Pull kbuild updates from Michal Marek:
- Make <modname>-m in makefiles work like <modname>-y and fix the
fallout
- Minor genksyms fix
- Fix race with make -j install modules_install
- Move -Wsign-compare from make W=1 to W=2
- Other minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Demote 'sign-compare' warning to W=2
Makefile: revert "Makefile: Document ability to make file.lst and file.S" partially
kbuild: Do not run modules_install and install in paralel
genksyms: Handle string literals with spaces in reference files
fixdep: constify strrcmp arguments
ath10k: Fix build with CONFIG_THERMAL=m
Revert "drm: Hack around CONFIG_AGP=m build failures"
kbuild: Allow to specify composite modules with modname-m
staging/ad7606: Actually build the interface modules
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use SMPS disabled as default because FW does not indicate
any support of SMPS.
This change will help STAs out that don’t support SMPS from
sticking on 1SS, since they don’t have method to change it
back to multiple chains.
This change also should not affect power consumption of STAs
supporting SMPS, because they are capable to switch the mode
to dynamic or static either at the end of frame sequence or
by using SMPS action frame.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 1aaf8efba0 ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d409c ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Mesh Point requires peer security key install when running
in secured mode since it's a type of peer links, otherwise peer
link will be removed due to key install failure.
MFP feature set is required to run Mesh in secured mode and
QCA988X firmware, 10.2.4.70.14-2 and above, is the only one
supporting secured Mesh at this moment.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWZcQtAAoJEG4XJFUm622bgcMH/1VRwtzAKpYVwAyAN0MtVLxe
uANi0Pw1PmEAeEI3TxEBckEH0JYfpg+aAwX7S8scnQSvLP3FYeC5IcHG551vlh0s
FlkGexcXqGrDqjt8mz8hxqqAmMH9YEVlzj2HJf6YFjNS4K84CEgpaSjaSG8S7Wc8
hTSA5K+XxrnEeX41W7FYmeBFLejisg0gVTkS3ZCe4qYz4Gh1oamoA0pOdU+AYOMy
0XBkCT8fqTVXWLHh9/+J7IZOYrjBl4rVaHofeygEAfSRNNfmmjZXX1R+FCQoJEZC
IOEQ31T64G4A37t2N2RGOhiG+2vckdbPg2JsqJosI1L2OZSBbeGZsVW48w+5cgc=
=GQDA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Coherent memory is more expensive to allocate (and constrained on some
architectures where it has to be pre-allocated). It is also completely
unnecessary, since the host has no reason to even access these allocated
memory spaces
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default values of max_num_amsdu / max_num_amdpu is assigned a
default value as part of 'ath10k_core_init_firmware_features'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes:
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
When debugging firmware problems it's useful to check checksums of each
component. Add a debugfs interface to retrieve crc32 checksums:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/fw_checksums
firmware-N.bin cc3fb466
athwlan c0089f21
otp f3efeb4f
codeswap 00000000
board-N.bin bebc7c08
board bebc7c08
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier we printed all the info messages after a successful device
initialisation and firmware boot, but that's problematic if something goes
wrong and there's no easy way to know what firmware version was used and so on.
Split the info messages into smaller pieces and print them as soon as we have
the info available.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 has capability to support
Mesh Control Field Present bit in QoS field in native Wi-Fi mode.
Hence apply Mesh subtype according to the WMI service map.
Firmware will allows unicast, broadcast, multicast, and WDS frame
(FromDS = 1 and ToDS = 1) to be received via the interface, once Mesh
subtype is used.
The firmware and this patch together make native Wi-Fi mode comply to
IEEE802.11s Mesh frame in open mode, but the firmware doesn't yet
support secured Mesh mode.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X firmware starting from 10.2.4.70.12-2 supports new
vdev subtypes for proxy STA and Mesh, hence add them to be used
as needed.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update WMI 10.x service map to sync with firmware 10.2.4.70.12-2
released on 11/11/2015 which is the latest QCA988X firmware as of
11/18/2015.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix write permission for few of the debugfs entries
which support write file operations as well.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allocations from the DMA zone were originally added for legacy ISA
stuff, or PCI devices that have specific limitations in their DMA
addressing capabilities. It has no place in ath10k, which can do
full 32-bit DMA.
Fixes memory allocation errors on some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable AP + STA interface combination support for 10.x and
this enables Repeater mode testing (with WDS Repeater combinations
as well). Fix indentation as well.
Based on the suggestions from Michal and Yanbo Li,
thanks to them
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The error message order of board data fetch is board info,
directory, and then file name, hence place print arguments
in the order.
Fixes: 0a51b343ab ("ath10k: add board 2 API support")
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After commit cf4f21938e ("kbuild: Allow to specify composite modules
with modname-m"), thermal.c gets included in the driver and the build
fails with
drivers/net/wireless/ath/ath10k/thermal.c:119:6: error: redefinition of ‘ath10k_thermal_event_temperature’
drivers/net/wireless/ath/ath10k/thermal.h:54:20: note: previous definition of ‘ath10k_thermal_event_temperature’ was here
drivers/net/wireless/ath/ath10k/thermal.c:136:6: error: redefinition of ‘ath10k_thermal_set_throttling’
drivers/net/wireless/ath/ath10k/thermal.h:59:20: note: previous definition of ‘ath10k_thermal_set_throttling’ was here
drivers/net/wireless/ath/ath10k/thermal.c:162:5: error: redefinition of ‘ath10k_thermal_register’
drivers/net/wireless/ath/ath10k/thermal.h:45:19: note: previous definition of ‘ath10k_thermal_register’ was here
drivers/net/wireless/ath/ath10k/thermal.c:216:6: error: redefinition of ‘ath10k_thermal_unregister’
drivers/net/wireless/ath/ath10k/thermal.h:50:20: note: previous definition of ‘ath10k_thermal_unregister’ was here
Change the #ifdef to reflect the new kbuild behavior.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Txbuf is no longer a DMA pool and can be easily
tracked with a mere msdu_id. This saves 10 bytes
on 64bit systems and 6 bytes on 32bit systems of
precious sk_buff control buffer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prepares the driver for future ieee80211_txq
and wake_tx_queue() support.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames are not guaranteed to be 802.11 frames in
ath10k_htt_tx() and the tx completion handler.
In some cases, like TDLS, they can be Ethernet.
Hence checking, e.g. frame_control could yield
bogus results and behavior.
Fortunately this wasn't a real problem so far
because there's no FW/HW combination to encounter
this problem.
However it is good to fix this in advance.
Fixes: 75d85fd999 ("ath10k: introduce basic tdls functionality")
Fixes: eebc67fef3 ("ath10k: fix pmf for wmi-tlv on qca6174")
Fixes: 7b7da0a021 ("ath10k: drop probe responses when too many are queued")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to have all the flags as separate
bools.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to keep it in the struct because
it can be passed as function argument down the tx
path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All functions should have ath10k_{filename}_
prefixes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was wasteful to have two flags describing
the same thing.
While at it fix code style of
ath10k_tx_h_use_hwcrypto().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA99X0 4 addresses RX packets pad 2 bytes at the beginning of
MSDU instead the end of ieee80211 header to keep alignment. The currently RX
data path can't parse the header correctly in this case. This patch fixes it
for QCA99X0.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: checkpatch fixes and naming changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX rate idx is not correct for 11G mode OFDM packet.
Because the bitrate table start with CCK index instead of OFDM.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
moved send completion polling under HTT Rx (CE 5) service routine. For
QCA6174 based devices copy engine 1 (CE 1) is used for HTT Rx instead
of CE 5. So send completion never be called. This is causing "failed to
transmit packet, dropping: -105" errors. Fix this by processing send
completion from CE 1 service routine instead of CE 5.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Tested-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Of a word in struct htt_data_tx_desc htt version >= 3.4 firmware uses
LSB 16-bit for frequency configuration which is used for offchannel tx
and MSB 16-bit is for peerid. But other firmwares using version 2.X
(10.1, 10.2.2, 10.2.4 and 10.4) are using 32-bit for peerid in htt tx
desc. So far no issue is found with the existing code setting peerid and
freq for HTT version 2.X, this could be mainly because of 0 as frequecy
(home channel) is being always passed with those firmwares. There may be
issues when non-zero freq is passed with firmware using < 3.4 htt version.
To be safe use target_version_major and target_version_minor along with
htt-op-version before configuring peer id and freq in htt tx desc. This
patch extends ath10k_mac_tx_frm_has_freq() to check for htt_op_version_tlv
and uses the helper while setting peerid in htt_tx_desc.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename ath10k_mac_need_offchan_tx_work() to ath10k_mac_tx_frm_has_freq()
to make it more meaningful. This helper will be used in the future
change. No functionality change.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is an extra 4-byte member when compared to WMI 10.2 added to
assoc complete command in WMI 10.4. This new member is used for 160Mhz
related configuration. This WMI command mismatch between host and
firmware does not cause any real issues because this new member is not
used in 10.4 firmwares so far (10.4.1.00030-1). This difference in WMI
command interface brings in a new wmi_ops for 10.4 gen_peer_assoc().
