There is a a bug in defered ack stuff that causes a race with the
destroy of a QP.
A packet causes a defered ack to be pended by putting the QP
into an rcd queue.
A return from the driver interrupt processing will process that rcd
queue of QPs and attempt to do a direct send of the ack. At this
point no locks are held and the above QP could now be put in the reset
state in the qp destroy logic. A refcount protects the QP while it
is in the rcd queue so it isn't going anywhere yet.
If the direct send fails to allocate a pio buffer,
hfi1_schedule_send() is called to trigger sending an ack from the
send engine. There is no state test in that code path.
The refcount is then dropped from the driver.c caller
potentially allowing the qp destroy to continue from its
refcount wait in parallel with the workqueue scheduling of the qp.
Cc: stable@vger.kernel.org
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Prevent over-reading the SGE length by using byte
reads for non quad-word reads.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In certain cases, if the tail of an SGE is not
8-byte aligned, bytes beyond the end to an 8-byte
alignment can be read. Change the copy routine
to avoid the over-read. Instead, stop on the final
whole quad-word, then read the remaining bytes.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow a longer timeout for i2c due to clock stretching and
inaccurate jiffy timing when under a spin lock. This timeout
is consistent with other i2c-algo-bit users.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ib_write_bw test allows using up to 16384 QPs. When a relatively
large number of QPs (within that range) is used, the test can fail
because the number of CQ entries needed exceeds the limit set by the
driver.
This patch increases the default setting of max_cqes from 0x2FFFF
(196607) to 0x2FFFFF(3145727), which is sufficient to cover the
maximum number needed by the ib_write_bw test (2097152). The default
setting of max_qps is also increased from 16384 to 32768 to allow
the test to run successfully with 16383 or 16384 QPs.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FM should have full control to set the pkeys in the
driver pkey table. Remove filtering done by the driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no need to have a global qpt_mask as that does not support the
multiple chip model which qib has. Instead rely on the value which
exists already in the device data (dd).
Fixes: 898fa52b4a "IB/qib: Remove qpn, qp tables and related variables from qib"
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This allows for adding additional pages of adaptive pio
opcode control including manufacturer specific ones.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds lockdep asserts in key code paths for
insuring lock correctness.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The call is misplaced in the reset calldown function
and causes issues with lockdep assertions that are to
be added.
Fixes: Commit a2c2d60895 ("staging/rdma/hfi1: Remove create_qp functionality")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Existing locking scheme in affinity.c file using the
&node_affinity.lock spinlock is not very elegant.
We acquire the lock to get hfi1_affinity_node entry,
unlock, and then use the entry without the lock held.
With more functions being added, which access and
modify the entries, this can lead to race conditions.
This patch makes this locking scheme more consistent.
It changes the spinlock to mutex. Since all the code
is executed in a user process context there is no need
for a spinlock. This also allows to keep the lock
not only while we look up for the node affinity entry,
but over the whole section where the entry is being used.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The dma_XXX API functions return bus addresses which are
physical addresses when IOMMU is disabled. Buffer
mapping to user-space is done via remap_pfn_range() with PFN
based on bus address instead of physical. This results in
wrong pages being mapped to user-space when IOMMU is enabled.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tymoteusz Kielan <tymoteusz.kielan@intel.com>
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Each user SDMA request coming into the driver may contain multiple packets.
Each user packet may use multiple SDMA descriptors to fill the send buffer.
The field seqsubmitted in struct user_sdma_request counts the number of
user packets submitted to an SDMA engine. Sometimes, the intermediate count
may not be updated properly. However, once all the packets' descriptors
are successfully submitted to the SDMA engine, the final count is updated
correctly. But, if only some of the packets are submitted to the engine due
to an error, the intermediate count doesn't reflect the partial number of
packets submitted to the SDMA engine. This can cause a hang later in the
code as the count of packets submitted to the SDMA engine doesn't match the
the count of packets processed by the SDMA engine.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All calls to tune_serdes and start_link are paired. Move
tune_serdes inside start_link.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use common header file structs, defines, and accessors
in the drivers. The old declarations are removed.
The repositioning of the includes allows for the removal
of hfi1_message_header and replaces its use with ib_header.
Also corrected are two issues with set_armed_to_active():
- The "packet" parameter is now a pointer as it should have been
- The etype is validated to insure that the header is correct
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.
CURRENT_TIME is also not y2038 safe.
This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.
Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Instead of exposing ib_get_dma_mr to ULPs and letting them use it more or
less unchecked, this moves the capability of creating a global rkey into
the RDMA core, where it can be easily audited. It also prints a warning
everytime this feature is used as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allocate resources dynamically to cxgb4's Upper layer driver's(ULD) like
cxgbit, iw_cxgb4 and cxgb4i. Allocate resources when they register with
cxgb4 driver and free them while unregistering. All the queues and the
interrupts for them will be allocated during ULD probe only and freed
during remove.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Various fixes to rdmavt, ipoib, mlx5, mlx4, rxe
-----BEGIN PGP SIGNATURE-----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=HC3X
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Round three of 4.8 rc fixes.
This is likely the last rdma pull request this cycle. The new rxe
driver had a few issues (you probably saw the boot bot bug report) and
they should be addressed now. There are a couple other fixes here,
mainly mlx4. There are still two outstanding issues that need
resolved but I don't think their fix will make this kernel cycle.
Summary:
- Various fixes to rdmavt, ipoib, mlx5, mlx4, rxe"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/rdmavt: Don't vfree a kzalloc'ed memory region
IB/rxe: Fix kmem_cache leak
IB/rxe: Fix race condition between requester and completer
IB/rxe: Fix duplicate atomic request handling
IB/rxe: Fix kernel panic in udp_setup_tunnel
IB/mlx5: Set source mac address in FTE
IB/mlx5: Enable MAD_IFC commands for IB ports only
IB/mlx4: Diagnostic HW counters are not supported in slave mode
IB/mlx4: Use correct subnet-prefix in QP1 mads under SR-IOV
IB/mlx4: Fix code indentation in QP1 MAD flow
IB/mlx4: Fix incorrect MC join state bit-masking on SR-IOV
IB/ipoib: Don't allow MC joins during light MC flush
IB/rxe: fix GFP_KERNEL in spinlock context
This improves readability and hides the reference count
mechanism from the client drivers.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef875 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify the mlx4_ib_diag_counters() to avoid the following error in the
hypervisor when the slave tries to query the hardware counters in SR-IOV
mode.
mlx4_core 0000:81:00.0: Unknown command:0x30 accepted from slave:1
Fixes: 3f85f2aaab ("IB/mlx4: Add diagnostic hardware counters")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.
This fix separates scope bits and join states bits a nibble each.
Fixes: b9c5d6a643 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add cxgb_mk_rx_data_ack() to remove duplicate
code to form CPL_RX_DATA_ACK hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_rpl() to remove duplicate
code to form CPL_ABORT_RPL hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_abort_req() to remove duplicate code
to form CPL_ABORT_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_close_con_req() to remove duplicate
code to form CPL_CLOSE_CON_REQ hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_mk_tid_release() to remove duplicate code
to form CPL_TID_RELEASE hardware command.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_compute_wscale() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_best_mtu() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_is_neg_adv() in libcxgb_cm.h to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route6() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_find_route() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cxgb_get_4tuple() in libcxgb_cm.c to remove
it's duplicate definitions from cxgb4/cm.c and
cxgbit/cxgbit_cm.c.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A set of fixes for the current series in the realm of block.
Like the previous pull request, the meat of it are fixes for the nvme
fabrics/target code. Outside of that, just one fix from Gabriel for
not doing a queue suspend if we didn't get the admin queue setup in
the first place"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme-rdma: add back dependency on CONFIG_BLOCK
nvme-rdma: fix null pointer dereference on req->mr
nvme-rdma: use ib_client API to detect device removal
nvme-rdma: add DELETING queue flag
nvme/quirk: Add a delay before checking device ready for memblaze device
nvme: Don't suspend admin queue that wasn't created
nvme-rdma: destroy nvme queue rdma resources on connect failure
nvme_rdma: keep a ref on the ctrl during delete/flush
iw_cxgb4: block module unload until all ep resources are released
iw_cxgb4: call dev_put() on l2t allocation failure
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise an endpoint can be still closing down causing a touch
after free crash. Also WARN_ON if ulps have failed to destroy
various resources during device removal.
Fixes: ad61a4c7a9 ("iw_cxgb4: don't block in destroy_qp awaiting the last deref")
Reviewed-by: Sagi Grimberg <sagi@grimbrg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
The debugfs RCU trips many debug kernel warnings because of potential
sleeps with an RCU read lock held. This includes both user copy calls
and slab allocations throughout the file.
This patch switches the RCU to use SRCU for file remove/access
race protection.
In one case, the SRCU is implicit in the use of the raw debugfs file
object and just works.
In the seq_file case, a wrapper around seq_read() and seq_lseek() is
used to enforce the SRCU using the debugfs supplied functions
debugfs_use_file_start() and debugfs_use_file_stop().
The sychronize_rcu() is deleted since the SRCU prevents the remove
access race.
The RCU locking is kept for qp_stats since the QP hash list is
protected using the non-sleepable RCU.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The global variable n_krcvqs stores the sum of the number of kernel
receive queues of VLs 0-7 which the user can pass to the driver through
the module parameter array krcvqs which is of type unsigned integer. If
the user passes large value(s) into krcvqs parameter array, it can cause
an arithmetic overflow while calculating n_krcvqs which is also of type
unsigned int. The overflow results in an incorrect value of n_krcvqs
which can lead to kernel crash while loading the driver.
Fix by changing the data type of n_krcvqs to unsigned long. This patch
also changes the data type of other variables that get their values from
n_krcvqs.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sometimes a QSFP device does not respond in the expected time
after a power-on. Add a read pre-check/retry when starting
the link on driver load.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the set_txreq_header_ahg(), The KDETH Intr bit is obtained from the
header in the user sdma request using a KDETH_GET shift and mask macro.
This value is then futher right shifted by 16 causing us to lose the
value i.e it is shifted to zero, leading to the following
smatch warning:
drivers/infiniband/hw/hfi1/user_sdma.c:1482 set_txreq_header_ahg()
warn: mask and shift to zero
The Intr bit should be left shifted into its correct position in the
KDETH header before the AHG update.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When trying to align the source pointer and there's a byte carry
in an SGE copy, bytes are borrowed from the next quad-word X to
complete the required quad-word copy. Then, the SGE length is
reduced by the number of borrowed bytes. After this, if the
remaining number of bytes from quad-word X (extra bytes) is
greater than the new SGE length, the number of extra bytes needs
to be updated to the new SGE length. Otherwise, when the
SGE length gets updated again after the extra bytes are read to
create the new byte carry, it goes negative, which then becomes
a very large number as the SGE length is an unsigned integer.
