The Boot and Power Management Processor (BPMP) is a co-processor found
in Tegra SoCs. It is designed to handle the early stages of the boot
process as well as to offload power management tasks (such as clocks,
resets, powergates, ...).
The binding document defines the resources that are used by the BPMP
firmware, which implements the interprocessor communication (IPC)
between the CPU and the BPMP.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds sysfs "role" for usb role swap. This parameter can be
read and write. If you use this file as the following, you can swap
the usb role.
For example:
1) Connect a usb cable using 2 Salvator-x boards
2) On A-Device (ID pin is low), you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee080200.usb-phy/role
3) On B-Device (ID pin is high), you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-device acts as a peripheral and the B-device acts as a host.
Please note that A-Device must input the following command if you
want the board to act as a host again. (even if you disconnect the usb
cable, since id state may be the same, the A-Device keeps to act as
peripheral.)
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The corresponding driver only supports the USB PHY on Meson8b and GXBB
SoCs. Newer SoC versions are using a different USB PHY implementation,
which will mean that a new driver is required. Thus make sure that our
naming is specific enough so it does not conflict with upcoming drivers.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Update the example so the node name uses a dash (instead of an
underscore) as per convention.
Additionally it updates the example register offset to a real example
(the old value was taken from a draft where there was an additional PHY
bus).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for the "amcc,usb-otg" device
which is found in the PowerPC Canyonlands' dts.
The device definition was added by:
commit c89b3458d8 ("powerpc/44x: Add USB DWC DTS entry to Canyonlands
board")
but without any driver support as the dwc2 driver wasn't available at
that time.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a really big pile of additional connector properties, a lot of
them standardized. But they're all for specific outputs (panels, TV,
scaling, ...) so I left them out for now since this is enough for a
start.
I typed this to give Manasi a place to add her new link status
property documentation.
v2: forgot to git add all the bits (Manasi).
v3: Be more epxlicit about integrated tiled panels (Archit)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117085648.26646-1-daniel.vetter@ffwll.ch
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wFjD
-----END PGP SIGNATURE-----
Merge tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
- Add bindings for mtk-scpsys for mt2701
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
* tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt2701: Use real clock for UARTs
arm: dts: mt2701: Add clock controller device nodes
arm64: dts: mt8173: Fix auxadc node
soc: mediatek: Add MT2701 power dt-bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
support for LCD found on DaVinci DA8xx devices.
They allow configuration of memory interface and
bus priorities on the SoC to allow sufficient
bandwidth for the LCD and prevent underruns.
The DT bindings have been reviewed by Rob and
patches have been reviewed by Kevin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ye/f
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.10/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
This pull request adds two new drivers for better
support for LCD found on DaVinci DA8xx devices.
They allow configuration of memory interface and
bus priorities on the SoC to allow sufficient
bandwidth for the LCD and prevent underruns.
The DT bindings have been reviewed by Rob and
patches have been reviewed by Kevin.
* tag 'davinci-for-v4.10/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
bus: davinci: add support for da8xx bus master priority control
memory: davinci: add support for da8xx DDR2/mDDR controller
Signed-off-by: Olof Johansson <olof@lixom.net>
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzRqEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYE8HAgA
hFPUM6OmYsP81xJ8B8NscxZXi0r5ZTp14ouF5cREPF5mwXghrE5ZEGC/+xQJ/X4p
WSSGglNEJV5Ofs869wYDU3yZwNRzwkK7bGY+Mzq8eySYzkfZR2VZUf5ZStsLfUS1
j6Gr7jr2gwFtpjlwLmaUj8O4i/I3FfTiDLobqdpXoeoRcisLXS4/xDxEC1143TDR
ctylpGFEW/LXC1L4kTyLUZ6688654IC5qZBp4yHLIgb+qfd8k+CEjEyxtCzGpAQJ
sLQnsjjer4C3MqgOSDAjyguKpePCz0VIoE8wct136sQh20isbgWuhQjQ9+QzAaE+
/N+j0d87kaHUdPa097wQkg==
=LC5U
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
64bit devicetree changes including the px5 evaluation board
a fix for wrong i2c registers on rk3368 a new nvmem cell and
power-domain on rk3399 as well as moving mmc frequency
properties to the more generic max-frequency one.
* tag 'v4.10-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
arm64: dts: rockchip: add cpu-id nvmem cell node for rk3399
arm64: dts: rockchip: add sdmmc support for px5-evb
arm64: dts: rockchip: Add more properties for emmc on px5-evb
arm64: dts: rockchip: Add PX5 Evaluation board
arm64: dts: rockchip: add powerdomain for typec on rk3399
arm64: dts: rockchip: fix i2c resource error of rk3368
Signed-off-by: Olof Johansson <olof@lixom.net>
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzNfEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGsQQf/
WWYA4/oR4pT8HMns5coctc2zOyNU8KYmaeRl7TViUna+HA6/m2SGMqomTFV2AK0v
Ha3M6A35dDUGJNmAbEB5oolGOwHh82gZKYxYIQiNX+zCxeb5JxKCXWSqAjC9Ndwu
h600H1K/Qb26OzaVE/ICtlveduN+9BWrlzNseHsm99Z93FNsRLN0Z8s2Mn3jra6P
2Pf1sJkOPuh47i/Y/gTDVcFSf6Srb4SM/26fiZjrRa8LaaO/0I2Ku34ne9FygGzi
0GBHWh2SILM297MZMcrCDoJvTTqLT05tUrX1PDGmdunqP8vnsOAgvL9291G8d4sw
PbYE3onlyoxHmeOSffAe5g==
=AXPK
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
32bit devicetree changes for Rockchip including removal of skeleton.dtsi
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
* tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
ARM: dts: rockchip: Set sdmmc frequency at boot time for rk3066a
ARM: dts: rockchip: use pin constants to describe gpios on Popmetal-RK3288
include: dt-bindings: Add GPIO pin index definition for rockchip pinctrl
ARM: dts: rockchip: Add rk3066 MK808 board
devicetree: Add vendor prefix for Rikomagic
ARM: dts: rockchip: initialize rk3066 PLL clock rate
clk: rockchip: Add binding ids for cpu and peri clocks on rk3066
ARM: dts: rockchip: enable HS200/DDR52 mode for emmc on rk3288-popmetal
ARM: dts: rockchip: Support UHS mode for SD card on PopMetal-RK3288 board
ARM: dts: rockchip: remove always-on and boot-on from vcc_sd for px3-evb
ARM: dts: rockchip: update compatible strings for Rockchip efuse
ARM: dts: rockchip: add rockchip PX3 Evaluation board
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3xxx boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk322x boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3036 boards
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3xxx.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3288.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk322x.dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This was documented in the original commit, 64f1c21e86, but it
never made it into the proper location for queue sysfs files.
Signed-off-by: Jens Axboe <axboe@fb.com>
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zbqq
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Finally, I am really pleased to announce adding support for Exynos5433 ARMv8
SoC along with two boards. A lot of Samsung people contributed into this
but the final work and commits were done by Chanwoo Choi.
This means that for v4.10 we got:
1. Exynos5433 DTSI.
2. Two boards: TM2 and TM2E. These are (almost fully) working mobile phones.
* tag 'samsung-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add dts file for Exynos5433-based TM2E board
arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board
arm64: dts: exynos: Add dtsi files for Samsung Exynos5433 64bit SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qzwE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.10:
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
* tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add SCU device node to exynos4.dtsi
ARM: dts: exynos: Remove exynos4415.dtsi
ARM: dts: exynos: Document eMMC/SD/SDIO devices in Snow and Peach boards
ARM: dts: exynos: Add TOPEET itop elite based board
ARM: dts: exynos: Add TOPEET itop core board SCP package version
ARM: dts: exynos: Add entries for sound support on Odroid-XU board
ARM: dts: exynos: Remove "simple-bus" compatible from fimc-is node
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt64
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
Enhancements:
* Basic support for r8a7743 SoC; only SoC code so far
* Select errata 798181 for SoCs with CA15 cores
Clean-up:
* Consolidate R8A7743 and R8A779[234] machine definitions
Documentation:
* Add Marzen, Gose and Alt board part numbers to DT bindings
* Document SK-RZG1M board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CqVV
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Updates for v4.10
Enhancements:
* Basic support for r8a7743 SoC; only SoC code so far
* Select errata 798181 for SoCs with CA15 cores
Clean-up:
* Consolidate R8A7743 and R8A779[234] machine definitions
Documentation:
* Add Marzen, Gose and Alt board part numbers to DT bindings
* Document SK-RZG1M board
* tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779/marzen: Add board part number to DT bindings
ARM: shmobile: select errata 798181 for SoCs with CA15 cores
ARM: shmobile: Consolidate R8A7743 and R8A779[234] machine definitions
ARM: shmobile: r8a7793/gose: Add board part number to DT bindings
ARM: shmobile: r8a7794/alt: Add board part number to DT bindings
ARM: shmobile: document SK-RZG1M board
ARM: shmobile: r8a7743: basic SoC support
ARM: shmobile: only call rcar_gen2_clocks_init() if present
ARM: shmobile: Sort Kconfig selections
Signed-off-by: Olof Johansson <olof@lixom.net>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----
iQIuBAABCAAYBQJYKlYvERx0b255QGF0b21pZGUuY29tAAoJEBvUPslcq6VzT50Q
AJEsYX1dYwMyVeditzSWb65ajT53uhxPw51vIfA/bV3FUsMTaD5aZ9fsxYMt/3Eo
ayEzDFM74FM9nMGB4gXW4wryta4r5NT/lBg6vvwJfivVjTUkhQUKmH6C94dg3t2d
bHr9isM7ONJ5wxx02olg9vHyNXXgWEwPLhWKtxZKanKpoxKJajSA5dJuZR9T39X5
ZuhPFFmpMEh+IsnqYs4C1+215cFkRf21aEhMqwKRySTcHf35zitPfiuYF4Gft6Vb
Cor9JXlZGUN+dfhG48qcn+1NBEgha5r7JT2u7w+dPCXKvEn6OmpyAziUT3CYHMAc
IGeZLmBznhSZhJUvYjBmiy88YLORpWvPuGCE19AKJoi+VOGv8bSc2bnp+JCw+Ven
DB0GDWJgI2FVPNrRrLRW+dOdKwH/R8b9vE3ZtVHK8x7vowViDoGyFpndv30sL0HA
ssRvC24wAyRAcpXtAqQrFc2I8BMLzVsLzHLHriR9EnhMAspk4IJV5zkFv52ZtlxO
N6NabaD7se2ww7q3MSGuIe3+u9u3KcfKf1dsaq/E8cWFxvcJ07xnCCCYJ8DlGmZh
mS+Fkbof7NO0gbSiapzgjVtb+sfrkKqYTiIMldTzIGzmEcpK6SKXC6mAcrFAPojK
ecBq9BrLuAte4u6W1ohQoAW6rwjfz6yrAqIdzhzufGsN
=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
The Aspeed SoCs have two BT interfaces : one is IPMI compliant and the
other is H8S/2168 compliant.
