Alex writes:
Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix dig encoder selection on DCE61
drm/radeon: fix double free in radeon_gpu_reset
drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
drm/radeon: rework panel mode setup
drm/radeon/atom: powergating fixes for DCE6
drm/radeon/atom: rework DIG modesetting on DCE3+
drm/radeon: don't disable plls that are in use by other crtcs
drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
drm/radeon: initialize tracked CS state
drm/radeon: fix reading CB_COLORn_MASK from the CS
[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]
This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver. It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board. Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
radeon_ring_restore is freeing the memory for the saved
ring data. We need to remember that, otherwise we try to
restore the ring data again on the next try. Additional
to that it shouldn't try the reset infinitely if we have
saved ring data.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It seems some of those IGP dislike non dma32 page despite what
documentation says. Fix regression since we allowed non dma32
pages. It seems it only affect some revision of those IGP chips
as we don't know which one just force dma32 for all of them.
https://bugzilla.redhat.com/show_bug.cgi?id=785375
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the panel mode setup to match the behavior
of the vbios. Rather than checking for specific
bridge chip ids, just check the eDP configuration register.
This saves extra aux transactions and works across
DP bridge chips without requiring additional per chip
id checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The ordering is important and the current drm code
wasn't cutting it for modern DIG encoders. We need
to have information about crtc before setting up
the encoders so I've shifted the ordering a bit.
Probably we'll need a full rework akin to danvet's
recent intel patchs. This patch fixes numerous
issues with DP bridge chips and makes link training
much more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Checking of the second colorbuffer was skipped on r700, because
CB_TARGET_MASK was 0xf. With r600, CB_TARGET_MASK is changed to 0xff,
so we must set the number of samples of the second colorbuffer to 1 in order
to pass the CS checker.
The DRM version is bumped, because RESOLVE_BOX is always rejected without this
fix on r600.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should help catch uninitialized registers and reject commands
because of that.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel writes:
"Just a few smaller things:
- Fix up a pipe vs. plane confusion from a refactoring, fixes a regression
from 3.1 (Anhua Xu).
- Fix ivb sprite pixel formats (Vijay).
- Fixup ppgtt pde placement for machines where the Bios artifically limits
the availbale gtt space in the name of ... product differentiation
(Chris). This fixes an oops.
- Yet another no_lvds quirk entry."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
drm/i915: Use the correct size of the GTT for placing the per-process entries
drm/i915: fix color order for BGR formats on IVB
drm/i915: fix wrong order of parameters in port checking functions
Ben says its just a single fix to avoid the wrong pcopy units being used.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
On some Fermi chipsets (NVCE particularly) PCOPY1 doesn't exist. And if
what I've seen on Kepler is true of Fermi too, chipsets of the same type
can have different PCOPY units available.
This should fix a v3.5 regression reported by a number of people effecting
suspend/resume on NVC8/NVCE chipsets.
Cc: stable@vger.kernel.org [3.5]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This board is incorrectly detected as having an LVDS connector,
resulting in the VGA output (the only available output on the board)
showing the console only in the top-left 1024x768 pixels, and an extra
LVDS connector appearing in X.
It's a desktop Mini-ITX board using an Atom D525 CPU with an NM10
chipset.
I've had this board for about a year, but this is the first time I
noticed the issue because I've been running it headless for most of its
life.
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
The current layout is to place the per-process tables at the end of the
GTT. However, this is currently using a hardcoded maximum size for the GTT
and not taking in account limitations imposed by the BIOS. Use the value
for the total number of entries allocated in the table as provided by
the configuration registers.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Matthew Garret <mjg@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is already fixed for ILK and SNB in the below commit but somehow
IVB is missed.
commit ab2f9df10d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Mon Feb 27 12:40:10 2012 -0800
drm/i915: fix color order for BGR formats on SNB
Had the wrong bits and field definitions.
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrong order of parameters passed-in when calling hdmi/adpa
/lvds_pipe_enabled(), 2nd and 3rd parameters are reversed.
