Normal PCI PEs have 2 TVEs, one per a DMA window; however NPU PE has only
one which points to one of two tables of the corresponding PCI PE.
So whenever a new DMA window is programmed to PEs, the NPU PE needs to
release old table in order to use the new one.
Commit d41ce7b1bc ("powerpc/powernv/npu: Do not try invalidating 32bit
table when 64bit table is enabled") did just that but in pci-ioda.c
while it actually belongs to npu-dma.c.
This moves the single TVE handling to npu-dma.c. This does not implement
restoring though as it is highly unlikely that we can set the table to
PCI PE and cannot to NPU PE and if that fails, we could only set 32bit
table to NPU PE and this configuration is not really supported or wanted.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The iommu_table pointer stored in iommu_table_group may get stale
by accident, this adds referencing and removes a redundant comment
about this.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Registering new IOMMU groups and adding devices to them are separated in
code and the latter is dug in the DMA setup code which it does not
really belong to.
This moved IOMMU groups setup to a separate helper which registers a group
and adds devices as before. This does not make a difference as IOMMU
groups are not used anyway; the only dependency here is that
iommu_add_device() requires a valid pointer to an iommu_table
(set by set_iommu_table_base()).
To keep the old behaviour, this does not add new IOMMU groups for PEs
with no DMA weight and also skips NVLink bridges which do not have
pci_controller_ops::setup_bridge (the normal way of adding PEs).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv platform registers IOMMU groups and adds devices to them
from the pci_controller_ops::setup_bridge() hook except one case when
virtual functions (SRIOV VFs) are added from a bus notifier.
The pseries platform registers IOMMU groups from
the pci_controller_ops::dma_bus_setup() hook and adds devices from
the pci_controller_ops::dma_dev_setup() hook. The very same bus notifier
used for powernv does not add devices for pseries though as
__of_scan_bus() adds devices first, then it does the bus/dev DMA setup.
Both platforms use iommu_add_device() which takes a device and expects
it to have a valid IOMMU table struct with an iommu_table_group pointer
which in turn points the iommu_group struct (which represents
an IOMMU group). Although the helper seems easy to use, it relies on
some pre-existing device configuration and associated data structures
which it does not really need.
This simplifies iommu_add_device() to take the table_group pointer
directly. Pseries already has a table_group pointer handy and the bus
notified is not used anyway. For powernv, this copies the existing bus
notifier, makes it work for powernv only which means an easy way of
getting to the table_group pointer. This was tested on VFs but should
also support physical PCI hotplug.
Since iommu_add_device() receives the table_group pointer directly,
pseries does not do TCE cache invalidation (the hypervisor does) nor
allow multiple groups per a VFIO container (in other words sharing
an IOMMU table between partitionable endpoints), this removes
iommu_table_group_link from pseries.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pci_dma_bus_setup_pSeries and pci_dma_dev_setup_pSeries hooks are
registered for the pseries platform which does not have FW_FEATURE_LPAR;
these would be pre-powernv platforms which we never supported PCI pass
through for anyway so remove it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We already changed NPU API for GPUs to not to call OPAL and the remaining
bit is initializing NPU structures.
This searches for POWER9 NVLinks attached to any device on a PHB and
initializes an NPU structure if any found.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We might have memory@ nodes with "linux,usable-memory" set to zero
(for example, to replicate powernv's behaviour for GPU coherent memory)
which means that the memory needs an extra initialization but since
it can be used afterwards, the pseries platform will try mapping it
for DMA so the DMA window needs to cover those memory regions too;
if the window cannot cover new memory regions, the memory onlining fails.
This walks through the memory nodes to find the highest RAM address to
let a huge DMA window cover that too in case this memory gets onlined
later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When introduced, the NPU context init/destroy helpers called OPAL which
enabled/disabled PID (a userspace memory context ID) filtering in an NPU
per a GPU; this was a requirement for P9 DD1.0. However newer chip
revision added a PID wildcard support so there is no more need to
call OPAL every time a new context is initialized. Also, since the PID
wildcard support was added, skiboot does not clear wildcard entries
in the NPU so these remain in the hardware till the system reboot.
This moves LPID and wildcard programming to the PE setup code which
executes once during the booting process so NPU2 context init/destroy
won't need to do additional configuration.
This replaces the check for FW_FEATURE_OPAL with a check for npu!=NULL as
this is the way to tell if the NPU support is present and configured.
