We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this
function is called indirectly from rt2800_enable_radio(). If we
do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Firmware doesn't update beacon/Probe Response vendor IEs correctly when
bss is down, so we move brcmf_config_ap_mgmt_ie after BSS up. And host
driver should clear IEs when AP stopped so that the IEs in host side will
be synced with in firmware side.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB"
will not cover the case when it is configured as module. This will
omit the entire if-block which does cleanup of URBs and cancellation
of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current limit is too low for latest cards with 8+ tuners on a single slot.
IMHO, the most appropriate minimum default is 16.
Signed-off-by: Буди Романто, AreMa Inc <knightrider@are.ma>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In randconfig builds that select VIDEO_EM28XX_V4L2 and
MEDIA_SUBDRV_AUTOSELECT, but not MEDIA_CAMERA_SUPPORT, we get
a Kconfig warning:
warning: (VIDEO_EM28XX_V4L2) selects VIDEO_MT9V011 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This avoids the warning by making that 'select' conditional on
MEDIA_CAMERA_SUPPORT. Alternatively we could mark EM28XX as
'depends on MEDIA_CAMERA_SUPPORT', but it does not seem to
have any real dependency on that itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If MEDIA_SUBDRV_AUTOSELECT and VIDEO_GO7007 are both set, we
automatically select VIDEO_OV7640, but that depends on MEDIA_CAMERA_SUPPORT,
so we get a Kconfig warning if that is disabled:
warning: (VIDEO_GO7007) selects VIDEO_OV7640 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This adds another dependency so we don't accidentally select
it when it is unavailable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use UIDs as domain numbers if the UID checking rules apply (in this
case the FW guarantees uniqueness of these values).
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enable the contiguous memory allocator but set the default size to
zero. If somebody wants to use the cma allocator the "cma=" kernel
parameter has to be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In order to make the cma infrastructure usable we need to add a small
architecture backend which calls dma_contiguous_reserve.
Otherwise we would end up with the cma allocator enabled, but no pool
where memory can be allocated from.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the psw_bits macro and simplify the code. The generated code is
also better since it doesn't contain any conditional branches anymore.
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We have the s390 specific THREAD_ORDER define and the THREAD_SIZE_ORDER
define which is also used in common code. Both have exactly the same
semantics. Therefore get rid of THREAD_ORDER and always use
THREAD_SIZE_ORDER instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For an unknown (historic) reason the s390 specific implementation of
set_fs returns whatever the __ctl_load would return. The set_fs macro
however is supposed to return void.
Change the macro to do that.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The systime function uses struct timespec, which we want to stop
using in the kernel because it overflows in 2038. Fortunately,
this use in dibx000_common is in a function that is never called,
so we can just remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In order to avoid a section mismatch drop the call to
of_flat_dt_get_machine_name() when printing the error message.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In order to avoid a section mismatch drop the call to
of_flat_dt_get_machine_name() when printing the error message.
While we're at it: fix a typo.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New power management wmi commands provide the ability to change
the device power save profile (enable / disable power save).
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.
The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The stv090x driver uses the lookup table for signal strength already,
with this patch we use the lookup tables for carrier/noise ratio as well.
This has the advantage, that values for DVB-S and DVB-S2 are now
corresponding, while before they were way off. The values are now
proportional to real carrier/noise ratio, while before they were
corresponding to register values. So now applications are able to give
the user real carrier/noise ratio.
Because the output has to be within 0x0000...0xFFFF the three negative
values for DVB-S2 are omitted. This is no significant loss, because
reception is lost at 7.5 dB already (TT S2-1600, Cine S2), so the
negative values are not really important, and also for DVB-S they don´t
exist.
Signed-off-by: Joerg Riechardt <j.riechardt@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the S25FL127S nor flash part, each writing to the configuration
register takes hundreds of ms. During that time, no more accesses to
the flash should be done (even reads).
This commit adds a wait loop after the register writing until the flash
finishes its work.
This issue could make rootfs mounting fail when the latter was done too
much closely to this quad enable bit setting step. And in this case, a
driver as UBIFS may try to recover the filesystem and may broke it
completely.
Signed-off-by: Joël Esponde <joel.esponde@honeywell.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Since commit 6f3b911d5f ("can: bcm: add support for CAN FD frames") the
CAN broadcast manager supports CAN and CAN FD data frames.
As these data frames are embedded in struct can[fd]_frames which have a
different length the access to the provided array of CAN frames became
dependend of op->cfsiz. By using a struct canfd_frame pointer for the array of
CAN frames the new offset calculation based on op->cfsiz was accidently applied
to CAN FD frame element lengths.
This fix makes the pointer to the arrays of the different CAN frame types a
void pointer so that the offset calculation in bytes accesses the correct CAN
frame elements.
Reference: http://marc.info/?l=linux-netdev&m=147980658909653
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and SOC")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.
This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.
Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current set_tsf is implemented in terms of TSF_INCREMENT
only. Instead support new WMI command TSF_DECREMENT and
export these through offset_tsf. Advantage is we get
more accurate TSF adjustments, and don't calculate wrong
offset in case absolute TSF was calculated from rx_mactime
(actual TSF).
