The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlvPV7IUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyaUg//WnCaRIu2oKOp8c/bplZJDW5eT10d
oYAN9qeyptU9RYrg4KBNbZL9UKGFTk3AoN5AUjrk8njxc/dY2ra/79esOvZyyYQy
qLXBvrXKg3yZnlNlnyBneGSnUVwv/kl2hZS+kmYby2YOa8AH/mhU0FIFvsnfRK2I
XvwABFm2ZYvXCqh3e5HXaHhOsR88NQ9In0AXVC7zHGqv1r/bMVn2YzPZHL/zzMrF
mS79tdBTH+shSvchH9zvfgIs+UEKvvjEJsG2liwMkcQaV41i5dZjSKTdJ3EaD/Y2
BreLxXRnRYGUkBqfcon16Yx+P6VCefDRLa+RhwYO3dxFF2N4ZpblbkIdBATwKLjL
npiGc6R8yFjTmZU0/7olMyMCm7igIBmDvWPcsKEE8R4PezwoQv6YKHBMwEaflIbl
Rv4IUqjJzmQPaA0KkRoAVgAKHxldaNqno/6G1FR2gwz+fr68p5WSYFlQ3axhvTjc
bBMJpB/fbp9WmpGJieTt6iMOI6V1pnCVjibM5ZON59WCFfytHGGpbYW05gtZEod4
d/3yRuU53JRSj3jQAQuF1B6qYhyxvv5YEtAQqIFeHaPZ67nL6agw09hE+TlXjWbE
rTQRShflQ+ydnzIfKicFgy6/53D5hq7iH2l7HwJVXbXRQ104T5DB/XHUUTr+UWQn
/Nkhov32/n6GjxQ=
=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.
Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't actually need to check if the host mbx is ready when queuing
MAC requests, because these are not handled by a special queue which
queues up requests until the mailbox is capable of handling them.
Pull these requests outside the fm10k_host_mbx_ready() check, as it is
not necessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid potential bugs with fm10k_add_stat_strings and
fm10k_add_ethtool_stats by using a macro to calculate the ARRAY_SIZE
when passing. This helps ensure that the size is always correct.
Note that it assumes we only pass static const fm10k_stat arrays, and
that evaluation of the argument won't have side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a fixed prefix string we setup before each call to
fm10k_add_stat_strings, modify the helper to take variadic arguments and
pass them to vsnprintf. This requires changing the fm10k_stat strings to
take % format specifiers where necessary, but the resulting code is much
simpler.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Share some of the code for setting up fm10k_stat macros by implementing
an FM10K_STAT_FIELDS macro which we can use when setting up the type
specific macros.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have support for accelerating macvlan devices via the
.ndo_dfwd_add_station() netdev op. These accelerated macvlan MAC
addresses are stored in the l2_accel structure, separate from the
unicast or multicast address lists.
If a VLAN is added on top of the macvlan device by the stack, traffic
will not properly flow to the macvlan. This occurs because we fail to
setup the VLANs for l2_accel MAC addresses.
In the non-offloaded case the MAC address is added to the unicast
address list, and thus the normal setup for enabling VLANs works as
expected.
We also need to add VLANs marked from .ndo_vlan_rx_add_vid() into the
l2_accel MAC addresses. Otherwise, VLAN traffic will not properly be
received by the VLAN devices attached to the offloaded macvlan devices.
Fix this by adding necessary logic to setup VLANs not only for the
unicast and multicast addresses, but also the l2_accel list. We need
similar logic in dfwd_add_station, dfwd_del_station, fm10k_update_vid,
and fm10k_restore_rx_state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the ixgbe and fm10k drivers support destination filtering.
Instead of adding a ton of complexity to support either source or passthru
mode we can instead just avoid offloading them for now. Doing this we avoid
leaking packets into interfaces that aren't meant to receive them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drop dead code now that we shouldn't be receiving broadcast or multicast
frames on the queues associated to the macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use a software path for packets that are
going to be locally switched between two macvlan interfaces on the same
device. In addition we resort to software replication of broadcast and
multicast packets instead of offloading that to hardware.
The general idea is that using the device for east/west traffic local to
the system is extremely inefficient. We can only support up to whatever the
PCIe limit is for any given device so this caps us at somewhere around 20G
for devices supported by ixgbe. This is compounded even further when you
take broadcast and multicast into account as a single 10G port can come to
a crawl as a packet is replicated up to 60+ times in some cases. In order
to get away from that I am implementing changes so that we handle
broadcast/multicast replication and east/west local traffic all in
software.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
Note that the driver previously used dev_warn() to suggest using a
different slot, but pcie_print_link_status() uses dev_info() because if the
platform has no faster slot available, the user can't do anything about the
warning and may not want to be bothered with it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're aligned with latest version released on SourceForge, so update the
version number to match.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent kernels now complain about incorrect function prototype comments,
in order to ensure comments are accurate to the function. However, it
incorrectly associates the comment above the fm10k_pci_tbl[] as
a function header comment. Fix this by removing the extra "*" in the
comment. This normally indicates that the function is a doxygen style
function header comment.