This moves pnv_npu2_init() declaration as pseries should be able to use it.
This keeps pnv_npu2_map_lpar() in powernv as pseries is not allowed to
call that. This exports pnv_npu2_map_lpar_dev() as following patches
will use it from the VFIO driver.
While at it, replace redundant list_for_each_entry_safe() with
a simpler list_for_each_entry().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv PCI code stores NPU data in the pnv_phb struct. The latter
is referenced by pci_controller::private_data. We are going to have NPU2
support in the pseries platform as well but it does not store any
private_data in in the pci_controller struct; and even if it did,
it would be a different data structure.
This makes npu a pointer and stores it one level higher in
the pci_controller struct.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The skiboot firmware has a hot reset handler which fences the NVIDIA V100
GPU RAM on Witherspoons and makes accesses no-op instead of throwing HMIs:
https://github.com/open-power/skiboot/commit/fca2b2b839a67
Now we are going to pass V100 via VFIO which most certainly involves
KVM guests which are often terminated without getting a chance to offline
GPU RAM so we end up with a running machine with misconfigured memory.
Accessing this memory produces hardware management interrupts (HMI)
which bring the host down.
To suppress HMIs, this wires up this hot reset hook to vfio_pci_disable()
via pci_disable_device() which switches NPU2 to a safe mode and prevents
HMIs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
System call table generation script must be run to gener-
ate unistd_32/64.h and syscall_table_32/64/c32/spu.h files.
This patch will have changes which will invokes the script.
This patch will generate unistd_32/64.h and syscall_table-
_32/64/c32/spu.h files by the syscall table generation
script invoked by parisc/Makefile and the generated files
against the removed files must be identical.
The generated uapi header file will be included in uapi/-
asm/unistd.h and generated system call table header file
will be included by kernel/systbl.S file.
Signed-off-by: Firoz Khan <firoz.khan@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For fadump to work successfully there should not be any holes in reserved
memory ranges where kernel has asked firmware to move the content of old
kernel memory in event of crash. Now that fadump uses CMA for reserved
area, this memory area is now not protected from hot-remove operations
unless it is cma allocated. Hence, fadump service can fail to re-register
after the hot-remove operation, if hot-removed memory belongs to fadump
reserved region. To avoid this make sure that memory from fadump reserved
area is not hot-removable if fadump is registered.
However, if user still wants to remove that memory, he can do so by
manually stopping fadump service before hot-remove operation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
opal_power_control_init() depends on opal message notifier to be
initialized, which is done in opal_init()->opal_message_init(). But both
these initialization are called through machine initcalls and it all
depends on in which order they being called. So far these are called in
correct order (may be we got lucky) and never saw any issue. But it is
clearer to control initialization order explicitly by moving
opal_power_control_init() into opal_init().
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Omit an extra message for a memory allocation failure in these
functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some data were printed into a sequence by four separate function calls.
Print the same data by two single function calls instead.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PCI_MSI was made mandatory by commit a311e738b6
("powerpc/powernv: Make PCI non-optional") so the #ifdef
checks around CONFIG_PCI_MSI here can be removed entirely.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current implementation of the OPAL_PCI_EEH_FREEZE_STATUS call in
skiboot's NPU driver does not touch the pci_error_type parameter so
it might have garbage but the powernv code analyzes it nevertheless.
This initializes pcierr and fstate to zero in all call sites.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fixup_phb() is never used, this removes it.
pick_m64_pe() and reserve_m64_pe() are always defined for all powernv
PHBs: they are initialized by pnv_ioda_parse_m64_window() which is
called unconditionally from pnv_pci_init_ioda_phb() which initializes
all known PHB types on powernv so we can open code them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment PNV_IODA_PE_DEV is only used for NPU PEs which are not
present on IODA1 machines (i.e. POWER7) so let's remove a piece of
dead code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The macro and few headers are not used so remove them.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powernv platform maintains 2 TCE tables for VFIO - a hardware TCE
table and a table with userspace addresses; the latter is used for
marking pages dirty when corresponging TCEs are unmapped from
the hardware table.
a68bd1267b ("powerpc/powernv/ioda: Allocate indirect TCE levels
on demand") enabled on-demand allocation of the hardware table,
however it missed the other table so it has still been fully allocated
at the boot time. This fixes the issue by allocating a single level,
just like we do for the hardware table.
