Disable BH around the call to napi_schedule() to avoid following warning
[ 52.095499] NOHZ: local_softirq_pending 08
[ 52.421291] NOHZ: local_softirq_pending 08
[ 52.608313] NOHZ: local_softirq_pending 08
Fixes: 8d59de8f7b ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit b45f0674b9 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs"),
it changed EOPNOTSUPP to ENOTSUPP by mistake. This patch fixes it.
Fixes: b45f0674b9 ("mlx4: xdp: Allow raising MTU up to one page minus eth and vlan hdrs")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user prio field is wrong (and overflows) in the XDP forward
flow.
This is a result of a bad value for num_tx_rings_p_up, which should
account all XDP TX rings, as they operate for the same user prio.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent commit to get more precise rx/tx counters in ndo_get_stats64()
can lead to crashes at device dismantle, as Jesper found out.
We must prevent mlx4_en_fold_software_stats() trying to access
tx/rx rings if they are deleted.
Fix this by adding a test against priv->port_up in
mlx4_en_fold_software_stats()
Calling mlx4_en_fold_software_stats() from mlx4_en_stop_port()
allows us to eventually broadcast the latest/current counters to
rtnetlink monitors.
Fixes: 40931b8511 ("mlx4: give precise rx/tx bytes/packets counters")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-and-bisected-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@dev.mellanox.co.il>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 stats are chaotic because a deferred work queue is responsible
to update them every 250 ms.
Even sampling stats every one second with "sar -n DEV 1" gives
variations like the following :
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:39:22 eth0 146877.00 3265554.00 9467.15 4828168.50
07:39:23 eth0 146587.00 3260329.00 9448.15 4820445.98
07:39:24 eth0 146894.00 3259989.00 9468.55 4819943.26
07:39:25 eth0 110368.00 2454497.00 7113.95 3629012.17 <<>>
07:39:26 eth0 146563.00 3257502.00 9447.25 4816266.23
07:39:27 eth0 145678.00 3258292.00 9389.79 4817414.39
07:39:28 eth0 145268.00 3253171.00 9363.85 4809852.46
07:39:29 eth0 146439.00 3262185.00 9438.97 4823172.48
07:39:30 eth0 146758.00 3264175.00 9459.94 4826124.13
07:39:31 eth0 146843.00 3256903.00 9465.44 4815381.97
Average: eth0 142827.50 3179259.70 9206.30 4700578.16
This patch allows rx/tx bytes/packets counters being folded at the
time we need stats.
We now can fetch stats every 1 ms if we want to check NIC behavior
on a small time window. It is also easier to detect anomalies.
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:42:50 eth0 142915.00 3177696.00 9212.06 4698270.42
07:42:51 eth0 143741.00 3200232.00 9265.15 4731593.02
07:42:52 eth0 142781.00 3171600.00 9202.92 4689260.16
07:42:53 eth0 143835.00 3192932.00 9271.80 4720761.39
07:42:54 eth0 141922.00 3165174.00 9147.64 4679759.21
07:42:55 eth0 142993.00 3207038.00 9216.78 4741653.05
07:42:56 eth0 141394.06 3154335.64 9113.85 4663731.73
07:42:57 eth0 141850.00 3161202.00 9144.48 4673866.07
07:42:58 eth0 143439.00 3180736.00 9246.05 4702755.35
07:42:59 eth0 143501.00 3210992.00 9249.99 4747501.84
Average: eth0 142835.66 3182165.93 9206.98 4704874.08
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per RX ring packets/bytes counters are not protected by global
priv->stats_lock.
Better not confuse the reader, and use READ_ONCE() to show we read
these counters without surrounding synchronization.
Interrupt moderation is best effort, and we do not really care of
ultra precise counters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure mlx4_en_free_resources is called under the netdev state lock.
This is needed since RCU dereference of XDP prog should be protected.
