This update allows to have a clearer fps log trace by adding information
about plane size and plane pixel format.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Do not process update requests with unmodified parameters.
Since the HQVDP command queue is limited to 2, we shall take care of
not posting unneeded commands, which would abusively fill the command
queue leading to frame update skip.
This typically happens when the driver is called with legacy
(non-atomic) IOCTL : in that case atomic_update() is called multiple
times with the same parameters.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
When a plane is enabled, after having been disabled, do not reload XP70
firmware again, but only register VTG again
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
This fix allows to play audio while HDMI is disconnected.
When HDMI is disable, audio configuration is stored and samples
are dropped (by HDMI IP).
When HDMI is enabled, audio HDMI configuration is applied and samples
are outputted on HDMI wire.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
* pm-domains:
PM / domains: Fix 'may be used uninitialized' build warning
* pm-docs:
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
* pm-devfreq:
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
* pm-cpufreq:
cpufreq: dt: Add support for APM X-Gene 2
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Some SoC without MMU have display driver where a drm/kms driver
could be implemented.
Before doing such kind of thing drm/kms must allow to use mmuless devices.
This patch propose to remove MMU configuration flag and add a cma helper
function to help implementing mmuless display driver
version 4:
- add documentation about drm_gem_cma_get_unmapped_area()
- stub it MMU case
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
[danvet: Use recommended struct member references in kernel-doc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483521177-21794-4-git-send-email-benjamin.gaignard@linaro.org
drm_vm.c functions are only need for DRM_LEGACY and DRM_NOUVEAU.
Use a new DRM_VM to define when drm_vm.c in needed.
stub drm_legacy_vma_flush() to avoid compilation issues
version 4:
- a "config DRM_VM" in Kconfig
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
[danvet: Fix conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow generic frame-buffer to provide a default
get_fb_unmapped_area function if specific devices need it.
Usually this function is defined in architecture directories but
define it here may limit code duplication especially for all ARM
platforms without MMU.
version 5:
- set get_unmapped_area field if FB_PROVIDE_GET_FB_UNMAPPED_AREA is
defined
version 4:
- introdude a configuration flag to be independent of architecture
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483521177-21794-2-git-send-email-benjamin.gaignard@linaro.org
The following commit:
8196dab4fc ("x86/cpu: Get rid of compute_unit_id")
... broke the initial strategy for Bulldozer-based cores' topology,
where we consider each thread of a compute unit a standalone core
and not a HT or SMT thread.
Revert to the firmware-supplied core_id numbering and do not make
them thread siblings as we don't consider them for such even if they
technically are, more or less.
Reported-and-tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # v4.6+
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 8196dab4fc ("x86/cpu: Get rid of compute_unit_id")
Link: http://lkml.kernel.org/r/20170105092638.5247-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
fujitsu-laptop:
- use brightness_set_blocking for LED-setting callbacks
platform/x86: fix surface3_button build errors:
- fix surface3_button build errors
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYbxSIAAoJEKbMaAwKp364UOcIAJ6GVrHc2RiQDO+jJyNZyPaZ
fZe8k2PC3C9hJwOcIbxsEcaJxbAs34RM87mpmKSodYyyGCTw7HDOHPuxdB67Aisx
atjdBFbG6gjdW5jjtYzwfq2FD+PhEBWRiXbfaX4yMIJu1tEUfhUvYv4PMSpUSEFH
mqECMEzHZHKzNoroceA5Tekk0L+Z7wjJDaw0ePA5zPYU6CC6Z9O/j1JF/zhdn9OL
/+/tIB+K9eO7TQT8nTLCzCwapODGHYgD5HEz+orKeOL1fXknktvhfmhjjEHudtU4
egJ/c0IsAoIIymkuikP61uGhoKGUqJwjNeoctlSz8cTeBaaq63tvT6NZH7XdkCY=
=wCRj
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for platform drivers x86:
- use brightness_set_blocking for LED-setting callbacks on Fujitsu
laptops
- fix surface3_button build errors"
* tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: use brightness_set_blocking for LED-setting callbacks
platform/x86: fix surface3_button build errors
Pull audit fixes from Paul Moore:
"Two small fixes relating to audit's use of fsnotify.
