This converts the Nomadik pin controller and all associated device
trees to use the standard, generic config bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin controller and all associated device
trees to use the standard, generic mux bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the AB8500 muxing and biasing settings over from the board
file to the device tree, include it in the reference designs using
the AB8500: HREF prior to v60, v60plus and Snowball. Set up these
GPIO lines using hogs, just like in the board file.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC3589x devices appearing in the ST Ericsson device trees
are adjusted to use the new binding so this is in a good shape,
and we add the keypad on the TVK1281618 UIB so this is working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The BU21013 touchscreen GPIOs have been pretty confused, correct
them per board, and move the GPIO assignments up to the top
level DTS file so we can control it from there, and avoid defining
the GPIO assignments for non-ST UIB equipped boards.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:
- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