This causes SGE buffer to be over-read.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove returning errors from mlx5 poll_cq function. Polling CQ
operation in kernel never fails by Mellanox HCA architecture and
respective driver design.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use TIR number based on selector, it should be done to differentiate
between RSS QP to RAW one.
Reported-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return variable was set in a line before the
actual return was called in begin_wqe function.
This patch removes such variable and simplifies the code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The returned value should be EINVAL, because it is caused by wrong
caller and not by internal overflow event.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove returning errors from mlx4 poll_cq function. Polling CQ
operation in kernel never fails by Mellanox HCA architecture and
respective driver design.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
By Mellanox HW design and SW implementation, poll_cq never
fails and returns errors, so all these printks are to catch ULP bugs.
In case of such bug, the reverted patch will cause reentry of the
function, resulting in a printk storm.
This reverts commit 5412352fcd ("IB/mlx4: Return EAGAIN for any error in mlx4_ib_poll_one")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We get 1 warning when build kernel with W=1:
drivers/infiniband/hw/cxgb4/qp.c:686:6: warning: no previous prototype for '_free_qp' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(u64)' which is 8.
It is likely that the number of bits of 'port_mask' was expected here.
Use sizeof() * 8 to get the correct number.
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(tmp)' which is likely to be 4 or 8
because 'tmp' is an 'unsigned long'.
It is likely that the number of bits of 'tmp' was expected here. So use
BITS_PER_LONG instead.
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Majd Dibbiny <majd@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In all other places in this file where 'find_first_bit' is called,
port_num is defined as a 'u8' and no casting is done.
Do the same here in order to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Device notifications are not received after the first interface is
closed; since there is an unregister for notifications on every
interface close. Correct this by unregistering for device
notifications only when the last interface is closed. Also, make
all operations on the i40iw_notifiers_registered atomic as it
can be read/modified concurrently.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update iwqp->hw_iwarp_state to reflect the new state of the CQP
modify QP operation. This avoids reissuing a CQP operation to
modify a QP to a state that it is already in.
Fixes: 4e9042e647 ("i40iw: add hw and utils files")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Send a zero length last streaming mode message for loopback
connections to synchronize between accepting QP and connecting QP.
This avoids data transfer to start on the accepting QP before
the connecting QP is in RTS. Also remove function i40iw_loopback_nop()
as it is no longer used.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is meant to add support of ACPI to the Hisilicon RoCE
driver.
Changes done are primarily meant to detect the type and then either
use DT specific or ACPI spcific functions. Where ever possible,
this patch tries to make use of Unified Device Property Interface
APIs to support both DT and ACPI through single interface.
This patch depends upon HNS ethernet driver to Reset RoCE. This
function within HNS ethernet driver has also been enhanced to
support ACPI and is part of other accompanying patch with this
patch-set.
NOTE: The changes in this patch are done over below branch,
https://github.com/dledford/linux/tree/hns-roce
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current driver is reporting wrong values for max_sge and
max_sge_rd in query_device. This breaks the nfs rdma and iser
in some device profiles. Fixing the driver to report
correct values from FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwpbl->iwmr points to the structure that contains iwpbl,
which is iwmr. Setting this to NULL would result in
writing to freed memory. So just free iwmr, and return.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Memory allocated for iwqp; iwqp->allocated_buffer is freed twice in
the create_qp error path. Correct this by having it freed only once in
i40iw_free_qp_resources().
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This file does not use any structs or functions defined by io-mapping.h
(nor does it directly use iomap, ioremap, iounamp or friends). Remove it
to simplify verification of changes to io-mapping.h
The include existed since its inception in
commit e126ba97db
Author: Eli Cohen <eli@mellanox.com>
Date: Sun Jul 7 17:25:49 2013 +0300
mlx5: Add driver for Mellanox Connect-IB adapters
which looks like a copy across from the Mellanox ethernet driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eli Cohen <eli@mellanox.com>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_free_virt_mem(), do not set mem->va to NULL
after freeing it as mem->va is a self-referencing pointer
to mem.
Fixes: 4e9042e647 ("i40iw: add hw and utils files")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add NULL check for pdata and pdata->addr before the memcpy in
i40iw_form_cm_frame(). This fixes a NULL pointer de-reference
which occurs when the MPA private data pointer is NULL. Also
only copy pdata->size bytes in the memcpy to prevent reading
past the length of the private data buffer provided by upper layer.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current cxgb4 arm CQ logic ignores IB_CQ_REPORT_MISSED_EVENTS for
request completion notification on a CQ. Due to this ib_poll_handler()
assumes all events polled and avoids further iopoll scheduling.
This patch adds logic to cxgb4 ib_req_notify_cq() handler to check if
CQ is not empty and return accordingly. Based on the return value of
ib_req_notify_cq() handler, ib_poll_handler() will schedule a run of
iopoll handler.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_open(), check if interface is already open
and return success if it is.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_alloc_resource(), ensure that the update to
req_resource_num is protected by the lock.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwdev->mem_resources is incorrectly defined as an unsigned
long instead of u8. As a result, the offset into the dynamic
allocated structures in i40iw_initialize_hw_resources() is
incorrectly calculated and would lead to writing of memory
regions outside of the allocated buffer.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw initiator sends an MPA-request with ird=16 and ord=16. The cxgb4
responder sends an MPA-reply with ord = 32 causing i40iw to terminate
due to insufficient resources.
The logic to reduce the ORD to <= peer's IRD was wrong.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw initiator sends an MPA-request with ird = 63, ord = 63. The
cxgb4 responder sends a RST. Since the inbound ord=63 and it exceeds
the max_ird/c4iw_max_read_depth (=32 default), chelsio decides to abort.
Instead, cxgb4 should adjust the ord/ird down before presenting it to
the ULP.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously, J_KEY generation was based on the lower 16 bits
of the user's UID. While this works, it was not good enough
as a non-root user could collide with a root user given a
sufficiently large UID.
This patch attempt to improve the J_KEY generation by using
the following algorithm:
The 16 bit J_KEY space is partitioned into 3 separate spaces
reserved for different user classes:
* all users with administtor privileges (including 'root')
will use J_KEYs in the range of 0 to 31,
* all kernel protocols, which use KDETH packets will use
J_KEYs in the range of 32 to 63, and
* all other users will use J_KEYs in the range of 64 to
65535.
The above separation is aimed at preventing different user levels
from sending packets to each other and, additionally, separate
kernel protocols from all other types of users. The later is meant
to prevent the potential corruption of kernel memory by any other
type of user.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver does not check if the CableInfo query is supported for the
port type. Return early if CableInfo is not supported for the port type,
making compliance with the specification explicit and preventing lower
level code from potentially doing the wrong thing if the query is not
supported for the hardware implementation.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If 'pci_register_driver' fails, we return 'err' which is known to be 0.
Return the error instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is likely that checking the result of 'setup_ctxt' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Validate the etype to insure that the header is correct.
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The "packet" parameter was being passed on the stack,
change it to a pointer.
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The monitor values from bytes 22 through 81 of the QSFP memory space
(SFF 8636) are dynamic and serving them out of the QSFP memory cache
maintained by the driver provides stale data to the CableInfo SMA query.
This patch refreshes the dynamic values from the QSFP memory on request
and overwrites the stale data from the cache for the overlap between the
requested range and the monitor range.
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The qp init function does a kzalloc() while holding the RCU
lock that encounters the following warning with a debug kernel
when a cat of the qp_stats is done:
[ 231.723948] rcu_scheduler_active = 1, debug_locks = 0
[ 231.731939] 3 locks held by cat/11355:
[ 231.736492] #0: (debugfs_srcu){......}, at: [<ffffffff813001a5>] debugfs_use_file_start+0x5/0x90
[ 231.746955] #1: (&p->lock){+.+.+.}, at: [<ffffffff81289a6c>] seq_read+0x4c/0x3c0
[ 231.755873] #2: (rcu_read_lock){......}, at: [<ffffffffa0a0c535>] _qp_stats_seq_start+0x5/0xd0 [hfi1]
[ 231.766862]
The init functions do an implicit next which requires the rcu read lock
before the kzalloc().
Fix for both drivers is to change the scope of the init function to only
do the allocation and the initialization of the just allocated iter.
The implict next is moved back into the respective start functions to fix
the issue.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
CC: <stable@vger.kernel.org> # 4.6.x-
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If CONFIG_FRAME_WARN is small (1K) and CONFIG_NR_CPUS big
then a frame size warning is triggered during build.
Allocate the cpu mask dynamically to silence the warning.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Error code EAGAIN should be used when errors are temporary and next call
might succeeds.
When error code other than EAGAIN is returned, the caller (mlx4_ib_poll)
will assume all CQE in the same bunch are error too and will drop them all.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to return int if function always returns 0
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch added Kconfig and Makefile for building RoCE module.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These are the various new source code files for the Hisilicon
RoCE driver for ARM architecture.
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Replaced mlx5_query_port_proto_oper with separate functions per link
type. The functions should take different arguments so no point in
trying to unite them.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Now as all commands use mlx5 ifc interface, instead of doing two calls
for executing a command we embed command status checking into
mlx5_cmd_exec to simplify the interface.
Also we do here some cleanup for redundant software structures
(inbox/outbox) and functions and improved command failure output.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Prior to this patch we assumed that modify QP commands have the
same layout.
In ConnectX-4 for each QP transition there is a specific command
and their layout can vary.
e.g: 2err/2rst commands don't have QP context in their layout and before
this patch we posted the QP context in those commands.
Fortunately the FW only checks the suffix of the commands and executes
them, while ignoring all invalid data sent after the valid command
layout.
