As pointed out by smatch, checking the BAID for just >= INVALID
is a bad idea since only 32 (IWL_MAX_BAID) actually exist. Check
the range for that and print invalid ones in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Inside the reorder timer expire function, there's no point in
disabling BHs since it is in BH context. Remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware ever decides to send any new/more notifications
to the RSS queues, the driver would currently try to interpret
those as REPLY_RX_MPDU_CMD and, if the notification was small,
access invalid memory.
Prevent that by checking for REPLY_RX_MPDU_CMD explicitly which
allows ignoring unexpected notifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use setup_timer function instead of initializing timer with the function
and data fields
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA is removed in DQA mode, if no traffic went through
its reserved queue, the txq continues to be marked as
reserved and no STA can use it.
Make sure that in such a case the reserved queue is marked
as free when the STA is removed.
Fixes: commit 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_rx_tx_cmd_single(), when checking if a given TID is
aggregated, the driver doesn't check whether or not the queue
itself can be aggregated. For example, a management queue might
be marked as aggregated if TID 0 is aggregated on a (different)
data queue.
Make sure that mgmt frames are sent with TID IWL_TID_NON_QOS,
and in this way make sure no mixups of this sort happen.
Fixes: commit 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support new format. TX response will not be sent anymore,
so all needed data is in the BA response.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we have 15 fifos, so in the shared memory
config the number of tx fifos in the array was changed
accordingly.
As it is in the middle of the struct, the parsing code needs
to be duplicated.
To minimize the duplication, do not save variables we never
actually use.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Firmware may lock those registers for access. This results
in 9000 devices with a bus stall and an endless loop of 0x5a5a5a.
Don't dump those registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, a delBA might free the queue although it
shouldn't. Fix that.
Fixes: cf941e174ee2 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the SCD_QUEUE_CFG command was introduced the driver
calls iwl_trans_txq_enable_cfg() with a NULL for scd_cfg
parameter.
This makes the transport avoid writing to the SCD pointers,
since it can cause races with firmware, which is also accessing
the registers.
The transport only updates the write pointer in that case.
Fix a wrong call to iwl_trans_txq_enable() which caused a
scd_cfg parameter to be sent to transport, resulting with an
access to SCD registers.
Fixes: 58f2cc57dc ("iwlwifi: mvm: support dqa-mode scd queue redirection")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Off-channel action frames (such as ANQP frames) must be sent either on
the AUX queue or on the offchannel queue, otherwise the firmware will
cause a SYSASSERT.
In the current implementation, the queue to be used is correctly set in
the original skb, but this is done after it is copied. Thus the copy
remains with the original, incorrect queue.
Fix this by setting the queue in the original skb before copying it.
Fixes: commit 5c08b0f502 ("iwlwifi: mvm: don't override the rate with the AMSDU len")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Every active TXQ is assigned to a TID given through the
SCD_CONFIG_CMD, and acts as an identifier in the FW. However,
there may be cases this ownership needs to be changed.
For example, in the following scenario:
1. TID x is owner of a queue
2. Due to a shortage of queues, TID y and z share with x
3. TID x becomes inactive and needs to be removed from the
shared queue.
In this scenario, if another queue is freed and traffic on x
continues, we can't allocate it a new queue as long as it is
the owner of the first queue.
Support moving ownership of a TXQ to a different TID (same
STA) without stopping the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to the addition of another option in the SCD_CONFIG_CMD's
%enable field, change the assignment of this field to use
defines rather than hard-code the value itself.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When working in DQA mode, if a queue is shared and a HW restart
occurs, there might be a possible race condition between
stations on the queues, and an existing queue might be left
with no queues.
To solve this, make sure in DQA mode to re-assign the same
queues as before the HW restart.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending the SCD_QUEUE_CONFIG command, the queue is
associated to a specific TID. If later there is a need to
use this TID on a different queue instead, it first needs to
be unassociated from the first queue.
Keep track for every queue what TID is associated with it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a shared queue becomes unshared, aggregations should be
re-enabled if they've existed before. Make sure that they do
this, if required.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices there is a support of 64 bit DMA addressing.
The paging command was changed accordingly - support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for installing and removing GMAC key
for newer FW versions that support GCM and MFP.
GMAC provides authentication and integrity for multicast management
frames.
Firmware API was changed, update the driver accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 9000 hardware will de-aggregate AMSDUs. In the process
it will copy the mac header "as is" to the new MPDUs.
This means driver should allow the same PN for MPDUs originated
from the same AMSDU.