No noticeable functionality differences with this change can be seen
with the current 10.4 firmwares, but the WMI interface has to be
fixed to work with future 10.4 firmwares which may be using this new
member.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
introduced to use the unused CE5 for target to host message. For the device
like QCA6174, CE5 already assigned for other feature. So for QCA6174, override
the CE5 configuration and use the CE1 instead.
This patch is based on Rajkumar's earlier patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add new BMI target version and chip id revision. Register it
on supported chips list.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A follow up patch introducing a QCA9377 hw1.0 support will need
this device identification helper for an explicit distinction of
HWs, as apparently both QCA6174 hw3.0 and QCA9377 share the same BMI
target version (0x0502000x). For the QCA9377 hw1.1 previously
added we were just lucky we did not overlap with the same chip_id_rev.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The uart_pin was incorrectly configured for QCA9377
and the recently added hw_params were omitted.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When introducing the original QCA9377 support, the chip target
version was wrongly picked. The chip advertising itself with
bmi target value equal to 0x05020001 is in fact a 1.1 revision.
I realized this once I got a real 1.1 hw to play with.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of spatial streams that are derived from chain mask
for 4x4 devices is using wrong bitmask and conditional check.
This is affecting downlink throughput for QCA99x0 devices. Earlier
cfg_tx_chainmask is not filled by default until user configured it
and so get_nss_from_chainmask never be called. This issue is exposed
by recent commit 166de3f189 ("ath10k: remove supported chain mask").
By default maximum supported chain mask is filled in cfg_tx_chainmask.
Cc: stable@vger.kernel.org
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
As not all QCA98XX radios are not connected to Bluetooth modules, enabling the
BT coex feature in firmware will have side effects if the radio's GPIO are
connected with other (non-BT) HW modules. Add debugfs file to control the
firmware BT coex logic and set the feature as disable by default to avoid that
btcoex is accidentally enabled.
To enable this feature, execute:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
To disable:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/btcoex
The firmware support this feature since 10.2.4.54 on 2G-only board, dual band
or 5G boards don't support this. The feature's name is WMI_SERVICE_COEX_GPIO
and the btcoex file is not created if firmware doesn't support it.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: use btcoex filename and other smaller fixes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds pktlog support for 10.4 fw versions.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functionality change, just sync to the latest
pdev params that 10.4 firmware defines.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No real functionality change, add WMI command/event
defines to be in sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, adds new wmi service bits for
10.4 firmware to be sync with 10.4 firmware.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables thermal throttling support for 10.4 firmware.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set peer's management frame protection flag in peer assoc command,
this setting will enable/disable encrytion of management frames in fw.
Setting of this flag is based on whether MFP is enabled/disabled at STA
and a firmware feature flag ATH10K_FW_FEATURE_MFP_SUPPORT. This is because
only firmwares 10.1.561 and above have support for MFP.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Manikanta pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Abstraction layer for peer flags is added to fix ABI breakage.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch replaces multiple if conditional checks with a single if condition
in WMI management rx handler. Found during code review.
Signed-off-by: Manikanta Pubbisetty <manikanta.pubbisetty@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWLzQ5AAoJEG4XJFUm622btRwH/A6fS7p5uSZzH5lIU8ZBLc7X
MzC1jYVepHXaR5+OhBIbQ5oSo47Y4xqMeO2ylFMpUSg4vntqR9yZNVH2lXV5EfPB
fIaGYIsb3ExjAFoIjFUBwqSOB7CCZK5myk+SLiOu9XghjsLObP5JLKgA49PGhFRn
CCuDq9diDNeJBnVzTS1ms5wO6RmOBiizzjbu7adJI0Hu63z2+P4pNMG4Zz6E1z97
z8DRFEwdNN9gKHIaEC61h7ZT9XDB/Tj31Wl3Irbi4GBS7sRXnFK46FYU8fMVDbDZ
ykj05sq6nTrfwfVZtXbV3SxlYNSN4SFFRuskon6IUcIzlNTuIULgvlpCjJJ6tyQ=
=pFoQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch disables PCI PS for QCA988X and QCA99X0, Since PCI PS is
validated for QCA6174, let it be enabled only for QCA6174. It would be
better to execute PCI PS related functions only for the supported devices.
PCI time out issue is observed with QCA99X0 on x86 platform, We will
disable PCI PS for QCA988X and QCA99X0 until PCI PS is properly implemented.
Taking and releasing ps_lock is causing higher CPU consumption. Michal Kazior
suggested ps_lock overhead to be reworked so that ath10k_pci_wake/sleep
functions are called less often, i.e. move the powersave logic up (only during
irq handling, tx path, submitting fw commands) but that's a bigger change and
can be implemented later.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since polling for tx completion is handled whenever target to host
messages are received, removing the unnecessary polling mechanism for
send completion at HTC level.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since polling for received messages not supported, remove unused
dl_is_polled.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently target to host (T2H) HTT messages are received at copy engine 1.
These messages are processed by HTC layer in both host and target.
To avoid HTC level processing overhead in both host and target,
the unused copy engine 5 is being used for receiving HTT T2H messages.
This will speedup the receive data processing as well as htt tx completion.
Hence host and target copy engine configuration tables are updated
to enable CE5 pipe. The in-direction HTT mapping is now pointing to CE5
for all HTT T2H.
Moreover HTT send completion messages are polled from HTC handler
as CE 4 is not interrupt-driven. For faster tx completion, CE4 polling
needs to be done whenever CE pipe which transports HTT Rx (target->host)
is processed. This avoids overhead of polling HTT messages from HTC
layer. Servicing CE 4 faster is helping to solve "failed to transmit
packet, dropping: -105".
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some special copy engines delivers messages directly to HTT by
bypassing HTC layer. Hence exporting tx_completion and rx_handler
for delivering the data to HTT layer.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Register receive callbacks for every copy engines (CE) separately
instead of having common receive handler. Some of the copy engines
receives different type of messages (i.e HTT/HTC/pktlog) from target.
Hence to service them accordingly, register per copy engine receive
callbacks.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Register send completion callbacks for every copy engines (CE) separately
instead of having common completion handler. Since some of the copy
engines delivers different type of messages, per-CE callbacks help to
service them differently.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Export HTC layer tx and rx handlers. This will be used by HIF layer
for per-CE data processing. Instead of callback mechanism, HIF will
call appropriate upper layers API directly.
Reviewed-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The logic in the error-handling path of ath10k_mac_register() is
divergent from the logic in ath10k_mac_unregister(). Update the
ath10k_mac_register() error handling logic to align with the
ath10k_mac_unregister() logic.
Signed-off-by: Jeff Johnson <jjohnson@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
First remove the 'cooling_device#n' syslink created
for ath10k and then unregsiter from the thermal subsystem(cooling)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 uses radio specific board names based on chip id and
board id combinations. We get these IDs from the target using BMI after otp.bin
has been started.
This patch reorders the call to the function ath10k_core_fetch_board_file
so that we have OTP binary before requesting for boardid-chipid. We get this
OTP data after parsing firmware-N.bin.
[kvalo@qca.qualcomm.com: try BMI_PARAM_GET_EEPROM_BOARD_ID with
all boards and detect if command is not supported]
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA6174 needs different board files based on board type. To make it easier to
distribute multiple board files and automatically choose correct board file
create a simple TLV file format following the same principles as with FW IEs.
The file is named board-2.bin and contain multiple board files. Each board file
then can have multiple names.
ath10k searches for file board-N.bin (where N is the interface version number
for the board file, just like we for firmware files) in /lib/firmware/*, for
example for qca99x0 it will try to find it here:
/lib/firmware/ath10k/QCA99X0/hw2.0/board-2.bin
If ath10k doesn't find board-2.bin then it will fallback to the old board.bin file.