The first patch plugs a leak and the second fixes some lock
shenanigans. The patches are small and I banged on this for an
afternoon with our testsuite and didn't see anything odd"
* 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit:
audit: Fix sleep in atomic
fsnotify: Remove fsnotify_duplicate_mark()
The device_unregister call in thermal_zone_device_unregister causes the
thermal_zone_device structure to be freed before the call to free the
dynamically allocated attribute groups. This leads to a kernel panic.
Furthermore, the 4 calls to free the trip point attribute structures
occur before the call to unregister the device, leading to a kernel
panic when sysfs attempts to access the attributes to remove them.
Here is an example of a kernel panic when the cpu thermal zones are
removed upon cpu offline:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: strlen+0x0/0x20
<snip>
Call Trace:
? kernfs_name_hash+0x17/0x80
kernfs_find_ns+0x3f/0xd0
kernfs_remove_by_name_ns+0x36/0xa0
remove_files.isra.1+0x36/0x70
sysfs_remove_group+0x44/0x90
sysfs_remove_groups+0x2e/0x50
device_remove_attrs+0x5e/0x90
device_del+0x1ea/0x350
device_unregister+0x1a/0x60
thermal_zone_device_unregister+0x1f2/0x210
pkg_thermal_cpu_offline+0x14f/0x1a0 [x86_pkg_temp_thermal]
? kzalloc.constprop.2+0x10/0x10 [x86_pkg_temp_thermal]
cpuhp_invoke_callback+0x8d/0x3f0
cpuhp_down_callbacks+0x42/0x80
cpuhp_thread_fun+0x8b/0xf0
smpboot_thread_fn+0x110/0x160
kthread+0x101/0x140
? sort_range+0x30/0x30
? kthread_park+0x90/0x90
ret_from_fork+0x25/0x30
This patch moves the kfree calls to clean up the dynamic attributes to
the thermal_class's thermal_zone_device release function.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Jacob von Chorus <jacobvonchorus@cwphoto.ca>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
bna & bfa firmware version 3.2.5.1 was submitted to linux-firmware on
Feb 17 19:10:20 2015 -0500 in 0ab54ff1dc ("linux-firmware: Add QLogic BR
Series Adapter Firmware").
bna was updated to use the newer firmware on Feb 19 16:02:32 2015 -0500 in
3f307c3d70 ("bna: Update the Driver and Firmware Version")
bfa was not updated. I presume this was an oversight but it broke support
for bfa+bna cards such as the following
04:00.0 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.1 Fibre Channel [0c04]: Brocade Communications Systems, Inc.
1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.2 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
04:00.3 Ethernet controller [0200]: Brocade Communications Systems,
Inc. 1010/1020/1007/1741 10Gbps CNA [1657:0014] (rev 01)
Currently, if the bfa module is loaded first, bna fails to probe the
respective devices with
[ 215.026787] bna: QLogic BR-series 10G Ethernet driver - version: 3.2.25.1
[ 215.043707] bna 0000:04:00.2: bar0 mapped to ffffc90001fc0000, len 262144
[ 215.060656] bna 0000:04:00.2: initialization failed err=1
[ 215.073893] bna 0000:04:00.3: bar0 mapped to ffffc90002040000, len 262144
[ 215.090644] bna 0000:04:00.3: initialization failed err=1
Whereas if bna is loaded first, bfa fails with
[ 249.592109] QLogic BR-series BFA FC/FCOE SCSI driver - version: 3.2.25.0
[ 249.610738] bfa 0000:04:00.0: Running firmware version is incompatible with the driver version
[ 249.833513] bfa 0000:04:00.0: bfa init failed
[ 249.833919] scsi host6: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.0 driver: 3.2.25.0
[ 249.841446] bfa 0000:04:00.1: Running firmware version is incompatible with the driver version
[ 250.045449] bfa 0000:04:00.1: bfa init failed
[ 250.045962] scsi host7: QLogic BR-series FC/FCOE Adapter, hwpath: 0000:04:00.1 driver: 3.2.25.0
Increase bfa's requested firmware version. Also increase the driver
version. I only tested that all of the devices probe without error.