Do that by incrementing the PN only for the last MPDU in the
sequence.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwlmvm driver supports channel width change in AP mode. Add the
proper flag.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
fw-dbg code return ret but that variable was either 0
or not initialised. Return 0 always.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 6a95126763 ("iwlwifi: mvm: send dbg config hcmds to fw if set in tlv")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the user really wanted a dump on P2P Client, he
coudln't get it because we checked vif->type but didn't
take vif->p2p into account. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXhmR1AAoJEG4XJFUm622bn+gH/Ar5l/oU76nmXKh0xNiV6bUE
2FuRV9X7ynAOLbFJfqZvN8eL1kTyztXOpxVOt9xLZvNcrJP2mdOH+YdUpSPk/XRw
mpFC7RCln/Y1bbX02la7V8iRJlKK1/VmdMABJXsalDcxSPMhhBQtr4/ZC7NcgmeJ
zKCZDGr/x4qpmAkYGsf3msJsBotHtt9xuHp4fFswp9Gpm+VeqtdqGEeMxowoILRK
QBj6nZIuLI4PMnJhfCJn94t9D/AVUIVJTeuWNDS5Up4gZVFo9SlpnkR520P0IY4Q
1238g5sAdKqONsPO0lyUacUlY2cTafDr4kD6UKnjf659KDd49MDJArpfbvMeweY=
=PTV+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.8
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PpSg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work on DQA continued
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the v4 version of the TX power command. Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.
This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This led to a DMA splat.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value for Channel 14 was wrong. Fix it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3a6 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure. If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit f4a3ee493e ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZrY
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-01' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* More work on the RX path for the 9000 device series
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.
Fixes: 585a6fccf5 ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up without leading spaces here, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
My cleanup in "iwlwifi: prepare for higher API/CAPA bits" accidentally
inverted a few tests - fix them.
Fixes: 859d914c8f ("iwlwifi: prepare for higher API/CAPA bits")
Reported-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW expect the driver to set the encryption algorithm type when
installing the IGTK key in the HW.
Currently when installing CMAC IGTK key we don't set the algorithm type
and as a result the FW fails to calculate the MIC of multicast management
frames.
Fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We try to access sta before we check for IS_ERR_OR_NULL(), so we may
end up accessing a NULL pointer. To prevent that, move the conversion
from sta to mvm_sta below the check.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 16 seconds timeout we were using turned out to be too short.
Recalculations by system show that the total time in both bands should
be < 18.5 seconds, even in the slowest cases (e.g. DCM P2P with
DTIM=2). Rounding it up to 20 seconds for a bit more safety.
Fixes: 728e825f81 ("iwlwifi: mvm: add a scan timeout for regular scans")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with removing
debugfs files should be fixed thanks to the great work of Nicolai Stange. We
also have some isa updates in here (the x86 maintainers told me to take it
through this tree), a new warning when we run out of dynamic char major
numbers, and a few other assorted changes, details in the shortlog.
All have been in linux-next for some time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0mwACgkQMUfUDdst+ynjXACgjNxR5nMUiM8ZuuD0i4Xj7VXd
hnIAoM08+XDCv41noGdAcKv+2WZVZWMC
=i+0H
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with
removing debugfs files should be fixed thanks to the great work of
Nicolai Stange. We also have some isa updates in here (the x86
maintainers told me to take it through this tree), a new warning when
we run out of dynamic char major numbers, and a few other assorted
changes, details in the shortlog.
All have been in linux-next for some time with no reported issues"
* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
gpio: ws16c48: Utilize the ISA bus driver
gpio: 104-idio-16: Utilize the ISA bus driver
gpio: 104-idi-48: Utilize the ISA bus driver
gpio: 104-dio-48e: Utilize the ISA bus driver
watchdog: ebc-c384_wdt: Utilize the ISA bus driver
iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
iio: stx104: Add X86 dependency to STX104 Kconfig option
Documentation: Add ISA bus driver documentation
isa: Implement the max_num_isa_dev macro
isa: Implement the module_isa_driver macro
pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
isa: Decouple X86_32 dependency from the ISA Kconfig option
driver-core: use 'dev' argument in dev_dbg_ratelimited stub
base: dd: don't remove driver_data in -EPROBE_DEFER case
kernfs: Move faulting copy_user operations outside of the mutex
devcoredump: add scatterlist support
debugfs: unproxify files created through debugfs_create_u32_array()
debugfs: unproxify files created through debugfs_create_blob()
debugfs: unproxify files created through debugfs_create_bool()
...
In non-shared queues, DQA requires re-configuring existing
queues to become aggregated rather than allocating a new
one. It also requires "un-aggregating" an existing queue
when aggregations are turned off.
Support this requirement for non-shared queues.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The commit below added code to dump the content of FIFOs
that are present only on dual CPU products (8000 and up).
