Commit Graph

7760 Commits

Author SHA1 Message Date
Florian Fainelli
ad51c61061 net: systemport: correctly check for RX_STATUS_OVFLOW flag
We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:36:54 -07:00
Florian Fainelli
d8498088cf net: systemport: fix transmit locking scheme
Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:36:54 -07:00
Lendacky, Thomas
1ebe98dcd8 amd-xgbe: Configuration and build support
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:26:51 -07:00
Lendacky, Thomas
c5aa9e3b81 amd-xgbe: Initial AMD 10GbE platform driver
This patch provides the initial platform driver for the AMD
10GbE device.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:26:51 -07:00
Amos Kong
78c8dbb652 hplance: fix ram size in comment
drivers/net/ethernet/amd/hplance.h:
 #define HPLANCE_MEMOFF 0x8000   /* struct lance_init_block */
 #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */

The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.

Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:14:21 -07:00
Amos Kong
1cff389ddb mvme147: fix ram size in comment
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.

Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:14:21 -07:00
Andrew Ruder
582379839b dm9000: avoid sleeping in dm9000_timeout callback
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine.  Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:11 -07:00
Andrew Ruder
aac6d02280 dm9000: handle initial link status
On the DM9000A/DM9000B force the initial check of the link status.  The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in.  This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:11 -07:00
Andrew Ruder
36259012a4 dm9000: remove redundant ISR status clear
Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:10 -07:00
Andrew Ruder
17ad78de7f dm9000: clean up edge-triggered irq compatibility
DM9000 uses level-triggered interrupts.  Some systems (PXA270) only
support edge-triggered interrupts on GPIOs.  Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.

* Make some helper functions called dm9000_mask_interrupts() and
  dm9000_unmask_interrupts() for readability.

* dm9000_init_dm9000(): ensure that this function always leaves interrupts
  masked regardless of the state when it entered the function.  This is
  primarily to support the situation in dm9000_open where the logic used
  to go:

    dm9000_open()
        dm9000_init_dm9000()
            unmask interrupts
        request_irq()

  If an interrupt occurred between unmasking the interrupt and
  requesting the irq, it would be missed forever as the edge event would
  never be seen by the GPIO hardware in the PXA270.  This allows us to
  change the logic to:

    dm9000_open()
        dm9000_init_dm9000()
            dm9000_mask_interrupts()
        request_irq()
        dm9000_unmask_interrupts()

* dm9000_timeout(), dm9000_drv_resume(): Add the missing
  dm9000_unmask_interrupts() now required by the change above.

* dm9000_shutdown(): Use mask helper function

* dm9000_interrupt(): Use mask/unmask helper functions

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:10 -07:00
Andrew Ruder
751bb6fd80 dm9000: clean up reset code
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset

* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
  was called immediately before-hand.  Bring dm9000_reset into
  dm9000_init_dm9000.

* The following commit updated the dm9000_probe reset routine to use NCR_RST
  | NCR_MAC_LBK:

    6741f40 DM9000B: driver initialization upgrade

  and a later commit added a bug-fix to always reset the chip twice:

    09ee9f8 dm9000: Implement full reset of DM9000 network device

  Unfortunately, since the changes in 6741f40 were made by replacing the
  dm9000_probe dm9000_reset with the adjusted iow(), the changes in
  09ee9f8 were not incorporated into the dm9000_probe reset.
  Furthermore, it bypassed the requisite reset-delay causing some boards
  to get at least one "read wrong id ..." dev_err message during
  dm9000_probe.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:10 -07:00
Andrew Ruder
6b50d038e7 dm9000: acquire irq flags from device tree
The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM.  In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.

Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:12:10 -07:00
Rajesh Borundia
c531692073 qlcnic: Initialize mailbox cmd structure to zero
o Uninitialzed fields in mailbox command structure
  caused commands to time out randomly due to garbage
  values so initialize it to zero.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:06:09 -07:00
Fabio Estevam
d4c642ea12 gianfar: Call netif_carrier_off() prior to registration
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().

Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."

So call netif_carrier_off() prior to register_netdev().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05 15:03:46 -07:00
Shannon Nelson
41a9e55c89 i40e: add missing VSI statistics
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.

Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:58:13 -07:00
Shannon Nelson
03da6f6a4f i40e/i40evf: remove rx_errors and rx_missed
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.

Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:50:02 -07:00
Shannon Nelson
7812fddc9c i40e: refactor stats collection
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.

Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:42:55 -07:00
Jesse Brandeburg
44033fac14 i40e: refactor send version
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.

Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:34:59 -07:00
Kamil Krawczyk
4f4e17bd12 i40e/i40evf: VEB structure added, GTIME macro update
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.

Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:27:39 -07:00
Mitch Williams
263fc48f97 i40e: notify VF of all types of resets
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.

Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:20:19 -07:00
Mitch Williams
d732a18445 i40evf: fix crash when changing ring sizes
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.

Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.

Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:13:01 -07:00
Mitch Williams
337eb08e5a i40evf: set descriptor multiple to 32
Hardware requires descriptors to be allocated in groups of 32.

Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 02:05:35 -07:00
Jesse Brandeburg
61a46a4c07 i40e: clamp jumbo frame size
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.

The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.

Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 01:58:31 -07:00
Jesse Brandeburg
d0277054ac i40e/i40evf: remove unused RX_LRO define
Remove unused defines and macros for RX_LRO.

Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 01:49:18 -07:00
Kamil Krawczyk
c5cc0cfd27 i40e: remove check for large buffer
We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.

Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 01:35:07 -07:00
Kamil Krawczyk
22dd9ae8af i40e: Rework register diagnostic
Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.

Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 01:27:46 -07:00
Jesse Brandeburg
d3a90b70d8 i40e: don't use OR to check a value
A couple of FD checks ended up using bitwise OR to check
a value, which ends up always being evaluated to true.

This should fix the issue.  Thanks to DaveJ for noticing
and reporting the issue!

CC: Dave Jones <davej@redhat.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05 01:20:06 -07:00
Linus Torvalds
d09cc3659d Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core irq updates from Thomas Gleixner:
 "The irq department delivers:

   - Another tree wide update to get rid of the horrible create_irq
     interface along with its even more horrible variants.  That also
     gets rid of the last leftovers of the initial sparse irq hackery.
     arch/driver specific changes have been either acked or ignored.