The current ipmi/bt-bmc driver implements the IPMI version and we
should reflect its nature in the compatible node name using
'aspeed,ast2400-ibt-bmc' instead of 'aspeed,ast2400-bt-bmc'. The
latter should be used for a H8S interface driver if it is implemented
one day.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the following outbound related device tree properties:
brcm,pcie-ob-window-size
brcm,pcie-ob-oarr-size
The above two properties are a bit duplicated in functions. In addition,
the next generation iProc PCIe controller has outbound mapping window that
supports more than just two sizes, which cannot be properly supported by
these properties.
[bhelgaas: changelog]
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
(decoupled from the generic scpi binding)
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch adds specific compatible to support all the unversioned SCPI
protocols prior to v1.0 release. This will be applicable for all the
implementations using draft versions or modified versions of those
draft vesrions of SCPI protocol.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Since SCPI is a generic protocol and the bindings are intended to be
generic, we need to decouple all the platform specific binding details
out of the generic bindings.
This patch moves are the Juno platform specific details into a separate
binding document.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Sample driver creates mdev device that simulates serial port over PCI
card.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Signed-off-by: Neo Jia <cjia@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Audio block requires access to two parent clocks: audio PLL and oscillator,
so add this information to device tree bindings documentation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The proper parent clock for FSYS block is "aclk_fsys_200"
according to the Exynos5433 reference manual.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The SVG files are larger than the draw dimentions, have long
lines and aren't cleaned. Use inkscape to automatically fix
those issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Somehow, two DVB headers were included twice. Remove the
duplication
Reported-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some dumb VGA DACs are active components which require external power.
Add support for specifying a regulator as its power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
On some tablets the touchscreen controller is powered by separate
regulators, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Per the original author, the proposed document was never deemed
necessary, and the important bits got merged into completion.txt. Let's
just stop confusing readers by pointing at a nonexistent doc.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a conversion of the USB documentation to the Sphinx format.
No content was altered or reformatted.
Signed-off-by: Oliver <oneukum@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
While the {READ,WRITE}_ONCE() macros should be used in preference to
ACCESS_ONCE(), the circular buffer documentation uses the latter
exclusively.
To point people in the right direction, and as a step towards the
eventual removal of ACCESS_ONCE(), update the documentation to use
READ_ONCE(), as ACCESS_ONCE() is only used in a reader context in the
circular buffer documentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
While the {READ,WRITE}_ONCE() macros should be used in preference to
ACCESS_ONCE(), the atomic documentation uses the latter exclusively.
To point people in the right direction, and as a step towards the
eventual removal of ACCESS_ONCE(), update the documentation to use the
{READ,WRITE}_ONCE() macros as appropriate.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Recent Makefile changes added an rm command without the requisite "-f",
leading to warnings if the files do not exist. Make it be quiet again.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The PDF files that contain media images were actually generated
offline from their SVG or PNG source files.
Sphinx can handle PNG sources automatially. So, let's just
drop their PDF counterparts.
For SVG, however, Sphinx doesn't produce the right tags to
use the TexLive SVG support. Also, the SVG support is done via
shell execution, with is not nice.
So, while we don't have any support for SVG inside Sphinx
core or as an extension, move the logic to build them to Makefile,
producing the PDF images on runtime.
NOTE: due to the way Sphinx works, the PDF images should be
generated inside the Kernel source tree, as otherwise Sphinx
won't find it, not obeying what's specified by "O=" makefile
parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Right now, media is using two different formats for bitmap
images: GIF and PNG. Let's use just one, to make it simpler when
building with Sphinx.
As PNG is usually better than GIF, let's use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
SVG images are nicer, as they can easily be scaled. Also, they're
written in text, with makes easier to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are several missing columns on the size specification,
causing LaTeX to complain on interactive mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
adjustbox doesn't work on longtables. Also, this
causes an error on LaTeX in interactive mode.
So, use, instead, a tiny font.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
PDF build on Kernel 4.9-rc? returns an error with Sphinx 1.3.x
and Sphinx 1.4.x, when trying to solve some cross-references.
The solution is to redefine the \DURole macro.
However, this is redefined too late. Move such redefinition to
LaTeX preamble and bind it to just the Sphinx versions where the
error is known to be present.
Tested by building the documentation on interactive mode:
make PDFLATEX=xelatex -C Documentation/output/./latex
Fixes: e61a39baf7 ("[media] index.rst: Fix LaTeX error in interactive mode on Sphinx 1.4.x")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Another pile of misc:
- Explicit fencing for atomic! Big thanks to Gustavo, Sean, Rob 3x, Brian
and anyone else I've forgotten to make this happen.
- roll out fbdev helper ops to drivers (Stefan Christ)
- last bits of drm_crtc split-up&kerneldoc
- some drm_irq.c crtc functions cleanup
- prepare_fb helper for cma, works correctly with explicit fencing (Marek
Vasut)
- misc small patches all over
* tag 'drm-misc-next-2016-11-16' of git://anongit.freedesktop.org/git/drm-misc: (51 commits)
drm/fence: add out-fences support
drm/fence: add fence timeline to drm_crtc
drm/fence: add in-fences support
drm/bridge: analogix_dp: return error if transfer none byte
drm: drm_irq.h header cleanup
drm/irq: Unexport drm_vblank_on/off
drm/irq: Unexport drm_vblank_count
drm/irq: Make drm_vblank_pre/post_modeset internal
drm/nouveau: Use drm_crtc_vblank_off/on
drm/amdgpu: Use drm_crtc_vblank_on/off for dce6
drm/color: document NULL values and default settings better
drm: Drop externs from drm_crtc.h
drm: Move tile group code into drm_connector.c
drm: Extract drm_mode_config.[hc]
Revert "drm: Add aspect ratio parsing in DRM layer"
Revert "drm: Add and handle new aspect ratios in DRM layer"
drm/print: Move kerneldoc next to definition
drm: Consolidate dumb buffer docs
drm: Clean up kerneldoc for struct drm_driver
drm: Extract drm_drv.h
...
The usual patches from us, but most notably the introduction of the A64
clocks unit.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYK30lAAoJEBx+YmzsjxAgNqMP/A0eKZkzCWP8QXePS5OVTzjn
Afnp85tpYGNrR5OTwJiM32IDAAU6mvb4813Z0MwQ5Wp+TM3APpiRzwnF3yjxeoGu
Jgzsu+NLgPtp/CozaGC46IlacGRR0amyLhryq8cVOaEKTed4b0t2Xjmk4JsRj7Gp
2ki5HVs4QSN63p4GixxhxVXgtYNoOBvm3qCgMbWa10j5DIDA2Wf//feudTeu98xa
gR9uz08xBVHXtIlyjXfY72l/qcjmcRZDdAXPTItZWR4MREuLMh3jlwM2oxMn1nKY
PLu7KfPail1ATv+6Pa5EJcAqvxCnW8mH8F0Tk/xqd/ZGuEwHW5rRPVl5NLO81iBe
K4Pfh8DrEtMBhS2C5nY3qOYQP6XcE4d2OSN8zNCM50ATdXMx+6gX1Dep6cz6waKj
Uo/v6GdkMhKgd1lBcH2CGJrWN7HQWb4wM/gctIa7T5uIQp/WBWEXACpOmRsD+4yt
c83qtys3FTO5Iuj1UVETHm8tAIC58xvQ+ZYs3Z7wusMJVRMH2KMi7MiNXF0zBHDL
cG/cQa9MrhIOJgd04TC8EDye/+Wn1rLFhMZWnbgcThpdKmd+MSPO/3ZeNKkCFJAh
F3CD+5oeQA9mctJBirpsPCrGnKwtkEZycB7jymkEPptvad+TLfGHdkwE0U2FhaxE
qN094vyPeAgceu9u9NyZ
=7+Az
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock changes from Maxime Ripard:
The usual patches from us, but most notably the introduction of the A64
clocks unit.
* tag 'sunxi-clk-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: sun8i-h3: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: sun8i-a23: Set CLK_SET_RATE_PARENT for audio module clocks
clk: sunxi-ng: Add A64 clocks
clk: sunxi-ng: Implement minimum for multipliers
clk: sunxi-ng: Add minimums for all the relevant structures and clocks
clk: sunxi-ng: Finish to convert to structures for arguments
clk: sunxi-ng: Remove the use of rational computations
clk: sunxi-ng: Rename the internal structures
clk: sunxi: mod0: improve function-level documentation
This patch adds support for Exynos5433 specific version of the GScaler
module. The main difference between Exynos 5433 and earlier is addition
of new clocks that have to be controlled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FDP1 is a de-interlacing module which converts interlaced video to
progressive video. It is also capable of performing pixel format conversion
between YCbCr/YUV formats and RGB formats.
Signed-off-by: Kieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The menu control selects the operation mode of a video deinterlacer. The
menu entries are driver specific.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran@bingham.xyz>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_LOG_ADDRS_FL_CDC_ONLY flag is missing at the documentation,
causing this warning:
Documentation/output/cec.h.rst:6: WARNING: undefined label: cec-log-addrs-fl-cdc-only (if the link has no caption the label must precede a section header)
Add a documentation for it, based on the commit that introduced the
flag.
Fixes: a69a168a1b ("[media] cec: add proper support for CDC-Only CEC devices")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last open issues have been addressed, so it is time to move
this out of staging and into the mainline and to move the public
cec headers to include/uapi/linux.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_MSG_INITIATE_ARC message is special since it is the ONLY
CEC message that accepts two possible valid replies:
CEC_MSG_REPORT_ARC_INITIATED and CEC_MSG_REPORT_ARC_TERMINATED.