This patch adds a simple name scheme using pci device id which for now will be
used by qca6174:
bus=%s,vendor=%04x,device=%04x,subsystem-vendor=%04x,subsystem-device=%04x
This removes the old method of having subsystem ids in ar->spec_board_id and
using that in the board file name.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: simplified the file format, rewrote commit log, other smaller changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
iwlwifi
* some debugfs improvements
* fix signedness in beacon statistics
* deinline some functions to reduce size when device tracing is enabled
* filter beacons out in AP mode when no stations are associated
* deprecate firmwares version -12
* fix a runtime PM vs. legacy suspend race
* one-liner fix for a ToF bug
* clean-ups in the rx code
* small debugging improvement
* fix WoWLAN with new firmware versions
* more clean-ups towards multiple RX queues;
* some rate scaling fixes and improvements;
* some time-of-flight fixes;
* other generic improvements and clean-ups;
brcmfmac
* rework code dealing with multiple interfaces
* allow logging firmware console using debug level
* support for BCM4350, BCM4365, and BCM4366 PCIE devices
* fixed for legacy P2P and P2P device handling
* correct set and get tx-power
ath9k
* add support for Outside Context of a BSS (OCB) mode
mwifiex
* add USB multichannel feature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWF9ciAAoJEG4XJFUm622bVaAH/3Fi4CaKrDF6L8lxSRWUZzft
Ie2X0FC+d5knpS7dOd7iI02MuEuKCg3f6dmtDrCDFBqFohvfO5NkG4XU81jdIiWM
Xkyxlgcy/1TuILNjQfNh/2nhjpvvHDCyptl+jimeT2VR2ITD/Vj3IOAMA5l4khyx
OeWmgW7dT9xLwYYy20ql5QLGkbxwJlHawUw/d+3yiS+AHO+6dVGJL2OtpyrlPP/F
0KpSj0lZY9UNRL+i6FbONDCBYeG+q/lA5G5nGXBF6zEeZ6BcuWNRcBBGr2n/6uMy
gQMAunqBIunfYkfpEKYEPF5zoyO/wCmvPLxx56iS8okGSVw4KzQ2DtQ0leFbjBw=
=1po3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
iwlwifi
* some debugfs improvements
* fix signedness in beacon statistics
* deinline some functions to reduce size when device tracing is enabled
* filter beacons out in AP mode when no stations are associated
* deprecate firmwares version -12
* fix a runtime PM vs. legacy suspend race
* one-liner fix for a ToF bug
* clean-ups in the rx code
* small debugging improvement
* fix WoWLAN with new firmware versions
* more clean-ups towards multiple RX queues;
* some rate scaling fixes and improvements;
* some time-of-flight fixes;
* other generic improvements and clean-ups;
brcmfmac
* rework code dealing with multiple interfaces
* allow logging firmware console using debug level
* support for BCM4350, BCM4365, and BCM4366 PCIE devices
* fixed for legacy P2P and P2P device handling
* correct set and get tx-power
ath9k
* add support for Outside Context of a BSS (OCB) mode
mwifiex
* add USB multichannel feature
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current number of spatial streams used by the client is advertised
as a separate IE in assoc request. Use this information to set
the NSS operating mode.
Fixes: 45c9abc059 ("ath10k: implement more versatile set_bitrate_mask").
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After processing received packets from copy engine, host will allocate
new buffer and queue them back to copy engine ring for further
packet reception. On post rx processing path, skb allocation and
dma mapping are unnecessarily handled within ce_lock. This is affecting
peak throughput and also causing more CPU consumption. Optimize this
by acquiring ce_lock only when accessing copy engine ring and moving
skb allocation out of ce_lock.
In AP148 platform with QCA99x0 in conducted environment, UDP uplink peak
throughput is improved from ~1320 Mbps to ~1450 Mbps and TCP uplink peak
throughput is increased from ~1240 Mbps (70% host CPU load) to ~1300 Mbps
(71% CPU load). Similarly ~40Mbps improvement is observed in downlink
path.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is noticed that pci wakeup time is exceeding current timeout (10ms)
randomly which is tested on QCA988x. So, the wake up time is increased
to 30 ms and added debug prints to log total timeout.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k driver is using dma_pool_alloc per packet and dma_pool_free
in coresponding at Tx completion.
Use of pre-allocated DMA buffer in Tx will improve saving CPU resource
by 5% while it consumes about 56KB memory more as trade off.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k is using Native WiFi mode as default mode for both of
Tx and Rx path, but it could be changed when driver registers
with a module parameter for specific purpose such as mesh.
The Rx decap mode sent to firmware during WMI initialization should
use the same mode that driver configured at its registration stage
in case of using raw mode, so that host driver receives MAC frame
header containing necessary fields such as QoS and Mesh Control
and uses them in right way to make data traffic work.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.
Example usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel 5180 mode 10
CTL = 0x10 Reg. Domain = 58
Antenna Gain = 1 Reg. Max Antenna Gain = 0
Power Limit = 34 Reg. Max Power = 34
Num tx chains = 3 Num supported rates = 155
**********CDD POWER TABLE*******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
1 CCk 0x41 0 0 0
[...]
154 HTCUP 0x 0 24 0 0
**********STBC POWER TABLE******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
[...]
154 HTCUP 0x 0 24 24 0
**********TXBF POWER TABLE******
is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy a_sle32_to_cpu() from ath6kl so that we can easily handle signed __le32
values. This is needed in struct wmi_pdev_tpc_config_event.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
checkpatch found:
drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
drivers/net/wireless/ath/ath10k/wmi.c:3023: void function return statements are not generally useful
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
drivers/net/wireless/ath/ath10k/htt_tx.c:457: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/htt_tx.c:545: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/mac.c:200: braces {} are not necessary for single statement blocks
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
checkpatch found:
drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
checkpatch found:
drivers/net/wireless/ath/ath9k/core.c:490: Logical continuations should be on the previous line
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of qca99x0 and MSI-X supported/enabled we
failed during interrupts registering with message:
ath10k_pci 0000:04:00.0: failed to request MSI-X ce irq 50: -22
Issue/fix was reproduced/tested using Dell Latitude E6430 laptop.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ldpc is not configured for fixed rates. This blocks auto rate vs fixed
rate performance comparison. Since firmware is considering ldpc vdev
param for fixed rate selection, it has to be configured to enable ldpc
for fixed rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some platforms really don't like DMA bursts of 256 bytes, and this
causes the firmware to crash when sending beacons.
Also, changing this based on the firmware version does not seem to make
much sense, so use 128 bytes for all versions.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was missed in the original commit adding the flag and ath10k only printed "bit10":
ath10k_pci 0000:02:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.70.6-2 api 3
htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 features no-p2p,bit10
Also add a build test to avoid this happening again.
Fixes: ccec9038c7 ("ath10k: enable raw encap mode and software crypto engine")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vdevs associated with a given chanctx should be
restarted if the bandwidth changes. Otherwise
traffic may cease.
This is known to fix STA CSA with bandwidths wider
than 20MHz.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary to make vdev restarting logic
reusable later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The remain_on_channel callback needs different
timeout. Calling ieee80211_queue_work() with a
shorter delay after calling it with a longer delay
will not change the timer. This caused the
offchannel timeout worker to not trigger in time
and caused the device to stay on channel longer
then expected. This could cause some problems and
was be easily reproduced with `iw offchannel`
command.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for mesh to ath10k. We simply use an AP virtual interface
in the firmware in order to enable beaconing without TSF adoption, and
use the raw (802.11) transmit mode.
Due to firmware limitations, the firmware must operate in raw
(non-native 802.11) mode. As this is configured at firmware init time,
a new "rawmode" modparam is added, and mesh interfaces are available
only if rawmode=true. The firmware must advertise support for rawmode;
tested successfully with firmware 10.2.4.70.6-2.
When the module is loaded with (newly implemented) modparam rawmode=1, it
will enable operating an open mesh STA via something like the following:
ip link set wlan0 down
iw dev wlan0 set type mp
ip link set wlan0 up
iw dev wlan0 set freq 5745 80 5775
iw dev wlan0 mesh join mesh-vht
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the case of raw mode without nohwcrypt parameter, we
should still make sure the frame is protected before
adding MIC_LEN to avoid skb_under_panic errors.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, ath10k restricts received frames to those matching BSSID.
When other BSS frames are requested (e.g. in mesh mode), add an internal
monitor device so those frames are not filtered.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes hardware reports invalid mcs index in rx descriptor
when operating in VHT80 mode and all packets with invalid mcs
will be eventually dropped in mac80211. This issue is observerd during
testing on QCA99X0 chipsets.
This patch adds a warn message for dumping the rx desc info which helps
in analysing the issue when invalid mcs is received.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Similarly to the VHT STS, this is supposed to be propagated by firmware.
In case it's not, use the default value, but as last resort.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The VHT STS CAP shall be reported by firmware to host, like in case of
QCA99x0. For QCA6174 hw family this isn't set for some reason.
So for this particular chips, let's assume it has the ability to
support VHT NDP in up to 4 STSs (which is true by the way).
Change the published beamformee STS cap accordingly to 3 or to what
the firmware reports.
Assumption so far, it suppose to be the num_rf_chains-1, was
completely wrong.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In a noisy environment, when multiple interfaces are created,
the management tx descriptors are fully occupied by the probe
responses from all the interfaces. This prevents a new station
from a successful association.
Fix this by limiting the probe responses when the specified
threshold limit is reached.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During long hours of stress testing like AP interface up/down along
with continuous ping flood from a station doing connect/disconnect,
it is observed that the system is not able to allocate DMA consistent
memory of size > 512KB chunks as requested by firmware in WMI_SERVICE_EVENTID.