   - A fix for the spurious interrupt detection logic with threaded
     interrupts.

   - A new ARM SoC interrupt controller

   - The usual pile of fixes and improvements all over the place"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
  Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding
  irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller
  genirq: Improve documentation to match current implementation
  ARM: iop13xx: fix msi support with sparse IRQ
  genirq: Provide !SMP stub for irq_set_affinity_notifier()
  irqchip: armada-370-xp: Move the devicetree binding documentation
  irqchip: gic: Use mask field in GICC_IAR
  genirq: Remove dynamic_irq mess
  ia64: Use irq_init_desc
  genirq: Replace dynamic_irq_init/cleanup
  genirq: Remove irq_reserve_irq[s]
  genirq: Replace reserve_irqs in core code
  s390: Avoid call to irq_reserve_irqs()
  s390: Remove pointless arch_show_interrupts()
  s390: pci: Check return value of alloc_irq_desc() proper
  sh: intc: Remove pointless irq_reserve_irqs() invocation
  x86, irq: Remove pointless irq_reserve_irqs() call
  genirq: Make create/destroy_irq() ia64 private
  tile: Use SPARSE_IRQ
  tile: pci: Use irq_alloc/free_hwirq()
  ...
2014-06-04 15:59:13 -07:00
Antonio Ospite
cef33c815a trivial: drivers/net/ethernet/nvidia/forcedeth.c: fix typo s/SUBSTRACT1/SUBTRACT1/
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04 15:07:42 -07:00
Xiubo Li
898157ed74 gianfar: Fix the section mismatch warnings.
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following
WARNING is occured:

  LD      drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in
reference from the function gfar_probe() to the function
.init.text:gfar_init_addr_hash_table()
The function gfar_probe() references
the function __init gfar_init_addr_hash_table().
This is often because gfar_probe lacks a __init
annotation or the annotation of gfar_init_addr_hash_table is wrong.

Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04 14:55:23 -07:00
David S. Miller
9bcc14d239 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e1000, igb and ixgbe.

Emil provides his version 2 fix for the detection of SFP+ capable interfaces.
In cases where the driver is loaded while there are no SFP+ modules in cage,
the interface was not being detected as SFP capable.  Resolve the issue by
identifying interfaces with no PHY type set as SFP capable which allows the
driver to detect the SFP module when the interface is brought up.  In this
version 2 of the patch, the 82599 specific check was removed since we only
have 82598 devices that are SFP capable.

Jacob removes the including of the export header in the ixgbe PTP core, since
it is not needed.  Renames igb_ptp_enable() to igb_ptp_feature_enable() to
better reflect the actual functions purpose.

Todd fixes the ethtool loopback test for i354 backplane devices since we
do not know what PHY is to be used for the devices, use MAC loopback for
ethtool tests.  Todd also sets the packet buffer size register defaults for
i210 devices.

Yongjian Xu removes the check for skb->len being negative or zero since there
is never a case where it would be zero or negative for e1000.

Manuel Schölling updates e1000 to use the time_after() helper function.

v2: Fix indentation on wrapped line in patch 3 of the series based on
    feedback from David Miller
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04 14:40:17 -07:00
Roland Dreier
4e2c341b86 mlx4_core: Fix GFP flags parameters to be gfp_t
Otherwise sparse gives a bunch of warnings like

    drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: sparse: incorrect type in argument 4 (different base types)
    drivers/net/ethernet/mellanox/mlx4/srq.c:110:66:    expected int [signed] gfp
    drivers/net/ethernet/mellanox/mlx4/srq.c:110:66:    got restricted gfp_t

Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-06-04 10:19:13 -07:00
Manuel Schölling
1aa65f4d7f e1000: Use time_after() for time comparison
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of plain, error-prone math.

Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:58:06 -07:00
Yongjian Xu
c46d150404 e1000: remove the check: skb->len<=0
There is no case skb->len would be 0 or 'negative'.
Remove the check.

Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:57:57 -07:00
Todd Fujinaka
27dff8b2f6 igb: add defaults for i210 TX/RX PBSIZE
Set the defaults on probe for the packet buffer size registers for the
i210.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:57:53 -07:00
Todd Fujinaka
3cfcf036e1 igb: use mac loopback for i354 backplane
We can't know what PHY is to be used for i354 backplane, so use MAC
loopback for ethtool tests.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:57:45 -07:00
Jacob Keller
102be52ffd igb: rename igb_ptp_enable to igb_ptp_feature_enable
The name igb_ptp_enable is not synonymous with the purpose of this
function, so rename it to better explain its purpose.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:57:19 -07:00
Jacob Keller
4dace98e72 ixgbe: remove linux/export.h header from ixgbe_ptp.c
We don't need this header file, so we shouldn't be including it.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:56:22 -07:00
Emil Tantilov
d9cd46cd39 ixgbe: fix detection of SFP+ capable interfaces
In cases where the driver is loaded while there are no SFP+ modules in
the cage the interface was not being detected as SFP capable. To account
for this the driver called identify_sfp in ixgbe_get_settings to make
sure the data is correct. However when there is no SFP+ module in the cage
the driver waits for the I2C reads to time out which can take more than a
second and will cause issues with tools (like net-snmp) that may poll
for that information.

This patch resolves the issue by identifying interfaces with no PHY
type set as SFP capable which allows the driver to detect the SFP module
when the interface is brought up. As result of this we can also remove the
identify_sfp call from ixgbe_get_settings.

v2: remove the 82599 specific check since we have 82598 devices that are SFP
capable.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 23:56:16 -07:00
David S. Miller
c99f7abf0e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	include/net/inetpeer.h
	net/ipv6/output_core.c

Changes in net were fixing bugs in code removed in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 23:32:12 -07:00
Sergei Shtylyov
d8b0426af5 sh_eth: fix SH7619/771x support
Commit 4a55530f38 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support.  Add the missing entries using  the data
from before that commit.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 19:28:42 -07:00
Ben Dooks
530aa2d0d9 sh_eth: use RNC mode for packet reception
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.