So if the transmitted message is CEC_MSG_INITIATE_ARC and the remote
side replied with CEC_MSG_REPORT_ARC_INITIATED or CEC_MSG_REPORT_ARC_TERMINATED,
then a msg->reply value of CEC_MSG_REPORT_ARC_INITIATED or
CEC_MSG_REPORT_ARC_TERMINATED will match either reply.
I thought about either adding a second reply2 field, but that's ugly
for all other messages that have only one reply, and what if in the
future a new message is added that can have three replies?
Another option would be to add a cec_msg flag, but really, the combination
of CEC_MSG_REPORT_ARC_INITIATED and a reply value of one of the two
possible replies already functions as a flag.
Another advantage of this approach is that it is safe to re-use a
cec_msg struct. No need to zero a flags field or a reply2 field.
So since this really is an exception in the CEC specification, I
decided to implement it as an exception as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Give the caller more control over how replies to a transmit are
handled. By default the reply will only go to the filehandle that
called CEC_TRANSMIT. If this new flag is set, then the reply will
also go to all followers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
By default the CEC_MSG_USER_CONTROL_PRESSED/RELEASED messages
are passed on to the follower(s) only. If the new
CEC_LOG_ADDRS_FL_ALLOW_RC_PASSTHRU flag is set in the
flags field of struct cec_log_addrs then these messages are also
passed on to the remote control input subsystem and they will appear
as keystrokes.
This used to be the default behavior, but now you have to explicitly
enable it. This is done to force the caller to think about possible
security issues (e.g. if these messages are used to enter passwords).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This uses Laurent's python script to convert all tables, dropping
the useless 'row' comments.
See commit c2b66cafdf ("[media] v4l: doc: Remove row numbers from tables")
for the script that was used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code examples on how to enumerate controls were really long in the
tooth. Update them.
Using FLAG_NEXT_CTRL is preferred these days, so give that example first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Improve the internal CEC documentation. In particular add a section
that specifies that transmit-related interrupts should be processed
before receive interrupts.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Includes Peter Rosin's interesting drivers for a comparator. First complex
use we have had with an analog front end made from discrete components.
Brian Masney's work on moving the tsl2583 driver out of staging also
feature extensively!
New Drivers
* DAC based on a digital potentiometer
- New driver for the use of a dpot as a DAC. Includes bindings and Axentia
entry in vendor prefixes.
* Envelope detector baed on DAC and a comparator including device tree
bindings.
Staging Graduation
* tsl2583.
Core new features
- Core provision for _available attributes. This one had been stalled for
a long time until Peter picked it up and ran with it!
- In kernel interface helpers to retrieve available info from channels.
Driver new features
* mcp4531
- Add range of available raw values (used for the dpot dac driver).
Driver cleanups and fixes for issues introduced
* ad7766
- Testing the wrong variable following devm_regulator_bulk_get introduced
with the driver earlier in this cycle.
* ad9832
- Fix a wrong ordering in the probe introduced in the previous set of
patches. A use before allocation bug.
* cros_ec_sensors
- Testing for an error in a u8 will never work.
* mpu3050
- Remove duplicate initializer for the module owner.
- Add missing i2c dependency.
- Inform the i2c mux core how it is used - step one in implifying device
tree bindings.
* st-sensors
- Get rid of large number of uninformative defines in favour of putting the
constants where they are relevant. It is clear what they are from where
they are used.
* tsl2583
- Fix unused function warning when CONFIG_PM disabled and remove the
ifdefs in favour of __maybe_unused.
- Refactor taos_chip_on to only read relevant registers.
- Make sure calibscale and integration time are being set.
- Verify chip is in ready to be used before calibration.
- Remove some repeated checks for chip status (it's protected by a mutex
so can't change until it's released)
- Change current state storage from a tristate enum to a boolean seeing as
only two values are actually used now.
- Drop a redundant write to the control regiser in taos_probe (it's a noop)
- Drop the FSF mailing address.
- Clean up logging to not use hard coded function names (use __func__
instead).
- Cleanup up variable and function name prefixes.
- Alignment of #define fixes.
- Fix comparison between signed and unsigned integer warnings.
- Add some newlines in favour of readability.
- Combine the two sysfs ABI docs that somehow ended up in different places.
- Fix multiline comment syntax.
- Move a code block to inside an else statement as it makes more sense there.
- Change tsl2583_als_calibrate to return 0 rather than a value nothing
reads.
- Drop some pointless brackets
- Don't assume 32bit unsigned int.
- Change to a per device instance lux table.
- Add missing tsl2583 to the list of supported devices in the intro comments.
- Improve commment on clearing of interrupts.
- Drop some uninformative comments.
- Drop a memset call that doesn't do anything useful any more.
- Don't initialize some return variables that are always set.
- Add Brian Masney as a module author after all these changes.
-----BEGIN PGP SIGNATURE-----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=mPkb
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanup for the 4.10 cycle.
Includes Peter Rosin's interesting drivers for a comparator. First complex
use we have had with an analog front end made from discrete components.
Brian Masney's work on moving the tsl2583 driver out of staging also
feature extensively!
New Drivers
* DAC based on a digital potentiometer
- New driver for the use of a dpot as a DAC. Includes bindings and Axentia
entry in vendor prefixes.
* Envelope detector baed on DAC and a comparator including device tree
bindings.
Staging Graduation
* tsl2583.
Core new features
- Core provision for _available attributes. This one had been stalled for
a long time until Peter picked it up and ran with it!
- In kernel interface helpers to retrieve available info from channels.
Driver new features
* mcp4531
- Add range of available raw values (used for the dpot dac driver).
Driver cleanups and fixes for issues introduced
* ad7766
- Testing the wrong variable following devm_regulator_bulk_get introduced
with the driver earlier in this cycle.
* ad9832
- Fix a wrong ordering in the probe introduced in the previous set of
patches. A use before allocation bug.
* cros_ec_sensors
- Testing for an error in a u8 will never work.
* mpu3050
- Remove duplicate initializer for the module owner.
- Add missing i2c dependency.
- Inform the i2c mux core how it is used - step one in implifying device
tree bindings.
* st-sensors
- Get rid of large number of uninformative defines in favour of putting the
constants where they are relevant. It is clear what they are from where
they are used.
* tsl2583
- Fix unused function warning when CONFIG_PM disabled and remove the
ifdefs in favour of __maybe_unused.
- Refactor taos_chip_on to only read relevant registers.
- Make sure calibscale and integration time are being set.
- Verify chip is in ready to be used before calibration.
- Remove some repeated checks for chip status (it's protected by a mutex
so can't change until it's released)
- Change current state storage from a tristate enum to a boolean seeing as
only two values are actually used now.
- Drop a redundant write to the control regiser in taos_probe (it's a noop)
- Drop the FSF mailing address.
- Clean up logging to not use hard coded function names (use __func__
instead).
- Cleanup up variable and function name prefixes.
- Alignment of #define fixes.
- Fix comparison between signed and unsigned integer warnings.
- Add some newlines in favour of readability.
- Combine the two sysfs ABI docs that somehow ended up in different places.
- Fix multiline comment syntax.
- Move a code block to inside an else statement as it makes more sense there.
- Change tsl2583_als_calibrate to return 0 rather than a value nothing
reads.
- Drop some pointless brackets
- Don't assume 32bit unsigned int.
- Change to a per device instance lux table.
- Add missing tsl2583 to the list of supported devices in the intro comments.
- Improve commment on clearing of interrupts.
- Drop some uninformative comments.
- Drop a memset call that doesn't do anything useful any more.
- Don't initialize some return variables that are always set.
- Add Brian Masney as a module author after all these changes.
Memory-to-memory V4L2 devices all have file handle specific context.
Say this in the API documentation so that the user space may rely on it
being the case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If CONFIG_NVM is disabled, loading null_block module with use_lightnvm=1
fails. But there are no messages and documents related to the failure.
Add the appropriate error message.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Massaged the text a bit.
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds the dt-binding documentation for the clock and reset unit
found on Rockchip rk1108 SoCs.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "imply" keyword is a weak version of "select" where the target
config symbol can still be turned off, avoiding those pitfalls that come
with the "select" keyword.
This is useful e.g. with multiple drivers that want to indicate their
ability to hook into a secondary subsystem while allowing the user to
configure that subsystem out without also having to unset these drivers.
Currently, the same effect can almost be achieved with:
config DRIVER_A
tristate
config DRIVER_B
tristate
config DRIVER_C
tristate
config DRIVER_D
tristate
[...]
config SUBSYSTEM_X
tristate
default DRIVER_A || DRIVER_B || DRIVER_C || DRIVER_D || [...]
This is unwieldy to maintain especially with a large number of drivers.
Furthermore, there is no easy way to restrict the choice for SUBSYSTEM_X
to y or n, excluding m, when some drivers are built-in. The "select"
keyword allows for excluding m, but it excludes n as well. Hence
this "imply" keyword. The above becomes:
config DRIVER_A
tristate
imply SUBSYSTEM_X
config DRIVER_B
tristate
imply SUBSYSTEM_X
[...]
config SUBSYSTEM_X
tristate
This is much cleaner, and way more flexible than "select". SUBSYSTEM_X
can still be configured out, and it can be set as a module when none of
the drivers are configured in or all of them are modular.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Cc: Edward Cree <ecree@solarflare.com>
Link: http://lkml.kernel.org/r/1478841010-28605-2-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce managed counterparts for alloc_percpu() and free_percpu().
Add devm_alloc_percpu() and devm_free_percpu() into the managed
interfaces list.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This document defines the binding for a component that loads firmware
and control the life cycle of the Qualcomm ADSP Hexagon core.
Acked-by: Rob Herring <robh@kernel.org>
Cc: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If the RAMOOPS_FLAG_FTRACE_PER_CPU flag is passed to ramoops pdata, split
the ftrace space into multiple zones depending on the number of CPUs.
This speeds up the performance of function tracing by about 280% in my
tests as we avoid the locking. The trade off being lesser space available
per CPU. Let the ramoops user decide which option they want based on pdata
flag.
Signed-off-by: Joel Fernandes <joelaf@google.com>
[kees: added max_ftrace_cnt to track size, added DT logic and docs]
Signed-off-by: Kees Cook <keescook@chromium.org>
Support for the Allwinner A31 SoC display engine using the sun4i-drm
driver.