This bug was indroduced by
commit 1519b9956e
Author: Keith Packard <keithp@keithp.com>
Date: Sat Aug 6 10:35:34 2011 -0700
drm/i915: Fix PCH port pipe select in CPT disable paths
The reachable tag for this commit is v3.1-rc1-3-g1519b99
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44876
Tested-by: Daniel Schroeder <sec@dschroeder.info>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Intel: edid fixes, power consumption fix, s/r fix, haswell fix
Radeon: BIOS loading fixes for UEFI and Thunderbolt machines, better
MSAA validation, lockup timeout fixes, modesetting fixes
One udl dpms fix, one vmwgfx fix, a couple of trivial core changes.
There is an export added to ACPI as part of the radeon bios fixes.
I've also included the fbcon flashing cursor vs deinit race fix, that
seems the simplest place to start"
Trivial conflict in drivers/video/console/fbcon.c due to me having
already applied the fbcon flashing cursor vs deinit race fix, and Dave
had added a comment in there too.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
fbcon: fix race condition between console lock and cursor timer (v1.1)
drm: Add missing static storage class specifiers in drm_proc.c file
drm/udl: dpms off the crtc when disabled.
drm: Remove two unused fields from struct drm_display_mode
drm: stop vmgfx driver explosion
drm/radeon/ss: use num_crtc rather than hardcoded 6
Revert "drm/radeon: fix bo creation retry path"
drm/i915: use hsw rps tuning values everywhere on gen6+
drm/radeon: split ATRM support out from the ATPX handler (v3)
drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
ACPI: export symbol acpi_get_table_with_size
drm/radeon: implement ACPI VFCT vbios fetch (v3)
drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
drm/radeon: fix checking of MSAA renderbuffers on r600-r700
drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
drm/radeon: init lockup timeout on ring init
drm/radeon: avoid turning off spread spectrum for used pll
drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
drm/i915: extract connector update from intel_ddc_get_modes() for reuse
drm/i915: fix hsw uncached pte
...
Fixes the following sparse warning:
drivers/gpu/drm/drm_proc.c:92:5:
warning: symbol 'drm_proc_create_files' was not declared. Should it be static?
drivers/gpu/drm/drm_proc.c:175:5:
warning: symbol 'drm_proc_remove_files' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This turns off the crtc when its been disabled,
fixes it not turning off properly the whole time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
If you do a page flip with no flags set then event is NULL. If event is
NULL then the vmw_gfx driver likes to go digging into NULL and extracts
NULL->base.file_priv.
On a modern kernel with NULL mapping protection it's just another oops,
without it there are some "intriguing" possibilities.
What it should do is an open question but that for the driver owners to
sort out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
" Nothing too major:
- A few fixes around the edid handling from Jani, also fixing a regression
in 3.5 due to us using gmbus by default.
- Fixup hsw uncached pte flags.
- Fix suspend/resume crash when using hw contexts, from Ben.
- Try to tune gpu turbo a bit better, seems to help with some oddball
power regressions."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: use hsw rps tuning values everywhere on gen6+
drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
drm/i915: extract connector update from intel_ddc_get_modes() for reuse
drm/i915: fix hsw uncached pte
drm/i915/contexts: fix list corruption
drm/i915: fix EDID memory leak in SDVO
This reverts commit d1c7871ddb.
ttm_bo_init() destroys the BO on failure. So this patch makes
the retry path work with freed memory. This ends up causing
kernel panics when this path is hit.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAyjj4ACgkQMUfUDdst+yn8gQCgkNpc92Ux5hBYJIX/AQYoBrTB
ktAAoLiXxIhVP+D4C42R1VLw9vGeB1QH
=+8kb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB patches from Greg Kroah-Hartman:
"Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
gpu/mfd/usb: Fix USB randconfig problems
USB: CDC ACM: Fix NULL pointer dereference
USB: emi62: remove __devinit* from the struct usb_device_id table
USB: winbond: remove __devinit* from the struct usb_device_id table
USB: vt6656: remove __devinit* from the struct usb_device_id table
USB: rtl8187: remove __devinit* from the struct usb_device_id table
USB: p54usb: remove __devinit* from the struct usb_device_id table
USB: spca506: remove __devinit* from the struct usb_device_id table
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
USB: smsusb: remove __devinit* from the struct usb_device_id table
Fix config warning:
warning: ( ... && DRM_USB) selects USB which has unmet direct dependencies
(USB_SUPPORT && USB_ARCH_HAS_HCD)
and build error:
ERROR: "usb_speed_string" [drivers/usb/core/usbcore.ko] undefined!