This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:

	net eth0: Receive FIFO Overflow

Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).

I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet.  There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.

There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.

Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 19:28:42 -07:00
wenxiong@linux.vnet.ibm.com
9aaae044ab bnx2x: Fix kernel crash and data miscompare after EEH recovery
A rmb() is required to ensure that the CQE is not read before it
is written by the adapter DMA.  PCI ordering rules will make sure
the other fields are written before the marker at the end of struct
eth_fast_path_rx_cqe but without rmb() a weakly ordered processor can
process stale data.

Without the barrier we have observed various crashes including
bnx2x_tpa_start being called on queues not stopped (resulting in message
start of bin not in stop) and NULL pointer exceptions from bnx2x_rx_int.

Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 18:37:38 -07:00
wenxiong@linux.vnet.ibm.com
0c0e63410a bnx2x: Adapter not recovery from EEH error injection
When injecting EEH error to bnx2x adapter, adapter couldn't be recovery
and caused recursive EEH errors. The patch fixes the issue.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 18:37:38 -07:00
Balakumaran Kannan
31f6f291b6 net: driver: smsc: set NOCARRIER flag in dev at driver initialization
As smsc driver supports carrier detection, it should unset NOCARRIER
flag only after carrier state determination. By default that flag
is off so driver should set it before starting auto-negotiation

Signed-off-by: Balakumaran <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 18:20:38 -07:00
Benoit Taine
9323b23995 lpc_eth: Use resource_size instead of computation
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/resource_size.cocci

Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03 16:08:52 -07:00
Linus Torvalds
776edb5931 Merge branch 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next
Pull core locking updates from Ingo Molnar:
 "The main changes in this cycle were:

   - reduced/streamlined smp_mb__*() interface that allows more usecases
     and makes the existing ones less buggy, especially in rarer
     architectures

   - add rwsem implementation comments

   - bump up lockdep limits"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
  rwsem: Add comments to explain the meaning of the rwsem's count field
  lockdep: Increase static allocations
  arch: Mass conversion of smp_mb__*()
  arch,doc: Convert smp_mb__*()
  arch,xtensa: Convert smp_mb__*()
  arch,x86: Convert smp_mb__*()
  arch,tile: Convert smp_mb__*()
  arch,sparc: Convert smp_mb__*()
  arch,sh: Convert smp_mb__*()
  arch,score: Convert smp_mb__*()
  arch,s390: Convert smp_mb__*()
  arch,powerpc: Convert smp_mb__*()
  arch,parisc: Convert smp_mb__*()
  arch,openrisc: Convert smp_mb__*()
  arch,mn10300: Convert smp_mb__*()
  arch,mips: Convert smp_mb__*()
  arch,metag: Convert smp_mb__*()
  arch,m68k: Convert smp_mb__*()
  arch,m32r: Convert smp_mb__*()
  arch,ia64: Convert smp_mb__*()
  ...
2014-06-03 12:57:53 -07:00
Zhangfei Gao
57c5bc9ad7 net: hisilicon: add hix5hd2 mac driver
Add support for the hix5hd2 XGMAC 1Gb ethernet device.
The controller requires two queues for tx and two queues for rx.
Controller fetch buffer from free queue and then push to used queue.
Diver should prepare free queue and free buffer from used queue.

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:39:05 -07:00
Michael Chan
5943691442 cnic: Fix missing ISCSI_KEVENT_IF_DOWN message
The iSCSI netlink message needs to be sent before the ulp_ops is cleared
as it is sent through a function pointer in the ulp_ops.  This bug
causes iscsid to not get the message when the bnx2i driver is unloaded.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:16:41 -07:00
Michael Chan
437b8a26f9 cnic: Don't take cnic_dev_lock in cnic_alloc_uio_rings()
We are allocating memory with GFP_KERNEL under spinlock.  Since this is
the only call manipulating the cnic_udev_list and it is always under
rtnl_lock, cnic_dev_lock can be safely removed.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:16:41 -07:00
Michael Chan
20f30c2d5e cnic: Don't take rcu_read_lock in cnic_rcv_netevent()
Because the called function, such as bnx2fc_indicate_netevent(), can sleep,
we cannot take rcu_lock().  To prevent the rcu protected ulp_ops from going
away, we use the cnic_lock mutex and set the ULP_F_CALL_PENDING flag.
The code already waits for ULP_F_CALL_PENDING flag to clear in
cnic_unregister_device().

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:16:41 -07:00
Christian Riesch
74f43922dc net: davinci_emac: Remove unwanted debug/error message
In commit cd11cf5053 I accidentally
added an error message. I used it for debugging and forgot to remove
it before submitting the patch.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:13:38 -07:00
David S. Miller
014b20133b Merge branch 'ethtool-rssh-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bwh/net-next
Ben Hutchings says:

====================
Pull request: Fixes for new ethtool RSS commands

This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:

1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations

I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.

v2: Update RSS operations in vmxnet3 too
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 23:07:02 -07:00
Ben Hutchings
fe62d00137 ethtool: Replace ethtool_ops::{get,set}_rxfh_indir() with {get,set}_rxfh()
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03 02:42:44 +01:00
Fabio Estevam
a68ab98e6c fec: Include pinctrl header file
Commit 5bbde4d2ec ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:

drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]

In order to fix the build error, include the linux/pinctrl/consumer.h header
file.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 18:03:35 -07:00
Jean Delvare
3aab01d800 net: ec_bhf: Add runtime dependencies
The ec_bhf driver is specific to the Beckhoff CX embedded PC series.
These are based on Intel x86 CPU. So we can add a dependency on
X86, with COMPILE_TEST as an alternative to still allow for broader
build-testing.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Darek Marcinkiewicz <reksio@newterm.pl>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 17:02:28 -07:00
Peter Senna Tschudin
f6d9b514de vxge: Remove useless return variables
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:58:13 -07:00
Peter Senna Tschudin
b2bda2f745 bnx2x: Remove useless return variables
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.

Verified by compilation only.