-----BEGIN PGP SIGNATURE-----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=fERq
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-next
sun4i-drm changes for 4.10
Support for the Allwinner A31 SoC display engine using the sun4i-drm
driver.
* tag 'sunxi-drm-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drm/sun4i: Add a few formats
drm/sun4i: Add compatible strings for A31/A31s display pipelines
drm/sun4i: Add compatible string for A31/A31s TCON (timing controller)
drm/sun4i: tcon: Move SoC specific quirks to a DT matched data structure
drm/sun4i: sun6i-drc: Support DRC on A31 and A31s
A new file is created:
/sys/kernel/debug/tracing/trace_marker_raw
This allows for appications to create data structures and write the binary
data directly into it, and then read the trace data out from trace_pipe_raw
into the same type of data structure. This saves on converting numbers into
ASCII that would be required by trace_marker.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Document the devicetree bindings for the Generic Memory Interface (GMI)
bus driver found on Tegra SOCs.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Udoo (http://www.udoo.org/) manufactures development boards based on
i.MX and x86.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a vendor prefix for Samtec, a Softing company.
http://www.samtec.dehttp://www.samtec.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a vendor prefix for the Macnica company.
http://http://www.macnica.com
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Add vendor prefix for Aries Embedded GmbH
http://www.aries-embedded.de/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
Hence remove it from the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add documentation how devicetree can be used to configure ath9k based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add DT binding for the Hardware Synchronization Primitives (HSP). The
HSP is designed for the processors to share resources and communicate
with one another. A set of hardware synchronization primitives for
interprocessor communication (IPC) is provided. IPC protocols can use
use these hardware synchronization primitives when operating between
processors in an AMP configuration.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
And also put the overview section into the KMS Properties part of the
docs, instead of randomly-placed within the helpers - this is part of
the uabi.
With this patch I think drm_crtc.[hc] is cleaned up and entirely
documented.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
And shuffle the kernel-doc structure a bit since drm_crtc.[hc] now
only contains CRTC-related functions and structures.
v2:
- rebase onto drm-misc
- don't forget to move drm_mode_config_cleanup.
- move 2 internal decls under the right heading (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
kerneldoc expects the comment next to definitions, otherwise it can't
pick up exported vs. internal stuff.
This fixes a warning from the doc build done with:
$ make DOCBOOKS="" htmldocs
Fixes: d8187177b0 ("drm: add helper for printing to log or seq_file")
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161114115825.22050-8-daniel.vetter@ffwll.ch
Would be great if everony could add
$ make DOCBOOKS="" htmldocs
to their build scripts to catch these. 0day should also report them,
not sure why it failed to spot this.
Fixes: f54d186700 ("dma-buf: Rename struct fence to dma_fence")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161114115825.22050-4-daniel.vetter@ffwll.ch
Would be great if everony could add
$ make DOCBOOKS="" htmldocs
to their build scripts to catch these. 0day should also report them,
not sure why it failed to spot this.
Fixes: b42fe9ca0a ("drm/i915: Split out i915_vma.c")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161114115825.22050-3-daniel.vetter@ffwll.ch
This patch adds documentation for the devicetree bindings used by
the DT files of Hisilicon Hip07 D05 board.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Document the SK-RZG1E device tree bindings, listing it as a supported board.
This allows to use checkpatch.pl to validate .dts files referring to the
SK-RZG1E board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the dt-binding documentation for rk1108 pinctrl
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add minimal support for the RZ/G1E (R8A7745) SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The pin controller found in the Allwinner SoCs has support for interrupts
debouncing.
However, this is not done per-pin, preventing us from using the generic
pinconf binding for that, but per irq bank, which, depending on the SoC,
ranges from one to five.
Introduce a device-wide property to deal with this using a microsecond
resolution. We can re-use the per-pin input-debounce property for that, so
let's do it!
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add the support of GPF[1-5] pin of Exynos5433 SoC. The GPFx need
to support the multiple memory map because the registers of GPFx are located
in the different domain.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the associated smd edge to be described within the wcnss
remoteproc node. This creates a bond between the remoteproc and the
associated smd channels and devices, showing the interaction between the
two parts and provides both a natural reference to the other.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Document the R8A7796-specific DT bindings and support them in the
driver. The HDMI output is currently not supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add support for the R8A7792 DU; it has 2 DPAD (RGB) outputs.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Add "rockchip,rk1108-dw-mshc", "rockchip,rk3288-dw-mshc" for
dwmmc on rk1108 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull networking fixes from David Miller:
1) Fix off by one wrt. indexing when dumping /proc/net/route entries,
from Alexander Duyck.
2) Fix lockdep splats in iwlwifi, from Johannes Berg.
3) Cure panic when inserting certain netfilter rules when NFT_SET_HASH
is disabled, from Liping Zhang.
4) Memory leak when nft_expr_clone() fails, also from Liping Zhang.
5) Disable UFO when path will apply IPSEC tranformations, from Jakub
Sitnicki.
6) Don't bogusly double cwnd in dctcp module, from Florian Westphal.
7) skb_checksum_help() should never actually use the value "0" for the
resulting checksum, that has a special meaning, use CSUM_MANGLED_0
instead. From Eric Dumazet.
8) Per-tx/rx queue statistic strings are wrong in qed driver, fix from
Yuval MIntz.
9) Fix SCTP reference counting of associations and transports in
sctp_diag. From Xin Long.
10) When we hit ip6tunnel_xmit() we could have come from an ipv4 path in
a previous layer or similar, so explicitly clear the ipv6 control
block in the skb. From Eli Cooper.
11) Fix bogus sleeping inside of inet_wait_for_connect(), from WANG
Cong.
12) Correct deivce ID of T6 adapter in cxgb4 driver, from Hariprasad
Shenai.
13) Fix potential access past the end of the skb page frag array in
tcp_sendmsg(). From Eric Dumazet.
14) 'skb' can legitimately be NULL in inet{,6}_exact_dif_match(). Fix
from David Ahern.
15) Don't return an error in tcp_sendmsg() if we wronte any bytes
successfully, from Eric Dumazet.
16) Extraneous unlocks in netlink_diag_dump(), we removed the locking
but forgot to purge these unlock calls. From Eric Dumazet.
17) Fix memory leak in error path of __genl_register_family(). We leak
the attrbuf, from WANG Cong.
18) cgroupstats netlink policy table is mis-sized, from WANG Cong.
19) Several XDP bug fixes in mlx5, from Saeed Mahameed.
20) Fix several device refcount leaks in network drivers, from Johan
Hovold.
21) icmp6_send() should use skb dst device not skb->dev to determine L3
routing domain. From David Ahern.
22) ip_vs_genl_family sets maxattr incorrectly, from WANG Cong.
23) We leak new macvlan port in some cases of maclan_common_netlink()
errors. Fix from Gao Feng.
24) Similar to the icmp6_send() fix, icmp_route_lookup() should
determine L3 routing domain using skb_dst(skb)->dev not skb->dev.
Also from David Ahern.
25) Several fixes for route offloading and FIB notification handling in
mlxsw driver, from Jiri Pirko.
26) Properly cap __skb_flow_dissect()'s return value, from Eric Dumazet.
27) Fix long standing regression in ipv4 redirect handling, wrt.
validating the new neighbour's reachability. From Stephen Suryaputra
Lin.
28) If sk_filter() trims the packet excessively, handle it reasonably in
tcp input instead of exploding. From Eric Dumazet.
29) Fix handling of napi hash state when copying channels in sfc driver,
from Bert Kenward.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (121 commits)
mlxsw: spectrum_router: Flush FIB tables during fini
net: stmmac: Fix lack of link transition for fixed PHYs
sctp: change sk state only when it has assocs in sctp_shutdown
bnx2: Wait for in-flight DMA to complete at probe stage
Revert "bnx2: Reset device during driver initialization"
ps3_gelic: fix spelling mistake in debug message
net: ethernet: ixp4xx_eth: fix spelling mistake in debug message
ibmvnic: Fix size of debugfs name buffer
ibmvnic: Unmap ibmvnic_statistics structure
sfc: clear napi_hash state when copying channels
mlxsw: spectrum_router: Correctly dump neighbour activity
mlxsw: spectrum: Fix refcount bug on span entries
bnxt_en: Fix VF virtual link state.
bnxt_en: Fix ring arithmetic in bnxt_setup_tc().
Revert "include/uapi/linux/atm_zatm.h: include linux/time.h"
tcp: take care of truncations done by sk_filter()
ipv4: use new_gw for redirect neigh lookup
r8152: Fix error path in open function
net: bpqether.h: remove if_ether.h guard
net: __skb_flow_dissect() must cap its return value
...
Add new compatible string "brcm,iproc-pcie-paxc-v2" to the iProc PCIe
device tree binding document. "brcm,iproc-pcie-paxc-v2" is for the second
generation of the Broadcom iProc PCIe PAXC host controller.
Update the binding document with more detailed description of each
compatible string and compatible SoCs.
Add description of optional property "msi-map", for use with MSI
controllers with sideband data.
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Use glob_match() to support flexible glob wildcards (*,?)
and character classes ([) for ftrace.
Since the full glob matching is slower than the current
partial matching routines(*pat, pat*, *pat*), this leaves
those routines and just add MATCH_GLOB for complex glob
expression.
e.g.
----
[root@localhost tracing]# echo 'sched*group' > set_ftrace_filter
[root@localhost tracing]# cat set_ftrace_filter
sched_free_group
sched_change_group
sched_create_group
sched_online_group
sched_destroy_group
sched_offline_group
[root@localhost tracing]# echo '[Ss]y[Ss]_*' > set_ftrace_filter
[root@localhost tracing]# head set_ftrace_filter
sys_arch_prctl
sys_rt_sigreturn
sys_ioperm
SyS_iopl
sys_modify_ldt
SyS_mmap
SyS_set_thread_area
SyS_get_thread_area
SyS_set_tid_address
sys_fork
----
Link: http://lkml.kernel.org/r/147566869501.29136.6462645009894738056.stgit@devbox
Acked-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some of the host drivers have the requirement of knowing whether the EP
would never train at some link speed at all. For instance, on some boards,
the link won't train at 5 GT/s but the host driver still sacrifice some
cycles to wait for the result of training at 5 GT/s as the host could
actually support 5 GT/s. So we could parse this new property and make the
host drivers be aware of these cases.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
deference should actually be dereference.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Recent memory-model work deduces the relationships of RCU read-side
critical sections and grace periods based on the relationships of
accesses within a critical section and accesses preceding and following
the grace period. This commit therefore adds this viewpoint.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Create the driver for the da8xx master peripheral priority
configuration and implement support for writing to the three
Master Priority registers on da850 SoCs.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Create a new driver for the da8xx DDR2/mDDR controller and implement
support for writing to the Peripheral Bus Burst Priority Register.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch allows to build and use vGICv3 ITS in 32-bit mode.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds support for Renesas r8a7796 SoC. This SoC is not
compatible with r8a7795 because using firmware version differs.