With the system memory getting fragmented during the run based on the
size of the memory requested, the failure to return physically continguous
memory of high order can happen. Once the system gets to this situation,
bringing up the wifi interface will fail and a system reboot may be needed
to make it work again. This problem is obseved with QCA99X0.
To fix this issue, allocate the DMA memory requested by firmware during
device probe time and keep it during the life time of the device. WMI service
ready event handler is changed to allocate the memory chunks if it is
not already allocated or if the memory allocated for the previous ready
event is not same as the current requested ones. After this patch the
memory usage when wifi is inactive will be inceased by few 100KB to
3MB based on the target type.
Failure happens with the following stack trace
[29557.488773] kworker/u4:1: page allocation failure: order:8, mode:0xd0
[29557.494297] CPU: 0 PID: 8402 Comm: kworker/u4:1 Not tainted 3.14.43 #7
[29557.500793] Workqueue: ath10k_aux_wq ath10k_wmi_event_service_ready_work [ath10k_core]
[29557.508602] [<c021e9b0>] (unwind_backtrace) from [<c021ba90>] (show_stack+0x10/0x14)
[29557.516580] [<c021ba90>] (show_stack) from [<c03bdddc>] (dump_stack+0x88/0xcc)
[29557.523612] [<c03bdddc>] (dump_stack) from [<c0290e34>] (warn_alloc_failed+0xdc/0x108)
[29557.531515] [<c0290e34>] (warn_alloc_failed) from [<c0292d88>] (__alloc_pages_nodemask+0x4f0/0x654)
[29557.540485] [<c0292d88>] (__alloc_pages_nodemask) from [<c0222b48>] (__dma_alloc_buffer.isra.20+0x2c/0x104)
[29557.550260] [<c0222b48>] (__dma_alloc_buffer.isra.20) from [<c0222c34>] (__alloc_remap_buffer.isra.23+0x14/0xb8)
[29557.560413] [<c0222c34>] (__alloc_remap_buffer.isra.23) from [<c022305c>] (__dma_alloc+0x224/0x2b8)
[29557.569490] [<c022305c>] (__dma_alloc) from [<c0223208>] (arm_dma_alloc+0x84/0x90)
[29557.577010] [<c0223208>] (arm_dma_alloc) from [<bf5159d0>] (ath10k_wmi_event_service_ready_work+0x2f8/0x420 [ath10k_core])
[29557.588055] [<bf5159d0>] (ath10k_wmi_event_service_ready_work [ath10k_core]) from [<c024260c>] (process_one_work+0x20c/0x328)
[29557.599305] [<c024260c>] (process_one_work) from [<c02432d0>] (worker_thread+0x228/0x360)
[29557.607470] [<c02432d0>] (worker_thread) from [<c0247f88>] (kthread+0xd8/0xec)
[29557.614750] [<c0247f88>] (kthread) from [<c0208d18>] (ret_from_fork+0x14/0x3c)
[29557.712751] Normal: 696*4kB (UEMR) 512*8kB (UEMR) 367*16kB (UEMR) 404*32kB (UEMR) 455*64kB (UEMR) 424*128kB (UEMR) 379*256kB (UMR) 327*512kB (UMR) 1*1024kB (R) 0*2048kB 0*4096kB = 374544kB
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
MU-MIMO Rx involves different interpretation of
the VHT-SIG-A compared to SU-MIMO.
The incorrect interpretation led ath10k to report
VHT MCS values greater than 9 which subsequently
prompted mac80211 to drop such frames. This
effectively broke Rx with MU-MIMO in many cases
and manifested with a kernel warning in the log
which looked like this:
[ 14.552520] WARNING: CPU: 2 PID: 0 at net/mac80211/rx.c:3578 ieee80211_rx+0x26c/0x940 [mac80211]()
[ 14.552522] Rate marked as a VHT rate but data is invalid: MCS: 10, NSS: 2
... call trace follows ...
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67 ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.
Fixes: e04cafbc38 ("ath10k: fix peer limit enforcement")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If .pull_fw_stats() fails for some reason while processing
fw stats event, collected pdev/vdev/peer stats just before
the failure should be freed. This is unlikely to happen,
just code review catch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found incorrect sequence in ath10k_core_stop() where wmi pktlog
disable cmd is passed from ath10k_debug_stop() to firmware
immediately after wmi pdev suspend cmd. Firmware will not accept
any wmi cmd after receiving wmi pdev suspend cmd.
Fix this issue in ath10k_core_stop() by moving ath10k_debug_stop()
just before sending pdev suspend cmd. So that pktlog disable cmd
will get passed before pdev suspend cmd.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI 10.4 uses the same command interface as QCA988X for addba/delba
debug wmi commands. Fill wmi_10_4_ops table with the functions used
for QCA988X for these commands.
With this change, the following debugfs entries can be used to
configure the aggregation mode and to send addba request,
addba response and delba respectively in manual aggregation mode
for QCA99X0 chip.
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/aggr_mode
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba_resp
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header format of 10.4 firmware phyerr event is not alligned
with pre 10.4 firmware. Introduce new wmi handlers to parse
10.4 firmware specific phyerror event header.
With changes covered in this patch, radar detection works on
qca9x0 hw 2.0 which uses 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently it's not safe to install both pairwise
and groupwise keys on AP vdevs as it can cause
traffic to stop working in some multi-vif
(WPA+WEP) cases.
Fixes: ce90b27128 ("ath10k: fix multiple key static wep with ibss")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are three WMI_CHAN_INFO events reported per channel
in QCA99X0 firmware. First one is a notification at the begining
of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0),
second one is a notification at the end of the dwell time with cmd_flag
CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication
with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for
the channel. Since there is a new state before the completion, the handler
is to fixed so that the counts are deducted from the ones reported with
CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE.
Without this fix there will be lots of 0 msecs reported as active
and busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vif's vdev_id is used as queue number. However due
to the tx pausing design in ath10k it was possible
for a new interface to be created with its tx
queue stopped (via ieee80211_stop_queues). This
could in turn leave the interface inoperable until
ath10k_mac_tx_unlock() was called.
This problem only affected multi-vif scenarios when
new interfaces were created some time later after
other interfaces have been running for some time
and had Tx queue full at some point prior.
Possible manifestation of the bug was
authentication timeout for a client vif.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once HTT Tx queue got full offchannel queue was
stopped and never woken up again. This broke, e.g.
P2P. This could be reproduced after running a lot
of traffic enough to saturate 100% of the driver
Tx queue and then trying to send offchannel
traffic.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec ("ath10k: allocate fw resources for iface combinations")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If peer creation failed during offchannel Tx the
driver attempted to delete the peer nonetheless.
This caused the ar->num_peers counter to be
incorrectly decremented. This subsequently could
cause the counter to drop below 0 and also
eventually lead to firmware crash because host
would think there are less peer entries created in
firmware then there really were.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WoWLAN resume fails with retval 1 mac80211
will attempt to reconfig the device in a similar
manner when hw restart is requested. This wasn't
handled properly and yielded call trace warnings
and the device ended up not working.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Initial QCA99X0 support has a known issue with TCP Tx throughput.
All other path such as UDP Tx/Rx and TCP Rx meet their expectation
(> 900Mbps), but TCP Tx marked as low as 5Mbps when single pair is
used on iperf.
The root cause is turned out because TSO flag is not initialized
properly so that firmware configures TSO in wrong way.
TSO flags in msdu extension descriptor is required to be reset
to indicate firmware there is no TSO is enabled, otherwise it
could act as TSO is enabled which causes huge throughput drop.
In fact, it's enough by resetting TSO flags only to prevent the
unexpected behavior, but initializing whole msdu ext. descriptor
will help to clear uncertainty of firmware could bring on as it
constantly updated.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add vendor/device id of QCA99X0 V2.0 to pci id table and
QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
QCA99X0 to get detected by the driver.
kvalo: now QCA99X0 family of chipsets is supported by ath10k.
Tested client, AP and monitor mode with QCA9990.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When max client was set to 512 in qca99x0, there was host memory
alloc failure during wmi service ready event handling. This issue
got resolved now, increasing max client limit from 256 to 512.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Host memory required for firmware is allocated while handling
wmi service ready event. Right now, wmi service ready is handled
in tasklet context and it calls dma_alloc_coherent() with atomic
flag (GFP_ATOMIC) to allocate memory in host needed for firmware.
The problem is, dma_alloc_coherent() with GFP_ATOMIC fails in
the platform (at least in AP platform) where it has less atomic
pool memory (< 2mb). QCA99X0 requires around 2 MB of host memory
for one card, having additional QCA99X0 card in the same platform
will require similarly amount of memory. So, it's not guaranteed that
all the platform will have enough atomic memory pool.