This patch removes mlx5_modify_qp_mbox_in and changes
mlx5_core_qp_modify to receive the required transition and QP context
with opt_param_mask if needed. This way the caller is not required to
provide the command inbox layout and it will be generated automatically.
mlx5_core_qp_modify will generate the command inbox/outbox layouts
according to the requested transition and will fill the requested
parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created QP/XRCD commands layout
amd use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created MKey/PSV commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created CQ commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
- hfi1 driver updates
- Fix for max SGEs allowed via RDMA R/W API
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cQcp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull second round of rdma updates from Doug Ledford:
"This can be split out into just two categories:
- fixes to the RDMA R/W API in regards to SG list length limits
(about 5 patches)
- fixes/features for the Intel hfi1 driver (everything else)
The hfi1 driver is still being brought to full feature support by
Intel, and they have a lot of people working on it, so that amounts to
almost the entirety of this pull request"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (84 commits)
IB/hfi1: Add cache evict LRU list
IB/hfi1: Fix memory leak during unexpected shutdown
IB/hfi1: Remove unneeded mm argument in remove function
IB/hfi1: Consistently call ops->remove outside spinlock
IB/hfi1: Use evict mmu rb operation
IB/hfi1: Add evict operation to the mmu rb handler
IB/hfi1: Fix TID caching actions
IB/hfi1: Make the cache handler own its rb tree root
IB/hfi1: Make use of mm consistent
IB/hfi1: Fix user SDMA racy user request claim
IB/hfi1: Fix error condition that needs to clean up
IB/hfi1: Release node on insert failure
IB/hfi1: Validate SDMA user iovector count
IB/hfi1: Validate SDMA user request index
IB/hfi1: Use the same capability state for all shared contexts
IB/hfi1: Prevent null pointer dereference
IB/hfi1: Rename TID mmu_rb_* functions
IB/hfi1: Remove unneeded empty check in hfi1_mmu_rb_unregister()
IB/hfi1: Restructure hfi1_file_open
IB/hfi1: Make iovec loop index easy to understand
...
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oZOO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
The kfree() function was called in a few cases by the mthca_reset()
function during error handling even if the passed variables "bridge_header"
and "hca_header" contained a null pointer.
Adjust jump targets according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The pci_dev_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The sc_return_credits() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose IB diagnostic hardware counters.
The counters count IB events and are applicable for IB and RoCE.
The counters can be divided into two groups, per device and per port.
Device counters are always exposed.
Port counters are exposed only if the firmware supports per port counters.
rq_num_dup and sq_num_to are only exposed if we have firmware support
for them, if we do, we expose them per device and per port.
rq_num_udsdprd and num_cqovf are device only counters.
rq - denotes responder.
sq - denotes requester.
|-----------------------|---------------------------------------|
| Name | Description |
|-----------------------|---------------------------------------|
|rq_num_lle | Number of local length errors |
|-----------------------|---------------------------------------|
|sq_num_lle | number of local length errors |
|-----------------------|---------------------------------------|
|rq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|sq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|rq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|sq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|rq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_mwbe | Number of Memory Window bind errors |
|-----------------------|---------------------------------------|
|sq_num_bre | Number of bad response errors |
|-----------------------|---------------------------------------|
|sq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|rq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|sq_num_roe | Number of remote operation errors |
|-----------------------|---------------------------------------|
|sq_num_tree | Number of transport retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rree | Number of RNR NAK retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rnr | Number of RNR NAKs sent |
|-----------------------|---------------------------------------|
|sq_num_rnr | Number of RNR NAKs received |
|-----------------------|---------------------------------------|
|rq_num_oos | Number of Out of Sequence requests |
| | received |
|-----------------------|---------------------------------------|
|sq_num_oos | Number of Out of Sequence NAKs |
| | received |
|-----------------------|---------------------------------------|
|rq_num_udsdprd | Number of UD packets silently |
| | discarded on the Receive Queue due to |
| | lack of receive descriptor |
|-----------------------|---------------------------------------|
|rq_num_dup | Number of duplicate requests received |
|-----------------------|---------------------------------------|
|sq_num_to | Number of time out received |
|-----------------------|---------------------------------------|
|num_cqovf | Number of CQ overflows |
|-----------------------|---------------------------------------|
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We allocate a small tracking structure as part of mlx4_ib_resize_cq().
However, we don't need to use GFP_ATOMIC -- immediately after the
allocation, we call mlx4_cq_resize(), which allocates a command
mailbox with GFP_KERNEL and then sleeps on a firmware command, so we
better not be in an atomic context.
This actually has a real impact, because when this GFP_ATOMIC
allocation fails (and GFP_ATOMIC does fail in practice) then a
userspace consumer resizing a CQ will get a spurious failure that we
can easily avoid.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a strict policy in the Linux kernel that new drivers must be
disabled by default. Hence leave out the "default m" line from Kconfig.
Fixes: f48ad614c1 ("IB/hfi1: Move driver out of staging")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Jubin John <jubin.john@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The original code used a LRU list to evict nodes which were least
recently used. For correctness the evict code was moved under the
handler->lock, now add back the LRU list.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
During an unexpected shutdown, references to tid_rb_node were NULL'ed out
without properly being released.
Fix this by calling clear_tid_node in the mmu notifier remove callback
rather than after these callbacks are called.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The reworked mmu_rb interface allows the unused mm argument to be removed.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ops->remove() callback was called by hfi1_mmu_unregister() with a
NULL mm argument while holding a spinlock. In the case of sdma_rb_remove()
this caused it to pass current->mm to hfi1_release_user_pages()
This had 2 problems. First this would attempt to acquire the mmap_sem
under a spin lock. Second the use of current->mm is not always guaranteed
to be the proper mm when the fd is being closed.
Rather than depend on this implicit behavior we move all calls to
ops->remove outside of the spinlock. This also allows the correct
mm to be used in the remove callback without fear of deadlock.
Because the MMU notifier is not guaranteed to hold mm->mmap_sem, but
usually does, we must delay all remove callbacks until out of the notifier,
when the callbacks can take the mmap_sem if they need to.
Code comments were added to clarify what the expectations are for the
users of the mmu rb tree.
Suggested-by: Jim Foraker <foraker1@llnl.gov>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use the new cache evict operation in the SDMA code. This allows the cache
to properly coordinate evicts and removes, preventing any race. With this
change, the separate list, lock, and race flag are not needed.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow users to clear nodes from the rb tree based on their evict callback.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Per file descriptor TID caching actions depend on a global that can
change midway through the lifetime of that file descriptor.
Make the use of caching consistent for the life of the file descriptor
by using the presence of the cache handler to decide when to use the cache
functions.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The objects which use cache handling should reference their own handler
object not the internal data structure it uses to track the nodes.
Have the "users" of the mmu notifier code pass opaque objects which can
then be properly used in the mmu callbacks depending on the owners needs.
This patch has the additional benefit that operations no longer require a
look up in a list to find the handlers.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The hfi1 driver registers a mmu_notifier callback when /dev/hfi1_* is
opened, and unregisters it when the device is closed. The driver
incorrectly assumes that the close will always happen from the same
context as the open. In particular, closes due to SIGKILL or OOM killer
activity may happen from a different context. In these cases, the wrong
mm is passed to mmu_notifier_unregister(), which causes improper reference
counting for the victim mm, and eventual memory corruption.
Preserve the mm for all open file descriptors and use this mm rather than
current->mm for memory operations for the lifetime of that fd. Note: this
patch leaves 1 use of current->mm in place. This use is removed in a
follow on patch because other functional changes were required prior to
that use being removed.
If registration fails, there is no reason to keep the handler object
around. Free the handler object rather than add it to the list to
prevent any mmu_notifier operations, including unregister, when
registration fails.
Suggested-by: Jim Foraker <foraker1@llnl.gov>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The user SDMA in-use claim bit is in the structure that gets zeroed out
once the claim is made. Move the request in-use flag into its own bit
array and use that for atomic claims. This cleans up the claim code and
removes any race possibility.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If input validation fails, properly free the request before returning.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If unable to insert node into the RB tree cache, node will be freed
before returning from the function. Null out iovec's pointer to node
so iovec does not try to free it later.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Save the current capability state at user context creation
time. Report this saved value for all shared contexts.
Also get rid of unnecessary hfi1_get_base_kinfo function.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If a context has not been assigned or assignment failed, pq may be NULL.
Move the unregister within the protection of the null check.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Clarify the names of the TID mmu functions.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Checking if the rb tree is empty is redundant with the while loop which is
emptying the rb tree.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rearrange the file open call in prep for new changes.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For bool parameters "false" should be used
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
subctxt is not used, just remove it.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
__mmu_rb_remove was called in only 1 place which was a very simple
call site. Combine this function into its caller.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove, insert, and invalidate are always provided. No
need to test.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This makes it more clear what these functions are
operating on.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parameter names to function declarations make it more clear
what those parameters do.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These are no longer needed.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Brackets should be on the next line of a function
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expand the serial number space by using more bits
from the GUID.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver pads non-double word multiple message sizes but it doesn't
account for this padding when the packet length is calculated. Also, the
data length is miscalculated for message sizes less than 4 bytes due to
the bit representation in LRH. And there's a check for non-double word
multiple message sizes that prevents these messages from being sent.
This patch fixes length miscalculations and enables the functionality to
send non-double word multiple message sizes.
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Checking the return value of the memory allocation call in
init_pervl_scs() was missed. Recently the kmalloc() was changed to
kzalloc() which identified the problem.
While fixing this issue 2 other bugs were noticed. First, the array
being allocated is accessed in the nomem path which can be reached before
it is allocated. Second, kernel_send_context was not released on error.
Fix both of these by creating a more common memory unwind label structure.
Fixes: 35f6befc84 ("staging/rdma/hfi1: Add qp to send context mapping for PIO")
Reported-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of copying the actual GRH of type struct ib_grh, existing code
copies the struct ib_global_route into the sge. This patch fixes that
and constructs the actual GRH from ib_global_route and copies the GRH
into the sge.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The interface is used to compute the 5-bit SC field from the
LRH and the RHF bits. Modify code to use the interface instead.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Cleanup hfi1_ud_rcv to not have to look at the packet
header fields multiple times. The fields are looked up
once and used throughout the function. Also fix sc
computation when validating MAD packets.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
hfi1_pio_header should really be called hfi1_sdma_header
as it is only used for sdma transmits.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
struct ahg_ib_header has no header specific information.
Rename it to struct hfi1_ahg_info
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
sde and hfi1_ib_header are not used anymore.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Active QSFP cables were reset only every alternate iteration of the
channel tuning algorithm instead of every iteration due to incorrect
reset of the flag that controlled QSFP reset, resulting in using stale
QSFP status in the channel tuning algorithm.
