On ISP83xx cards perform a fundamental reset instead of hot reset.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting this to 255 will cause any target with id 255 to not show up so leave
it at the default in our host template.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2xxx show wrong PCIe(2.5Gb/s x8) speed in the kerenel message. It should be
5.0Gb/s.
Signed-off-by: Atul Deshmukh <atul.deshmukh@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Stale information in the temporary fcport created in
qla2x00_configure_local_loop() causes qla2x00_get_port_database() call
to fail. This reschedules scan, which gets stuck continuously in the
rescheduling-of-scan loop due to the failure.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update the driver copyright from 2003-2011 to 2003-2012.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minor changes to support loopback functionality with ISP83xx CNAs.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Store used fcport loop_id's in a bitmap so that as opposed to looping through
all fcports to find the next free loop_id, new loop_id lookup can be just be
done via bitops.
[jejb: plus fix for incorrect LOOPID_MAP_SIZE from Andrew Vasquez]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The device limit of 128 tape drives was established in 2003 as a
significant increase from the 8 tape drives allowed previously.
We're seeing customer sites that between a large number of drives
and multipath are discovering more than 128 devices and running
into problems.
Now that we're not stuck having to store a pointer in array
and aren't limited by kmalloc failing on higher order allocs we can
lift the limit to fill the entire minor range based on the number
of modes.
Based on the current code, that's 2^17 devices.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch cleans up the st device file creation and removal.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
st currently allocates an array to store pointers to all of the
scsi_tape objects. It's used to discover available indexes to use as the
base for the minor number selection and later to look up scsi_tape
devices for character devices.
We switch to using an IDR for minor selection and a pointer from
st_modedef back to scsi_tape for the lookups.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
st_probe leaves a cdev pointer hanging around that is compared
during the error path and freed later. There's no need for the pointer
to hang around at all. So we free it immediately and simplify the error
handling.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
st currently sets up and tears down class attributes manually for
every tape drive in the system. This patch uses a statically defined
class with class attributes to let the device core do it for us.
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A TCP RST/FIN can be received even before the connection specific
structures are initialized.This fix checks for the conn structure
is intialized or not when RST/FIN is received.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for configuring the VLAN parameters on the adapter
using the iscsiadm interface.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The MAC_ADDR stored in driver private structure is of
unsigned char data type but strlcpy parameters is of
signed char data type. This conversion of data types
lead to change in the value.This changed value is passed
to the upper layer and junk characters were displayed
when "iscsiadm -m iface" command was run.
In case of iSCSI boot, since the the MAC_ADDR was coming
junk the boot was also not working
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new log level mechanism for different events. These
log levels can be set at driver load time/run time. The
log level is set for each Scsi_host.
Fixed few multi-line print warning to get over the new checkpatch.pl
warnings on multi-line strings.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the driver comes up in crashdump mode, it has to explicitly
issue command to FW for logging to the boot target. This fix issues
MBX Cmd to login to boot target in crashdump mode.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The setting of iscsi_data_pdu is not required anymore,
as this was required for BE1 adapters only. The BE1 adapter
were not supported in any previous versions of the kernel.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make compliant with FC specs by sending LOGO after ABTS timeouts
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
FC and iSCSI class set SCSI devices to transport-offline state after
fast_io_fail/replacement_timeout has fired, but after relogin, function
scsi_internal_device_unblock() is not setting scsi device state to running.
Due to this the devices even after being relogged in remain offline.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The current code would incorrectly return a DID_OK for a
CHECK CONDITION with Recovered error sense key causing incorrect
completion of a command when there is a dropped frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During iscsid session recovery driver sends multiple ISCSI_CONN_STATE_LOGGED_IN
event from qla4xxx_conn_start() and qla4xxx_ddb_change(), which causes iscsid
to crash.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In qla4xxx_ep_connect(), qla_ep->dst_addr and dst_addr are type
struct sockaddr. We are copying sizeof(struct sockaddr_in6) bytes
from dst_addr to qla_ep->dst_addr which is 12 bytes larger. This
will cause memory corruption. So we change qla_ep->dst_addr to
struct sockaddr_storage which is of 128 byte, large enough to
hold sizeof(struct sockaddr_in6).
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add fcp_io_channel module attribute to control amount of parallel I/O queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commonize SLI-3/4 Ring/Queue framework, to keep SLI-3 compatibility
Parallelize SLI-4 Q distribution - to use multiple posting/completion queues
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
"rc" is always zero here, so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We recently changed the locking in this function, but this return was
missed. It needs an unlock and the IRQs need to be restored.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Without this patch, scsi_show_result prints hostbyte as invalid for statuses
that are not defined in hostbyte_table (when scsi logging is enabled).
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
I think ioremap() ends up being equivalent to ioremap_nocache
by default, but we should signal our intent that these mappings
should be non-cacheable.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the abort handler, when asked to abort a command which
is not known to the driver, SUCCESS is returned, but the
diagnostic message incorrectly indicates the abort failed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It turns out Smart Array logical drives do not support target
reset and when the target reset fails, the logical drive will
be taken off line. Symptoms look like this:
hpsa 0000:03:00.0: Abort request on C1:B0:T0:L0
hpsa 0000:03:00.0: resetting device 1:0:0:0
hpsa 0000:03:00.0: cp ffff880037c56000 is reported invalid (probably means target device no longer present)
hpsa 0000:03:00.0: resetting device failed.
sd 1:0:0:0: Device offlined - not ready after error recovery
sd 1:0:0:0: rejecting I/O to offline device
EXT3-fs error (device sdb1): read_block_bitmap:
LUN reset is supported though, and is what we should be using.
Target reset is also disruptive in shared SAS situations,
for example, an external MSA1210m which does support target
reset attached to Smart Arrays in multiple hosts -- a target
reset from one host is disruptive to other hosts as all LUNs
on the target will be reset and will abort all outstanding i/os
back to all the attached hosts. So we should use LUN reset,
not target reset.
Tested this with Smart Array logical drives and with tape drives.
Not sure how this bug survived since 2009, except it must be very
rare for a Smart Array to require more than 30s to complete a request.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the wait time in seconds after I/O timeout before
resetting the adapter.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the queue depth of the adapter when throttled due
to I/O timeout.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reduce the amount of time the host lock is held in the interrupt handler
for improved performance.
[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reduce the amount of time the host lock is held in queuecommand
for improved performance.
[jejb: fix up checkpatch noise]
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When device discovery is disabled during driver load time using module
parameter "disable_discovery=1" and when diag reset is issued then from logs,
it is observed that the devices get added, removed and then added with new
target ids.
So, in order to limit this turn-off the code which is deleting and devices
across host reset when the disable_discovery module parameter is turned on.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch provides a command line option to disable "Port enable" during
the driver load.
The objective of this command line option is to load the driver and do
all the necessary initialization excluding port enable(i.e. delay
device discovery)
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changeset in MPI 2.0 Rev V(2.0.14) specification
1) Bumped MPI2_HEADER_VERSION_UNIT.
2) Added a product specific range to event values.
3) Added clarification to Direct-Attached SAS PHY Power condition.
4) Updated timing requirements for performing Hard Reset.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