This broke 7265D whose firmware does advertise
IWL_UCODE_TLV_CAPA_EXTEND_SHARED_MEM_CFG but doesn't have 2
CPUs. The current code does check the length of the FIFO
before dumping them (and the nonexistent FIFO has a 0
length), but we still accessed a register to set the FIFO
number and that made the DMA unhappy.
The impact was a much longer recovery upon firmware assert.
Fixes: 5b08641429 ("iwlwifi: mvm: support dumping UMAC internal txfifos")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_phy_db_set_section() is get called only from atomic
context, the alloc_ctx parameter is not needed. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up till now, the reorder buffer uses standard spec based comparison
when comparing the buffer status to NSSN. This indeed works for the
regular case, since we shouldn't cross the 2048 boundary without
getting a frame release notification.
However, this is problematic due to packet filtering that may be
performed by the FW while we are in d0i3. Theoretically we may
filter over 2048 packets, and then the check of the NSSN will get
incorrect.
Change the comparison to always trust nssn unless it is 64 or less
frames behind the head - which might happen due to a timeout.
This new comparison is to be used only when comparing reorder buffer
head with nssn, and not when comparing the packet SN to nssn or
reorder buffer head.
Put this in a separate commit as the logic is a bit tricky and
stands for its own commit message.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code allows mvm reference to become negative and
only warns in case mvm reference is released while reference
counting is 0.
However, we better prevent this from happening at all since
iwl_mvm_unref() may race against iwl_mvm_unref_all_except()
which is called on restart.
As a result we might get the same reference unreferenced twice
ending with a negative value:
An example for an easily reproduced log:
[ 2689.909166] iwl_mvm_ref Take mvm reference - type 8
[ 2690.732716] iwl_mvm_unref_all_except Cleanup: remove mvm ref type 8 (1)
[ 2690.849708] iwl_mvm_unref Leave mvm reference - type 8
[ 2690.849721] WARNING: ... iwl_mvm_unref+0xb0/0xc0 [iwlmvm]()
If there will be yet another another restart iwl_mvm_unref_all_except
will run from 0 up to ref count, and since it is unsigned, we will throw
the transport ref count completely out of balance:
iwl_mvm_unref_all_except[I] -- Cleanup: remove mvm ref type 8 (255)
iwl_trans_slv_unref[I] -- rpm counter: 0
iwl_trans_slv_unref[I] -- rpm counter: -1
iwl_trans_slv_unref[I] -- rpm counter: -2
...
iwl_trans_slv_unref[I] -- rpm counter: -253
iwl_trans_slv_unref[I] -- rpm counter: -254
As there is no valid scenario where we can get to a negative
reference count - prevent it from happening.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add UREG, RXFC, RFH, WMAL and RL2P registers to the prph dump
upon error. These regesiters could help to debug MSI-X and other
issues.
These register should be dumped only when multi-queue rx is supported
so separate the prph ranges static array to two different arrays,
and enable dumping different prph ranges according to run-time
decision.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a data packet is received, we need to make sure that we stay
awake until it can be processed and wait a while before trying to
enter runtime_suspend os system_suspend again. To do so, add a new
reference type for RX data and take the reference when sending the
packet to mac80211. We only do this for data packets, all the other
RX packets sent by the firmware (e.g. notifications) are not a reason
to prevent suspend.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a host command was queued while in runtime suspend, it would go out
before the D0I3_END_CMD was sent. Sometimes it works, but sometimes
it fails, and it is obviously the wrong thing to do.
To fix this, have the opmode take a reference before sending a SYNC
command and make the pcie trans wait for the runtime state to become
active before actually queueing the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debugfs knob to configure the maximal length
of the A-MSDU. If this value is not 0 (which is the
default), allow Tx A-MSDU even if the rate control
disallows it.
While at it, add "unlikely" to the if that limits the
length of the A-MSDU based on the debugfs hook.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a constant to allow disabling checksum. This will enable easier
debugging in early phases.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To indicate to the FW that a queue has been removed, an
existing flag in the ADD_STA HCMD (that hasn't been in use)
has been changed to indicate that a queue is being removed
from a STA.
Update this in the driver code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will send frame release notification in order
to release "stuck" frames on a queue where no more frames
arrive on.
Upon receiving the message the driver shall indicate the frames
up to the NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a timer in order to release expired frames from the
reorder buffer.
This is needed since some APs do not retransmit frames
to fill in the reorder holes and in TCP it results with
a complete stall of traffic.
This has a few side effects on the general design:
The nssn may not reflect the the head of the reorder buffer.
This situation is valid, and packets with SN lower than the
reorder buffer head will be dropped.
Another side effect is that since the reorder timer might expire
we need to lock the reorder buffer.
This however is fine since the locking is only inside a
single reorder buffer between RX path and reorder timeout and
there is no outside contention.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.
The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.
The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the firmware API name to the struct iwl_wowlan_gtk_status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