Reported-by: Tim Ehlers <tehlers@gwdg.de>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Rasesh Mody <rasesh.mody@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a call to mempool_create_slab_pool() in snic_probe() returns NULL,
return -ENOMEM to indicate failure. mempool_creat_slab_pool() only fails
if it cannot allocate memory.
https://bugzilla.kernel.org/show_bug.cgi?id=189061
Reported-by: bianpan2010@ruc.edu.cn
Signed-off-by: Burak Ok <burak-kernel@bur0k.de>
Signed-off-by: Andreas Schaertl <andreas.schaertl@fau.de>
Acked-by: Narsimhulu Musini <nmusini@cisco.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This fix is to avoid calling fnic_fw_reset_handler through
fnic_host_reset when a finc reset is alreay in progress.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull i915 drm fixes from Jani Nikula:
"Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
fixes.
My new year's resolution is to start using signed tags for pulls. If
that feels like a déjà vu, it's ((new year's) resolution), not (new
(year's resolution))"
[ Taking this directly from Jani because Dave Airlie is only partially
connected right now. - Linus ]
* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Prevent timeline updates whilst performing reset
drm/i915: Silence allocation failure during sg_trim()
drm/i915: Don't clflush before release phys object
drm/i915: Fix oops in overlay due to frontbuffer tracking
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
drm/i915: Initialize overlay->last_flip properly
drm/i915: Move the min_pixclk[] handling to the end of readout
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
drm/i915/gvt: fix typo in cfg_space range check
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
drm/i915/gvt/kvmgt: trival: code cleanup
drm/i915/gvt/kvmgt: prevent double-release of vgpu
drm/i915/gvt/kvmgt: check returned slot for gfn
drm/i915/gvt/kvmgt: dereference the pointer within lock
drm/i915/gvt: reset the GGTT entry when vGPU created
drm/i915/gvt: fix an error in opregion handling
If we skip before banning, we have an inconsistent interface between
execbuf still queueing valid request but those requests already queued
being cancelled. If we only cancel the pending requests once we stop
accepting new requests, the user interface is more consistent.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Fixes: 821ed7df6e ("drm/i915: Update reset path to fix incomplete requests")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170105170059.344-1-chris@chris-wilson.co.uk
Now that we have split out a header file for simple macros (that maybe
we can promote into a core header), move a few macros across from
i915_drv.h
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170105164148.26875-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix spelling mistake in print test pass message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Commit 6995f0b (md: takeover should clear unrelated bits) clear
unrelated bits, but it's quite fragile. To avoid error in the future,
define a macro for unsupported mddev flags for each raid type and use it
to clear unsupported mddev flags. This should be less error-prone.
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Trivial fix to spelling mistake "recoverying" to "recovering" in
pr_dbg message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Shaohua Li <shli@fb.com>
r5l_load_log() calls functions that requires a proper conf->log,
for example, r5c_is_writeback(). Therefore, we should set
conf->log before calling r5l_load_log(). If r5l_load_log() fails,
conf->log is set back to NULL.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We only need to update sh->log_start at the end of recovery,
which is r5c_recovery_rewrite_data_only_stripes(), so it is not
necessary to set it before that. In this patch, log_start is
removed from r5c_recovery_alloc_stripe().
After updating all sh->log_start, rewrite_data_only_stripes()
also updates log->next_checkpoints to the last sh->log_start.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The write-through mode has been returned in front of the function,
do not need to do it again.