The new WMI command is available in firmware
10.4-3.2.1-00033 for QCA4019 chips. Old drivers on new
firmware or vice versa shouldn't be a problem since
get/set tsf logic was already broken.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If callchains were recorded they are appended to the line with a default stack depth of 5:
1.874569 [0011] gcc[31949] 0.014 0.000 1.148 wait_for_completion_killable <- do_fork <- sys_vfork <- stub_vfork <- __vfork
1.874591 [0010] gcc[31951] 0.000 0.000 0.024 __cond_resched <- _cond_resched <- wait_for_completion <- stop_one_cpu <- sched_exec
1.874603 [0010] migration/10[59] 3.350 0.004 0.011 smpboot_thread_fn <- kthread <- ret_from_fork
1.874604 [0011] <idle> 1.148 0.000 0.035 cpu_startup_entry <- start_secondary
1.874723 [0005] <idle> 0.016 0.000 1.383 cpu_startup_entry <- start_secondary
1.874746 [0005] gcc[31949] 0.153 0.078 0.022 do_wait sys_wait4 <- system_call_fastpath <- __GI___waitpid
--no-call-graph can be used to not show the callchains. --max-stack is used
to control the number of frames shown (default of 5). -x/--excl options can
be used to collapse redundant callchains to get more relevant data on screen.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-7-namhyung@kernel.org
[ Add documentation based on above commit message ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The -s/--summary option is to show process runtime statistics. And the
-S/--with-summary option is to show the stats with the normal output.
$ perf sched timehist -s
Runtime summary
comm parent sched-in run-time min-run avg-run max-run stddev
(count) (msec) (msec) (msec) (msec) %
---------------------------------------------------------------------------------------------------------
ksoftirqd/0[3] 2 2 0.011 0.004 0.005 0.006 14.87
rcu_preempt[7] 2 11 0.071 0.002 0.006 0.017 20.23
watchdog/0[11] 2 1 0.002 0.002 0.002 0.002 0.00
watchdog/1[12] 2 1 0.004 0.004 0.004 0.004 0.00
...
Terminated tasks:
sleep[7220] 7219 3 0.770 0.087 0.256 0.576 62.28
Idle stats:
CPU 0 idle for 2352.006 msec
CPU 1 idle for 2764.497 msec
CPU 2 idle for 2998.229 msec
CPU 3 idle for 2967.800 msec
Total number of unique tasks: 52
Total number of context switches: 2532
Total run time (msec): 218.036
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-5-namhyung@kernel.org
[ Add documentation from last commit, so that docs comes with the cset that introduces the feature ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf sched timehist' provides an analysis of scheduling events.
Example usage:
perf sched record -- sleep 1
perf sched timehist
By default it shows the individual schedule events, including the wait
time (time between sched-out and next sched-in events for the task), the
task scheduling delay (time between wakeup and actually running) and run
time for the task:
time cpu task name wait time sch delay run time
[tid/pid] (msec) (msec) (msec)
-------------- ------ -------------------- --------- --------- ---------
79371.874569 [0011] gcc[31949] 0.014 0.000 1.148
79371.874591 [0010] gcc[31951] 0.000 0.000 0.024
79371.874603 [0010] migration/10[59] 3.350 0.004 0.011
79371.874604 [0011] <idle> 1.148 0.000 0.035
79371.874723 [0005] <idle> 0.016 0.000 1.383
79371.874746 [0005] gcc[31949] 0.153 0.078 0.022
...
Times are in msec.usec.
Committer note:
Add above explanation as the 'perf sched timehist' entry for 'man
perf-sched'.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The __symbol__fprintf_symname_offs() always shows symbol offsets. So
there's no difference between 'perf script -F ip,sym' and 'perf script
-F ip,sym,symoff'. I don't think it's a desired behavior..
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20161116060634.28477-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding support for cascading options added by Namhyung in:
commit 369a247897 ("tools lib subcmd: Support cascading options")
This way the report and record command share options with with c2c
command and can save some option duplicates. For now it's the 'v'
option.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-7-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently we display the cacheline list sorted on remote HITMs by
default.
The problem is that they might not be always counted and 'perf c2c
report' displays an empty output. Thus it's more convenient to display
and sort the cacheline list based on the total of HITMs and have the
best change to see data in the default report run.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-6-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Count total number of HITMs in a special field. This will ease up
addition of total HITM sorting into c2c report in the following patch.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-5-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding -f/--force option to go through ownership validation:
$ sudo perf c2c report
File perf.data not owned by current user or root (use -f to override)
$
$ sudo perf c2c report -f
< c2c report output >
$
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Because of the early browser switch we won't get possible error
messages, as it will clear the screen right after showing the message,
e.g.:
Before:
$ sudo perf c2c report -d lcl
$
After:
$ sudo perf c2c report -d lcl
File perf.data not owned by current user or root (use -f to override)
$
$ ls -la perf.data
-rw-------. 1 acme acme 26648 Nov 22 15:11 perf.data
$
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is useful for debug to see file descriptors for each event.
Before:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12146 cpu -1 group_fd -1 flags 0x8
...
sys_perf_event_open: pid 12146 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Now:
$ perf stat -vvv -e cycles,cache-misses ls
...
sys_perf_event_open: pid 12858 cpu -1 group_fd -1 flags 0x8 = 3
...
sys_perf_event_open: pid 12858 cpu -1 group_fd 3 flags 0x8
sys_perf_event_open failed, error -13
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Joe Mario <jmario@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1479764011-10732-2-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