Once removed, the logic no longer kicks in and the following warning is
fixed:
warning: cannot understand function prototype: 'const struct pci_device_id fm10k_pci_tbl[] = '
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several function header comments had incorrect function parameter
definitions. Recent versions of the upstream kernel have started to warn
about these issues. Fix up the comments which do not match in order to
resolve these new warnings.
While fixing these, update the copyright year also.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clarify the comment for when entering promiscuous mode that we update
the VLAN table. Add a comment distinguishing the case where we're
exiting promiscuous mode and need to clear the entire VLAN table.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@gmail.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 856dfd69e84f ("fm10k: Fix multicast mode synch issues",
2016-03-03) we've incorrectly assumed that VLAN 1 is enabled when the
default VID is not set.
This occurs because we check the default_vid and if it's zero, start
several loops over the active_vlans bitmask at 1, instead of checking to
ensure that that bit is active.
This happened because of commit d9ff3ee8efe9 ("fm10k: Add support for
VLAN 0 w/o default VLAN", 2014-08-07) which mistakenly assumed that we
should send requests for MAC and VLAN filters with VLAN 0 when the
default_vid isn't set.
However, the switch generally considers this an invalid configuration,
so the only time we'd have a default_vid of 0 is when the switch is
down.
Instead, lets just not request any filters for the default_vid if it's
not yet been assigned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when the driver loads, it sends a request to add VLAN 0 to the
VLAN table. For the PF, this is honored, and VLAN 0 is indeed set. For
the VF, this request is silently converted into a request for the
default VLAN as defined by either the switch vid or the PF vid.
This results in the odd behavior that the VLAN table doesn't appear
consistent between the PF and the VF.
Furthermore, setting a MAC filter with VLAN 0 is generally considered an
invalid configuration by the switch, and since commit 856dfd69e84f
("fm10k: Fix multicast mode synch issues", 2016-03-03) we've had code
which prevents us from ever sending such a request.
Since there's not really a good reason to keep VLAN 0 in the VLAN table,
stop requesting it in fm10k_restore_rx_state().
This might seem to indicate that we would no longer properly configure
the MAC and VLAN tables for the default vid. However, due to the way
that fm10k_find_next_vlan() behaves, it will always return the
default_vid as enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a VF is under PF VLAN assignment:
ip link set <pf> vf <#> vlan <vid>
This will remove all previous entries in the VLAN table including those
generated by VLAN interfaces created on the VF. The issue arises when
the VF is under PF VLAN assignment and one or more of these VLAN
interfaces of the VF are deleted. When deleting these VLAN interfaces,
the following message will be generated in "dmesg":
failed to kill vid 0081/<vid> for device <vf>
This is due to the fact that "ndo_vlan_rx_kill_vid" exits with an error.
The handler for this ndo is "fm10k_update_vid". Any calls to this
function while under PF VLAN management will exit prematurely and, thus,
it will generate the failure message.
Additionally, since "fm10k_update_vid" exits prematurely, none of the
VLAN update is performed. So, even though the actual VLAN interfaces of
the VF will be deleted, the active_vlans bitmask is not cleared. When
the VF is no longer under PF VLAN assignment, the driver mistakenly
restores the previous entries of the VLAN table based on an
unsynchronized list of active VLANs.
The solution to this issue involves checking the VLAN update action type
before exiting "fm10k_update_vid". If the VLAN update action type is to
"add", this action will not be permitted while the VF is under PF VLAN
assignment and the VLAN update is abandoned like before.
However, if the VLAN update action type is to "kill", then we need to
also clear the active_vlans bitmask. However, we don't need to actually
queue any messages to the PF, because the MAC and VLAN tables have
already been cleared, and the PF would silently ignore these requests
anyways.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes a few warnings found by checkpatch.pl --strict
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k driver didn't work correctly when macvlan offload was enabled.
Specifically what would occur is that we would see no unicast packets being
received. This was traced down to us not correctly configuring the default
VLAN ID for the port and defaulting to 0.
To correct this we either use the default ID provided by the switch or
simply use 1. With that we are able to pass and receive traffic without any
issues.
In addition we were not repopulating the filter table following a reset. To
correct that I have added a bit of code to fm10k_restore_rx_state that will
repopulate the Rx filter configuration for the macvlan interfaces.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2502:12: error: 'fm10k_suspend' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2475:12: error: 'fm10k_resume' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 8249c47c6b ("fm10k: use generic PM hooks instead of legacy PCIe power hooks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.
Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't hard code the function names in the diagnostic output when these
reset related routines fail. Instead, use %s and __func__ so that future
refactors don't need to change the print outs.
Additionally, while we are here, add missing function header comments
for the new reset_prepare and reset_done function handlers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct the backward logic using !net_ratelimit()
Miscellanea:
o Add a blank line before the error return label
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have a working MAC/VLAN queue for handling MAC/VLAN messages
from the netdev, replace the default handler for the VF<->PF messages.
This new handler is very similar to the default code, but uses the
MAC/VLAN queue instead of sending the message directly. Unfortunately we
can't easily re-use the default code, so we'll just replace the entire
function.
This ensures that a VF requesting a large number of VLANs or MAC
addresses does not start a reset cycle, as explained in the commit which
introduced the message queue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Ngai-mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under some circumstances, when dealing with a large number of MAC
address or VLAN updates at once, the fm10k driver, particularly the VFs
can overload the mailbox with too many messages at once.
This results in a mailbox timeout, which causes the driver to initiate
a reset. During the reset, we re-send all the same messages that
originally caused the timeout. This results in a cycle of resets each
triggering a future reset.
To fix or avoid this, we introduce a workqueue item which monitors
a queue of MAC and VLAN requests. These requests are queued to the end
of the list, and we process as a FIFO periodically.
Initially we only handle requests for the netdev, but we do handle
unicast MAC addresses, multicast MAC addresses, and update VLAN
requests.
A future patch will add support to use this queue for handling MAC
update requests from the VF<->PF mailbox.
The MAC/VLAN work item will keep checking to make sure that each request
does not overflow the mailbox and cause a timeout. If it might, then the
work item will reschedule itself a short time later. This avoids any
reset cycle, since we never send the message if the mailbox is not
ready.
As an alternative, we tried increasing the mailbox message FIFO, but
this just delays the problem and results in needless memory waste on the
system. Our new message queue is dynamically allocated so only uses as
much memory as it needs. Additionally, it need not be contiguous like
the Tx and Rx FIFOs.
Note that this patch chose to only create a queue for MAC and VLAN
messages, since these are the only messages sent in a large enough
volume to cause the reset loop. Other messages are very unlikely to
overflow the mailbox Tx FIFO so easily.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the PCI specific legacy power management hooks with the new
generic power management hooks which work properly for both suspend and
hibernate. The new generic system is better and properly handles the
lower level PCIe power management rather than forcing the driver to
handle it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lets not re-invent the locking wheel. Remove our bitlock and use
a proper spinlock instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we lose PCIe link, such as when an unannounced PFLR event occurs, or
when a device is surprise removed, we currently detach the device and
close the netdev. This unfortunately leaves a lot of things still
active, such as the msix_mbx_pf IRQ, and Tx/Rx resources.
This can cause problems because the register reads will return
potentially invalid values which may result in unknown driver behavior.
Begin the process of resetting using fm10k_prepare_for_reset(), much in
the same way as the suspend and resume cycle does. This will attempt to
shutdown as much as possible, in order to prevent possible issues.
A naive implementation for this has issues, because there are now
multiple flows calling the reset logic and setting a reset bit. This
would cause problems, because the "re-attach" routine might call
fm10k_handle_reset() prior to the reset actually finishing. Instead,
we'll add state bits to indicate which flow actually initiated the
reset.
For the general reset flow, we'll assume that if someone else is
resetting that we do not need to handle it at all, so it does not need
its own state bit. For the suspend case, we will simply issue a warning
indicating that we are attempting to recover from this case when
resuming.
For the detached subtask, we'll simply refuse to re-attach until we've
actually initiated a reset as part of that flow.
Finally, we'll stop attempting to manage the mailbox subtask when we're
detached, since there's nothing we can do if we don't have a PCIe
address.
Overall this produces a much cleaner shutdown and recovery cycle for
a PCIe surprise remove event.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although very unlikely, it is possible that cancel_work_sync() may stop
the service_task before it actually started. In this case, the
__FM10K_SERVICE_SCHED bit will never be cleared. This results in the
service task being unable to reschedule in the future. Add a helper
function which sets the service disable bit, waits for the service task
to stop and clears the schedule bit, thus avoiding the race condition.
We know the schedule bit is safe to clear because the cancel_work_sync()
guarantees the service task is not running.
Add a helper function also to restart the service task, for symmetry.
This is not strictly needed but helps the mental model of how to stop
and start the service task.
This race could only happen in fm10k_suspend/fm10k_resume as this is the
only place where the service task is actually restarted. Thus,
suspend/resume testing would be ideal. However, note that the chance of
this happening is very slim as the service event is scheduled for
immediate execution, and you would have to trigger a suspend at almost
the exact same time as the service task was scheduled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch needs these functions defined earlier in the file. Move
them closer to above where they will be called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