Since the "V2" firmware can be used on both r8a7795 (es1.x) and r8a7796,
the "renesas,rcar-gen3-xhci" keeps to use the "V2" for now.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a hardware bug, reading memory (from the Accelerator Coherency Port)
with a burst size equal to the maximum burst size allowed by the DMA
hardware's buffer size will cause a hardware hang on the ARTPEC-6 SoC,
where the only solution is a manual power cycle.
On ARTPEC-6, this hardware bug does not trigger when writing memory (to the
Accelerator Coherency Port) with a burst size equal to the maximum burst
size allowed by the DMA hardware's buffer size.
To avoid this hardware hang, introduce a new optional max-burst property
for memory reads. For completeness, also introduce a max-burst property for
memory writes.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This commit adds Korean translation of HOWTO document into rst based
documentation build system.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Few files under dma-buf/ changed their names but the changes didn't
applied to a document that referencing them. It is causing few
documentation build warnings. This commit fixes the problems by
applying changed file names on the document.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Move tsl2580, tsl2581, tsl2583 driver out of staging into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
_
| \
input +------>-------|+ \
| \
.-------. | }---.
| | | / |
| dac|-->--|- / |
| | |_/ |
| | |
| | |
| irq|------<-------'
| |
'-------'
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It is assumed that the dpot is used as a voltage divider between the
current dpot wiper setting and the maximum resistance of the dpot. The
divided voltage is provided by a vref regulator.
.------.
.-----------. | |
| vref |--' .---.
| regulator |--. | |
'-----------' | | d |
| | p |
| | o | wiper
| | t |<---------+
| | |
| '---' dac output voltage
| |
'------+------------+
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Example:
$ cat '/sys/bus/iio/devices/iio:device0/out_resistance_raw_available'
[0 1 256]
Meaning: min 0, step 1 and max 256.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Apple's EFI drivers supply device properties which are needed to support
Macs optimally. They contain vital information which cannot be obtained
any other way (e.g. Thunderbolt Device ROM). They're also used to convey
the current device state so that OS drivers can pick up where EFI
drivers left (e.g. GPU mode setting).
There's an EFI driver dubbed "AAPL,PathProperties" which implements a
per-device key/value store. Other EFI drivers populate it using a custom
protocol. The macOS bootloader /System/Library/CoreServices/boot.efi
retrieves the properties with the same protocol. The kernel extension
AppleACPIPlatform.kext subsequently merges them into the I/O Kit
registry (see ioreg(8)) where they can be queried by other kernel
extensions and user space.
This commit extends the efistub to retrieve the device properties before
ExitBootServices is called. It assigns them to devices in an fs_initcall
so that they can be queried with the API in <linux/property.h>.
Note that the device properties will only be available if the kernel is
booted with the efistub. Distros should adjust their installers to
always use the efistub on Macs. grub with the "linux" directive will not
work unless the functionality of this commit is duplicated in grub.
(The "linuxefi" directive should work but is not included upstream as of
this writing.)
The custom protocol has GUID 91BD12FE-F6C3-44FB-A5B7-5122AB303AE0 and
looks like this:
typedef struct {
unsigned long version; /* 0x10000 */
efi_status_t (*get) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_NOT_FOUND, EFI_BUFFER_TOO_SMALL */
efi_status_t (*set) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name,
IN void *property_value,
IN u32 property_value_len);
/* allocates copies of property name and value */
/* EFI_SUCCESS, EFI_OUT_OF_RESOURCES */
efi_status_t (*del) (
IN struct apple_properties_protocol *this,
IN struct efi_dev_path *device,
IN efi_char16_t *property_name);
/* EFI_SUCCESS, EFI_NOT_FOUND */
efi_status_t (*get_all) (
IN struct apple_properties_protocol *this,
OUT void *buffer,
IN OUT u32 *buffer_len);
/* EFI_SUCCESS, EFI_BUFFER_TOO_SMALL */
} apple_properties_protocol;
Thanks to Pedro Vilaça for this blog post which was helpful in reverse
engineering Apple's EFI drivers and bootloader:
https://reverse.put.as/2016/06/25/apple-efi-firmware-passwords-and-the-scbo-myth/
If someone at Apple is reading this, please note there's a memory leak
in your implementation of the del() function as the property struct is
freed but the name and value allocations are not.
Neither the macOS bootloader nor Apple's EFI drivers check the protocol
version, but we do to avoid breakage if it's ever changed. It's been the
same since at least OS X 10.6 (2009).
The get_all() function conveniently fills a buffer with all properties
in marshalled form which can be passed to the kernel as a setup_data
payload. The number of device properties is dynamic and can change
between a first invocation of get_all() (to determine the buffer size)
and a second invocation (to retrieve the actual buffer), hence the
peculiar loop which does not finish until the buffer size settles.
The macOS bootloader does the same.
The setup_data payload is later on unmarshalled in an fs_initcall. The
idea is that most buses instantiate devices in "subsys" initcall level
and drivers are usually bound to these devices in "device" initcall
level, so we assign the properties in-between, i.e. in "fs" initcall
level.
This assumes that devices to which properties pertain are instantiated
from a "subsys" initcall or earlier. That should always be the case
since on macOS, AppleACPIPlatformExpert::matchEFIDevicePath() only
supports ACPI and PCI nodes and we've fully scanned those buses during
"subsys" initcall level.
The second assumption is that properties are only needed from a "device"
initcall or later. Seems reasonable to me, but should this ever not work
out, an alternative approach would be to store the property sets e.g. in
a btree early during boot. Then whenever device_add() is called, an EFI
Device Path would have to be constructed for the newly added device,
and looked up in the btree. That way, the property set could be assigned
to the device immediately on instantiation. And this would also work for
devices instantiated in a deferred fashion. It seems like this approach
would be more complicated and require more code. That doesn't seem
justified without a specific use case.
For comparison, the strategy on macOS is to assign properties to objects
in the ACPI namespace (AppleACPIPlatformExpert::mergeEFIProperties()).
That approach is definitely wrong as it fails for devices not present in
the namespace: The NHI EFI driver supplies properties for attached
Thunderbolt devices, yet on Macs with Thunderbolt 1 only one device
level behind the host controller is described in the namespace.
Consequently macOS cannot assign properties for chained devices. With
Thunderbolt 2 they started to describe three device levels behind host
controllers in the namespace but this grossly inflates the SSDT and
still fails if the user daisy-chained more than three devices.
We copy the property names and values from the setup_data payload to
swappable virtual memory and afterwards make the payload available to
the page allocator. This is just for the sake of good housekeeping, it
wouldn't occupy a meaningful amount of physical memory (4444 bytes on my
machine). Only the payload is freed, not the setup_data header since
otherwise we'd break the list linkage and we cannot safely update the
predecessor's ->next link because there's no locking for the list.
The payload is currently not passed on to kexec'ed kernels, same for PCI
ROMs retrieved by setup_efi_pci(). This can be added later if there is
demand by amending setup_efi_state(). The payload can then no longer be
made available to the page allocator of course.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: Pierre Moreau <pierre.morrow@free.fr> [MacBookPro11,3]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pedro Vilaça <reverser@put.as>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: grub-devel@gnu.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20161112213237.8804-9-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to avoid loading
on non-toshiba systems.
Documentation/ABI:
- ibm_rtl: The "What:" fields are incomplete
toshiba-wmi:
- Fix loading the driver on non Toshiba laptops
ideapad-laptop:
- Add another DMI entry for Yoga 900
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYJSzXAAoJEKbMaAwKp364Df0IAKOMnIMZ35K4uKCemZ7dVEtW
VvMgch2RZwEa+Oy8Og0o6WGYyurOR66w4oJqGlc9BYPaQo/akiKU0xLcQ2fqndsc
PnkberSaqER5/9COnSXLCWH9WsCW3rvdGHLg7ZicUiO+b6n/90hM4MRWL6j3QZCl
FYgMMEKSpPz7juZAdPIvfE4Mr157aESwmcHkihi7F4Ui6k2jln49R+zQoM6h9D/u
nH/pamxkfO/cJGQ3wcLVPhu6EL9wLqWU/+1/7FILYpoWkbiaJH3TtElQ3OU2yXq+
PmMcS8nI7Uv2Jrx66MfMx0fkCdA0lx5SlXsEmlwGtwk8A4qJq2AwTRvz5slHHTA=
=Upe0
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Minor doc fix, a DMI match for ideapad and a fix to toshiba-wmi to
avoid loading on non-toshiba systems.
Documentation/ABI:
- ibm_rtl: The "What:" fields are incomplete
toshiba-wmi:
- Fix loading the driver on non Toshiba laptops
ideapad-laptop:
- Add another DMI entry for Yoga 900"
* tag 'platform-drivers-x86-v4.9-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
Documentation/ABI: ibm_rtl: The "What:" fields are incomplete
toshiba-wmi: Fix loading the driver on non Toshiba laptops
ideapad-laptop: Add another DMI entry for Yoga 900
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5c2j
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
- Fix mmc card initialization for hosts not supporting HW busy detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mnjf
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix mmc card initialization for hosts not supporting HW busy
detection
- Fix mmc_test for sending commands during non-blocking write
MMC host:
- mxs: Avoid using an uninitialized
- sdhci: Restore enhanced strobe setting during runtime resume
- sdhci: Fix a couple of reset related issues
- dw_mmc: Fix a reset controller issue"
* tag 'mmc-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxs: Initialize the spinlock prior to using it
mmc: mmc: Use 500ms as the default generic CMD6 timeout
mmc: mmc_test: Fix "Commands during non-blocking write" tests
mmc: sdhci: Fix missing enhanced strobe setting during runtime resume
mmc: sdhci: Reset cmd and data circuits after tuning failure
mmc: sdhci: Fix unexpected data interrupt handling
mmc: sdhci: Fix CMD line reset interfering with ongoing data transfer
mmc: dw_mmc: add the "reset" as name of reset controller
Documentation: synopsys-dw-mshc: add binding for reset-names
- Fix a host of runtime problems with the Intel
Cherryview driver: suspend/resume needs to be
marshalled properly, and strange effects from BIOS
interaction during suspend/resume need to be
dealt with.