The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
    when strict
return
- ret
+ C
;
// </smpl>

Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:58:13 -07:00
Paul Gortmaker
3afc557d77 drivers/net: fix broadcom/bcmsysport.c compile fail on SPARC
To fix:

  CC      drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1

we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision.  For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:45:34 -07:00
Ezequiel Garcia
b926260c05 net: mv643xx_eth: Avoid unmapping the TSO header buffers
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.

Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:06 -07:00
Ezequiel Garcia
eee492ea35 net: mv643xx_eth: Drop the NETDEV_TX_BUSY return path
After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:06 -07:00
Ezequiel Garcia
ee9e49561b net: mv643xx_eth: Limit the TSO segments and adjust stop/wake thresholds
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.

In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:06 -07:00
Ezequiel Garcia
dd11680d0e net: mv643xx_eth: Count dropped packets properly
This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:06 -07:00
Ezequiel Garcia
2e3173a3d3 net: mvneta: Avoid unmapping the TSO header buffers
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.

Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:05 -07:00
Ezequiel Garcia
ba7e46ef9d net: mvneta: Fix missing DMA region unmap
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.

This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:05 -07:00
Ezequiel Garcia
8eef5f9723 net: mvneta: Limit the TSO segments and adjust stop/wake thresholds
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.

In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:05 -07:00
Ezequiel Garcia
9fa9379dcb net: mvneta: Use default NAPI weight instead of a custom one
This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 16:16:05 -07:00
Jiri Kosina
40f2287bd5 IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive.  Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-06-02 14:58:11 -07:00
Chen-Yu Tsai
d7ec858413 net: stmmac: Handle different error codes from platform_get_irq_byname
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:

  ad69674 of/irq: do irq resolution in platform_get_irq_byname()

As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:

  http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html

This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 14:04:06 -07:00
Alexander Duyck
f009618ac5 enic: Update driver to use __dev_uc/mc_sync/unsync calls
This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls.  Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.

Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.

This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 10:40:54 -07:00
Emil Goode
86c92ee3a2 stmmac: Remove spin_lock call in stmmac_get_pauseparam()
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.

commit cab6715c3e
Author: Yang Wei <Wei.Yang@windriver.com>
Date:   Sun May 25 09:53:44 2014 +0800

    net: driver: stmicro: Remove some useless the lock protection

This introduced the following sparse warning:

drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
	context imbalance in 'stmmac_get_pauseparam' -
	different lock contexts for basic block

Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 10:38:14 -07:00
David S. Miller
96b2e73c54 Revert "net/mlx4_en: Use affinity hint"
This reverts commit 70a640d0da.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 00:18:48 -07:00
Stephen Boyd
d64eed1d9b net: ks8851: Don't use regulator_get_optional()
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.

Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02 00:13:51 -07:00
David S. Miller
ee39facbf8 net: Revert mlx4 cpumask changes.
This reverts commit 70a640d0da
("net/mlx4_en: Use affinity hint") and commit
c8865b64b0 ("cpumask: Utility function
to set n'th cpu - local cpu first") because these changes break
the build when SMP is disabled amongst other things.

Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01 21:58:02 -07:00
Stephen Boyd
2a82e40d6b net: ks8851: Don't use regulator_get_optional()
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.

Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01 19:47:27 -07:00
Yuval Atias
70a640d0da net/mlx4_en: Use affinity hint
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.

We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it.  To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores.  If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.

Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01 19:16:29 -07:00
David S. Miller
648d4febcc Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e and i40evf.

Kevin updates the i40e and i40evf driver i40e_check_asq_alive() to ensure
the length register offset is non-zero which indicates that the software
has initialized the admin queue.  Also removes PCTYPE definitions which are
now reserved.

Mitch enables descriptor prefetch for rings belonging to the virtual function.
Also configures the VF minimum transmit rate to 50 Mbps rather than 0 which was
be interpreted as no limit at all.  Mitch found in order for the VF to achieve
its programmed transmit rate, we need to set the max credit value to 4.
Lastly fixes a Tx hang and firmware crash that happens after setting the MTU
on a VF by not using the RESETTING state during reinit, this is because
the RESETTING state means that a catastrophic hardware bad thing is happening
and the driver needs to tiptoe around and not use the admin queue or registers.
A reinit is no big deal and we can use the admin queue (and we should) so
do not set the state to RESETTING during reinit to resolve the bug.

Akeem changes the declaration of the transmit and receive rings inside
several loops to eliminate declaring the same ring every time for the
duration of the loop and declares them just once before the loop.  Also fixes
the driver to clear the recovery pending bit if pf_reset fails instead of
falling through the setup process.

Anjali makes a change based on feedback from Ben Hutchings that cmd->data
needs to be reported in ETHTOOL_GRXCLSRLCNT and use a helper function to
calculate the total filter count.

Jesse removes storm control since the storm control features are not apart
of the hardware and were mistakenly left in the code.

Greg changes tx_lpi_status and rx_lpi_status from bool to u32 to avoid
sparse errors.

Shannon adds the clear_pxe AdminQ API call to tell the firmware that the
driver is taking over from PXE.  In addition, relaxes the firmware API
check to allow more flexibility in handling newer NICs and NVMs in the field.

Vasu ensures that FCoE is disabled for MFP modes since it is not supported
by overriding the hardware FCoE capability.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:51:27 -07:00
Sathya Perla
3acf19d949 be2net: cleanup MCC async event processing code
The MCC async event processing code has 2 issues:
a) because of long struct names the code indentation is badly broken
b) description and definitions of how an MCC completion is interpreted as
   an async event are confusing (for e.g. the last word of an MCC event is
   named "code", while "code" is just a sub-field of the last word.)

This patch fixes the structure definitions, comments and re-factors code
as needed.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Sathya Perla
559b633f42 be2net: move async cmd processing to a separate routine
For some FW cmds, the caller just issues the cmd and doesn't wait for a
response. The response handling is done in the MCCQ compl processing context
only. Move this code into a separate routine to make be_mcc_compl_process()
more manageable.

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Kalesh AP
4c60005fe7 be2net: re-factor MCCQ error status handling code
This patch improves MCCQ error status handling in the following ways:
a) A MCC cmd completion returns a base-status and an addl-status.
So far, the routine be_mcc_compl_process() returned only the "status" value.
Now, embedd both statuses in the return value and let the caller routine access
the value of interest using base_status() and addl_status() macros.

b) Rename variables accordingly (base/addl) to avoid confusion while error
checking.

b) Some of the errors returned by FW are harmless and so an error msg is not
logged for such errors. Capture this logic in a separate routine to make the
code more readable.

Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Vasundhara Volam
96c9b2e45e be2net: support flashing new regions on Skyhawk-R
Certain new flash regions have been added to Skyhawk-R FW image. The newer
FW images specify op_types for each region. A region is flashed only
when it's CRC doesn't match that of the region on the HW flash. While
upgrading to a new FW image the driver is expected to tolerate certain
errors.

This patch re-factors code under be_flash() to support the above scheme.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Ravikumar Nelavelli
0f77ba7353 be2net: fixup TX-rate setting code for Skyhawk-R
Skyhawk-R FW supports TX-rate setting only as a % value of the link
speed, set via the SET_PROFILE_CONFIG cmd.

This patch makes the necessary changes to the FW cmd descriptors to support
the above change and also introduces checks in be_set_vf_tx_rate() to allow
only discrete values (that map to % of the link-speed).

Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Kalesh AP
a079488570 be2net: skip multicast promiscuos setting in already set
Set mc-promisc (multicast promiscuous) mode on an interface, only if it is
*not already* in that mode.

Also removed logs that report interface being set to multicast
promiscous mode. In an earlier comment on the netdev list such log messages
were deemed unnecessary as this behaviour is common across most of the
ethernet drivers.

Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:27:33 -07:00
Tobias Klauser
884460178f net: tile: Remove unnecessary memset of netdev private data
The memory for private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero it again in the driver.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:06:23 -07:00
Tobias Klauser
d581ebf5a1 net: tile: Use helpers from linux/etherdevice.h to check/set MAC
Use is_zero_ether_addr() to check for the MAC address being all zeros instead of
open coding the check.

Also use ether_addr_copy() instead of a manual memcpy() to set the
netdev->dev_addr.

Furthermore, get rid of a redundant assignment of netdev->addr_len. This is
already set by ether_setup() which is called in tile_net_setup().

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:06:23 -07:00
Ariel Elior
08f6dd89d2 bnx2x: update MAINTAINERS for bnx2x and e-mail addresses
The bnx2x development team has transferred from Broadcom to Qlogic.
This patch updates some obsolete email addresses to usable ones.
The bnx2x files contain headers with legal information from
Broadcom. Qlogic Legal depratment is taking their time coming up
with their own legal info. So this patch only updates contact
information. I will follow up with a patch for the headers once I
have the required info.

Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:04:26 -07:00
Nimrod Andy
5bbde4d2ec net: fec: use pinctrl PM helpers
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 17:03:21 -07:00
Jack Morgenstein
111c6094bd net/mlx4_core: Reset RoCE VF gids when guest driver goes down
Reset the GIDs assigned to a VF in the port RoCE GID table when
that guest goes down (either crashes or goes down cleanly).

As part of this fix, we refactor the RoCE gid table driver copy,
moving it to the mlx4_port_info structure (together with the MAC
and VLAN tables).

As with the MAC and VLAN tables, we now use a mutex per port
for the GID table so that modifying the driver copy and
modifying the firmware copy of a port GID table becomes an
atomic operation (thus avoiding driver-copy/FW-copy mismatches).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 16:57:52 -07:00
Ivan Mikhaylov
09271db6e0 emac: aggregation of v1-2 PLB errors for IER register
Aggreagation of version 1-2 because of version 1 can hit
PLB errors too. If it's not set so we missing events for PLB bits
and driver can't process those interrupts.

Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 16:29:57 -07:00
Ivan Mikhaylov
faacd3af0c emac: add missing support of 10mbit in emac/rgmii
In chips of emac/rgmii b'000' for 0/1 channel isn't suitable which
resulted in non working network interface in this mode.

Signed-off-by: Ivan Mikhaylov <ivan@ru.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 16:29:57 -07:00
Govindarajulu Varadarajan
958c492c55 enic: Fix 64 bit divide on 32bit system
Division of a 32 bit number by a 64 bit number causes the following link
error introduced by
7c2ce6e60f "enic: Add support for adaptive interrupt coalescing"

drivers/built-in.o: In function `enic_poll_msix':
enic_main.c:(.text+0x48710a): undefined reference to `__udivdi3'
make: *** [vmlinux] Error 1

Since numerator is 32 bit, convert denominator to 32 bit accordingly.

Fixes: 7c2ce6e60f ("enic: Add support for adaptive interrupt coalescing")
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 15:54:46 -07:00
Himangi Saraogi
09b38aa1e7 ehea: Introduce the use of the managed version of kzalloc
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available.

The following Coccinelle semantic patch was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Compile-Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-30 15:40:29 -07:00
Roland Dreier
165cb465f7 mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
The handling of MLX4_QP_ST_MLX in verify_qp_parameters() was
accidentally put inside the inner switch statement (that handles which
transition of RC/UC/XRC QPs is happening).  Fix this by moving the case
to the outer switch statement.

The compiler pointed this out with:

    drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'verify_qp_parameters':
 >> drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2875:3: warning: case value '7' not in enumerated type 'enum qp_transition' [-Wswitch]
       case MLX4_QP_ST_MLX:

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 99ec41d0a4 ("mlx4: Add infrastructure for selecting VFs to enable QP0 via MLX proxy QPs")
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-30 15:38:58 -07:00
Jack Morgenstein
65fed8a8c1 IB/mlx4: Add interface for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.

By default, no VFs are enabled for QP0 operation.

To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:

- smi_enabled (read-only). Indicates whether smi is currently
  enabled for the indicated VF/port

- enable_smi_admin (rw). Used by the admin to request that smi
  capability be enabled or disabled for the indicated VF/port.
  0 = disable, 1 = enable.
  The requested enablement will occur at the next reset of the
  VF (e.g. driver restart on the VM which owns the VF).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:19 -07:00
Jack Morgenstein
99ec41d0a4 mlx4: Add infrastructure for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:09 -07:00
Jack Morgenstein
97982f5a91 IB/mlx4: Preparation for VFs to issue/receive SMI (QP0) requests/responses
Currently, VFs in SRIOV VFs are denied QP0 access.  The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology.  Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.