Fixes: 8ebd4cf185 ("Add active and optical cable support")
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some QSFP cables assert the interrupt line as a side effect of module
plug-in and power up. This causes the SerDes and QSFP tuning algorithm
to begin cable initialization by reading the QSFP memory map over I2C,
which fails. This patch ignores any interrupt line assertion until
the module has completed power up and voltage rails have stabilized,
which can take a maximum of 500 ms per the SFF-8679 specification.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QSFP CDR enablement is now controlled by determining power class
and the configuration file. We disable the DC 8051 from requesting
enablement or disabling of TX and RX CDRs by removing the code
that allowed the DC 8051 to request changes.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hanging has been observed while writing a file over NFSoRDMA. Dmesg on
the server contains messages like these:
[ 931.992501] svcrdma: Error -22 posting RDMA_READ
[ 952.076879] svcrdma: Error -22 posting RDMA_READ
[ 982.154127] svcrdma: Error -22 posting RDMA_READ
[ 1012.235884] svcrdma: Error -22 posting RDMA_READ
[ 1042.319194] svcrdma: Error -22 posting RDMA_READ
Here is why:
With the base memory management extension enabled, FRMR is used instead
of FMR. The xprtrdma server issues each RDMA read request as the following
bundle:
(1)IB_WR_REG_MR, signaled;
(2)IB_WR_RDMA_READ, signaled;
(3)IB_WR_LOCAL_INV, signaled & fencing.
These requests are signaled. In order to generate completion, the fast
register work request is processed by the hfi1 send engine after being
posted to the work queue, and the corresponding lkey is not valid until
the request is processed. However, the rdmavt driver validates lkey when
the RDMA read request is posted and thus it fails immediately with error
-EINVAL (-22).
This patch changes the work flow of local operations (fast register and
local invalidate) so that fast register work requests are always
processed immediately to ensure that the corresponding lkey is valid
when subsequent work requests are posted. Local invalidate requests are
processed immediately if fencing is not required and no previous local
invalidate request is pending.
To allow completion generation for signaled local operations that have
been processed before posting to the work queue, an internal send flag
RVT_SEND_COMPLETION_ONLY is added. The hfi1 send engine checks this flag
and only generates completion for such requests.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Trace shows incorrect amount of allocated memory.
Fix trace to display memory in KB.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Grzegorz Heldt <grzegorz.heldt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add sysfs entry to allow user to override affinity for SDMA
engine interrupts.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enhance the PCIe Gen3 recipe to support static CTLE tuning,
and add a switch to choose between static and dynamic
approaches. Make discrete chips default to static CTLE
tuning.
Reviewed-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fixes the following warnings with PROVE_LOCKING and PROVE_RCU
enabled in the kernel:
case (1):
[ INFO: suspicious RCU usage. ]
drivers/infiniband/hw/hfi1/init.c:532
suspicious rcu_dereference_check() usage!
case (2):
[ INFO: suspicious RCU usage. ]
drivers/infiniband/hw/hfi1/hfi.h:1624
suspicious rcu_dereference_check() usage!
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Read the version of the SBus, PCIe SerDes, and Fabric Serdes
firmwares at driver load time.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When link up fails in LNI, the local and peer state complete
frames are reported as numbers. Explain what the values mean
so the operator can better diagnose the problem.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, the default number of kernel receive contexts is set to the
number of NUMA nodes on the system plus one for control context. However,
the systems that have a single socket and/or have NUMA disabled in the BIOS
will have only one receive context by default. This patch would ensure that
by default there will be at least two kernel receive contexts plus one for
control context regardless of the number of NUMA nodes on the system. The
user can override the default number of kernel receive contexts with the
krcvqs module parameter.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Advertise and add the capability of handing all aspects of IBTA extended
memory management support in post send.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support extended memory management support, add send side
processing of work requests of type IB_WR_REG_MR, IB_WR_LOCAL_INV, and
IB_WR_SEND_WITH_INV. The first two are local operations and are supported
for both RC and UC. Send with invalidate is only supported for RC because
the corresponding IB opcodes are not defined for UC.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
As part of enabling extended memory management support, add the processing
of the RC send with invalidate.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There were multiple places where FECN/BECN processing was
being done for the different types of QPs. All of that code
was very similar, which meant that it could be pulled into
a single function used by the different QP types.
To retain the performance in the fastpath, the common code
starts with an inline function, which only calls the slow
path if the packet has any of the [FB]ECN bits set.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While handling buffer control MAD, partially initialized
dd->kernel_send_context area may cause potential dereference
of uninitialized pointers. Fix by using kzalloc_node()
instead of kmalloc_node().
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Tymoteusz Kielan <tymoteusz.kielan@intel.com>
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
PMA should not sum TX and RX replay counts when reporting
local link integrity errors. Fixed by removing C_DC_TX_REPLAY
counter from calculation of the link integrity errors counter
value.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Prevent processing receive packet in case when opcode is
accepted by QP but handler for this type of packet is not
defined.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently each user context is assigned a single SDMA engine
based on the VL, context id, and subcontext id. That means for
MPI applications, each rank can only use one SDMA engine for
all messages. This may create unwanted backup for independent
messages going to different destinations upon congestion at one
destination.
This patch adds the packet "dlid" to the formula of SDMA engine
selection for user SDMA requests. A simple hash table is used
to maintain even distribution among the available SDMA engines
regardless how the "dlid" values are distributed.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove the TWSI code. The driver now uses the kernel's built-in
i2c bit bus module.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use built-in i2c bit-shift bus adapter to control the
i2c busses on the chip.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When performing process affinity recommendations for MPI ranks, the current
algorithm doesn't take into account multiple HFI units. Also, real
cores and HT cores are not distinguished from one another. Therefore,
all HT cores are recommended to be assigned first within the local NUMA
node before recommending the assignments of cores in other NUMA nodes.
It's ideal to assign all real cores across all NUMA nodes first, then all
HT 1 cores, then all HT 2 cores, and so on to balance CPU workload. CPU
cores in other NUMA nodes could be running interrupt handlers, and this is
not taken into account.
To balance the CPU workload for user processes, the following
recommendation algorithm is used:
For each user process that is opening a context on HFI Y:
a) If all cores are assigned to user processes, start assignments all
over from the first core
b) Assign real cores first, then HT cores (First set of HT cores on
all physical cores, then second set of HT cores, and, so on) in the
following order:
1. Same NUMA node as HFI Y and not running an IRQ handler
2. Same NUMA node as HFI Y and running an IRQ handler
3. Different NUMA node to HFI Y and not running an IRQ handler
4. Different NUMA node to HFI Y and running an IRQ handler
c) Mark core as assigned in the global affinity structure. As user
processes are done, remove core assignments from global affinity
structure.
This implementation allows an arbitrary number of HT cores and provides
support for multiple HFIs.
This is being included in the kernel rather than user space due to the
fact that user space has no way of knowing the CPU recommendations for
contexts running as part of other jobs.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Kernel receive queues oversubscribe CPU cores on multi-HFI systems.
To prevent this, the kernel receive queues are separated onto
different cores, and the SDMA engine interrupts are constrained to
a lesser number of cores.
hfi1s_on_numa_node*krcvqs is the number of CPU cores that are
reserved for kernel receive queues for all HFIs. Each HFI initializes
its kernel receive queues to one of the reserved CPU cores. If there
ends up being 0 CPU cores leftover for SDMA engines, use the same
CPU cores as receive contexts.
In addition, general and control contexts are assigned to their own
CPU core, however, both types of contexts tend to have low traffic.
To save CPU cores, collapse general and control contexts to one CPU
core for all HFI units. This change prevents SDMA engine interrupts
from wrapping around general contexts.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When HFI units get initialized, they each use their own mask copy for
affinity assignments. On a multi-HFI system, affinity assignments
overbook CPU cores as each HFI doesn't have knowledge of affinity
assignments for other HFI units. Therefore, some CPU cores are never
used for interrupt handlers in systems with high number of CPU cores
per NUMA node.
For multi-HFI systems, SDMA engine interrupt assignments start all over
from the first CPU in the local NUMA node after the first HFI
initialization. This change allows assignments to continue where the
last HFI unit left off.
Add global structure for affinity assignments for multiple HFIs to share
affinity mask.
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The q-counter-id is given in modify-QP command associates
the QP with the counter. The offset to which the counter
ID was set is incorrect, causing IB port counters not to
count on QP.
Fixes: 0837e86a7a ('IB/mlx5: Add per port counters')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Number of outstanding_pi may overflow and as a result may indicate that
there are no elements in the queue. The effect of doing this is that the
MAD layer will get stuck waiting for completions. The MAD layer will
think that the QP is full - because it didn't receive these completions.
This fix changes it so the outstanding_pi number is increased
with 32-bit wraparound and is not limited to max_send_wr so
that the difference between outstanding_pi and outstanding_ci will
really indicate the number of outstanding completions.
Cc: Stable <stable@vger.kernel.org>
Fixes: ea6dc20362 ('IB/mlx5: Reorder GSI completions')
Signed-off-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
i40iw_puda_get_listbuf may return NULL if the list is empty.
Add NULL check prior to accessing the pointer.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change dup_ack_thressh to u8 since it is a 3 bit field.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_cq_poll_completion, we always move the tail. So there is
no reason to check for overflow everytime we move the head.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Replace a subtract and multiply with an add; while populating fragments
in SQ wqe.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Child_listen_node pointer is used in a debug print after kfree.
Move the print before kfree.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix size parameter passed to i40iw_reg_phys_mr and use it to
register memory.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Blocking in c4iw_destroy_qp() causes a deadlock when apps destroy a qp
or disconnect a cm_id from their cm event handler function. There is
no need to block here anyway, so just replace the refcnt atomic with a
kref object and free the memory on the last put.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This forces the connection to abort if the application failed to
disconnect before flushing. This is aligned with how the common
flush services work.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There exists a race where the application can setup a connection
and then disconnect it before iw_cxgb4 processes the fw4_ack
message. For passive side connections, the fw4_ack message is
used to know when to stop the ep timer for MPA_REPLY messages.
If the application disconnects before the fw4_ack is handled then
c4iw_ep_disconnect() needs to clean up the timer state and stop the
timer before restarting it for the disconnect timer. Failure to do this
results in a "timer already started" message and a premature stopping
of the disconnect timer.
Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Elsewhere the sin_family field holds a value with a name of the form
AF_..., so it seems reasonable to do so here as well. Also the values
of PF_INET and AF_INET are the same.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
struct sockaddr_in sip;
@@
(
sip.sin_family ==
- PF_INET
+ AF_INET
|
sip.sin_family !=
- PF_INET
+ AF_INET
|
sip.sin_family =
- PF_INET
+ AF_INET
)
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The commit 0f8ab0b6e9 ("RDMA/iw_cxgb4: Low resource fixes for Memory
registration") from Jun 10, 2016, leads to the following static checker
warning:
drivers/infiniband/hw/cxgb4/mem.c:612 c4iw_alloc_mw()
error: use kfree_skb() here instead of kfree(mhp->dereg_skb)
Also fixes skb leak in c4iw_dealloc_mw
Fixes: 0f8ab0b6e9 ("RDMA/iw_cxgb4: Low resource fixes for Memory registration")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add sw counter to track dropped unsupported packets.
Report unsupported packets drop as the RcvError.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add per VL XmitDiscards counters to the opapmaquery
status and error response.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix sparse errors by making sure the fast assign destinations
are host cpu typed.
For the void __iomem *, just make the field match source
data.
Fix a bug where the hw_free trace printed the pointer vs.
the dereferenced value.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ftrace infrastructure used to evaluate the TRACE_SYSTEM
macro on every DEFINE_EVENT() macro. Now the TRACE_SYSTEM
macro only gets evaluated when trace/define_trace.h is
included, so the group event information is lost. This was
introduced in
commit acd388fd3a ("tracing: Give system name a pointer")
Therefore, each system tracepoint must be on its own file.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix a copy and paste typo in comment.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simple code clean up of hfi1_write_iter.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The definition of port state changed mid development and the
old structure was kept accidentally. Remove this dead code.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for writing the tx descriptor from multiple functions,
create a helper for both normal and blueflame access.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i40iw_create_cqp() printed the contents of variables maj_err and min_err
in an error message before they could be initialized (by calling
dev->cqp_ops->cqp_create).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The critical section should protect only the list traversal
and dd->asic_data modification, not the memory allocation.
The fix pulls the allocation out of the critical section.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There are several computatations of the sc in the
ud receive routine.
Besides the code duplication, all are wrong when the
sc is greater than 15. In that case the code incorrectly
or's a 1 into the computed sc instead of 1 shifted left
by 4.
Fix precomputed sc5 by using an already implemented routine
hdr2sc() and deleting flawed duplicated code.
Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the firmware version through the core.
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove sysfs file in favor of the common core.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove sysfs in favor of the core support.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove the sysfs in favor of the core version.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove the sysfs entry in favor of the core support.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove sysfs entry in favor of the common code.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove the sysfs in favor of common core version.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove sysfs support in favor of the core version.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
And remove sysfs fw_ver in favor of the core.
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Also remove fw_ver sysfs to be replaced by the common core one.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose new counters using the get protocol stats callback.
We expose the following counters:
|------------------------------------------------------------------------|
| Name | IB | EN | Description |
|------------------------------------------------------------------------|
|rx_write_requests | + | - | Number of received WRITE requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|rx_read_requests | + | - | Number of received READ requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|rx_atomic_requests | + | - | Number of received ATOMIC requests for |
| | | | the associated QP. |
|------------------------------------------------------------------------|
|out_of_buffer | + | + | Number of drops occurred due to lack |
| | | | of WQE for the associated QPs/RQs. |
|------------------------------------------------------------------------|
|out_of_sequence | + | - | Number of errors in the packet |
| | | | transport sequence number |
|------------------------------------------------------------------------|
|duplicate_request | + | + | Number of received duplicated packets. |
| | | | A request that previously executed is |
| | | | named duplicated. |
|------------------------------------------------------------------------|
|rnr_nak_retry_err | + | + | Number of received RNR NAC packets. |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
|packet_seq_err | + | + | Number of received NAK - sequence error|
| | | | packets. The QP retry limit did not |
| | | | exceed. |
|------------------------------------------------------------------------|
|implied_nak_err | + | + | Number of times the requester detected |
| | | | an ACK with a PSN larger than expected |
| | | | PSN for RDMA READ or ATOMIC response |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
|local_ack_timeout_err| + | - | Number of NO ACK responses from |
| | | | responder within timer interval. |
| | | | The QP retry limit did not exceed. |
|------------------------------------------------------------------------|
Counters are available if all of them are supported.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support statistics for ports, we attach
each QP to a counter set which is dedicate to this port.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, the SRQ API uses the obsolete mlx5_*_srq_mbox_{in,out}
structs which limit the ability to pass the SRQ attributes between
net and IB parts of the driver.
This patch changes the SRQ API so as to use auto-generated structs
and provides a better way to pass attributes which will be in use by
coming features.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable mlx5 based hardware to report TCP segmentation offload (TSO)
capabilities from kernel to user space. A TSO enabled NIC will accept
big chunks of data with sizes greater than MTU for TCP traffic. The TSO
engine will break the data into separate packets and will insert headers
automatically.
The capabilities are exposed to user space through query_device by uhw
directly. The following capabilities are reported:
1. The maximum payload size in bytes supported for segmentation by TSO
engine.
2. Bitmap showing which QP types are supported by TSO operation. The bitmap
is built by members from 'enmu ib_qp_type'. For example, similar code
should be performed if UD QP is supported:
supported_qpts |= 1 << IB_QPT_UD;
To make user-space library aware of whether kernel supports uhw or not, a
new flag: cmds_supp_uhw will be returned back to user-space through
alloc_ucontext.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable flow steering for IPv6 traffic by using an IPv6 spec.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver exposes interfaces that directly relate to HW state.
Upon fatal error, consumers of these interfaces (ULPs) that rely
on completion of all their posted work-request could hang, thereby
introducing dependencies in shutdown order. To prevent this from
happening, we manage the relevant resources (CQs, QPs) that are used
by the device. Upon a fatal error, we now generate simulated
completions for outstanding WQEs that were not completed at the
time the HW was reset.
It includes invoking the completion event handler for all involved
CQs so that the ULPs will poll those CQs. When polled we return
simulated CQEs with IB_WC_WR_FLUSH_ERR return code enabling ULPs
to clean up their resources and not wait forever for completions
upon receiving remove_one.
The above change requires an extra check in the data path to make
sure that when device is in error state, the simulated CQEs will
be returned and no further WQEs will be posted.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implements the IB core disassociate_ucontext API.
The driver detaches the HW resources for a given user context to
prevent a dependency between application termination and device
disconnect. This is done by managing the VMAs that were mapped
to the HW bars such as doorbell and blueflame. When need to detach,
remap them to an arbitrary kernel page returned by the zap API.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for Raw Ethernet RX HASH QP. Currently, creation and
destruction of such a QP are supported. This QP is implemented as
a simple TIR object which points to the receive RQ indirection table.
The given hashing configuration is used to configure the TIR and by
that it chooses the right RQ from the RQ indirection table.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some mlx5 based hardwares support a RQ table object. This RQ table
points to a few RQ objects. We implement the receive work queue
indirection table API (create and destroy) by using this hardware
object.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A QP can be created without internal WQs "packaged" inside it,
this QP can be configured to use "external" WQ object as its
receive/send queue.
WQ is a necessary component for RSS technology since RSS mechanism
is supposed to distribute the traffic between multiple
Receive Work Queues
Receive WQs are implemented by RQs.
Implement the WQ creation, modification and destruction verbs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pre-allocate buffers to deallocate completion queue, so that completion
queue is deallocated during RDMA termination when system is running
out of memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pre-allocate buffers for deregistering memory region and memory window
during RDMA connection close, when system is running out of memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pre-allocate buffers for sending various control messages to close
connection, abort connection, etc so that we gracefully handle
connections when system is running out of memory.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Get rid of unneeded code, and refactor things a bit.
For MPA version 0 we abort the connection. For > 0, we attempt to send
an MPA_START/REJECT Reply, and then disconnect gracefully. If the send
of the MPA message fails, then we abort the connection. We can ignore
c4iw_ep_disconnect() errors here because it will clean up the endpoint
if there are failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
With IPv6 addresses, the "qps" debugfs is running out of space and
truncating the output. Bump the required size accordingly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
markers_enabled should be read only once during MPA negotiation.
The present code does read markers_enabled twice during negotiation
which results in setting wrong recv/xmit markers if the markers_enabled is
changed in the middle of negotiation.
With this change the markers_enabled is read only once during MPA
negotiation. recv markers are set based on markers enabled module
parameter and xmit markers are set based on markers flag from the
MPA_START_REQ/MPA_START_REP.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the chunk_size to enable level-1 PBL support when the fast memory
page count is more than one.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
CQ is armed for solicited events only, ignoring other notification
flags. Correct this by arming for next and arming for solicited
event if IB_CQ_SOLICITED is set. Also protect CQ shadow area update
with spinlock.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A failure in the get_txreq() inline will result in a
slow path retry using __get_txreq().
__get_txreq() attempts to procure the qp s_lock, which
is already held in all callers.
Fix by deleting the s_lock maintenance in __get_txreq()
and add sparse syntax hooks to future proof the code.
Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Prevent cross page boundary allocation by allocating
new page, this is required to be aligned with ConnectX-3 HW
requirements.
Not doing that might cause to "RDMA read local protection" error.
Fixes: 1b2cd0fc67 ('IB/mlx4: Support the new memory registration API')
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When RC, UC, or RAW QPs are created, a qp object is allocated (kzalloc).
If at a later point (in procedure create_qp_common) the qp creation fails,
this qp object must be freed.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In procedure mlx4_ib_create_flow, passing an invalid port number
will cause an out-of-bounds array access. Data passed to this procedure
can come from user-space. Therefore, need to validate port number
before proceeding onwards.
Note that we check against the number of physical ports declared at
the verbs (ib core) level; When bonding is active, the verbs level
sees one physical port, even though the low-level driver sees two ports.
Fixes: f77c0162a3 ("IB/mlx4: Add receive flow steering support")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix mad send error flow to prevent double freeing address handles,
and leaking tx_ring entries when SRIOV is active.
If ib_mad_post_send fails, the address handle pointer in the tx_ring entry
must be set to NULL (or there will be a double-free) and tx_tail must be
incremented (or there will be a leak of tx_ring entries).
The tx_ring is handled the same way in the send-completion handler.