Fix this issue, by handling wmi service ready event in workqueue
context and calling dma_alloc_coherent() with GFP_KERNEL. mac80211 work
queue will not be ready at the time of handling wmi service ready.
So, it can't be used to handle wmi service ready. Also, register work
gets scheduled during insmod in existing ath10k_wq and waits for
wmi service ready to completed. Both workqueue can't be used for
this purpose. New auxiliary workqueue is added to handle wmi service
ready.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables raw Rx/Tx encap mode to support software based
crypto engine. This patch introduces a new module param 'cryptmode'.
cryptmode:
0: Use hardware crypto engine globally with native Wi-Fi mode TX/RX
encapsulation to the firmware. This is the default mode.
1: Use sofware crypto engine globally with raw mode TX/RX
encapsulation to the firmware.
Known limitation:
A-MSDU must be disabled for RAW Tx encap mode to perform well when
heavy traffic is applied.
Testing: (by Michal Kazior <michal.kazior@tieto.com>)
a) Performance Testing
cryptmode=1
ap=qca988x sta=killer1525
killer1525 -> qca988x 194.496 mbps [tcp1 ip4]
killer1525 -> qca988x 238.309 mbps [tcp5 ip4]
killer1525 -> qca988x 266.958 mbps [udp1 ip4]
killer1525 -> qca988x 477.468 mbps [udp5 ip4]
qca988x -> killer1525 301.378 mbps [tcp1 ip4]
qca988x -> killer1525 297.949 mbps [tcp5 ip4]
qca988x -> killer1525 331.351 mbps [udp1 ip4]
qca988x -> killer1525 371.528 mbps [udp5 ip4]
ap=killer1525 sta=qca988x
qca988x -> killer1525 331.447 mbps [tcp1 ip4]
qca988x -> killer1525 328.783 mbps [tcp5 ip4]
qca988x -> killer1525 375.309 mbps [udp1 ip4]
qca988x -> killer1525 403.379 mbps [udp5 ip4]
killer1525 -> qca988x 203.689 mbps [tcp1 ip4]
killer1525 -> qca988x 222.339 mbps [tcp5 ip4]
killer1525 -> qca988x 264.199 mbps [udp1 ip4]
killer1525 -> qca988x 479.371 mbps [udp5 ip4]
Note:
- only open network tested for RAW vs nwifi performance comparison
- killer1525 (qca6174 hw2.2) is 2x2 device (hence max 866mbps)
- used iperf
- OTA, devices a few cm apart from each other, no shielding
- tcpX/udpX, X - means number of threads used
Overview:
- relative Tx performance drop is seen but is within reasonable and
expected threshold (A-MSDU must be disabled with RAW Tx)
b) Connectivity Testing
cryptmode=1
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br OK
ap=iwl6205 sta1=qca988x crypto=open topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wep1 topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa topology-1ap1sta2br1vlan OK
ap=iwl6205 sta1=qca988x crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=open topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wep1 topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa topology-1ap1sta2br1vlan OK
ap=qca988x sta1=iwl6205 crypto=wpa-ccmp topology-1ap1sta2br1vlan OK
Note:
- each test takes all possible endpoint pairs and pings
- each pair-ping flushes arp table
- ip6 is used
c) Testbed Topology:
1ap1sta:
[ap] ---- [sta]
endpoints: ap, sta
1ap1sta2br:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
endpoints: veth0, veth2, br0, br1
note: STA works in 4addr mode, AP has wds_sta=1
1ap1sta2br1vlan:
[veth0] [ap] ---- [sta] [veth2]
| | | |
[veth1] | \ [veth3]
\ / \ /
[br0] [br1]
| |
[vlan0_id2] [vlan1_id2]
endpoints: vlan0_id2, vlan1_id2
note: STA works in 4addr mode, AP has wds_sta=1
Credits:
Thanks to Michal Kazior <michal.kazior@tieto.com> who helped find the
amsdu issue, contributed a workaround (already squashed into this
patch), and contributed the throughput and connectivity tests results.
Signed-off-by: David Liu <cfliu.tw@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During tx completion, tx_lock is held for longer than required, preventing
efficient refill of htt->pending_tx. Refactor the code so that only MSDU
related operations are protected by the lock.
Improves downstream performance on a dual-core ARM Freescale LS1024A
(f.k.a. Mindspeed Comcerto 2000) AP with a 3x3 client from 495 to 580 Mbps.
Other CPU bound multicore systems may also benefit.
Signed-off-by: Denton Gentry <dgentry@google.com>
Signed-off-by: Avery Pennarun <apenwarr@google.com>
[mfaltesek@google.com: removed conflicting code for tracking msdu_ids.]
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using DFS channels on Ath10k, kernel log has repeated warning message
'failed to process fft: -22' typically under medium/heavy traffic.
This patch switches the warnings to driver debug (WMI events) mode only
thus reducing log file noise.
DFS and spectral scan share underlying HW mechanisms and enabling one
(DFS) enables the other (spectral scan) as far as event reporting from
firmware to driver is concerned. Spectral scan events take no part in
processing of DFS radar pulses which are delivered as distinct events,
so the fft (spectral event) warning is harmless and DFS interference
detection/protection still occurs.
Symptoms seen & fix tested in both debug & non-debug modes on TP-Link
Archer C7 v2 platform.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT_H2T_MSG_TYPE_MGMT_TX msg in 10.4 firmware carries additional
4 byte in htt_mgmt_tx_desc where it tells to firmware that at what
rate mgmt frame has to go out in the air. It's an optional parameter,
setting this field to zero will force firmware to choose auto rate
and send the frame out.
Those 4 byte info is missed out in the current code and 10.4 firmware
ended up reading some junk in those 4 byte and sometime malfunctioning.
Fix it by adding 4 byte in struct htt_mgmt_tx_desc. Non 10.4 firmware
will not process those four byte. So, adding 4 byte at the end of
struct htt_mgmt_tx_desc will not create any impact on other chipset.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch adds support to offload TCP/UDP checksum
calculations for QCA99x0.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
chandef is initialized with NULL and on the very next line, we are using it to
get channel, which is not correct. Channel should be initialized after
obtaining chandef.
Found by cppcheck:
ath/ath10k/mac.c:839]: (error) Possible null pointer dereference: chandef
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 chip has an extra 4 bytes in rx_msdu_start,
20 bytes in rx_msdu_end and 20 bytes in rx_ppdu_end structure
which are used in htt_rx_desc and HTT Rx ring offset setup.
This is necessary for correct Rx for QCA99X0 or Rx descriptors
will be overwritten and corrupted.
With this patch QCA988X and QCA6174 will have extra 44 bytes
padding in Rx descriptor layout which is harmless.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rx_ppdu_end_common structure is valid for both of qca998x and
qca6174, but not for qca99x0 since it has new additional members.
Hence update the common structure to cover qca99x0 as well.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since QCA99X0 uses fragmentation descriptor differently from
other ones on tx path, we need to handle it separately.
QCA99X0 is using 48 bits for address and 16 bits for length
out of 2 dword and each values have to be programmed by frag
desc base addr + msdu id, so that hardware can retrieve
corresponding frag data.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is observed that during cold reset pcie access right
after a write operation to SOC_GLOBAL_RESET_ADDRESS causes
Data Bus Error and system hard lockup. The reason
for bus error is that pcie needs some time to get
back to stable state for any transaction during cold reset. Add
delay of 20 msecs after write of SOC_GLOBAL_RESET_ADDRESS
to fix this issue. This patch is tested on QCA988X. This is
also tested on QCA99X0 which is WIP.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.
Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.
This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.
Fixes: b4aa539dd8 ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.
Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf9844636 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.
This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.
Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 418ca5992e ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.
Fixes: 418ca5992e ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit a521ee983d ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.
User experience was a failing boot up sequence (crashing device during
initialization):
[ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70
Fix it by updating the address with correct value.
Fixes: a521ee983d ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pre qca99X0 chipsets follows the model where dynamically allocate
memory for frag desc on getting new skb for TX. But, this is not
going to be the case in qca99X0. It expects frag desc memory to be
allocated at boot time and let the driver to reuse allocated memory
after every TX completion. So there won't be any dynamic frag memory
memory allocation in qca99X0 during data transmission.
qca99X0 hardware doesn't need fragment desc address to be programmed
in msdu descriptor for every data transaction. It needs to know only
starting address of fragment descriptor at the time of the boot.
During data transmission, qca99X0 hardware can retrieve corresponding
frag addr by adding programmed frag desc base addr + msdu id.
Allocate continuous fragment descriptor memory (same size as number of
descriptor) at the time of target initialization and configure allocated
dma address to the target via HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG.
How this is allocated continuous memory is going to be used is not
covered in this patch. It just allocates memory and hand over to firmware.