- A single bit was being set wrong in the Aspeed
driver.
- Fix an iProc probe ordering fallout resulting from
v4.9 refactorings for bus population.
- Do not specify a default trigger in the ST Micro
cascaded GPIO IRQ controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver,
it turns out not all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will
eventually crash if probed repeatedly, not good.
-----BEGIN PGP SIGNATURE-----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=ENR8
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"All is about drivers, no core business going on.
- Fix a host of runtime problems with the Intel Cherryview driver:
suspend/resume needs to be marshalled properly, and strange effects
from BIOS interaction during suspend/resume need to be dealt with.
- A single bit was being set wrong in the Aspeed driver.
- Fix an iProc probe ordering fallout resulting from v4.9
refactorings for bus population.
- Do not specify a default trigger in the ST Micro cascaded GPIO IRQ
controller: the kernel will moan.
- Make IRQs optional altogether on the STM32 driver, it turns out not
all systems have them or want them.
- Fix a re-probe bug in the i.MX driver, it will eventually crash if
probed repeatedly, not good"
* tag 'pinctrl-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl-aspeed-g5: Never set SCU90[6]
pinctrl: cherryview: Prevent possible interrupt storm on resume
pinctrl: cherryview: Serialize register access in suspend/resume
pinctrl: imx: reset group index on probe
pinctrl: stm32: move gpio irqs binding to optional
pinctrl: stm32: remove dependency with interrupt controller
pinctrl: st: don't specify default interrupt trigger
pinctrl: iproc: Fix iProc and NSP GPIO support
Add CRG driver for Hi3798CV200 SoC. CRG(Clock and Reset
Generator) module generates clock and reset signals used
by other module blocks on SoC.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the LS1046a PCIe controller. This device has a different
LUT_DBG offset, so add "lut_dbg" to ls_pcie_drvdata to
describe this difference.
[bhelgaas: changelog, remove now-unused PCIE_LUT_DBG]
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull VFS fixes from Al Viro:
"Christoph's and Jan's aio fixes, fixup for generic_file_splice_read
(removal of pointless detritus that actually breaks it when used for
gfs2 ->splice_read()) and fixup for generic_file_read_iter()
interaction with ITER_PIPE destinations."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
splice: remove detritus from generic_file_splice_read()
mm/filemap: don't allow partially uptodate page for pipes
aio: fix freeze protection of aio writes
fs: remove aio_run_iocb
fs: remove the never implemented aio_fsync file operation
aio: hold an extra file reference over AIO read/write operations
Yet another simple conversion from a plain text file.
Renamed to codec-to-codec.rst to align with others.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file.
The file name was renamed to lower letters to align with others.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file.
The file name was changed from "pops_clicks" to "pops-clicks" to align
with others.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file.
The section numbers and the item numbers are dropped to align with the
ReST format. Some lists are converted to description lists to be
clearer.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file with slight reformatting /
corrections.
The file name was changed to lower letters to align with others.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file.
The section numbers are dropped to align with other documents.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a plain text file.
Created a new subdirectory, Documentation/sound/soc, for this and
other ASoC documents.
Since the index page contains the TOC, so "Documentation" section got
removed from overview.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to have a proper topology of regulators for a platform, each
registering regulator needs to populate supply_name field for identifying
its supply's name. Add supply_name field for lp873x regulators.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow CPUfreq statistics to be cleared by writing anything to
/sys/.../cpufreq/stats/reset.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_rpm driver to communicate with RPM.
Such platforms are apq8064 and msm8960.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds initial support for clocks controlled by the Resource
Power Manager (RPM) processor on some Qualcomm SoCs, which use
the qcom_smd_rpm driver to communicate with RPM.
Such platforms are msm8916, apq8084 and msm8974.
The RPM is a dedicated hardware engine for managing the shared
SoC resources in order to keep the lowest power profile. It
communicates with other hardware subsystems via shared memory
and accepts clock requests, aggregates the requests and turns
the clocks on/off or scales them on demand.
This driver is based on the codeaurora.org driver:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/clk/qcom/clock-rpm.c
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove useless braces for single line if]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is the initial ZTE VOU display controller DRM/KMS driver. There
are still some features to be added, like overlay plane, scaling, and
more output devices support. But it's already useful with dual CRTCs
and HDMI display working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYH++oAAoJEFBXWFqHsHzOlCQIAKLNtBmB2OSChdPRCa7tIG7O
vtjUwze70QtD6vVe+rs0fvc46PM3qrccJI6bcgzveki+vRvFVDlreydmB18g3bMx
cBbsByGnWrNWDtKrwvvRWrkDQwcxnSVX5lMWeIvLrPHeXQVb4nf0F2cn7/zEfIek
G55LHonRD28m66tWb87gaWwisowcaPzA3tAEP4Rifdqg9IQ45He7Po6KZWZU4DQq
M/RltIHQwt/OFxAnDuz18ecf+o0NXuLoMYmoA8EYdOTV3sJ2hiJQFWaL5qmXKl7C
Nzlql70txu9B9H5R4V/6MXS21J0H2uGs2Aig9l9Brz2Vn774IBX09Wi8Fo8G8VU=
=+zjh
-----END PGP SIGNATURE-----
Merge tag 'zxdrm-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into drm-next
ZTE zxdrm driver support for 4.10:
This is the initial ZTE VOU display controller DRM/KMS driver. There
are still some features to be added, like overlay plane, scaling, and
more output devices support. But it's already useful with dual CRTCs
and HDMI display working.
[airlied: use drm_format_plane_cpp instead of legacy api]
* tag 'zxdrm-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
MAINTAINERS: add an entry for ZTE ZX DRM driver
drm: zte: add initial vou drm driver
dt-bindings: add bindings doc for ZTE VOU display controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
-----BEGIN PGP SIGNATURE-----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=aAzo
-----END PGP SIGNATURE-----
Merge tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next
dw-hdmi i2c master controller
- add support for the HDMI I2C master controller, for boards that
can have their DDC pins connected only to the HDMI TX directly.
* tag 'dw-hdmi-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
drm: bridge/dw_hdmi: add dw hdmi i2c bus adapter support
drm: dw_hdmi: use of_get_i2c_adapter_by_node interface
- better atomic state debugging from Rob
- fence prep from gustavo
- sumits flushed out his backlog of pending dma-buf/fence patches from
various people
- drm_mm leak debugging plus trying to appease Kconfig (Chris)
- a few misc things all over
* tag 'topic/drm-misc-2016-11-10' of git://anongit.freedesktop.org/drm-intel: (35 commits)
drm: Make DRM_DEBUG_MM depend on STACKTRACE_SUPPORT
drm/i915: Restrict DRM_DEBUG_MM automatic selection
drm: Restrict stackdepot usage to builtin drm.ko
drm/msm: module param to dump state on error irq
drm/msm/mdp5: add atomic_print_state support
drm/atomic: add debugfs file to dump out atomic state
drm/atomic: add new drm_debug bit to dump atomic state
drm: add helpers to go from plane state to drm_rect
drm: add helper for printing to log or seq_file
drm: helper macros to print composite types
reservation: revert "wait only with non-zero timeout specified (v3)" v2
drm/ttm: fix ttm_bo_wait
dma-buf/fence: revert "don't wait when specified timeout is zero" (v2)
dma-buf/fence: make timeout handling in fence_default_wait consistent (v2)
drm/amdgpu: add the interface of waiting multiple fences (v4)
dma-buf: return index of the first signaled fence (v2)
MAINTAINERS: update Sync File Framework files
dma-buf/sw_sync: put fence reference from the fence creation
dma-buf/sw_sync: mark sync_timeline_create() static
drm: Add stackdepot include for DRM_DEBUG_MM
...
- gpu idling rework for s/r (Imre)
- vlv mappable scanout fix
- speed up probing in resume (Lyude)
- dp audio workarounds for gen9 (Dhinakaran)
- more conversion to using dev_priv internally (Ville)
- more gen9+ wm fixes and cleanups (Maarten)
- shrinker cleanup&fixes (Chris)
- reorg plane init code (Ville)
- implement support for multiple timelines (prep work for scheduler)
from Chris and all
- untangle dev->struct_mutex locking as prep for multiple timelines
(Chris)
- refactor bxt phy code and collect it all in intel_dpio_phy.c (Ander)
- another gvt with bugfixes all over from Zhenyu
- piles of lspcon fixes from Imre
- 90/270 rotation fixes (Ville)
- guc log buffer support (Akash+Sagar)
- fbc fixes from Paulo
- untangle rpm vs. tiling-fences/mmaps (Chris)
- fix atomic commit to wait on the right fences (Daniel Stone)
* tag 'drm-intel-next-2016-11-08' of git://anongit.freedesktop.org/git/drm-intel: (181 commits)
drm/i915: Update DRIVER_DATE to 20161108
drm/i915: Mark CPU cache as dirty when used for rendering
drm/i915: Add assert for no pending GPU requests during suspend/resume in LR mode
drm/i915: Make sure engines are idle during GPU idling in LR mode
drm/i915: Avoid early GPU idling due to race with new request
drm/i915: Avoid early GPU idling due to already pending idle work
drm/i915: Limit Valleyview and earlier to only using mappable scanout
drm/i915: Round tile chunks up for constructing partial VMAs
drm/i915: Remove the vma from the object list upon close
drm/i915: Reinit polling before hpd when resuming
drm/i915: Remove redundant reprobe in i915_drm_resume
drm/i915/dp: Extend BDW DP audio workaround to GEN9 platforms
drm/i915/dp: BDW cdclk fix for DP audio
drm/i915: Fix pages pin counting around swizzle quirk
drm/i915: Fix test on inputs for vma_compare()
drm/i915/guc: Cache the client mapping
drm/i915: Tidy slab cache allocations
drm/i915: Introduce HAS_64BIT_RELOC
drm/i915: Show the execlist queue in debugfs/i915_engine_info
drm/i915: Unify global_list into global_link
...