Fixes: 37bfc7c1e8 ("IB/mlx4: SR-IOV multiplex and demultiplex MADs")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When calculating the required size of an RC QP send queue, leave
enough space for masked atomic operations, which require more space than
"regular" atomic operation.
Fixes: 6fa8f71984 ("IB/mlx4: Add support for masked atomic operations")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
port_xmit_data is written instead of port_rcv_data.
Fixes: 3efd9a1121 ('IB/mlx5: Modify MAD reading counters method to use counter registers')
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the caller specified IB_SEND_FENCE in the send flags of the work
request and no previous work request stated that the successive one
should be fenced, the work request would be executed without a fence.
This could result in RDMA read or atomic operations failure due to a MR
being invalidated. Fix this by adding the mlx5 enumeration for fencing
RDMA/atomic operations and fix the logic to apply this.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Swapping a cable from a "Mgmt Allowed=No" switch port to a
"Mgmt Allowed=Yes" switch port doesn't send a pkey change
notification. Therefore, the link doesn't become active as
the oib_utils layer uses an old pkey table cache.
Fix by ensuring the pkey change notification is sent when
the table is changed both explicitly by the FM and implicitly
by the driver via a cable swap.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
FULL_MGMT_P_KEY doesn't get cleared from the pkey table at link bounce
because the link down and link bounce code paths are different when
moving a QSFP cable on a switch. This causes an HFI unit connected to a
switch to try to be initialized to an FM node when the QSFP cable is
moved from a MgmtAllowed=NO port to a MgmtAllowed=YES port and back to a
MgmtAllowed=NO port. Remove FULL_MGMT_P_KEY from pkey table at link up.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fixes potential buffer overflow because the sprintf function
doesn't check buffer boundaries. Use snprintf instead.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fixes potential NULL ptr dereference because IS_ERR(dd) doesn't
handle NULL. Fix the issue by initializing the pointer with a not NULL
error code.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If a context has already been assigned to an FD, prevent
another assignment.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If a context has already been assigned to an FD, prevent
another assignment.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current value of 500us for the packet egress timeout is too small
which causes the host to declare failure on draining packets too early
and unnecessarily bounces the link. Increase this to 50ms taking into
account the switch packet discard timer default and the worst case
per-VL package drainage rate.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The credit return threshold adjustment on mtu change algorithm does not
take into account all the kernel send contexts that are assigned per VL.
Use the pio send context map to adjust the credit return thresholds for
all the allocated and assigned kernel send contexts based on the MTU
adjustment per VL.
The pio send context map can be changed dynamically based on the actual
number of operational vls which is set by the fabric manager. When this
happens update the credit return threshold values for all the remapped
kernel send contexts.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When this code was reworked for IBoE support the order of assignments
for the sl_tclass_flowlabel got flipped around resulting in
TClass & FlowLabel being permanently set to 0 in the packet headers.
This breaks IB routers that rely on these headers, but only affects
kernel users - libmlx4 does this properly for user space.
Cc: stable@vger.kernel.org
Fixes: fa417f7b52 ("IB/mlx4: Add support for IBoE")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Userspace flag IBV_QP_ALT_PATH is supposed to set the alternate path
including fields alt_pkey_index and alt_timeout.
Added IB_QP_PKEY_INDEX and IB_QP_TIMEOUT to the attribute mask when
calling mlx5_set_path for the alternate path to force setting the
alt_pkey_index and alt_timeout values.
Fixes: bf24481a3a7c4 ('IB/mlx5: Consider alternate path in pkey ...')
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pkey index fields in the QP context path record are extended to 16
bits, as required by IB spec (version 1.3).
This change affects all QP commands which include path records.
To enable this change, moved the free adaptive routing flag bit
(free_ar) to the most significant byte of the QP path record.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB ...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Verify that number of entries is less than device capability.
Add an appropriate warning message for error flow.
Fixes: bde51583f4 ('IB/mlx5: Add support for resize CQ')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Number of entries shouldn't be greater than the device's max
capability. This should be checked before rounding the entries number
to power of two.
Fixes: 51ee86a4af ('IB/mlx5: Fix check of number of entries...')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
BlueFlame support is reported only for PFs when the HCA capability is
on.
Fixes: 938fe83c8d ('net/mlx5_core: New device capabilities...')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When PAGE_SIZE is larger than 4K, the user shouldn't be able to query
the HCA core clock. This counter is within 4KB boundary and the
user-space shall not read information that's after this boundary.
Fixes: b368d7cb8c ('IB/mlx5: Add hca_core_clock_offset to...')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a 4-digit padding to show FW version in proper format.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from...')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
FW port-change events are fired on Active <-> non Active port state
transitions only.
When the port state changes from Active to Initializing (Active ->
Down -> Initializing), a single event is fired.
The HCA transitions from Down to Initializing unless prevented from
doing so, hence the driver should also propagate events when the port
state is Initializing to consumers so they'll be aware that the port
is no longer Active and act accordingly.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Flow steering is supported by mlx5 device when the following
features are supported by firmware:
1. NIC RX flow table.
2. Device has enough flow steering levels.
3. Atomic modification of flow table entry.
4. Flow tables chaining.
To check if flow steering is supported it's enough to check
if the driver opened the mlx5 bypass namespace.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that sparse reports the following warnings for the hfi1 driver:
trace.c:217:13: warning: no previous prototype for ‘print_u64_array’ [-Wmissing-prototypes]
user_sdma.c:1361:17: warning: dubious: !x & y
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The first argument of test_bit() and clear_bit() is a bit number and
not a bitmask. Hence change that first argument from (1 << 0) into 0.
This patch avoids that smatch reports the following warnings:
user_sdma.c:1059: sdma_cache_evict() warn: test_bit() takes a bit number
user_sdma.c:1590: sdma_rb_remove() warn: test_bit() takes a bit number
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make the indentation of the source code consistent. Detected by
smatch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Perform the test for device managed flow steering support even if
memory windows are not supported. I noticed this because smatch
reported inconsistent indentation for the device managed flow
steering support test.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The DMA attributes are set but never used.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When CONFIG_FRAME_WARN is set to 1024 bytes, which is useful to find
stack consumers, we get a warning in hfi1 driver.
drivers/infiniband/hw/hfi1/affinity.c: In function
‘hfi1_get_proc_affinity’:
drivers/infiniband/hw/hfi1/affinity.c:415:1: warning: the frame size of
1056 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This change removes unneeded buf[1024] declaration and usage.
Fixes: f48ad614c1 ("IB/hfi1: Move driver out of staging")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
That extra tabs are misleading.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Dynamic counter infrastructure in the IB drivers
This is a sysfs based code to allow free form access to the hardware
counters RDMA devices might support so drivers don't need to code
this up repeatedly themselves
- SendOnlyFullMember multicast support
- IB router support
- A couple misc fixes
- The big item on the list: hfi1 driver updates, plus moving the hfi1
driver out of staging
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5+cf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"This is the second group of code for the 4.7 merge window. It looks
large, but only in one sense. I'll get to that in a minute. The list
of changes here breaks down as follows:
- Dynamic counter infrastructure in the IB drivers
This is a sysfs based code to allow free form access to the
hardware counters RDMA devices might support so drivers don't need
to code this up repeatedly themselves
- SendOnlyFullMember multicast support
- IB router support
- A couple misc fixes
- The big item on the list: hfi1 driver updates, plus moving the hfi1
driver out of staging
There was a group of 15 patches in the hfi1 list that I thought I had
in the first pull request but they weren't. So that added to the
length of the hfi1 section here.
As far as these go, everything but the hfi1 is pretty straight
forward.
The hfi1 is, if you recall, the driver that Al had complaints about
how it used the write/writev interfaces in an overloaded fashion. The
write portion of their interface behaved like the write handler in the
IB stack proper and did bi-directional communications. The writev
interface, on the other hand, only accepts SDMA request structures.
The completions for those structures are sent back via an entirely
different event mechanism.
With the security patch, we put security checks on the write
interface, however, we also knew they would be going away soon. Now,
we've converted the write handler in the hfi1 driver to use ioctls
from the IB reserved magic area for its bidirectional communications.
With that change, Intel has addressed all of the items originally on
their TODO when they went into staging (as well as many items added to
the list later).
As such, I moved them out, and since they were the last item in the
staging/rdma directory, and I don't have immediate plans to use the
staging area again, I removed the staging/rdma area.
Because of the move out of staging, as well as a series of 5 patches
in the hfi1 driver that removed code people thought should be done in
a different way and was optional to begin with (a snoop debug
interface, an eeprom driver for an eeprom connected directory to their
hfi1 chip and not via an i2c bus, and a few other things like that),
the line count, especially the removal count, is high"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (56 commits)
staging/rdma: Remove the entire rdma subdirectory of staging
IB/core: Make device counter infrastructure dynamic
IB/hfi1: Fix pio map initialization
IB/hfi1: Correct 8051 link parameter settings
IB/hfi1: Update pkey table properly after link down or FM start
IB/rdamvt: Fix rdmavt s_ack_queue sizing
IB/rdmavt: Max atomic value should be a u8
IB/hfi1: Fix hard lockup due to not using save/restore spin lock
IB/hfi1: Add tracing support for send with invalidate opcode
IB/hfi1, qib: Add ieth to the packet header definitions
IB/hfi1: Move driver out of staging
IB/hfi1: Do not free hfi1 cdev parent structure early
IB/hfi1: Add trace message in user IOCTL handling
IB/hfi1: Remove write(), use ioctl() for user cmds
IB/hfi1: Add ioctl() interface for user commands
IB/hfi1: Remove unused user command
IB/hfi1: Remove snoop/diag interface
IB/hfi1: Remove EPROM functionality from data device
IB/hfi1: Remove UI char device
IB/hfi1: Remove multiple device cdev
...
In practice, each RDMA device has a unique set of counters that the
hardware implements. Having a central set of counters that they must
all adhere to is limiting and causes many useful counters to not be
available.
Therefore we create a dynamic counter registration infrastructure.
The driver must implement a stats structure allocation routine, in
which the driver must place the directory name it wants, a list of
names for all of the counters, an array of u64 counters themselves,
plus a few generic configuration options.
We then implement a core routine to create a sysfs file for each
of the named stats elements, and a core routine to retrieve the
stats when any of the sysfs attribute files are read.
To avoid excessive beating on the stats generation routine in the
drivers, the core code also caches the stats for a short period of
time so that someone attempting to read all of the stats in a
given device's directory will not result in a stats generation
call per file read.