However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.

This commit does the following:

1. Create QP0 tunnel QPs for all VFs.

2. Discard SMI mads sent-from/received-for non-privileged VFs in the
   hypervisor MAD multiplex/demultiplex logic.  SMI mads from/for
   privileged VFs are allowed to pass.

3. MAD_IFC wrapper changes/fixes.  For non-privileged VFs, only
   host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
   GET mads.  For privileged VFs, there are no restrictions.

This commit does not allow privileged VFs as yet.  To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled().  This function
returns 0 unconditionally for now.

The next two commits allow defining and activating privileged VFs.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:12:58 -07:00
Jack Morgenstein
bc82878baa mlx4_core: Fix incorrect FLAGS1 bitmap test in mlx4_QUERY_FUNC_CAP
Commit eb17711bc1 ("net/mlx4_core: Introduce nic_info new flag in
QUERY_FUNC_CAP") did:

	if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_OFFSET) {

which should be:

	if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_FORCE_VLAN) {

Fix that.

Fixes: eb17711bc1 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:12:58 -07:00
Dotan Barak
b38f2879b7 mlx4_core: Fix memory leaks in SR-IOV error paths
Fix a few memory leaks that happen if errors happen in SR-IOV mode.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:12:58 -07:00
Shannon Nelson
7e612411e7 i40e: relax the firmware API version check
As long as the Firmware isn't reporting a higher API major version number
than what the driver knows about, the driver does not need to worry as
much about greater minor numbers.  The API changes minor numbers when
things get added to the API, but no existing structs or calls are changed.
The driver has the option of warning that the minor numbers don't match.

This will allow a little more flexibility in handling newer NICs and NVMs
in the field.

Change-ID: I5302acd2d147a2992328991ee7223b2ff39c8741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 05:55:44 -07:00
Mitch Williams
0efe124008 i40evf: don't use RESETTING state during reinit
The RESETTING state means that a Catastrophic Hardware Bad Thing is
happening and the driver need to tiptoe around and not use the admin
queue or registers or anything like that.

On the other hand, a reinit is no big deal and we can use the admin
queue, and we should. So don't set the state to RESETTING here.

This fixes a Tx hang and FW crash that happens after setting the MTU on
a VF.

Change-ID: I3e6191edbd6a93958a1f1bd1d41a5c2d17474d41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:53:10 -07:00
Vasu Dev
566bb85db7 i40: disable FCoE for MFP modes
Currently FCoE is not supported with MFP modes, so this patch
makes sure it is disabled.

It is disabled by overriding HW FCoE capability, so that later
it can be re-enabled by just the SW upgrade.

Change-ID: I1c0bae5c099b209f56b88bda360031a8565e43e8
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:46:14 -07:00
Shannon Nelson
c9b9b0aeac i40e: add clear_pxe AdminQ request
Add the clear_pxe AdminQ API call.

Change-ID: Ia770ff3404971bb3889b53a39c3a7bfaf3f4d399
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:38:45 -07:00
Akeem G Abodunrin
b556540030 i40e: Clear recovery pending, if reset failed
If pf_reset failed, it becomes necessary to clear recovery pending bit, instead
of falling through the setup process.

Change-ID: Ic1611e6a32741fe3a2782ec7be173cb65e7492ed
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:30:45 -07:00
Greg Rose
10bc478a2a i40e/i40evf: Change type to u32 to avoid sparse error
tx_lpi_status and rx_lpi_status are declared as bool but then used in sizeof
operations in the CORE driver code.  Make them u32 to make sparse be quiet.

Change-ID: Iad6daeb1c7149e61ece242acd18c64b320c246a3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:22:56 -07:00
Jesse Brandeburg
aee8087f6b i40e/i40evf: remove storm control
The storm control features are not part of the hardware
and mistakenly were left in the code.  Remove them as
they are not needed any more.

Change-ID: I6e9277c8da2c52e69348a657bae25271449c2099
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 04:13:09 -07:00
Anjali Singhai Jain
8913278301 i40e: Use the new i40e_get_fd_cnt_all function in other places
We have a function to calculate this, so update the code to use the function.

Change-ID: Ia345b6fe6ec7f0b2dcf1199471b0d0f959ad3908
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 03:58:45 -07:00
Anjali Singhai Jain
082def103d i40e: Report cmd->data in ETHTOOL_GRXCLSRLCNT instead of ETHTOOL_GRXCLSRULE
Based on review feedback from upstream cmd->data is not
defined in ETHTOOL_GRXCLSRULE but needs to be reported in
ETHTOOL_GRXCLSRLCNT. Also use a helper function to calculate the total
filter count.

Change-ID: Iaacbf729527b73290c4fdad837b379b44fd7dd20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 03:51:09 -07:00
Kevin Scott
b2d36c03ef i40e/i40evf: Remove reserved PCTYPE defines
Patch to remove PCTYPE definitions which are now reserved.

Change-ID: I66c1c16a45a16f4894b2983101ab2a48ce03f1f4
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 03:12:42 -07:00
Akeem G Abodunrin
e7046ee1f8 i40e: Tx/Rx rings declaration
This patch changes the declaration of Tx/Rx rings inside several loops. It
eliminates declaring the same rings every time for the duration of the loop,
instead declaring them once before the loop.

Change-ID: I59dea54276f18c47dca522f520c18f65fe42a15d
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 02:48:04 -07:00
Mitch Williams
84590fd90e i40evf: tweak Tx rate params and de-magic-ify
In order for the VF to achieve its programmed Tx rate, we need to set
the max credits value to 4. While we're at it, get rid of some magic
numbers.

Change-ID: I4f17b4d3a90f1e069bdd134a543f0aa22feac3a9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 02:37:38 -07:00
Mitch Williams
dac9b31a18 i40evf: don't round Tx rate down to 0
Because the hardware configures VF Tx rates in increments of 50 Mbps,
values smaller than that would be rounded down to 0, which was
interpreted as no limit at all. Rather than do this, we round up to 50
Mbps and notify the user.