Fixes: 326fe02d1e ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sagi Grimberg <sagi@grimberg.me>
CC: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 67f8b1dcb9 ("net/mlx4_en: Refactor the XDP forwarding rings
scheme") added a bug in that the prog's reference count is not dropped
in the error path when mlx4_en_try_alloc_resources() is failing from
mlx4_xdp_set().
We previously took bpf_prog_add(prog, priv->rx_ring_num - 1), that we
need to release again. Earlier in the call path, dev_change_xdp_fd()
itself holds a reference to the prog as well (hence the '- 1' in the
bpf_prog_add()), so a simple atomic_sub() is safe to use here. When
an error is propagated, then bpf_prog_put() is called eventually from
dev_change_xdp_fd()
Fixes: 67f8b1dcb9 ("net/mlx4_en: Refactor the XDP forwarding rings scheme")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9d2afba058.
The original issue would possibly exist if an external module
tried calling our "ethtool_ops" without checking if it still
exists.
The right way of solving it is by simply doing the check in
the caller side.
Currently, no action is required as there's no such use case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP statistics are reported in ethtool, in total and per ring,
as follows:
- xdp_drop: the number of packets dropped by xdp.
- xdp_tx: the number of packets forwarded by xdp.
- xdp_tx_full: the number of times an xdp forward failed
due to a full tx xdp ring.
In addition, all packets that are dropped/forwarded by XDP
are no longer accounted in rx_packets/rx_bytes of the ring,
so that they count traffic that is passed to the stack.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separately manage the two types of TX rings: regular ones, and XDP.
Upon an XDP set, do not borrow regular TX rings and convert them
into XDP ones, but allocate new ones, unless we hit the max number
of rings.
Which means that in systems with smaller #cores we will not consume
the current TX rings for XDP, while we are still in the num TX limit.
XDP TX rings counters are not shown in ethtool statistics.
Instead, XDP counters will be added to the respective RX rings
in a downstream patch.
This has no performance implications.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.
This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vf to VST 802.1ad mode (mlx4 VST QinQ mode) by setting vf vlan
protocol to 802.1ad.
VST 802.1ad mode in mlx4, is used for STAG strip/insertion by PF, while
the CTAG is set by the VF.
Read current vlan protocol as part of the vf configuration state.
Upon setting vf vlan protocol to 802.1ad, we use a mechanism of handshake
to verify that both the vf and the pf driver version support it.
The handshake uses the command QUERY_FUNC_CAP:
- The vf sets a pre-defined support bit in input modifier.
- A pf that supports the feature sends the request to the vf through a
pre-defined field in the output mailbox.
- In case vf does not support the feature, the pf will fail the control
command (in this case, IP link tool command to set the vf vlan
protocol to 802.1ad).
No change in VST 802.1Q mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Ethernet VF, disable vlan HW acceleration on VF
while it is set to VF vlan protocol 802.1ad mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a capability check before enabling DCBX.
In addition, it re-organizes the relevant data structures,
and fixes a typo in a define.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the preempt mode, the bpf_prog stored in xdp_prog may be
freed despite the use of call_rcu inside bpf_prog_put. The situation is
possible when running in PREEMPT_RCU=y mode, for instance, since the rcu
callback for destroying the bpf prog can run even during the bh handling
in the mlx4 rx path.
Several options were considered before this patch was settled on:
Add a napi_synchronize loop in mlx4_xdp_set, which would occur after all
of the rings are updated with the new program.
This approach has the disadvantage that as the number of rings
increases, the speed of update will slow down significantly due to
napi_synchronize's msleep(1).
Add a new rcu_head in bpf_prog_aux, to be used by a new bpf_prog_put_bh.
The action of the bpf_prog_put_bh would be to then call bpf_prog_put
later. Those drivers that consume a bpf prog in a bh context (like mlx4)
would then use the bpf_prog_put_bh instead when the ring is up. This has
the problem of complexity, in maintaining proper refcnts and rcu lists,
and would likely be harder to review. In addition, this approach to
freeing must be exclusive with other frees of the bpf prog, for instance
a _bh prog must not be referenced from a prog array that is consumed by
a non-_bh prog.