Fixes: a68bd1267b ("powerpc/powernv/ioda: Allocate indirect TCE levels on demand")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add routines for Nemo specific devices to init at boot time, these
being board level power-off and SB600's rtc.
Also add a run time variable to prevent these being activated
if we boot on a reference board.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The A-Eon Amigaone X1000's Nemo motherboard has an AMD SB600
connected to one of the PCI-e root ports on its PaSemi
Pwrficient 1628M SoC. Normally the SB600 southbridge would be
connected to a hidden PCI-e port on the system's northbridge,
and as a result doesn't fully comply with the PCI-e spec.
Add code to relax the PCI-e detection in both the root port
and the Linux kernel allowing on board devices to be detected.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on
common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes.
Move to a scheme closer to what other architectures use (and I dare to
say the intent of the system):
- ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only)
- ZONE_NORMAL: everything addressable by the kernel
- ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels
Also provide information on how ZONE_DMA is used by defining
ARCH_ZONE_DMA_BITS.
Contains various fixes from Benjamin Herrenschmidt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share
any code with the one for systems with coherent caches. Split it off
and merge it with the helpers in dma-noncoherent.c that have no other
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
AMIGAONE selects NOT_COHERENT_CACHE, so we better allow it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch again, this has a couple of build fixes and also
a change to do_syscall_trace_enter() that will conflict with a patch we
want to apply in next.
The interleave set cookie is used to determine if a label stored in the
metadata space should be applied to the current region. This is
important in the case of NVDIMMs since the firmware may change the
interleaving configuration of a DIMM which would invalidate the existing
labels. In our case the hypervisor hides those details from us so we
don't really care, but libnvdimm still requires the interleave set
cookie to be non-zero.
For our purposes we just need the set cookie to be unique and fixed for
a given PAPR SCM region and using the unit-guid (really a UUID) is fine
for this purpose.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Use kernel types (u64)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a new nvdimm device is registered with libnvdimm via
nvdimm_create() it is added as a device on the nvdimm bus. The probe
function for the DIMM driver is potentially quite slow so actually
registering and probing the device is done in an async domain rather
than immediately after device creation. This can result in a race where
the region device (created 2nd) is probed first and fails to activate at
boot.
To fix this we use the same approach as the ACPI/NFIT driver which is to
check that all the DIMM devices registered successfully. LibNVDIMM
provides the nvdimm_bus_count_dimms() function which synchronises with
the async domain and verifies that the dimm was successfully registered
with the bus.
If either of these does not occur then we bail.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return values of a h-call are returned in the CPU registers and
written to the provided buffer by the plpar_hcall() wrapper. As a result
the values written to memory are always in the native endian and should
not be byte swapped.
The inital implementation of the H-Call interface was done in qemu and
the returned values were byte swapped unnecessarily in both the
hypervisor and in the driver so this was only noticed when bringing up
the PowerVM implementation.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm,unit-sizes property was originally specified as an array of two
u32s corresponding to the memory block size, and the number of blocks
available in that region. A fairly last-minute change to the SCM DT
specification was splitting that into two seperate u64 properties:
ibm,block-sizes and ibm,number-of-blocks that convey the same
information. No firmware / hypervisor that emitted the ibm,unit-size
property ever appeared in the wild.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Use kernel types (u32/u64)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix an off-by-one error in the memory resource range. This resource is
used to determine the address range of the memory to be hot-plugged as
ZONE_DEVICE memory. The current end address results in the kernel
attempting to map an additional memblock and the hypervisor may reject
the mapping resulting in the entire hot-plug failing.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Making PAPR_SCM select LIBNVDIMM results in circular dependencies in
Kconfig when another symbol depends on it. Fix this by replacing the
select with a depends.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Reported-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a plan to build the kernel with -Wimplicit-fallthrough and these
places in the code produced warnings, but because we build arch/powerpc
with -Werror, they became errors. Fix them up.
This patch produces no change in behaviour, but should be reviewed in
case these are actually bugs not intentional fallthoughs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC_STD_MMU_32 and PPC_STD_MMU are not used anymore. Remove them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_6xx is not used anymore. Remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today we have:
config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config 6xx
def_bool y
depends on PPC32 && PPC_BOOK3S
6xx is therefore redundant with PPC_BOOK3S_32.
In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_6xx in a later patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.