Change-ID: I5275848233fe7514cf93e11323661c68f4c38737
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 02:22:07 -07:00
Mitch Williams
50d41659fa i40e: enable descriptor prefetch for VFs
As recommended by the hardware guys, enable descriptor prefetch for
rings belonging to VFs. This matches a change already made for ring
belonging to the PF.

Change-ID: Idcc4dc7064bc9144ea81f5701ad07b7ecd11ba49
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 02:02:25 -07:00
Kevin Scott
8b833b4faa i40e/i40evf: Update check for AQ aliveness
Update the i40e_check_asq_alive check to ensure that the len register
offset is non-zero, indicating that SW has initialized the AQ.

Change-ID: I9c2e804788b4775bef9c7e80954ab004e6bdb306
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-29 02:02:25 -07:00
Haggai Eran
b475598aec mlx5_core: Store MR attributes in mlx5_mr_core during creation and after UMR
The patch stores iova, pd and size during mr creation and after UMRs
that modify them.  It removes the unused access flags field.

Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-27 11:53:06 -07:00
Tobias Klauser
dc5f2de6f8 i40evf: Use is_multicast_ether_addr helper
Use the is_multicast_ether_addr helper function from linux/etherdevice.h
instead of open coding the multicast address check.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:45 -07:00
Tobias Klauser
9760822b0d e1000: Use is_broadcast_ether_addr/is_multicast_ether_addr helpers
Use the is_broadcast_ether_addr/is_multicast_ether_addr helper functions
from linux/etherdevice.h instead of open coding them.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:44 -07:00
Todd Fujinaka
18cae6f7bb igb: remove redundant PHY power down register write
One of the registers used to power down the PHY was found to be wrong
(should be bit 2 not bit 1) on further inspection it was also found to
be redundant.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:44 -07:00
Andi Kleen
c6f3148c5b e1000e: Out of line __ew32_prepare/__ew32
Out of lining these two common inlines saves about 30k text size,
due to their errata workarounds.

14131431	2008136	1507328	17646895	10d452f	vmlinux-before-e1000e
14101415	2004040	1507328	17612783	10cbfef	vmlinux-e1000e

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:44 -07:00
David Ertman
50844bb7f4 e1000e: Fix expand setting EEE link info to all affected parts
Previously, the update_phy_task was only calling e1000_set_eee_pchlan()
for phy.type 82579.  This patch is to cause this function to be called
for 82579 and newer phy.types.  This causes the dev_spec->eee_lp_ability
to have the correct value when going into SX states.

Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:43 -07:00
David Ertman
261a7d121e e1000e: Cleanup parenthesis around return value
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:10:43 -07:00
Todd Fujinaka
5e7ff97004 e1000e: 82574/82583 TimeSync errata for SYSTIM read
Due to a synchronization error, the value read from SYSTIML/SYSTIMH
might be incorrect.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-27 02:09:57 -07:00
David Ertman
b3e5bf1ff3 e1000e: Failure to write SHRA turns on PROMISC mode
Previously, the check to turn on promiscuous mode only took into account
the total number of SHared Receive Address (SHRA) registers and if the
request was for a register within that range.  It is possible that the
Management Engine might have locked a number of SHRA and not allowed a
new address to be written to the requested register.

Add a function to determine the number of unlocked SHRA registers.  Then
determine if the number of registers available is sufficient for our needs,
if not then return -ENOMEM so that UNICAST PROMISC mode is activated.

Since the method by which ME claims SHRA registers is non-deterministic,
also add a return value to the function attempting to write an address
to a SHRA, and return a -E1000_ERR_CONFIG if the write fails.  The error
will be passed up the function chain and allow the driver to also set
UNICAST PROMISC when this happens.

Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:11 -07:00
Jacob Keller
a0cccce2ce ixgbe: avoid duplicate code in suspend and stop paths
Resume path calls .open but suspend path cannot call .stop because
fdirs should not be freed and control over hardware should not be
released until WoL is configured.  To avoid having to duplicate all
changes made in .stop on suspend path split out part of .stop that
is relevant during suspend and call it from .stop and during suspend.

This fix also ensures that ixgbe_ptp_suspend is called during the
suspend path, and helps avoid similar errors. We can't call
ixgbe_ptp_stop, since it will free the PTP clock device, which we
shouldn't be doing during a suspend path.

Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:11 -07:00
Jacob Keller
9966d1ee6d ixgbe: separate the PTP suspend and stop actions
Since we are adding proper support for suspend of PTP, extract out of
ixgbe_ptp_stop those things relevant to suspend. Then, have
ixgbe_ptp_stop call ixgbe_ptp_suspend. The next patch in the series will
have ixgbe_ptp_suspend called from the ixgbe_suspend path.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:11 -07:00
Jacob Keller
63328ada9e ixgbe: extract PTP clock device from ptp_init
In order to properly handle a suspend/resume cycle, we cannot destroy
the PTP clock device. As part of this, we should only re-create the
device on first initialization. After a resume, when ixgbe_ptp_init is
called, we won't create a new clock, and we will use the old clock
device. To that end, this patch extracts the clock creation out of
ptp_init, and only calls it if we don't already have a ptp_clock
pointer.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:10 -07:00
Jacob Keller
d63214079f ixgbe: allow ixgbe_ptp_reset to maintain current hwtstamp config
Rather than clearing the hwtstamp configuration, we should use the known
configuration requested by the user and call the function which has now
been separated from the ioctl. This means that after a reset, the
timestamp mode will be maintained rather than lost. We still can't
maintain the clock value, however.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:10 -07:00
Jacob Keller
a7ef428636 ixgbe: extract the hardware setup from the ixgbe_ptp_set_ts_config
Currently all of the hardware setup logic for the PTP hardware bits is
buried inside of the ioctl which sets the timestamp configuration. This
makes it hard to use this logic in other places (primarily reset), and
this means we can't restore current timestamp mode upon a MAC reset.
Extracting this logic into a separate function will enable future work
for the ixgbe_ptp_reset function.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:10 -07:00
Jacob Keller
04c8de8e92 ixgbe: rename ixgbe_ptp_enable to ixgbe_ptp_feature_enable
Since the name ixgbe_ptp_enable could be misconstrued as a function
which enables the whole PTP core, rename this function so that it is
clear the function is for enabling of the extra features such as PPS
signal.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:09 -07:00
Emil Tantilov
d1a35ee277 ixgbe: fix linking at 100Mbps on copper devices with MNG FW enabled
Driver was calling setup_link to make sure that fiber interfaces with MNG FW
enabled will get link on probe because the laser was most likely turned off.
This prevented non-fiber devices with MNG FW from linking at 100Mbps.