The placement of rcu_read_lock in this patch is functionally the same as
putting an rcu_read_lock in napi_poll. Actually doing so could be a
potentially controversial change, but would bring the implementation in
line with sk_busy_loop (though of course the nature of those two paths
is substantially different), and would also avoid future copy/paste
problems with future supporters of XDP. Still, this patch does not take
that opinionated option.
Testing was done with kernels in either PREEMPT_RCU=y or
CONFIG_PREEMPT_VOLUNTARY=y+PREEMPT_RCU=n modes, with neither exhibiting
any drawback. With PREEMPT_RCU=n, the extra call to rcu_read_lock did
not show up in the perf report whatsoever, and with PREEMPT_RCU=y the
overhead of rcu_read_lock (according to perf) was the same before/after.
In the rx path, rcu_read_lock is eventually called for every packet
from netif_receive_skb_internal, so the napi poll call's rcu_read_lock
is easily amortized.
v2:
Remove extra rcu_read_lock in mlx4_en_process_rx_cq body
Annotate xdp_prog with __rcu, and convert all usages to rcu_assign or
rcu_dereference[_protected] as appropriate.
Add explicit mutex lock around rcu_assign instead of xchg loop.
Fixes: d576acf0a2 ("net/mlx4_en: add page recycle to prepare rx ring for tx support")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user will now be able to loop packets back out of the same port using
a bpf program attached to xdp hook. Updates to the packet contents from
the bpf program is also supported.
For the packet write feature to work, the rx buffers are now mapped as
bidirectional when the page is allocated. This occurs only when the xdp
hook is active.
When the program returns a TX action, enqueue the packet directly to a
dedicated tx ring, so as to avoid completely any locking. This requires
the tx ring to be allocated 1:1 for each rx ring, as well as the tx
completion running in the same softirq.
Upon tx completion, this dedicated tx ring recycles pages without
unmapping directly back to the original rx ring. In steady state tx/drop
workload, effectively 0 page allocs/frees will occur.
In order to separate out the paths between free and recycle, a
free_tx_desc func pointer is introduced that is optionally updated
whenever recycle_ring is activated. By default the original free
function is always initialized.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4 driver by default allocates order-3 pages for the ring to
consume in multiple fragments. When the device has an xdp program, this
behavior will prevent tx actions since the page must be re-mapped in
TODEVICE mode, which cannot be done if the page is still shared.
Start by making the allocator configurable based on whether xdp is
running, such that order-0 pages are always used and never shared.
Since this will stress the page allocator, add a simple page cache to
each rx ring. Pages in the cache are left dma-mapped, and in drop-only
stress tests the page allocator is eliminated from the perf report.
Note that setting an xdp program will now require the rings to be
reconfigured.
Before:
26.91% ksoftirqd/0 [mlx4_en] [k] mlx4_en_process_rx_cq
17.88% ksoftirqd/0 [mlx4_en] [k] mlx4_en_alloc_frags
6.00% ksoftirqd/0 [mlx4_en] [k] mlx4_en_free_frag
4.49% ksoftirqd/0 [kernel.vmlinux] [k] get_page_from_freelist
3.21% swapper [kernel.vmlinux] [k] intel_idle
2.73% ksoftirqd/0 [kernel.vmlinux] [k] bpf_map_lookup_elem
2.57% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
After:
31.72% swapper [kernel.vmlinux] [k] intel_idle
8.79% swapper [mlx4_en] [k] mlx4_en_process_rx_cq
7.54% swapper [kernel.vmlinux] [k] poll_idle
6.36% swapper [mlx4_core] [k] mlx4_eq_int
4.21% swapper [kernel.vmlinux] [k] tasklet_action
4.03% swapper [kernel.vmlinux] [k] cpuidle_enter_state
3.43% swapper [mlx4_en] [k] mlx4_en_prepare_rx_desc
2.18% swapper [kernel.vmlinux] [k] native_irq_return_iret
1.37% swapper [kernel.vmlinux] [k] menu_select
1.09% swapper [kernel.vmlinux] [k] bpf_map_lookup_elem
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the BPF_PROG_TYPE_XDP hook in mlx4 driver.