Future work will attempt to standardize just the shared stats
elements, and possibly add a method to get the stats via netlink
in addition to sysfs.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[ Add caching, make structure names more informative, add i40iw support,
other significant rewrites from the original patch ]
The pio map initialization function is off by 1 causing the last
kernel send context that is allocated to not get mapped into the
pio map which leads to the last kernel send context not being used
by any of the qps.
The send context reserved for VL15 is taken care of by setting the
scontext variable that is used as the index into the kernel send
context array to 1 and does not need to be accounted for in the
kernel send context counting loop as it is currently done.
Fix the kernel send context counting loop to account for all the
allocated send contexts and map all of them to the different VLs.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Two 8051 link settings, external device config and tuning method,
were written in the wrong location and the previous settings were
not cleared. For both, clear the old value and write the new
value.
Fixes: 8ebd4cf185 ("staging/rdma/hfi1: Add active and optical cable support")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When FM is disabled, and the HFI port on the switch is
changed from MgmtAllowed=YES to MgmtAllowed=NO and the
link is bounced, FULL_MGMT_P_KEY doesn't get cleared
from the pkey table. This also occurs when the QSFP
cable is moved from a switch port with MgmtAllowed=YES
to a MgmtAllowed=NO port. Clear pkey entry properly.
Also, when the driver is loaded and the switch port is
set to MgmtAllowed=NO, FULL_MGMT_P_KEY shouldn't be added
to pkey table after FM is started. Only set FULL_MGMT_P_KEY
in the pkey table if switch port is configured to
MgmtAllowed=YES.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit b9b06cb6fe
("IB/hfi1: Fix missing lock/unlock in verbs drain callback")
added a spin lock.
Unfortunately, the new lock code can be called from a base
level interrupt state, and an interrupt that can get stacked
will attempt to get the same lock.
Fix by using the flag save/restore spin lock variation.
Cc: stable@vger.kernel.org # 4.6+
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable trace generation for packets with the "Send Last with
Invalidate" and "Send Only with Invalidate" opcodes.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A new union member "ieth" (Invalidate Extended Transport Header) is
added to the packet header definition in preparation of supporting
the send with invalidate opcode.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Building the qib driver with gcc version 6.1.0 raises the following
build warning:
drivers/infiniband/hw/qib/qib_iba7322.c:1311:39: warning:
'qib_7322_intr_msgs' defined but not used [-Wunused-const-variable=]
static const struct qib_hwerror_msgs qib_7322_intr_msgs[] = {
^~~~~~~~~~~~~~~~~~
Remove the unused qib_7322_intr_msgs[]
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change struct ib_class_port_info to conform to IB Spec 1.3
That in order to get specific capability mask from ClassPortInfo mad.
>From the IB Spec, ClassPortInfo section:
"CapabilityMask2 Bits 0-26: Additional class-specific capabilities...
RespTimeValue the rest 5 bits"
The new struct now has one field for capabilitymask2 (previously was the
reserved field) and the resp_time field.
And it fixes up qib and srpt, use of the field repurposed to be used as
capabilitymask2:
IB/qib: Change pma_get_classportinfo
IB/srpt: Adjust the use of ib_class_port_info
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+Zv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Primary 4.7 merge window changes
- Updates to the new Intel X722 iWARP driver
- Updates to the hfi1 driver
- Fixes for the iw_cxgb4 driver
- Misc core fixes
- Generic RDMA READ/WRITE API addition
- SRP updates
- Misc ipoib updates
- Minor mlx5 updates"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (148 commits)
IB/mlx5: Fire the CQ completion handler from tasklet
net/mlx5_core: Use tasklet for user-space CQ completion events
IB/core: Do not require CAP_NET_ADMIN for packet sniffing
IB/mlx4: Fix unaligned access in send_reply_to_slave
IB/mlx5: Report Scatter FCS device capability when supported
IB/mlx5: Add Scatter FCS support for Raw Packet QP
IB/core: Add Scatter FCS create flag
IB/core: Add Raw Scatter FCS device capability
IB/core: Add extended device capability flags
i40iw: pass hw_stats by reference rather than by value
i40iw: Remove unnecessary synchronize_irq() before free_irq()
i40iw: constify i40iw_vf_cqp_ops structure
IB/mlx5: Add UARs write-combining and non-cached mapping
IB/mlx5: Allow mapping the free running counter on PROT_EXEC
IB/mlx4: Use list_for_each_entry_safe
IB/SA: Use correct free function
IB/core: Fix a potential array overrun in CMA and SA agent
IB/core: Remove unnecessary check in ibnl_rcv_msg
IB/IWPM: Fix a potential skb leak
RDMA/nes: replace custom print_hex_dump()
...
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
Previously, mlx5_ib_cq_comp was executed from interrupt context.
Under heavy load, this could cause the CPU core to be in an interrupt
context too long.
Instead of executing the handler from the interrupt context we
execute it from a much friendly tasklet context.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The problem is that the function 'send_reply_to_slave' gets the
'req_sa_mad' as a pointer whose address is only aliged to 4 bytes
but is 8 bytes in size. This can result in unaligned access faults
on certain architectures.
Sowmini Varadhan pointed to this reply from Dave Miller that say
that memcpy should not be used to solve alignment issues:
https://lkml.org/lkml/2015/10/21/352
Optimization of memcpy to 'ldx' instruction can only happen if the
compiler knows that the size of the data we are copying is 8 bytes
and it assumes it is aligned to 8 bytes. If the compiler know the
type is not aligned to 8 it must not optimize the 8 byte copy.
Defining the data type as aligned to 4 forces the compiler to treat
all accesses as though they aren't aligned and avoids the 'ldx'
optimization.
Full credit for the idea goes to Jason Gunthorpe
<jgunthorpe@obsidianresearch.com>.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Report Scatter FCS support when the Firmware supports as well.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable Scatter FCS in the RQ context when the user passes
Scatter FCS create flag.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
By this patch, the user space library will be able to improve
performance using appropriate ringing DoorBell method according to the
memory type it asked for.
Currently only one mapping command is allowed for UARs:
MLX5_IB_MMAP_REGULAR_PAGE. Using this mapping, the kernel maps the
UARs to write-combining (WC) if the system supports it.
If the system is not supporting WC the UARs are mapped to
non-cached(NC). In this case the user space library can't tell which
mapping is applied.
This patch adds 2 new mapping commands: MLX5_IB_MMAP_WC_PAGE and
MLX5_IB_MMAP_NC_PAGE. For these commands the kernel maps exactly as
requested and fails if it can't.
Since there is no generic way to check if the requested memory region
can be mapped as WC, driver enables conclusive WC mapping only for
x86, PowerPC and ARM which support WC for the device's memory region.
Signed-off-by: Guy Levy <guyle@mellanox.com>
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current mlx5 code disallows mapping the free running counter of
mlx5 based hardwares when PROT_EXEC is set.
Although this behaviour is correct, Linux does add an implicit VM_EXEC
to the vm_flags if the READ_IMPLIES_EXEC bit is set in the process
personality. This happens for example if the process stack is
executable.
This causes libmlx5 to output a warning and prevents the user from
reading the free running clock.
Executing the init segment of the hardware isn't a security risk
(at least no more than executing a process own stack), so we just
prevent writes to there.
Fixes: d69e3bcf79 ('IB/mlx5: Mmap the HCA's core clock register to
user-space')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simplify the code in search_relocate_mgid0_group with by using
list_for_each_entry_safe().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no need to duplicate a lot of code that is in the kernel library for ages.
Replace duplicating code by calling to print_hex_dump() directly.
Note that output is slightly changed:
- hex and ascii parts have just two spaces delimeter
- there is no delimeter for ascii portions
- file and line removed from prefix (they were redundant anyway since previous
output shows same closer enough)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
fix spelling mistake, argumant -> argument
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This function compiles to 550 bytes of machine code.
Three callsites, all in nes_create_qp.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Faisal Latif <faisal.latif@intel.com>
CC: Doug Ledford <dledford@redhat.com>
CC: linux-rdma@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Reviewed-By: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding sq and rq drain functions, which block until all
previously posted wr-s in the specified queue have completed.
A completion object is signaled to unblock the thread,
when the last cqe for the corresponding queue is processed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
__force casts should be avoided if there is a better alternative.
Hence modify the comparison of s_addr with INADDR_ANY such that the
__force cast is no longer necessary.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Vipul Pandya <vipul@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These handlers when called print error message to the kernel log,
but the actual handling is done by _c4iw_free_ep() and process_timeout().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently c4iw_peer_abort_intr() does not wake up the waiter if the
endpoint state indicates we're using MPAv2 and we're currently trying to
connect. This was introduced with commit 7c0a33d611 ("RDMA/cxgb4:
Don't wakeup threads for MPAv2")
However, this original fix is flawed because it introduces a race that
can cause a deadlock of the iwarp stack. Here is the race:
->local side sets up an active offload connection.
->local side sends MPA_START request.
->peer sends MPA_START response.
->local side ingress cpl thread begins processing the MPA_START response,
but before it changes the state from MPA_REQ_SENT to FPDU_MODE:
->peer sends a RST which results in a ABORT_REQ_RSS. This triggers
peer_abort_intr() which sees the state in MPA_REQ_SENT and since mpa_rev
is 2, it will avoid waking up the endpoint with -ECONNRESET, assuming the
stack will re-attempt the connection using MPAv1.
->Meanwhile, the cpl thread moves the state to FPDU_MODE and calls
c4iw_modify_rc_qp() which calls rdma_init() which sends a RI_WR/INIT WR
to firmware. But since HW sent an abort, FW correctly drops the RI_WR/INIT
WR.
->So the cpl thread is stuck waiting for a reply and cannot process the
ABORT_REQ_RSS cpl sitting in its input queue. Thus everything comes to a
halt because no more ingress cpls are processed by the stack...
The correct fix for the issue is to always do the wake up in
c4iw_abort_intr() but reinitialize the wait object in c4iw_reconnect().
Fixes: 7c0a33d611 ("RDMA/cxgb4: Don't wakeup threads for MPAv2")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add get_ep_from_stid() which will atomically find and reference the
endpoint struct if found. This avoids touch-after-free races between
threads destroying listening endpoints and the CPL processing thread
processing an incoming PASS_ACCEPT_REQ CPL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
c4iw_reject() and c4iw_accept() need to handle the case where the
endpoint has timed out and is in the middle of ABORTING the connection.