by adding the missing dependency on USB_ARCH_HAS_HCD to DRM_UDL and DRM_USB.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:16: symbol USB_ARCH_HAS_OHCI depends on I2C
drivers/i2c/Kconfig:5: symbol I2C is selected by FB_DDC
drivers/video/Kconfig:86: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/Kconfig:385: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/Kconfig:373: symbol FB_CYBER2000 depends on FB
which is due to drivers/usb/Kconfig:
config USB_ARCH_HAS_OHCI
...
default y if ARCH_PNX4008 && I2C
Fix by dropping I2C from the above dependency; logic is that this is not a
platform dependency but a configuration dependency: the _architecture_ still
supports USB even is I2C is not selected.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:17: symbol USB_ARCH_HAS_OHCI depends on MFD_TC6393XB
drivers/mfd/Kconfig:396: symbol MFD_TC6393XB depends on GPIOLIB
drivers/gpio/Kconfig:35: symbol GPIOLIB is selected by FB_VIA
drivers/video/Kconfig:1560: symbol FB_VIA depends on FB
which can be fixed by having MFD_TC6393XB select GPIOLIB instead of depending on
it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley reported [1] a massive power regression, due to the
enabling of semaphores by default in 3.5. A workaround for him is to
again disable semaphores. And indeed, his system has a very hard time
to enter rc6 with semaphores enabled.
Ben Widawsky run around with a kill-a-watt a lot and noticed:
- There are indeed a few rare systems that seem to have a hard time
entering rc6 when desktop-idle.
- One machine, The Indestructible Toshiba regressed in this behaviour
between 3.5 and 3.6 in a merge commit! So rc6 behaviour with the
current setting seems to be highly timing dependent and not robust
at all.
- The behaviour James reported wrt semaphores seems to be a freak
timing thing that only happens on his specific machine, confirming
that enabling semaphores shouldn't reduce rc6 residency.
Now furthermore the Google ChromeOS guys reported [2] a while ago that
at least on some machines a simply a blinking cursor can keep the gpu
turbo at the highest frequency. This is because the current rps limits
used on snb/ivb are highly asymmetric.
On the theory that gpu turbo and rc6 tuning values are related, we've
tried whether the much saner looking (since much less asymmetric) rps
tuning values used for hsw would also help entering rc6 more robustly.
And it seems to mostly work, and we don't really have the resources to
through-roughly tune things in any better way: The values from the
ChromeOS ppl seem to fare a bit worse for James' machine, so I guess
we better stick with something vpg (the gpu hw/windows group)
provided, hoping that they've done their jobs.
Reference[1]: http://lists.freedesktop.org/archives/dri-devel/2012-July/025675.html
Reference[2]: http://lists.freedesktop.org/archives/intel-gfx/2012-July/018692.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53393
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required for pure UEFI systems. The vbios is stored
in ACPI rather than at the legacy vga location.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=26891
V2: fix #ifdefs as per Greg's comments
V3: fix it harder
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
There is a more recent APU stepping with a new PCI ID
shipping in the same board by Fujitsu which needs the
same quirk to correctly mark the back plane connectors.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The MSAA checking was mostly unimplemented on r600-r700. The userspace
submits GPU commands and the kernel driver computes how much memory
the GPU will access and checks if it's all within buffer bounds the
userspace allocated. This patch fixes the computations of the size of
MSAA surfaces in memory.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MSAA is impossible without them.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reset the lockup timeout on ring (re-)initialisation.
Otherwise we get error messages like this on gpu resets:
[ 1559.949177] radeon 0000:01:00.0: GPU lockup CP stall for more than 1482270msec
Signed-off-by: Christian König <deathsimple@vodafone.de>
cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
If spread spectrum is enabled and in use for a given pll we
should not turn it off as it will lead to turning off display
for crtc that use the pll (this behavior was observed on chelsea
edp).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This callback is a no-op in nouveau, and the upcoming apple-gmux
switcheroo support won't require it either. Rather than forcing drivers
to stub it out, just make it optional and remove the callback from
nouveau.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
GMBUS was enabled over bit-banging as the default in commits:
commit c3dfefa0a6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Feb 14 22:37:25 2012 +0100
drm/i915: reenable gmbus on gen3+ again
and
commit 0fb3f969c8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Mar 2 19:38:30 2012 +0100
drm/i915: enable gmbus on gen2
Unfortunately, GMBUS seems to fail on some CRT displays. Add a bit-banging
fallback to CRT EDID reads.