In tc/socket bpf programs, helpers linearize skb fragments as needed
when the program touches the packet data. However, in the pursuit of
speed, XDP programs will not be allowed to use these slower functions,
especially if it involves allocating an skb.
Therefore, disallow MTU settings that would produce a multi-fragment
packet that XDP programs would fail to access. Future enhancements could
be done to increase the allowable MTU.
The xdp program is present as a per-ring data structure, but as of yet
it is not possible to set at that granularity through any ndo.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the lost of Ethernet port on low memory system,
when driver frees its resources and fails to allocate new resources.
Issue could happen while changing number of channels, rings size or
changing the timestamp configuration.
This fix is necessary because of removing vmap use in the code.
When vmap was in use driver could allocate non-contiguous memory
and make it contiguous with vmap. Now it could fail to allocate
a large chunk of contiguous memory and lose the port.
Current code tries to allocate new resources and then upon success
frees the old resources.
Fixes: 73898db043 ('net/mlx4: Avoid wrong virtual mappings')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filters cleanup should be done once before destroying net device,
since filters list is contained in the private data.
Fixes: 1eb8c695bd ('net/mlx4_en: Add accelerated RFS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify mlx4_en_vlan_rx_[add/kill]_vid to return error value in case of
failure.
Fixes: 8e586137e6 ('net: make vlan ndo_vlan_rx_[add/kill]_vid return error value')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type is VXLAN we can maintain the same
functionality.
In addition I updated the socket address family check so that instead of
excluding IPv6 we instead abort of type is not IPv4. This makes much more
sense as we should only be supporting IPv4 outer addresses on this
hardware.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4e driver does not support more than one port for VXLAN offload. As
such expecting the hardware to offload other ports is invalid since it
appears the parsing logic is used to perform Tx checksum and segmentation
offloads. Use the vxlan_port number to determine in which cases we can
apply the offload and in which cases we can not.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am not sure mlx4_en_netpoll() is doing anything useful right now.
mlx4 has different NAPI structures for RX and TX, and netpoll only wants
to drain TX queues.
Lets schedule NAPI polls on TX, not RX.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simply can use the standard net_device stats.
We do not need to clear fields that are already 0.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 uses a private struct net_device_stats in a vain attempt
to avoid races.
This is buggy because multiple cpus could call mlx4_en_get_stats()
at the same time, so ret_stats can not guarantee stable results.
To fix this, we need to switch to ndo_get_stats64() as this
method provides per-thread storage.
This allows to reduce mlx4_en_priv bloat.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_clear_stats() clears about everything but few TX ring
fields are missing :
- queue_stopped, wake_queue, tso_packets, xmit_more
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) mlx4_en_xmit() can increment priv->stats.tx_dropped, but this variable
is overwritten in mlx4_en_DUMP_ETH_STATS().
2) This increment was not SMP safe, as a port might have many TX queues.
Add a per TX ring tx_dropped to fix these issues.
This is u32 as mlx4_en_DUMP_ETH_STATS() will add a 32bit field.
So lets avoid bugs with SNMP agents having to cope with partial
overwraps. (One of these agents being bond_fold_stats())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory. On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent. Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent(). Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).
The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.
Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reported-by: David Daney <david.daney@cavium.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From what I can tell the ConnectX-3 will support an inner IPv6 checksum and
segmentation offload, however it cannot support outer IPv6 headers. This
assumption is based on the fact that I could see the checksum being
offloaded for inner header on IPv4 tunnels, but not on IPv6 tunnels.
For this reason I am adding the feature to the hw_enc_features and adding
an extra check to the features_check call that will disable GSO and
checksum offload in the case that the encapsulated frame has an outer IP
version of that is not 4. The check in mlx4_en_features_check could be
removed if at some point in the future a fix is found that allows the
hardware to offload segmentation/checksum on tunnels with an outer IPv6
header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the mlx4 hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