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
[sboyd@codeaurora.org: Dropped unused and incorrect GDSC defines]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A simple conversion from a plain text file. Quite a few reformatting
in the end due to the style of the original document.
Put to cards directory.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable throttling of buffered writeback to make it a lot
more smooth, and has way less impact on other system activity.
Background writeback should be, by definition, background
activity. The fact that we flush huge bundles of it at the time
means that it potentially has heavy impacts on foreground workloads,
which isn't ideal. We can't easily limit the sizes of writes that
we do, since that would impact file system layout in the presence
of delayed allocation. So just throttle back buffered writeback,
unless someone is waiting for it.
The algorithm for when to throttle takes its inspiration in the
CoDel networking scheduling algorithm. Like CoDel, blk-wb monitors
the minimum latencies of requests over a window of time. In that
window of time, if the minimum latency of any request exceeds a
given target, then a scale count is incremented and the queue depth
is shrunk. The next monitoring window is shrunk accordingly. Unlike
CoDel, if we hit a window that exhibits good behavior, then we
simply increment the scale count and re-calculate the limits for that
scale value. This prevents us from oscillating between a
close-to-ideal value and max all the time, instead remaining in the
windows where we get good behavior.
Unlike CoDel, blk-wb allows the scale count to to negative. This
happens if we primarily have writes going on. Unlike positive
scale counts, this doesn't change the size of the monitoring window.
When the heavy writers finish, blk-bw quickly snaps back to it's
stable state of a zero scale count.
The patch registers a sysfs entry, 'wb_lat_usec'. This sets the latency
target to me met. It defaults to 2 msec for non-rotational storage, and
75 msec for rotational storage. Setting this value to '0' disables
blk-wb. Generally, a user would not have to touch this setting.
We don't enable WBT on devices that are managed with CFQ, and have
a non-root block cgroup attached. If we have a proportional share setup
on this particular disk, then the wbt throttling will interfere with
that. We don't have a strong need for wbt for that case, since we will
rely on CFQ doing that for us.
Signed-off-by: Jens Axboe <axboe@fb.com>
pm_rst, aclk_rst, pclk_rst was controlled by ROM code so the software
wasn't needed to control it again in theory. But it didn't work properly,
so we do need to do it again and add enough delay between the assert of
pm_rst and the deassert of pm_rst. The Soc intergrated with this
controller, rk3399, is still under MP test internally, so the backward
compatibility won't be a big deal.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
A conversion from a simple text file.
A new subdirectory, cards, was created to contain the card-specific
information like this one.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Converted from an ancient plain HTML document. It's much readable now!
Put to designs subdirectory with a slight rename.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a text file.
Put into designs subdirectory, although it's mostly relevant with
HD-audio.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from a text file.
A new subidrectory, Documentation/sound/designs, was created to put
this document. The other API design and implementation docuemnts
will be put to that directory in later commits.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion from the text file.
Since this is the only document specific to the configurations, it's
put to the root sound subdirectory.
A section describing the obsoleted configure stuff of old alsa-driver
tarball got removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple reformat with the description list of ReST, and the content
was kept as is, but renamed as Documentation/sound/hd-audio/models.rst.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The original HD-Audio.txt was already in asciidoc format, so it's a
simple conversion in the end.
A new subdirectory, Documentation/sound/hd-audio, is created and the
document is moved there with another file name to match better with
the recent Documentation tree structure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another simple conversion from DocBook to ReST.
This required a few manual fixups and reformats, but the most of
contents are kept as is.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A simple conversion of alsa-driver-api document from DocBook to ReST.
It's moved to the new Documentation/sound/kernel-api subdirectory that
will contain other ALSA kernel API documents.
The GPL legal note was removed, as it's superfluous (and doesn't fit
with ReST kernel docs pretty well).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a really obsoleted information, effectively just listing the
module names. Let's get rid of it for avoiding confusions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since there is not enough tcam table entries for every vlan and multicast
address, HNS needs to add support of fuzzy matching of TCAM tables. Adding
the property to mask the bits to be fuzzy matched, so update the bindings
document
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is sometimes useful to know that a device is on the deferred probe
list rather than, say, not having a driver available. Expose this
information to user-space.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New bindings document for FPGA Region to support programming
FPGA's under Device Tree control
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a minor change in the FPGA Manager API
to hold information that is specific to an FPGA image
file. This change is expected to bring little, if any,
pain.
An FPGA image file will have particulars that affect how the
image is programmed to the FPGA. One example is that
current 'flags' currently has one bit which shows whether the
FPGA image was built for full reconfiguration or partial
reconfiguration. Another example is timeout values for
enabling or disabling the bridges in the FPGA. As the
complexity of the FPGA design increases, the bridges in the
FPGA may take longer times to enable or disable.
This patch documents the change in the FPGA Manager API
functions, replacing the 'u32 flag' parameter with a pointer
to struct fpga_image_info.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intent is to provide a non-DT method of getting
ahold of a FPGA manager to do some FPGA programming.
This patch refactors of_fpga_mgr_get() to reuse most of it
while adding a new method fpga_mgr_get() for getting a
pointer to a fpga manager struct, given the device.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
CC: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add RZ/G1E (R8A7745) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add RZ/G1M (R8A7743) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds documentation for some SR-related per-interface
sysctls.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is some difference between force_igmp_version and force_mld_version.
Add document to make users aware of this.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRA71x processor family is a derivative of DRA722 ES2.0 targetted for
infotainment systems.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to support PHY switching on Amlogic GXL SoCs, add support for
16bit and 32bit registers sizes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devicetree bindings documentation file for Cirrus
Logic CS42L42 codec.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add binding information for DA9061 onkey.
This patch updates the compatible string "dlg,da9061-onkey" to support
DA9061, removes the reference to KEY_SLEEP (which the driver no longer
supports) and fixes a typo in the example for DA9063.
Supporting KEY_SLEEP was not the general convention and the typical
solution should have been for KEY_POWER to support both cases of suspend
and S/W power off. This change was sent to the DA9063 ONKEY device
driver in a separate patch, but the documentation was not updated at
that time.
- f889bea Report KEY_POWER instead of KEY_SLEEP during power key-press
This patch also adds two new examples, one for DA9062 and one for DA9061.
The DA9061 examples uses a fall-back compatible string for the DA9062
onkey driver.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a new compatible string for 14nm ufs phy present on msm8996
chipset. This phy is bit different from the legacy 14nm ufs phy
in terms of the clocks that are needed to be handled in the driver.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for hip07 chipset to hisi_sas controller.
Chipset hip07 has v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Add support for the r8a7743 SoC to rcar-sysc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XcYr
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Renesas ARM Based SoC Drivers Updates for v4.10
* Add support for the r8a7743 SoC to rcar-sysc
* tag 'renesas-drivers-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: add R8A7743 support
ARM: shmobile: r8a7743: add power domain index macros
Signed-off-by: Olof Johansson <olof@lixom.net>
A typo sneaked in the latest change on the USB documentation. Fixing it
and also a trailing whitespace since it is also in the "USB Host-Side API
Model" chapter.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Commit 865a1caa4b ("CodingStyle: Clarify and complete chapter 7")
renamed the label "out_buffer" to "out_free_buffer", but missed to
change this line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Removes intermediate 'Documentation/DocBook/.*.xml.cmd' files
Changes since v1:
- Reduce the patch to DocBook cleandocs
References: http://lkml.kernel.org/r/CA+r1Zhjr5SCVAroREBv84t9bxDVu5jVJ_Fu=BbVDGNNABdQOuQ@mail.gmail.com
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In order too make Documentation root directory cleaner move the tpm
directory under Documentation/security.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Transitioned the tpm_vtpm_proxy documentation to the Sphinx
infrastructure and removed parts from the documentation that are easier
to pull from the sources. Restructured vtpm_proxy.h and tpm_vtpm_proxy.c
to be compatible with this approach and wrote associated documentation
comments.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add Qualcomm QCA tagging introduced in cafdc45c9 to the
list of supported protocols.
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update kselftest.txt with details on how to run tests after install.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It seems we can't have literal blocks in footnotes, which almost actually
makes some sense. So just use basic ``monospace`` instead.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
`Specific guidelines for the kernel documentation` section of
`kernel-documentation.rst` suggests to use ``~`` for subsection but
subsections in HOWTO is not marked in the format. This commit marks
them in the format.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Because few sentences has no whitespace between URL and text, few
document viewers fail to properly parse the URL from it. This commit
adds whitespace between them to fix the problem.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies commit 1b49ecf2f3 ("docs: Clean up bare :: lines")
to Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit appplies commit f1eebe92c2 ("Documentation/HOWTO: adjust
external link references") to Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies commit 34fed7e7e0 ("Documentation/HOWTO: improve
some markups to make it visually better") to Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies commit 43fb67a525 ("Documentation/HOWTO: update
information about generating documentation") to Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies commit 609d99a3b7 ("Documentation/HOWTO: add
cross-references to other documents") to Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies commit 022e04d6f5 ("Documentation/HOWTO: convert
to ReST notation") to Korean translation and fix a trivial ReST build
failure problem.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit fixes subtitles style. It aligns them with their header,
adjust blank lines between them properly.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
`Specific guidelines for the kernel documentation` section of
`kernel-documentation.rst` suggests to use ``~`` for subsection but
subsections in HOWTO is not marked in the format. This commit marks
them in the format.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Now that oops-tracing.rst has only information about
stack dumps found on OOPS, and bug-hunting.rst has only
information about how to identify the source code line
associated with a stack dump, let's merge them and
improve the information inside it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The tainted kernels info is not directly related to
the oops tracing. So, let's move it to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Better organize the admin guide documentation by moving the
bug bisect to a separate file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The document shows a really old procedure for bug hunting that
nobody uses anymore. Remove such section, and update the
remaining documentation to reflect the procedures used
currently.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Peter Ujfalusi <perter.ujfalusi@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add atmel,sama5d2-securam to the compatible list.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
A security module is available starting with sama5d2, add its bindings.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
ARM systems may be configured to have cpus with different power/performance
characteristics within the same chip. In this case, additional information
has to be made available to the kernel (the scheduler in particular) for it
to be aware of such differences and take decisions accordingly.