This patch adds a check to only call setup_link for fiber devices.

Reported-and-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-26 23:53:09 -07:00
Prashant Sreedharan
506724c463 tg3: Override clock, link aware and link idle mode during NVRAM dump
When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.

Also decrease the NVRAM command execution timeout value to 1ms.

Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 23:39:50 -04:00
Yang Wei
cab6715c3e net: driver: stmicro: Remove some useless the lock protection
kernel always invokes a pair of rtnl_lock adn rtnl_unlock to
protect dev_ethtool(), so its not neccessary to invoke spin_lock/unlock
in ethtool_ops.

Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 23:32:53 -04:00
Stephen Boyd
f4c6e06dec net: ks8851: Add of match table
Users are currently just providing "ks8851" as the compatible for
this driver in device tree. Add a compatible string that provides
the vendor name along with the device name to be more explicit.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 14:03:21 -04:00
Stephen Boyd
73fdeb82e9 net: ks8851: Add optional vdd_io regulator and reset gpio
Allow the ks8851 driver to enable an optional 1.8V vdd_io
regulator and assert the reset pin to the phy if a reset gpio is
present in device tree.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 14:03:21 -04:00
Stephen Boyd
c78dbad8c4 net: ks8851: Use devm_regulator_get_optional()
This simplifies error paths and removes the need to
regulator_put().

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 14:03:21 -04:00
Dan Carpenter
7df566bbdd qlcnic: info leak in qlcnic_dcb_peer_app_info()
This function is called from dcbnl_build_peer_app().  The "info"
struct isn't initialized at all so we disclose 2 bytes of uninitialized
stack data.  We should clear it before passing it to the user.

Fixes: 48365e4852 ('qlcnic: dcb: Add support for CEE Netlink interface.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 14:01:17 -04:00
David S. Miller
54e5c4def0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/bonding/bond_alb.c
	drivers/net/ethernet/altera/altera_msgdma.c
	drivers/net/ethernet/altera/altera_sgdma.c
	net/ipv6/xfrm6_output.c

Several cases of overlapping changes.

The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.

In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.

Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 00:32:30 -04:00
David S. Miller
0c3592b821 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb, igbvf, ixgbe, i40e and i40evf.

Jacob provides eight patches to cleanup the ixgbe driver to resolve various
checkpatch.pl warnings/errors as well as minor coding style issues.

Stephen Hemminger and I provide simple cleanups of void functions which
had useless return statements at the end of the function which are not
needed.

v2: Dropped Emil's patch "ixgbe: fix the detection of SFP+ capable interfaces"
    while I wait for his updated patch to be validated.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 16:28:18 -04:00
Ezequiel Garcia
dc03e21a54 net: mvneta: Remove unneeded 'weigth' field
The 'weight' field is only used to pass the weigth to napi initialization
function. This commit removes the field, and instead uses a fixed value to
initialize the napi context.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
56ecd2cc38 net: mvmdio: Use devm_* API to simplify the code
This commit makes use of devm_kmalloc_array() for memory allocation and the
recently introduced devm_mdiobus_alloc() API to simplify driver's code.
While here, remove a redundant out of memory error message.

Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
edadb7fad3 net: mvneta: Change the number of default rx queues to one
The driver does not support multiple rx queues, and so it's a waste
of resources to have a default number larger than one (1).

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
e68de36072 net: mvneta: Use prepare/commit API to simplify MAC address setting
Use eth_prepare_mac_addr_change and eth_commit_mac_addr_change, instead
of manually checking and storing the MAC address, which makes the
code slightly more robust. This fixes the lack of valid MAC address check
in the driver's .ndo_set_mac_address hook.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
9672850be3 net: mvneta: Clean-up mvneta_init()
This commit cleans-up mvneta_init(), which initializes the hardware
and allocates the rx/qx queues. The queue allocation is simplified
by using devm_kcalloc instead of kzalloc. The unused phy_addr parameter
is removed. While here, the 'hal' references in the comments are removed.
This commit makes no functionality change.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
a92dbd9627 net: mvneta: Check tx queue setup error in mvneta_change_mtu()
This commit checks the return code of mvneta_setup_txq() call
in mvneta_change_mtu(). Also, use the netdevice pointer directly
instead of dereferencing the port structure. While here, let's
fix a tiny comment typo.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:49 -04:00
Ezequiel Garcia
3d4ea02fd8 net: mvneta: Clean-up mvneta_tx_frag_process()
A tiny clean-up to improve readability. This commit makes no functionality
change.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:48 -04:00
Ezequiel Garcia
0a9e413b44 net: mv643xx_eth: Simplify mv643xx_eth_adjust_link()
Currently, mv643xx_eth_adjust_link() is only used to call mv643xx_adjust_pscr().
This commit renames the latter to the former, and therefore removes the extra
and useless function.

Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:31:48 -04:00
Sucheta Chakraborty
ed616689a3 net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool.
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:04:02 -04:00
Stephen Hemminger
41457f64da i40e,igb,ixgbe: remove usless return statements
Remove cases where useless bare return is left at end of function.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-23 05:28:46 -07:00
Jeff Kirsher
c43f856cc9 igb/ixgbe: remove return statements for void functions
Remove useless return statements for void functions which do not need
it.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
2014-05-23 05:28:41 -07:00
Jacob Keller
3bf2379a2f ixgbe: add /* fallthrough */ comment to case statements
This semicomplex switch-case has various fallthrough portions, that were
not indicated by a /* fallthrough */ comment.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-23 05:28:30 -07:00
Jacob Keller
8105ecdf3a ixgbe: add space between operands to &
This patch cleans up a checkpatch.pl style warning in the ixgbe code.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-05-23 05:28:27 -07:00