LKML-Reference: <201207251020.47637.maciej.rutecki@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45881
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Alex Ferrando <alferpal@gmail.com>
Cc: stable@vger.kernel.org (for 3.4+3.5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the connector update part of intel_ddc_get_modes() into a separate
intel_connector_update_modes() function for reuse. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45881
Tested-by: Alex Ferrando <alferpal@gmail.com>
Cc: stable@vger.kernel.org (for 3.4+3.5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They've changed it ... for no apparent reason. Meh.
V2: remove unused 'is_hsw' field.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After reset we unconditionally reinitialize lists. If the context switch
hasn't yet completed before the suspend, the default context object will
end up on lists that are going to go away when we resume.
The patch forces the context switch to be synchronous before suspend
assuring that the active/inactive tracking is correct at the time of
resume.
References: https://bugs.freedesktop.org/show_bug.cgi?id=52429
Tested-by: Guang A Yang <guang.a.yang@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The EDID returned by drm_get_edid() was never freed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.
Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:
commit 6c6cf5aa9c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 20 18:02:28 2012 +0100
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671
Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fix is a backport from the reworked nouveau driver. It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The copy engine exhibits random memory corruption in at least one case, the
GeForce 320M (nv50, 0xaf) in the MacBookAir3,1.
This patch omits creating the engine for the specific chipset, falling back
to M2MF, which kills the symptoms.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes screen being black after changing performance level.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.5+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
In any case, this patch is necessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the checking seems to be in place already. As you can see,
log2(number of samples) resides in LAST_LEVEL.
This is required for MSAA support (namely for depth-stencil resolve and
blitting between MSAA resources).
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
This patch should also fix :
https://bugs.freedesktop.org/show_bug.cgi?id=42373
Cc: <stable@vger.kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
The sixteen bank case wasn't handled here, leading to GPU
crashes because of userspace miscalculation.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The IntegratedSystemInfo table changed versions
on TN. Update the SS override lookup to handle it.
v2: fix copy-paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set a more reasonable default cursor watermark. The
recommended default value is 4. This should reduce
urgency requests to the MC form the display hw.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This has originally been introduced to not oversubscribe the dp links
in
commit 885a5fb5b1
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Tue Jan 12 05:38:31 2010 +0800
drm/i915: fix pixel color depth setting on eDP
Since then we've fixed up the dp link bandwidth calculation code and
should now automatically fall back to 6bpc dithering. So this is
unnecessary.
Furthermore it seems to break the new MacbookPro with retina display,
hence let's just rip this out.
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Francois Rigaut <frigaut@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Tested-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Bernhard Froemel <froemel at vmars tuwien.ac.at>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
--
Testing feedback highgly welcome, and thanks for Benoit for finding
out that the bpc computations are busted.
-Daniel
When you reopen the lid on a laptop with PCH, the panel suddenly goes
blank sometimes. It seems because BLC_PWM_CPU_CTL register is cleared
to zero when BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1 registers are
enabled.
This patch fixes the problem by moving the call of the function setting
BLC_PWM_CPU_CTL after enabling other two registers.
Reported-and-tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The original code was misported from the X driver,
a) an int went to unsigned int, breaking the downward counting testm code
b) the port did the vco/computed clock bits completely wrong.
This fixes an infinite loop on modprobe on some Dell servers with the G200ER
chipset variant.
Found in internal testing.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Do not leak memory by updating pointer with potentially
NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The semantic patch that makes this change is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
"- Regression fixer for an OOPS at boot when i915.ko is built-in and
CONFIG_PM=n, introduce in 3.5 (patch from Hunt Xu)
- Regression fixer for occlusion query failures, the required w/a wasn't
applied in all cases (thanks to Eric for tracking this on down).
