Re-organize the firmware handling code and declarations a bit to make
the code more compact.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change a long udelay() in bnx2_setup_copper_phy() to msleep().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to parallel detect 1Gbps and 2.5Gbps link speeds.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the 5706S SerDes handling code in bnx2_timer() and put it
in a new function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add support for 2.5Gbps forced speed setting.
2. Remove a long udelay() loop and change to msleep().
3. Other misc. SerDes fixes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the problem of not receiving packets in the Xen bridging
environment. The Xen script sets the device's MAC address to
FE:FF:FF:FF:FF:FF and puts the device in promiscuous mode. The
firmware had problem receiving all packets in this configuration.
New firmware and setting the PROM_VLAN bit when in promiscuous mode
will fix this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted by Ian McDonald, tentatively fixed by Gerrit Renker:
http://www.mail-archive.com/dccp%40vger.kernel.org/msg00599.html
Rewritten not to unroll sk_receive_skb, in the common case, i.e. no lock
debugging, its optimized away.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
The beast had a long and not very happy history. At one
point, a friend (netdump) had asked that he open up a little.
Well, the friend was long gone now, and the beast had
this dangling piece hanging (netpoll_queue).
It wasn't hard to stitch the netpoll_queue back in
where it belonged and make everything tidy.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The beast was not always healthy. When it was sick,
it tended to be laconic and not tell anyone the real problem.
A few small changes had it telling the world about its
problems, if they really wanted to hear.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This patch contains the scheduled removal of the frame diverter.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most PHYs connect to an ethernet controller over a GMII or MII
interface. However, a growing number are connected over
different interfaces, such as RGMII or SGMII.
The ethernet driver will tell the PHY what type of connection it
is by setting it manually, or passing it in through phy_connect
(or phy_attach).
Changes include:
* Updates to documentation
* Updates to PHY Lib consumers
* Changes to PHY Lib to add interface support
* Some minor changes to whitespace in phy.h
* gianfar driver now detects interface and passes appropriate
value to PHY Lib
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If transmit lock is contended on, then push return code back
and retry at higher level.
Bugfix: If buffer is reallocated because of lack of headroom
and the send is blocked, then drop packet. This is necessary
because caller would end up requeuing a freed skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup statistics management:
* Get rid of duplicate or unused statistics
* Convert high volume stats to per-cpu and 64 bit
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using MSI can avoid sharing IRQ and associated overhead.
Tested on PCI-X.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace driver crc calculation with existing library.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace macro with function for updating RMON values
Cleanups:
* remove unused enum's
* Fix comment format
Signed-off-by: Stephen HEmminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for other versions of the 10G Chelsio boards.
This is basically a port of the vendor driver with the
TOE features removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I noticed this driver (and several others) reinvent their own copy of the
existing CRC library. Don't have the hardware, but tested by extracting
code and comparing result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If using Message Signaled Interrupts (MSI) then the IRQ will never
be shared. Don't call pci_disable_msi() unless using MSI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is possible for the sky2 driver NAPI poll routine to be called with
IRQ's disabled if netpoll is trying to make space in the tx queue. This
is an obscure path, but if it happens, the kfree_skb needs to happen
via softirq. Calling kfree_skb with IRQ's disabled is a not allowed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update workarounds for 88E803X based on the latest SysKonnect vendor
driver version (8.41). Tested on EC_U rev A1, only.
These up the receive performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add new PCI ID for DLink 560SX.
This from the latest SysKonnect vendor driver (version 8.41).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If sky2 detects out of memory, or gets a bad frame, it reuses the same receive
buffer, but forgets to poke the hardware. This could lead to the receiver
getting stuck if there were lots of errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I would rather fix Andy's problem by not clearing
multicast information on link down.
Also, add code to restore multicast state after ethtool phy reset.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/built-in.o: In function `netxen_nic_remove':
netxen_nic_main.c:(.text+0x31b4d): undefined reference to `pci_disable_msi'
netxen_nic_main.c:(.text+0x31b8e): undefined reference to `pci_release_regions'
drivers/built-in.o: In function `netxen_init_module':
netxen_nic_main.c:(.init.text+0x3f17): undefined reference to `pci_module_init'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio driver can use __netif_rx_schedule_prep instead of it's own
test_and_set inline. Applies after the previous 4 patches.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Network devices need to be free'd with free_netdev() not kfree()
otherwise the kernel will panic if an application has /sys/class/net/ethX/value
open and reads it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Complete removal of proc stuff from chelsio. The orignal driver had a debug
proc interface, but not all the code got removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whitespace cleanups. Replace leading spaces with tabs and fix indentation
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio network driver has some extra ifdef's that got in because the
driver was originally based on code that worked on 2.4 as well as 2.6.
This patch removes the dead code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Include of_platform header, and use
new of_[un]register_platform_driver() fns.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use NULL instead of 0 for pointers (cures sparse warnings).
drivers/net/sundance.c:1106:16: warning: Using plain integer as NULL pointer
drivers/net/sundance.c:1652:16: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bcm43xx and ipw2100 currently duplicate the same simplistic get_stats
handler. Additionally, zd1211rw requires the same handler to fix a
bug where all stats are reported as 0.
This patch adds a generic implementation to the ieee80211 layer,
which drivers are free to override.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds zd1211rw driver support for the softmac functionality I
added a while back. We now obey changes in basic rates, use short
preamble if it is available (but long if the AP says it's not),
and send self-CTS in the proper situations.
Locking fixed and improved by Ulrich Kunitz.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These controlset rate constants are also applicable in places outside
the controlset, such as in the RTS/CTS control register.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Goff found that he could not use his ZD1211 device which is
programmed for the Japan regulatory domain. It turns out that ZyDAS
deviate from the spec here: they do not use the newer Japan region code
(0x41) but their drivers do operate as if the newer Japan legal
frequency range is in effect.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a high number of split USB transactions, which contain
only one packet but have a length info field. This patch optimizes
this code by stopping parsing the length info structure if a zero
length field is encountered.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit-field constants in zd_chip.h are now defined using a shift expression.
The value 0x08 is now (1 << 3). The fix is intended to improve readability.
Remove misleading comment in zd_mac.c: The function already returns -EPERM
in managed mode (IW_MODE_INFRA).
Remove unused code in zd_mac.c: The unused code intended for debugging
rx_status values is no longer useful.
Added dump_stack() to ZD_ASSERT macro: Output of the stack helps to debug
assertions. Keep in mind that the ZD_ASSERT() macro only results in code,
if DEBUG is defined.
Improved comments for filter_rx()
zd_usb.c: Added driver name to module init and exit functions
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
http://bugzilla.kernel.org/show_bug.cgi?id=7399
zd1211rw's support for IW_FREQ_AUTO is broken: when specified, the driver
tries to change to a channel specified in an uninitialized integer. As
IW_FREQ_AUTO is hard to implement properly, the solution (at least for now)
is to drop support for it and start ignoring the flags like all other wireless
drivers do.
This has the added advantage that kismet also starts working with zd1211rw,
even though kismet requesting IW_FREQ_AUTO is also a bug (fixed in their svn)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