Signed-off-by: JackieLiu <liuyun01@kylinos.cn>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
[<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
[<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
[<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
[< inline >] create_dir lib/kobject.c:71
[<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
[< inline >] kobject_add_varg lib/kobject.c:366
[<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
[<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
[<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
[<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
[<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
[<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
[<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
[<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263
This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- One fix to the AMD pinctrl ACPI glue.
- Fix requests on the Meson driver.
- Fix bitfield widths on Samsungs Exynos 5433.
-----BEGIN PGP SIGNATURE-----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=t6nv
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Three small pin control fixes for the v4.10 series. Very little to say
about them, just driver fixes.
- one fix to the AMD pinctrl ACPI glue
- fix requests on the Meson driver
- fix bitfield widths on Samsungs Exynos 5433"
* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
pinctrl: meson: fix gpio request disabling other modes
pinctrl/amd: Set the level based on ACPI tables
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 054d4b7b57 ("usb: ohci-at91: Use descriptor-based gpio APIs")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of
the changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I would
not normally have considered for merging after -rc2, but I decided to
take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and we
have to put empty /chosen nodes back to be able to pass kernel command
lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200,
as it had been for no good reason for a long time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J2uq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYbgWzAAoJELDendYovxMvzqQH/iO+SKCrT39q6fCP+fyov7Hi
J67XrHVT/AAPUXizWzKdtBE5EdI+WZXBkdsCEh3+3XPCeCRL/t9dRYEytle0Ioy9
hXC5otiJQ1hhm2N5dQKT5c0IMVh9mAjbeIqcG2dV1lSVaw0CYcJS4xh9eALxj7UY
eXGpNMdNyeiEG2p5OgnDE5GqHavxPh+6ChNxmr8341T8E+C9U1BNtJeUiIQshKmC
YAlt7YWoPzEJeLAYEiwrROYNyrLNd17IlYOeKXSwZUdkVtZahW+/jO+YYmhbx1C/
Yvt93r7ewUFKslRgpZQjjl8y9eynKg+j2BWx8WjAwpdHfCa1DFEOxiAOraLp7Cc=
=ro0H
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
Update the Hyper-V MAINTAINERS to include myself.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring
The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aa ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than keep a list of all possible compression types in the
Makefile, set the target explicitly from Kconfig.
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using initramfs compression, the data file compression suffix
gets quotes pulled in from Kconfig, e.g., initramfs_data.cpio".gz"
which make does not match a target and causes rebuild.
Fix this by filtering out quotes from the Kconfig string.
Fixes: 35e669e1a2 ("initramfs: select builtin initram compression algorithm on KConfig instead of Makefile")
Reviewed-by: Francisco Blas Izquierdo Riera (klondike) <klondike@klondike.es>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Forbid compiling xway NAND controller driver as a module
- Fix tango NAND DT binding and make sure the controller is in a clean
state at probe time
- Add dependency on HAS_IOMEM to the oxnas NAND driver
- Fix irq number validity check in the lpc32xx driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Dg9f
-----END PGP SIGNATURE-----
Merge tag 'nand/fixes-for-4.10-rc3' of github.com:linux-nand/linux
From Boris Brezillon:
"""
Fixes for 4.10-rc3
- Forbid compiling xway NAND controller driver as a module
- Fix tango NAND DT binding and make sure the controller is in a clean
state at probe time
- Add dependency on HAS_IOMEM to the oxnas NAND driver
- Fix irq number validity check in the lpc32xx driver
"""
There is no mmc sd card detect on am335x-ice board. But the spi0_cs1
pin being configured as mmcsd_cd. Removing it fixes the below warning
during boot:
pinctrl-single 44e10800.pinmux: pin 44e10960.0 already
requested by 48030000.spi; cannot claim for 48060000.mmc
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: tidied up commit message]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 485fa1261f ("ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth")
set the wrong baud rate for the UART. The Baud rate was 300,000 and it should
be 3,000,000 for WL1283.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