- dmar vs. dma_buf imprt fix (Dave Airlie)
- 2 patches to fight down forcewake issues on snb. This is the stuff I've
talked about 2 weeks ago already, it's a minefield. Investigation still
going on, but afaict this is the best we have for now.
- a few minor things to keep coverty&compiler happy (Alan, Davendra,
Stéphane)
- tons of hsw pci ids - this one is a bit late because internal approval
sometimes takes a while, but ppl in charge finally agreed that world+dog
already knows about ult and crw haswell variants ;-)
Wrt regressions I'm aware of:
- the power regression due to semaphores=1. Ben is running around with a
killawatt, unfortunately we have a hard time reproducing this one. And
this /shouldn't/ increase power usage. Ben has turned up a few odds bits
though already.
- the lvds fix in 3.6-rc1 broke a backlight after lid close/open (but can
be resurrected with a modeset cycle). I guess we anger the bios - I'm
still looking into this one.
- gmbus broke edid reading on an odd-ball monitor, we need to fall-back.
Due to vacation (both mine&the reporter's) this is stalling for a final
patch and a tested-by on it. But issue is fully diagnosed."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: correctly order the ring init sequence
drm/i915: add more Haswell PCI IDs
drm/i915: make rc6 in sysfs functions conditional
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
drm/i915: Make intel_panel_get_backlight static.
i915: don't map imported dma-bufs for dmar.
drm/i915: remove unused variable
drm/i915: Don't forget to apply SNB PIPE_CONTROL GTT workaround.
drm/i915: fix forcewake related hangs on snb
i915: Remove silly test
i915: fix error path leak in intel_sdvo_write_cmd
vlv: it might be wise if we initialised the flag value...
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We may only start to set up the new register values after having
confirmed that the ring is truely off. Otherwise the hw might lose the
newly written register values. This is caught later on in the init
sequence, when we check whether the register writes have stuck.
Cc: stable@vger.kernel.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522
Tested-by: Yang Guang <guang.a.yang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also properly indent the HB IDs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 0136db586c merges rc6 information
into the power group. However, when compiled with CONFIG_PM not set,
modprobing i915 would taint since power_group_name is defined as NULL.
This patch makes these rc6 in sysfs functions conditional upon the
definition of the CONFIG_PM macro to avoid the above-mentioned problem.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45181
Cc: stable@vger.kernel.org
Tested-by: Kris Karas <bugs-a12@moonlit-rail.com>
Signed-off-by: Hunt Xu <mhuntxu@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reasons that are not apparent to anybody, 990bbdadab (drm/i915:
Group the GT routines together in both code and vtable) breaks the use
of the BitStream Decoder ring on SandyBridge. The active ingredient of
that patch is the conversion from a udelay(10) to a udelay(1) in the
busy-wait loop of waiting for the forcewake acknowledge. If we restore
that udelay(10) or insert another udelay(1) afterwards (or any wait
longer than 250ns) everything works again. An alternative is also to
remove any delay from the busy-wait loop.
Given that in the atomic sections we want to complete the wait as quick
as possible to avoid blocking the CPU for too long, it makes sense to
remove the delay altogether and simply spin on the exit condition until
it completes. So we replace the udelay(1) with cpu_relax().
Papers over regression from
commit 990bbdadab
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jul 2 11:51:02 2012 -0300
drm/i915: Group the GT routines together in both code and vtable
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function isn't used outside of intel_panel.c, so make it static.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The exporter should have given us pages in the correct place, avoid
the prepare object mapping phase on dmar systems.
This fixes an oops on a GM45/R600 machine, when running the intel/radeon
tests.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
the following warning was produced,
drivers/gpu/drm/i915/i915_gem_context.c: In function ‘i915_switch_context’:
drivers/gpu/drm/i915/i915_gem_context.c:454:6: warning: unused variable ‘ret’ [-Wunused-variable]
fix up by removing it
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a buffer that was the target of a PIPE_CONTROL from userland was a
reused one that hadn't been evicted which had not previously had this
workaround applied, then the early return for a correct
presumed_offset in this function meant we would not bind it into the
GTT and the write would land somewhere else.