If we don't do it at init time, qca99X0 will stall when firmware tries
to do TX.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 fw supports upto 4 spatial stream. Limit max spatial
stream to 4 for 10.4 firmware and to 3 for non 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 fw supports upto 16 interface in ap mode and 1 interface
in station mode, overall total interfaces supported are 16
interfaces. Populate this limit in wiphy->iface_combinations.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New htt event table is added for 10.4 firmware. Following new htt
events are available only 10.4. adding this to generic htt event
table,
HTT_T2H_MSG_TYPE_EN_STATS,
HTT_T2H_MSG_TYPE_TX_FETCH_IND,
HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing non 10.4 firmware scan related events and commands are
matching with 10.4 firmware (except chan info event). Link general
start scan,stop scan, scan channel list configuration functions
to 10.4 wmi function table and add a new handler to parse 10.4
specific chan info event.
10.4 firmware has extra scan completion reason
WMI_SCAN_REASON_INTERNAL_FAILURE and new scan event
WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT compared to previous firmware
versions. These things are added in respective enum.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Most of existing vdev and peer related functions (vdev create,
vdev delete, vdev start, peer create, peer delete, peer flush, etc)
are reusable for 10.4 firmware. Link those general vdev and peer
functions to 10.4 wmi function table.
Existing general pktlog enable/disable, dbglog configuration functions
are reusable for 10.4 and add them also in wmi function table.
Also handle few wmi events (sevice rdy, echo, dbg msg, tbtt offset
update, dbg print) in ath10k_wmi_10_4_op_rx(). wow event is not
applicable in 10.4 firmware, have it under not implemented print.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware swba event payload has space to accommodate upto
512 client traffic indication info & one p2p noa descriptor.
It's is not matching with exiting swba event format defined for
non 10.4 firmware. Non 10.4 firmware swba event format is designed
to support only upto only 128 client and four p2p notice of absence
descriptor.
following changes are done in this patch to enable ath10k to handle
10.4 firmware swba event,
- link generic ath10k_wmi_event_host_swba() to handle 10.4 swba
event in 10.4 wmi rx handler.
- add 10.4 specific swba event structure wmi_10_4_host_swba_event.
- new function ath10k_wmi_10_4_op_pull_swba_ev() to parse
10.4 swba event.
- increase tim_bitmap[] size in ath10k_vif to 64 to hold 512 station
power save state.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to 512 client support in 10.4 firmware, size of tim ie is going
to be slightly higher than non 10.4 firmware. So, size of tim_bitmap
what is carried in swba event from 10.4 firmware is bit higher.
The only bottle neck to reuse existing swba handler
ath10k_wmi_event_host_swba() for 10.4 is that code designed to deal
with fixed size tim bitmap(ie, tim_info[].tim_bitmap in wmi_swba_ev_arg).
This patch removes such size limitation and makes it more suitable
to handle swba event which has different size tim bitmap.
All existing swba event parsing functions are changed to adapt this
change. Actual support to handle 10.4 swba event is added in next patch.
Only preparation is made in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reuse existing function ath10k_wmi_op_pull_rdy_ev()
to parse WMI_10_4_READY_EVENTID and handle the same
event in ath10k_wmi_10_4_op_rx().
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware supports upto 512 clients when qcache feature is enabled.
Make adjustment on default max peer count, active peers, number of tid in
such case to meet qcache requirement. 10.4 fw has extra unit info flag
NUM_UNITS_IS_NUM_ACTIVE_PEERS which is also handled in this patch.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware wmi mgmt rx event format differs from non 10.4
firmware and changing existing wmi mgmt rx event parsing function
ath10k_wmi_op_pull_mgmt_rx_ev() for 10.4 would add more complex.
This patch adds new function to receive any wmi rx event from
10.4 firmware and also introduce new function to parse wmi mgmt
rx event.
In addition, fw main branch service rdy event parsing function
is linked in wmi ops table.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define 10.4 wmi init command structure and introduce new function
ath10k_wmi_10_4_op_gen_init() to fill default values for each field
which goes as part of wmi init cmd to 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include 10.4 firmware wmi pdev cmd id and prepare wmi vdev map
table wmi_10_4_pdev_param_map and update non 10.4 firmware
pdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include 10.4 firmware wmi vdev cmd id and make up wmi vdev map
table wmi_10_4_vdev_param_map and also update non 10.4 firmware
vdev cmd map table with newly added vdev cmd id specifically for
10.4 firmware as unsupported.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In fact, explicit assigned to ZERO for unsupported wmi commands
are not really needed. Global static variable will have ZERO by
default. However, just for better readability setting all wmi cmds
in non 10.4 firmware wmi mapping table as unsupported for wmi cmd
which are exclusively available only in 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware wmi cmd and event id values are not exactly aligned
with previous firmware versions (main, 10.x, 10.2, etc). Add new
enum to define wmi cmd & event definitions for 10.4 firmware and
prepare wmi_10_4_cmd_map based on 10.4 firmware wmi cmd definitions.
wmi_cmd_map is extended to accommodate new wmi commands which are
exclusively available in 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Include new enum to define wmi service bitmap definitions for
10.4 firmware and a function wmi_10_4_svc_map() to remap 10.4
firmware wmi service bitmap definitions to ath10k generic wmi
services.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca99X0 chip uses firmware version 10.4. Define a new macro
ATH10K_FW_WMI_OP_VERSION_10_4 for 10.4 firmware and include
in switch cases where ATH10K_FW_WMI_OP_VERSION_* is used
to avoid compilation error.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
BMI parameter value to execute downloaded otp binary
is different for QCA99X0. Have a member in hw_params
to hold hw specific BMI param.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is more than 1 sec delay in getting response from target
through BMI in QCA99X0. Increase the BMI communication timeout
to 2*HZ to fix BMI failures.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVglpWAAoJEG4XJFUm622bkT0H+QE/T3i44l6SEAxHEgW6Z2JP
MsAVHFV8q2jPCGfg4oCozk3fo2WPdBKwhUy7xzAg/LfxuTn0CtIzl+KuEnhsBBsx
+cNBFgBzIvHaMwfb/vxmuLK7zUROtDgOK7Kt4HF9p/Mn/JH8yTCrRy96hpnVKnuQ
h6HFO8Qx0l0pd6lbosaSPvjM8qBPy3ZfvriEHV3BTV+AXgSPWwnFkY188G2CNK5J
yYK0C2PkEX368m/qpmcbhlYrn3ZiJviiWhFmQZMW8eXe0k/pfBidXt6QGmKA7loT
p09skJk+qQtZjK4p2Hzy/3KOLU7YGFVHzww5gXqrZSxhluyhEdbOVLvKfB5jR68=
=3lke
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_event_timeout(), introduced in 'commit 5e3dd157d7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to force an out of bounds MMIO
read/write via debugfs. E.g. on QCA988X this could
be triggered with:
echo 0x2080e0 | tee /sys/kernel/debug/ieee80211/*/ath10k/reg_addr
cat /sys/kernel/debug/ieee80211/*/ath10k/reg_value
BUG: unable to handle kernel paging request at ffffc90001e080e0
IP: [<ffffffff8135c860>] ioread32+0x40/0x50
...
Call Trace:
[<ffffffffa00d0c7f>] ? ath10k_pci_read32+0x4f/0x70 [ath10k_pci]
[<ffffffffa0080f50>] ath10k_reg_value_read+0x90/0xf0 [ath10k_core]
[<ffffffff8115c2c1>] ? handle_mm_fault+0xa91/0x1050
[<ffffffff81189758>] __vfs_read+0x28/0xe0
[<ffffffff812e4694>] ? security_file_permission+0x84/0xa0
[<ffffffff81189ce3>] ? rw_verify_area+0x53/0x100
[<ffffffff81189e1a>] vfs_read+0x8a/0x140
[<ffffffff8118acb9>] SyS_read+0x49/0xb0
[<ffffffff8104e39c>] ? trace_do_page_fault+0x3c/0xc0
[<ffffffff8196596e>] system_call_fastpath+0x12/0x71
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable VHT support for IBSS, while mac80211/cfg80211 and
wpa_supplicant already support this.
In my test env, qca988x 2x2 I get:
(udp) ath10k-1 >>>> ath10k-2 (server) - speed: 419 Mbits/sec
(tcp) ath10k-1 >>>> ath10k-2 (server) - speed: 404 Mbits/sec
During tests I used wpa_supplicant (latest git version), which
already support IBSS VHT, and choose highest available BW. Also tested with
qca6174.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT version itself isn't sufficient to know what
HTT version given firmware blob uses. Hence print
the recently introduced HTT op version code.
While at it make the info string a bit more
consistent and clear.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This should help when analysing problems from
users and spot fw api blob problems easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Found during code review. This was pretty much
impossible to happen but better safe than sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the midst of chanctx patch review channel
switching became broken which I failed to notice
until now.
