's do
this across the board for trogdor devices. Scoping other boards shows
that this makes the clk line look nicer on them too and doesn't
introduce any problems.
Only the clk line is adjusted, not any data lines. Because SPI isn't a
DDR protocol we only sample the data lines on either rising or falling
edges, not both. That means the clk line needs to toggle twice as fast
as data lines so having the higher drive strength is more important
there.
Signed-off-by: Wenchao Han <hanwenchao@huaqin.corp-partner.google.com>
[dianders: Adjust author real name; adjust commit message]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210510075253.1.Ib4c296d6ff9819f26bcaf91e8a08729cc203fed0@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