Replace the open coded iterating over child nodes with
for_each_child_of_node() while we're here.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need to have the 'void __iomem *cpld_base' variable static
since new value always be assigned before use it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The NPU IOMMU is setup to mirror the parent PCIe device IOMMU
setup. Therefore it does not make sense to call dma operations such as
dma_map_page(), etc. directly on these devices. The existing dma_ops
simply print a warning if they are ever called, however this is
unnecessary and the warnings are likely to go unnoticed.
It is instead simpler to remove these operations and let the generic
DMA code print warnings (eg. via a NULL pointer deref) in cases of
buggy drivers attempting dma operations on NVLink devices.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in /proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a fix for a
missing prototype warning."
A few other minor fixes and a handful of fixes for our selftests.
Thanks to:
Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe Leroy, Felipe Rechia,
Joel Stanley, Naveen N. Rao, Paul Mackerras, Scott Wood, Tyrel Datwyler.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJb3C+uAAoJEFHr6jzI4aWAPJgQAIX0aD/PiYfEUI/rm/Q0vnJI
HO3FCKroi+LVF/URU24+NLA/1KGCBfO9by9m6D/nnmHl+vi2P69fFgokywO0Ajru
nf9a+9Gx53IbO7EEUf1fZVwxCMobBqU8eWq1hIBndd5HTz9QEftc/RXgpgqZcQ/x
x8xN1FNMSUT9NwMk750QDO7CFBrSfSjFC+/WrkViBaMiRWx2rwle+2tDipQ/fegY
Tsu4wg0qEzWMT//MFP4yOlkcLV8M6d2Sw65Km59rWHA1I2wqsTek1yQ68Epo9Co0
RdJh9Nt1kjLC5XXteneFhe18UUPKRmrXbYDFByw5CUhs5VI99Dq4w5kamh197XLr
+jA3XHAeAyaXf21I9zmmZXbhHanowCPZGyzZqZXWJ86bVJp5v328wXmnxtKrb0Nz
pH7fjQ6zjzsZgIcN9i2CFpIvuDQ/z1A/QyHdBnRvJ8HoXlTerZCn22JTgY7d2VJu
XJn1n+VABG2BrzJexW/7quY3Z7V6tvdkloWwOA3PdAwkcoImd4BfYq9K2DU//diN
BnXPnDs2K7JwDG9s+cgUEHnrP6DOKsxT+mmYpqXf0Ta0wtyoZJ1zgSdfZAUOmjnb
MhcK46l+F4E891qjnsuuVNnspqI4yPMLmAGmife5OUrfcoFdm/vFbM75FaXameBx
cMOmidrJJhO6z5eWSKvO
=VCkW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork
was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in
/proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a
fix for a missing prototype warning"
A few other minor fixes and a handful of fixes for our selftests.
Thanks to: Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe
Leroy, Felipe Rechia, Joel Stanley, Naveen N. Rao, Paul Mackerras,
Scott Wood, Tyrel Datwyler"
* tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (21 commits)
selftests/powerpc: Fix compilation issue due to asm label
selftests/powerpc/cache_shape: Fix out-of-tree build
selftests/powerpc/switch_endian: Fix out-of-tree build
selftests/powerpc/pmu: Link ebb tests with -no-pie
selftests/powerpc/signal: Fix out-of-tree build
selftests/powerpc/ptrace: Fix out-of-tree build
powerpc/xmon: Relax frame size for clang
selftests: powerpc: Fix warning for security subdir
selftests/powerpc: Relax L1d miss targets for rfi_flush test
powerpc/process: Fix flush_all_to_thread for SPE
powerpc/pseries: add missing cpumask.h include file
selftests/powerpc: Fix ptrace tm failure
KVM: PPC: Use exported tb_to_ns() function in decrementer emulation
powerpc/pseries: Export maximum memory value
powerpc/8xx: Use patch_site for perf counters setup
powerpc/8xx: Use patch_site for memory setup patching
powerpc/code-patching: Add a helper to get the address of a patch_site
Revert "powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for CONFIG_SWAP"
powerpc/8xx: add missing header in 8xx_mmu.c
powerpc/8xx: Add DT node for using the SEC engine of the MPC885
...
Various powerpc boards select the PCI_MSI config option without selecting
PCI, resulting in potentially not compilable configurations if the by
default enabled PCI option is disabled. Explicitly select PCI to ensure
we always have valid configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