Function ath10k_mac_vif_chan() reports current
chandef which isn't updated until after
switch_vif_chanctx() is returned from.
Consequently the driver just restarted operation
on channels it was residing already instead of
switching to the new ones.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In practice there's no point in having a copy of
chanctx_conf.
Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().
The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Channel contexts aren't iterable until after
they've been added to the driver. The code assumed
otherwise.
This problem could result in:
* rx_channel being NULL and forcing Rx path to go
the slow way to get channel on QCA988X,
* report incorrect channel when running
multi-channel on QCA61X4 hw2.1,
* report incorrect channel after AP channel
switch.
Fixes: 500ff9f938 ("ath10k: implement chanctx API")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.
Fixes: d84a512dca ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When wmi mgmt event function fails to parse given skb,
it should be freed on failure condition to avoid memory
leaks. Found this during the code review.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXbP3AAoJEG4XJFUm622b5KoH/1qlTHsKcyvdxlhQOgYNGCXA
HNMwcxtwFyRYHFeVTGOQp2BVknEoqWTwGv1m4FQ1pBSSwuUvAyw4BHNSRat/zaNc
wLnZgUYKH5VHeoE/cpe/Asowau+u8hru1adPsVSjudTXMinKrNaDUfjSs2U+UR0+
BaC3PtsANk7wH82+bZq3qXYjcaZITObDe3WBmMNMG0nTimS6pScgnTUnfHch+CEA
0sTOlZF+QTGiH/c5tw2SAoRft4OG+oTnWYQ+vEEQsVev7Yegasa/kg4NdDVdjBNk
9VH9aDlQfGgxodCoeJuQCDzUZL8ixnvYTLeUTxqypzx9Cw0TsLDwoMQA+Ux3G8w=
=JSya
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.
Currently the sleep threshold/grace period is at a
very conservative value of 60ms.
Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.
Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.
The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.
This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is actually safe to enable ASPM after the
device is booted up.
This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx clear count reported in wmi_chan_info_event is actually channel_busy_count
not rx_frame_count. Send rx_clear_count through time_busy of survey_info
and set SURVEY_INFO_TIME_BUSY in filled.
iw wlan0 survey dump
urvey data from wlan0
frequency: 5180 MHz [in use]
noise: -103 dBm
channel active time: 150 ms
channel busy time: 22 ms
Survey data from wlan0
frequency: 5200 MHz
noise: -102 dBm
channel active time: 146 ms
channel busy time: 0 ms
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral scan supported by ath10k has capability to monitor and report
through whole bands and channels, but current buffer size is too small
to save reported spectral scan data.
This results in dropping 5G channel reports at all when dual band card
is used, so that users are not able to analyze spectral environments.
Hence increase the buffer size to fix the problem.
A spectral data size is vary based on the number of bins, so the unit
buffer size, 1140, is chose to minimize relay buffer fragmentation.
The total buffer size is also chose in tradeoff with spectral scan
support vs. kernel memory consumption.
Since theoretical maximum buffer size, 9.5MB, can be consumed with
512 bins in dual bands, we target to cover up to 128 bins for all
channels in dual bands and due to the buffer size limitation,
spectral scan with bin number bigger than 128 needs to be run on
single band each.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.
I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes in ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
Until now only a single fixed tx rate or nss was
allowed to be set.
The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.
This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.
Depending on firmware revisions some combinations
may crash firmware so use with care, please.
This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.
These work:
iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9
These won't work:
iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
iw wlan0 set bitrates vht-mcs-5 2:7-9
(note the invalid VHT MCS ranges)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver can clearly enable fast-xmit since it does rate
control in the device and thus must do duration calculation
there as well.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During initialization firmware does some sort of
memory switch between DRAM and IRAM. If
configuration value for bank switching isn't
correct device crashes during init.
The new value prevents firmware 11.0.0.302 (and
possibly others) for qca61x4 hw2.1 from crashing
during init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices differ slightly and require different
board files. If wrong board data is used they
crash or behave incorrectly.
These devices can be differentiated by looking at
PCI subsystem device id. That is the case for
qca61x4 devices at least.
The board specific filename is constructed as:
board-<bus>-<id>.bin
For PCI in particular it is:
board-pci-<vendor>:<dev>:<subsys_vendor>:<subsys_dev>.bin
These files are looked in device/hw specific
directories. Hence for Killer 1525 (qca6174 hw2.1)
ath10k will request:
/lib/firmware/ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin
To not break any existing setups (e.g. in case
some devices in the wild already have subsys ids)
if a board specific file isn't found a generic one
is used which is the one which would be used until
now. This guarantees that after upgrading a driver
device will not suddenly stop working due to
now-missing specific board file. If this is the
case a "fallback" string is appended to the info
string when driver boots.
Keep in mind this is distinct from cal-pci-*.bin
files which contain full calibration data and MAC
address. Cal data is aimed at systems where
calibration data is stored out of band, e.g. on
nand flash instead of device EEPROM - an approach
taken by some AP/router vendors.
Board files are more of a template and needs some
bits to be filled in by the OTP program using
device EEPROM contents.
One could argue to map subsystem ids to some board
design codename strings instead of using raw ids
when building the board filename. Using a mapping
however would make it a lot more cumbersome and
time consuming (due to how patches propagate over
various kernel trees) to add support for some new
device board designs. Adding a board file is a lot
quicker and doesn't require recompilation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to implement the same thing twice.
Reduce code duplication.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new 10.2.4 FW support the BT-coex feature with external BT module,
The external BT modules can communicate with it via the GPIO. This patch
check the BT-coex capability of the FW and enable it by default.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the FW ATF (Air Time Fairness) service define to keep consistent
with 10.2 FW capability.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WLAN survey data provides several informative values on each channels
such as noise, active time, transmit time, and etc.
Regarding the channel activity time data, it is reported from firmware
in different form which is number of cycles instead of time itself.
Hence host driver converts it to time unit by dividing it by clock rate
that is used at baseband MAC.
Using difference clock rate from that actual HW is using will result in
inaccurate survey data. For instance, channel active time can be reported
with bigger than 150ms even though we set Dwell time to 150ms.
Therefore set the clock rate to 88000 (88 MHz) which is ath10k baseband
MAC is using.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With latest additions to the driver it seems
viable to enable support for IBSS-RSN.
It seems to work on QCA988X and 999.999.0.636 but
is a bit slow to exchange RSN keys for some
reason. This may be a firmware quirk or ath10k is
missing something. Nevertheless it makes sense to
finally enable IBSS-RSN in ath10k even if somewhat
handicapped.
QCA6174 firmware doesn't seem to be able to Tx
EAPOL frames at all now (they get stuck in hw
queues for some reason) so it never gets to set
the keys in driver. It's fairly safe to assume that
once this is fixed IBSS-RSN will work with QCA6174
firmware without any additional changes. Hence no
special handling for advertising
IEEE80211_HW_SUPPORTS_PER_STA_GTK and
WIPHY_FLAG_IBSS_RSN is done now.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some time ago there was a weird issue with AP
using wrong multicast keys and generating
corrupted traffic on 10.1 firmware.
Apparently a very similar problem applies for
IBSS-RSN on 999.999.0.636.
ath10k doesn't have IBSS-RSN enabled yet. This
patch is a prerequisite to support it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently firmware requires both pairwise and
groupwise keys to be installed per-peer for static
WEP in IBSS. This wasn't necessary for AP mode
(and installing both doesn't seem to break AP
mode thus there's no special handling).
Also there seems to be some kind of issue with
mapping tx/rx keys in firmware properly which
resulted in wrong keys being used and broken
communication between devices.
It can be argued the vdev param part is more of a
workaround than a real fix. However I couldn't
figure out how to fix this differently. It works
and isn't super ugly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware actually re-creates peer entry when
reassoc flag is set. This is undesired and could
cause trouble with IBSS crypto-wise. This is also
important for upcomming bitrate mask improvement.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 sets static WEP keys as groupwise while
firmware requires them to be installed twice as
both pairwise and groupwise.
Until now these keys were installed once as
pairwise only and, due to that special handling,
needed additional tricks to support 802.1x as
well.
Without this patch in some cases (when AP and
ath10k client use different default tx keys)
multicast communication was broken.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames are logged via tracing in two slices:
header and payload, separately. This is done for
performance reasons when one wants to, e.g.
analyse metadata only of frames only.
If for some reason device delivered a frame buffer
which was sized below what 802.11 header implied
tracing logic would blow doing an invalid memory
accesses.
I've hit this problem when running IBSS on QCA988X
with 999.999.0.636 and tracing at the same time.
Fixes: 5ce8e7fdcc ("ath10k: handle ieee80211 header and payload tracing separately")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If chip_id wasn't recognized clean up code wasn't
executed properly. It would skip freeing memory
causing a leak and irqs causing possibly MSI
warning splats later or even kernel crashes.