Here is the flow that causes the BUG_ON() to fire on the server side:
1) offload connection setup and endpoint timer started
2) MPA_START request received from peer, CONNECT_REQUEST passed to ULP
3) endpoint timer fires, and process_timeout() aborts the connection,
this moves the endpoint state to ABORTING until HW sends up the
ABORT_RPL_RSS.
4) application exits closing the CONNECT_REQUEST cm_id. The IWCM calls
c4iw_reject_cr() to destroy this connection request.
5) WHAMO: BUG_ON() because the state is ABORTING.
The fix is to change c4iw_reject_cr() and c4iw_accept_cr() to fail the
operation if the state is not in MPA_REQ_RCVD vs in DEAD.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ARP failure may also happen when ep in FPDU_MODE and these failures need
to be handled by process_timeout(). process_timeout() also has to handle
case MPA_REQ_RCVD, setting abort to 1, leading to ep resource release.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Arp failure for send_mpa_reply/reject() is handled by freeing the
mpa_skb in c4iw_free_ep() before releasing ep.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a race between ULP threads calling c4iw_ep_disconnect() via
c4iw_modify_rc_qp() and the ingress CPL thread where the ULP thread
can free the endpoint just after the ingress CPL thread finds the ep
pointer in the tid table. To avoid this, we now use the hwtid_idr table
for lookups instead of the LLD tid table so we can lock around insert,
remove, and lookup+get_ep to avoid the race. The CPL handlers now will
either find the ep ptr and have a ref on it, or not find it and they
can discard the CPL. Callers of get_ep_from_tid() will have a ref
on the ep if found, and thus must deref when they are done.
Negative advice in peer_abort_intr() need to dereference the ep.
therefore peer_abort() is scheduled to dereference the ep later.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In abort_arp_failure(), the return value from c4iw_ofld_send() is
ignored and thus if the CPL isn't sent, the endpoint is stuck and never
gets aborted. Failure of c4iw_ofld_send() is treated as fatal error, and
the ep resources are released in a safer context through process_work().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Moving the state to ABORTING causes the ep to get stuck because
c4iw_ep_timeout() thinks the ABORT has already been done. So leave the
state alone and let c4iw_ep_disconnect() do the right thing given the
ep state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
->In act_open_rpl(), CPL_ERR_TCAM_FULL error handling branch, there is
no handling of the return value of send_fw_act_open_req().
->In send_fw_act_open_req(), there is no handling of return value of
c4iw_l2t_send(), which may cause a ep leak and won't notify upper layers
on connection establish failure.
->send_mpa_req() should act on the return from c4iw_l2t_send() and
return the error to the caller.
->In case of c4iw_l2t_send() failure in send_mpa_req(), returns without
starting the timer and not changing the ep state, which is further
handled by act_establish()
-> In act_establish()?if send_mpa_request's get_skb returns an error,
may cause an ep leak. So handle return value of send_mpa_req()
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
->Stop the ep timer after MPA negotiation so that the arp failures
during send_mpa_reply/reject will be handled by process_timeout() after
the ep timer expires.
->Added case MPA_REP_SENT in process_timeout().
->For MPA reject, c4iw_ep_disconnect tries to start an already started
timer, which leads to warning message "timer already started".
-> In case of mpa reject stop the timer and call send_mpa_reject().
-> Added new ep flag STOP_MPA_TIMER to tell fw4_ack() to stop the timer
only for send_mpa_reply(), which is set in c4iw_accept_cr().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In case of incomplete mpa messages we should not stop timer as it
results in return with timeout for the next mpa message
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
-> On passive side of connection parent_ep referenced during connection
request has to be dereferenced during the passive accept failure.
-> As passive accept failure error handlinglogic runs in atomic context,
the parent ep is dereferenced by scheduling work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FID value in a ULP_MEMIO command needs to be set to an IQ ID of
a queue configured for our PF. The FID/IQ id is used to index into the
PCIE FID table, to find out on which function the DMA needs to be
issued. Essentially, every DMA needs to have the ingress queue. The exact
ingress queue doesn't matter, but it needs to be an ingress queue
associated with the function you want to see the DMA on.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- add EP_DISC_FAIL history bit
- add QP_REFED/DEREFED history bits
- Add functions to ref/deref the cm_id and add history bit for the same
- add CLOSE_CON_RPL history
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The SRP initiator allows to set max_sectors to a value that exceeds
the largest amount of data that can be mapped at once with an mlx4
HCA using fast registration and a page size of 4 KB. Hence modify
ib_map_mr_sg() such that it can map partial sg-elements. If an
sg-element has been mapped partially, let the caller know
which fraction has been mapped by adjusting *sg_offset.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-05
This series contains updates to i40e and i40evf.
The theme behind this series is code reduction, yeah! Jesse provides
most of the changes starting with a refactor of the interpretation of
a tunnel which lets us start using the hardware's parsing. Removed
the packet split receive routine and ancillary code in preparation
for the Rx-refactor. The refactor of the receive routine,
aligns the receive routine with the one in ixgbe which was highly
optimized. The hardware supports a 16 byte descriptor for receive,
but the driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole lot
of complexity while getting rid of the code. Fixed a bug where while
changing the number of descriptors using ethtool, the driver did not
test the limits of the system memory before permanently assuming it
would be able to get receive buffer memory.
Mitch fixes a memory leak of one page each time the driver is opened by
allocating the correct number of receive buffers and do not fiddle with
next_to_use in the VF driver.
Arnd Bergmann fixed a indentation issue by adding the appropriate
curly braces in i40e_vc_config_promiscuous_mode_msg().
Julia Lawall fixed an issue found by Coccinelle, where i40e_client_ops
structure can be const since it is never modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory. On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent. Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent(). Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).
The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.
Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reported-by: David Daney <david.daney@cavium.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
This is the last user of abort_connection(), so remove it too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we fail to initiate a close operation, then
move the qp to ERROR to disassociate the ep from the qp. Failure to do
this will leak the ep resources.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead return whether the caller needs to disconnect. This is part of
getting rid of abort_connection() altogether so we properly clean up on
send_abort() failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead, have the caller, rx_data() handle the close/abort like
it does for process_mpa_request(). This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected
streaming data, we call c4iw_modify_rc_qp() and move the qp from
RTS -> TERMINATE. In c4iw_modify_rc_qp(), if rdma_fini() returns
an error, the ep will be dereferenced (refcnt=1). Then rx_data()
calls c4iw_ep_disconnect() which starts the close operation.
But if send_halfclose() fails in c4iw_ep_disconnect(), we will call
release_ep_resources() derefing the ep which reduces the refcnt to 0 and
and frees the ep. However we still has the ep mutex at that point, so we
have a touch-after-free bug. There is a similar issue where
peer_close() calls c4iw_ep_disconnect().
The solution is to add a reference to the ep in c4iw_ep_disconnect()
after acquiring the mutex, and release it after releasing the mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we start the ep timer to begin a close,
but send_halfclose() fails, we need to stop the timer and send a CLOSE
event up to the IWCM before releasing the resources. Otherwise, we can
crash when the ep timer fires if the ep is referencing a previous instance
of the device. This can happen as part of adapter reset/recovery, for
instance.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid
will be stuck in SYN_PEND and never released. So create an arp failure
handler specifically for this message to release the endpoint resources.
In pass_accept_rpl_arp_failure(), put the parent endpoint so it will
be freed when destroyed. Also we don't need to call release_tid() here
because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the
hwtid.
If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the
peer's ACK to our SYN is never received), then put the parent as well
in peer_abort().
Treat accept_cr() failures just like arp failures: put the parent ep
and release the ep resources destroying the tid
The ARP failure handlers are called in an atomic context, so we need to
schedule some of the processing which might block. Namely _c4iw_free_ep()
which needs a mutex. So create a "special" CPL opcode and handler and
schedule it via sched() to be run by process_work() in a blockable context.
Also rework the active open arp failure handler to make use of
release_ep_resources(). This allows both the active and passive arp
failure handlers to use the same deferred cleanup function.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was requesting for a writethrough mapping. But with those
flags we will end up with an SAO mapping because we now have memory
conherence always enabled. ie, the existing mapping will end up with a
WIMG value 0b1110 which is Strong Access Order.
Update this to use cache inhibitted guarded mapping.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- A number of collected fixes for oopses, memory corruptions, deadlocks,
etc. All of these fixes are small (many only 5-10 lines), obvious,
and tested.
- Fix for the security issue related to the use of write for
bi-directional communications.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MFdC
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Final set of -rc fixes for 4.6.
I've collected up a number of patches that are all pretty small with
the exception of only a couple. The hfi1 driver has a number of
important patches, and it is what really drives the line count of this
pull request up. These are all small and I've got this kernel built
and running in the test lab (I have most of the hardware, I think nes
is the only thing in this patch set that I can't say I've personally
tested and have up and running).
Summary:
- A number of collected fixes for oopses, memory corruptions,
deadlocks, etc. All of these fixes are small (many only 5-10
lines), obvious, and tested.
- Fix for the security issue related to the use of write for
bi-directional communications"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/nes: don't leak skb if carrier down
IB/security: Restrict use of the write() interface
IB/hfi1: Use kernel default llseek for ui device
IB/hfi1: Don't attempt to free resources if initialization failed
IB/hfi1: Fix missing lock/unlock in verbs drain callback
IB/rdmavt: Fix send scheduling
IB/hfi1: Prevent unpinning of wrong pages
IB/hfi1: Fix deadlock caused by locking with wrong scope
IB/hfi1: Prevent NULL pointer deferences in caching code
MAINTAINERS: Update iser/isert maintainer contact info
IB/mlx5: Expose correct max_sge_rd limit
RDMA/iw_cxgb4: Fix bar2 virt addr calculation for T4 chips
iw_cxgb4: handle draining an idle qp
iw_cxgb3: initialize ibdev.iwcm->ifname for port mapping
iw_cxgb4: initialize ibdev.iwcm->ifname for port mapping
IB/core: Don't drain non-existent rq queue-pair
IB/core: Fix oops in ib_cache_gid_set_default_gid
Currently, consumers of the flow steering infrastructure can't
choose their own flow table levels and are limited to one
flow table per level. This just waste levels.
Instead, we introduce here the possibility to use multiple
flow tables in a level. The user is free to connect these
flow tables, while following the rule (FTEs in FT of level x
could only point to FTs of level y where y > x).
In addition this patch switch the order of the create/destroy
flow tables of the NIC(vlan and main).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