Fixes reproducible failures with GL_EXT_timer_query usage in apitrace,
and I also expect it to fix the intermittent OQ issues on snb that
danvet's been working on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48019
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52932
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Carl Worth <cworth@cworth.org>
Tested-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull Exynos DRM changes from Dave Airlie:
"So I totally missed Inki's pull request for -next, its fully exynos
self contained."
(I took just the actual commits, not Dave's two extraneous merges)
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (30 commits)
drm/exynos: fixed exception to page allocation failure
drm/exynos: use __free_page() to deallocate memory
drm/exynos: fixed a comment to gem size.
drm/exynos: removed unnecessary variable
drm/exynos: do not release memory region from exporter.
drm/exynos: set buffer type from exporter.
drm/exynos: use alloc_page() to allocate pages.
drm/exynos: fixed build warning.
drm/exynos: fixed edid data setting at vidi connection request
drm/exynos: check if raw edid data is fake or not for test
drm/exynos: set edid fake data only for test.
drm/exynos: removed unnecessary declaration.
drm/exynos: fix buffer pitch calculation
drm/exynos: check for null in return value of dma_buf_map_attachment()
drm/exynos: return NULL if exynos_pages_to_sg fails
drm/exynos: Use devm_* functions in exynos_mixer.c
drm/exynos: Use devm_* functions in exynos_hdmi.c
drm/exynos: Use devm_* functions in exynos_drm_fimd.c
drm/exynos: Add missing static storage class specifier
drm/exynos: add property for crtc mode
...
... by adding seemingly redudant posting reads.
This little dragon lair exploded the first time around when we've
refactored the code a bit to use the common wait_for_atomic_us in
"drm/i915: Group the GT routines together in both code and vtable",
which caused QA to file fdo bug #51738.
Chris Wilson entertained a few approaches to fixing #51738: Replacing
the udelay(1) with the previously-used udelay(10) (or any other
"sufficiently larger" delay), adding a posting read, or ditching the
delay completely and using cpu_relax. We went with the cpu_relax and
"915: Workaround hang with BSD and forcewake on SandyBridge". Which
blew up in fdo bug #52424, but adding the posting read while still
using cpu_relax seems to also fix that, it looks like the
posting read is the important ingriedient to fix these rc6 related
hangs on snb.
Popular theories as to why this is like it is include:
- A herd of pink elephants got royally angered somehow.
- The gpu has internally different functional units and judging by the
register offsets, the forcewake request register and the forcewake
ack registers are _not_ in the same functional unit (or at least
aren't reached through the same routes). Hence the posting read
syncs up with the wrong block and gets the entire gpu confused.
- ...
As a minimal ducttape fix for 3.6, let's just put these posting reads
into place again. We can try fancier approaches (like adding back the
cpu_relax instead of the udelay) in -next.
This (re-)fixes a regression introduced in
commit 990bbdadab
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jul 2 11:51:02 2012 -0300
drm/i915: Group the GT routines together in both code and vtable
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Du Yan <yanx.du@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52424
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51738u
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
this patch corrects to deallocate the pages allocated already
at alloc_page failure.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
this patch uses __free_page() to deallocate the pages allocated
by alloc_page() and the pages doesn't need set_parge_dirty()
and mark_page_accessed() because they aren't from page cache so
removes them.
this patch has a pair with previous patch below,
http://www.spinics.net/lists/dri-devel/msg24382.html
Changelog v2:
remove unnecessary arguments.
Changelog v3:
fix npages type.
- npages can have negative value.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
the region should be released by exporter once dmabuf's refcount becomes 0.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
when fd is imported to gem, whether the memory type from exporter
is contigous or not should be set to gem flag so that drm-based
driver can aware of the memory type.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
shmem_read_mapping_page_gfp() first tries to allocate pages from page cache
so if pages are allocated from page cache then these pages could have
valid cache line. after that cpu may read garbage data from cache
once gpu operation is completed with allocated pages. so with this patch,
Non-contiguous memory allocation request allocates pages from highmem
through alloc_page() with GFP_HIGHUSER_MOVABLE.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
edid data from user should be allocated and copied into vidi context and also
freed with disconnection.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
if raw edid data isn't same as fake data then it can't be tested.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