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.
Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.
This should improve P2P reliability a bit.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Use the new IEEE80211_TX_STAT_NOACK_TRANSMITTED flag
to indicate successful transmission of no-ack frames.
This fixes multicast frame accounting.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix the regerssion introduced after "ath10k_wmi_requests_stats()
call to use more stat bits", both the 10.2.X FW and community FW 10.1.X
will return time out when access the fw_stats with the STAT_VDEV and
STAT_PDEV. Add the condition to use different fw_stats mask for different
FW versions.
Fixes: 7777d8c7ef ("ath10k: implement fw stats for wmi-tlv")
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default keyidx callback may be called after
more than 1 key is installed. This led to only 1
WEP key being reinstalled only. This caused Rxed
traffic encrypted with other WEP keys to be
dropped in client mode.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The variable should be cleared regardless of
whether there's a peer associated with the key or
not.
This fixes case when user first associates with 2
WEP keys and then disconnects and connects with 1
WEP key. This resulted in WEP key count being 2 in
the driver leading to default keyidx fixup
failure.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's always at most 2 credits and it makes
little sense to set the
ATH10K_HTC_FLAG_NEED_CREDIT_UPDATE flag
conditionally.
This seems to fix some random issues with tx
credit starvation on WLAN.RM.2.0-00073 I've been
seeing. Note: this isn't related to wmi mgmt tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmwares that indicate BURST_SERVICE as enabled
could overwrite some wmm parameters (eg. txop).
This could lead IOT and balancing issues.
Hence disable this by default.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WLAN.RM.2.0-00073 firmware requires self-peer to
be created prior to issuing scan command. Without
this wmi-tlv with qca6174 firmware crashes after
submitting a scan request.
Creating the peer as soon as add_interface()
shouldn't be a problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code was a bit convoluted. Clean it up and
prepare for future changes.
While at it this fixes incorrect verification of
'single nss' case when ss2 rates were missing
while ss1 and ss3 were requested resulting in
nss=3 being set:
iw wlan1 set bitrates legacy-5 ht-mcs-5 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23 vht-mcs-5 1:0-9 3:0-9
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of 3 vdevs wasn't enough to handle the
worst case for interface combinations in practice.
wpa_supplicant may need up to 4 vifs to have 2
vifs actually connected, i.e. p2pdev + client + 2x
p2p (either p2p client or p2p go).
This fixes worst case warning:
Free vdev map is empty, no more interfaces allowed.
This keeps the ability to associate 32 stations in
AP mode at the cost of not being able to guarantee
that under all circumstances, i.e. some
combinations may consume additional fw peer
entries for internal purposes leaving less
resource for stations in AP mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This effectively enables multi-channel operation
on qca6174 WLAN.RM.2.0-00073 (and possibly any
newer firmware release for qca6174).
This adds appopriate interface combinations and
initializes firmware channel scheduler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 wmi-tlv firmware defines a new wmi event
for host tx pausing (i.e. stop/wake tx queues).
Map these events to ath10k/mac80211 tx queue
control.
This is important for multi-channel throughput
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reject a valid
firmware configuration combination.
Since SSID isn't known early on it might make
sense to allow driver to start vdev without SSID
and restart it later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 and wmi-tlv doesn't have quiet mode
implemented. Don't even attempt to call it. This
fixes a warning when bringing first interface up:
failed to set quiet mode period 100 duarion 0 enabled 0 ret -95
Fixes: 8515b5c79a ("ath10k: configure thermal throttle while powering up")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All of the bringup/init functions called in ath10k_core_start return 0
on success and != 0 on failure. ath10k_wmi_wait_for_service_ready(),
ath10k_wmi_wait_for_unified_ready() and their call sites were adjusted
to fit this model.
The return type of wait_for_completion_timeout is unsigned long not int so
ath10k_wmi_wait_for_service_ready() and ath10k_wmi_wait_for_unified_ready()
were fixed up accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Missing spaces 1*HZ -> 1 * HZ were also added along the way.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, respectively 'ret'
renamed, and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While debugging something else I noticed AID was
set to 0. This could lead to powersave issues in
station mode. Maybe this isn't really necessary
but set it properly just to be sure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't use literal values for offsets. While at it
rename a function so it is more clear what it
checks for.
This finally takes care of the last magic
5GHz/OFDM offset.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's possible to derive rate index from bitrate
without any additional mapping structures/logic.
This should have little to none impact on
performance since this is only done for management
frames and the previous approach wasn't
particularly optimized.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of using a hacky table and magic values
use supported band information advertised to
mac80211.
This may impact performance a little when dealing
with legacy rx rates depending on system
architecture. It's probably negligible.
This also fixes a highly theoretical corner case
when HT/VHT rates weren't reported correctly if
channel frequency wasn't known.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the existing ieee80211_rate array instead of
definining separate one. This gets rid of the ugly
4-index offset when dealing with 5GHz band.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using raw values is discouraged. Having
defines/enums is preferred.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was superfluous and confusing. It's better to
define the structure explicitly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to store rate values in hw_value.
This frees up the hw_value for better future use.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Prepare the code for future changes so that new
code can refer to rate-related stuff without
forward declarations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch introduces tdls without tdls peer uapsd and tdls channel switching.
Transmitting tdls data frames works only for ethernet type frames, that's why
data addressed to tdls sta is in ethernet format.
This patch depends on commit c23e31cf7b ("mac80211: initialize rate control
earlier for tdls station").
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As a part of tdls implementation introduce
tdls related wmi data structures, constant
values and functions.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently station counting functions
(inc_num_stations/dec_num_stations) does not handle
tdls type of stations. Tdls station should be counted
because it consumes peer in firmware. Only not tdls
stations are excluded from this counting.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently number of tdls vdevs supported by firmware
is hardcoded. For future usage it is stored in ath10k
structure based on defined value.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are a few different tx paths depending on
firmware and frame itself.
Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.
Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.
Fixes: 8d6d362436 ("ath10k: fix offchan reliability")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 8348db2984 ("ath10k: add ATH10K_FW_IE_HTT_OP_VERSION") broke QCA6174
receive side as the HTT ids from ATH10K_FW_HTT_OP_VERSION_MAIN don't have
HTT_TLV_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND set. Fix this by adding a backwards
compatibility code which sets HTT op version if it's not set by the firmware
image.
Fixes: 8348db2984 ("ath10k: add ATH10K_FW_IE_HTT_OP_VERSION")
Reported-by: Michal Kazior <michal.kazior@tieto.com>
Tested-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Patch "ath10k: introduce basic tdls functionality" depends on this mac80211
patch:
c23e31cf7b mac80211: initialize rate control earlier for tdls station
Firmware 10.2.4.48-3 now supports management frames over HTT feature and has
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX. But as 10.2.4 branch has conflicting HTT ids
patch "ath10k: add ATH10K_FW_IE_HTT_OP_VERSION" is needed to fix the issue.
Older ath10k versions don't have support that support and to maintain backwards
compatibility we need bump up the FW API to 5 not break older versions.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Target to host HTT messages are conflicting between 10.x and other
firmware revisions. By maintaining separate HTT T2H tables for each
firmware revisions (main, 10x and tlv) similar to WMI abstraction,
solves the conflicts. Add ATH10K_FW_IE_HTT_OP_VERSION so that the firmware can
advertise the HTT interface to ath10k.
This fix is needed to get management frames over HTT (ie.
ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX disabled) working with 10.2.4.48-2 firmware.
Otherwise there will be unknown htt events and nothing works:
[30087.438343] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30087.448691] ath10k_pci 0000:02:00.0: htt event (19) not handled
[30149.032974] ath10k_pci 0000:02:00.0: htt event (19) not handled
If the firmware does not have ATH10K_FW_IE_HTT_OP_VERSION use the main HTT
interface. That way old firmware images will still work.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for WOW disconnect and magic-packet.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs
echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable channel 144 on 5GHz band since 802.11ac introduced it.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since thermal daemon is unaware of the device state, it might
try to adjust the throttle state when the device is powered down.
So the driver caches the value and will configure it while
powering up the target. The cached value will be programed later
once the device is brought up. In such case, returning error
status is confusing and misleading the user application. Hence
moving the driver state check before sending wmi command to target.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow driver to cache the throttle state when the devie is not
yet started. Configure the cached throttle state while powering
up the device. Since thermal daemon is unaware of the up/down cycle,
it assumes that device is throttled.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recently thermal mitigation is validated in station mode as well.
Hence allowing thermal throttling for all interfaces. This enables
user to validate thermal mitigation with different modes.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting the sysfs attribute ends up configuring the duty cycle,
but the interface through which the attribute is exposed
(cooling_device) is for setting the throttle/cooling state. This
is confusing the user. Hence renaming the cooling device interfaces
for better readability.
Cc: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