Therefore, this patch aims at standardizing cpu capacities device tree
bindings for ARM platforms. Bindings define cpu capacity-dmips-mhz
parameter, to allow operating systems to retrieve such information from
the device tree and initialize related kernel structures, paving the way
for common code in the kernel to deal with heterogeneity.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation for PHY lane swapping. This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds the device tree bindings description for Samsung S3C2410 and
compatible NAND flash controller.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The description for dmas references a second property, which should be
"dma-names" instead of "clock-names".
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The content of the directories and files in the info directory of the
resctrl filesystem are not documented.
Add the missing bits and pieces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shaohua Li <shli@fb.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
-----BEGIN PGP SIGNATURE-----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=ptGw
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
Second round of new device support, cleanups and fixes for IIO in the 4.10 cycle
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
Add reset-names property for binding dw-mmc controller.
It might be used together with "reset" property.
- Note: It must be "reset" as name.
Fixes: d6786fefe8 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It adds initial bindings doc for ZTE VOU display controller. HDMI is
the only supported output device right now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc4' into drm-next
Linux 4.9-rc4
This is needed for nouveau development.
Add interrupts documentation
Fix example and formatting
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Initial pinctrl driver for QCOM msm8994 platforms.
In order to continue the initial board support for QCOM msm8994/msm8992
presented in patches from Jeremy McNicoll <jeremymc@redhat.com>, let's put
a proper pinctrl driver in place.
Currently, the DT for these platforms uses the msm8x74 pinctrl driver to
enable basic UART. Beyond the first few pins the rest are different enough
to justify it's own driver.
Note: This driver is also used by QCOM's msm8992 platform as it's TLM block
is the same.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
- Data was then adjusted per QCOM MSM8994v2 documentation for Top Level
Multiplexing
- Bindings documentation was based on qcom,msm8996-pinctrl.txt by
Joonwoo Park <joonwoop@codeaurora.org> and then modified for msm8994
content
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds documentation for the device-tree bindings of the
jz4740-rtc driver, which supports the RTC unit present in the JZ4740 and
JZ4780 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
during the merge window. The rest are fixes for MIPS, s390 and nested VMX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYG2H5AAoJEL/70l94x66DK/cH/0jEQ3ynuLAd5CKux7JxI/EP
msSJh1Xqr4+XhXZnuDpGQWrdsBlxoiqA6PsJrUTtyi4nQCDXlT8g+2MDuvqhWIHz
7vw58j/EMJDCVQzYAbN5VDUfk13uB5aSWTo3M9Rf09v0hU1Ql7z8u4CtKEdLpN5Y
LY9bT9fxUmXO7REKP7bdW6ZrDX/hUShYHgMqzXGFMyGBG3ym3a9bggXEzTCD6eNQ
ioogQIWqg+icdhta0iLNAwFClPlcKB2/xo4IUuNgrPwGoHFGJN/8+qxT4+sVbp2B
v8u1zOXlCFXBcskWE+yRRsGe72+mIzz6QScCyO+5HbhKYVfbE9H7KBlFX9rZZ2c=
=IbKx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One NULL pointer dereference, and two fixes for regressions introduced
during the merge window.
The rest are fixes for MIPS, s390 and nested VMX"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: Check memopp before dereference (CVE-2016-8630)
kvm: nVMX: VMCLEAR an active shadow VMCS after last use
KVM: x86: drop TSC offsetting kvm_x86_ops to fix KVM_GET/SET_CLOCK
KVM: x86: fix wbinvd_dirty_mask use-after-free
kvm/x86: Show WRMSR data is in hex
kvm: nVMX: Fix kernel panics induced by illegal INVEPT/INVVPID types
KVM: document lock orders
KVM: fix OOPS on flush_work
KVM: s390: Fix STHYI buffer alignment for diag224
KVM: MIPS: Precalculate MMIO load resume PC
KVM: MIPS: Make ERET handle ERL before EXL
KVM: MIPS: Fix lazy user ASID regenerate for SMP
Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2E
board. TM2E board is very similar to the TM2 board so the
exynos5433-tm2e.dts includes the TM2 DTS and overrides the differences.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Now that we don't have automatic syntax highlighting, use the code-block
directive with the explicitly selected language, where appropriate.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we don't have automatic syntax highlighting, use the code-block
directive with the explicitly selected language, where appropriate.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we don't have automatic syntax highlighting, use the code-block
directive with the explicitly selected language, where appropriate.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Set the default highlight language to "none", i.e. do not try to guess
the language and do automatic syntax highlighting on literal blocks.
Eyeballing around the generated documentation, we don't seem to actually
have a lot of literal blocks that would benefit from syntax
highlighting. The C code blocks we do have are typically very short, and
most of the literal blocks are things that shouldn't be highlighted (or,
do not have a pygments lexer). This seems to be true for literal blocks
both in the rst source files and in source code comments.
Not highlighting code is never wrong, but guessing the language wrong
almost invariably leads to silly or confusing highlighting.
At the time of writing, admin-guide/oops-tracing.rst and
admin-guide/ramoops.rst contain good examples of 1) a small C code
snippet not highlighted, 2) a hex dump highligted as who knows what, 3)
device tree block highlighted as C or maybe Python, 4) a terminal
interaction highlighted as code in some language, and finally, 5) some C
code snippets correctly identified as C. I think we're better off
disabling language guessing, and going by explicitly identified
languages for longer code blocks.
It is still possible to enable highlighting on an rst source file basis
using the highlight directive:
.. higlight:: language
and on a literal block basis using the code-block directive:
.. code-block:: language
See http://www.sphinx-doc.org/en/latest/markup/code.html for details.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add missing semicolon to fix pdf build with more than one SPHINXDIRS
directory specified. For example make SPHINXDIRS="gpu media" pdfdocs.
Fixes: cd21379b16 ("doc-rst: generic way to build PDF of sub-folders")
Signed-off-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Radically reduce the noise on stdout. The full build logs will still be
available under Documentatio/output/latex/*.log.
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tested-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the unnecessary ; removed, the terminal URL detection also works
better.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Building latexdocs doesn't actually require $(PDFLATEX). Move the checks
for it to the pdfdocs target which does require it, and specifically
outside of the target in order to not depend on latexdocs when we can't
build pdfdocs anyway.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tested-by: Markus Heiser <markus.heiser@darmarIT.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Refer to xelatex and latex options via variables. This allows the user
to override the pdflatex and latex options to use on the make command
line for experimenting. As a side effect, this makes the makefile a bit
tidier.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Change title prefix to match the usual style]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the A64 CCU clocks set.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
H3 SPI has same architecture as A31 except FIFO capacity.
To configure the buffer size separately, compatible property should be
different. Optional DMA specifiers and example are added.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT bindings for the Renesas R-Car Reset Controller (R-Car Gen1
RESET/WDT and R-Car Gen2/Gen3 and RZ/G RST).
As the features provided by the hardware module differ a lot across the
various SoC families and members, only SoC-specific compatible values
are defined.
For now we use the RST only for providing access to the state of the
mode pins, which is needed by the clock driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Document the SK-RZG1M device tree bindings, listing it as a supported board.
This allows to use checkpatch.pl to validate .dts files referring to the
SK-RZG1M board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add minimal support for the RZ/G1M (R8A7743) SoC.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There are display panels which demands that the sync signal is driven on
different edge than the pixel data.
With the syncclk-active property we can specify the clk edge to be used to
drive the sync signal. When the property is missing it indicates that the
sync is driven on the same edge as the pixel data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add device tree support for the tsl2583 IIO driver with no custom
properties.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds devicetree support for the si7020 iio driver. Since it works
well without requiring any additional property, its compatible string is
added to the trivial i2c devices bindings list.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The "What:" field at the ABI should describe the location of
the ABI, e. g. the position under a mounted sysfs. However,
this file has only the basename without the path.
Fix it.
Cc: Vernon Mauery <vernux@us.ibm.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Noidle should be the default for writes as seen by all the compounds
definitions in fs.h using it. In fact only direct I/O really should
be using NODILE, so turn the whole flag around to get the defaults
right, which will make our life much easier especially onces the
WRITE_* defines go away.
This assumes all the existing "raw" users of REQ_SYNC for writes
want noidle behavior, which seems to be spot on from a quick audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The type of AVIC interrupt controller found on i.MX31 is one-cell,
namely 31 for CCM DVFS and 53 for CCM, however for clock control
module its interrupts are specified as 3-cells, fix it.
Fixes: ef0e4a606f ("ARM: mx31: Replace clk_register_clkdev with clock DT lookup")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the binding document for the new brcmstb-avs-cpufreq driver.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Additional command line control to enable per core performance
control.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Document restriction on per core P-State control.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a sysfs interface to rproc allowing the firmware name
and processor state to be changed dynamically.
State was previously available in debugfs, and is replicated here. The
firmware file allows retrieval of the running firmware name, and a new
one to be specified at run time, so long as the remote processor has
been stopped.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
stm32 pinctrl driver could be probed even if no interrupt controller
is defined to manage gpio irqs. Entries related to gpio irq management
are moved to optional.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The address of the mailbox node in the example has a typo.
So fix it accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: d4b5c782b9 ("dt/bindings: Add binding for the BCM2835 mailbox driver")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch introduces a vendor prefix for Holtek Semiconductor Inc.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HBM protocol version is negotiated during the setup phase, then settled
on a highest possible common version of the driver and the firmware.
The sysfs API advertises both negotiated and driver supported versions
in the device attributes.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for pin output control through the pinctrl config:
- support enabling/disabling output on a given pin
- support output level setting (high or low)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add power dt-bindings for MT2701.
Signed-off-by: Shunli Wang <shunli.wang@mediatek.com>
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The "What:" field at the ABI should describe the location of
the ABI, e. g. the position under a mounted sysfs.
Fix it.
Cc: Mark Godfrey <mark.godfrey@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves a merge issue with
drivers/staging/iio/accel/sca3000_core.c and we want the fixes all in
here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default sched_clock() implementation is native_sched_clock(). It
contains code to handle non constant frequency TSCs, which creates
overhead for systems with constant frequency TSCs.
The vmware hypervisor guarantees a constant frequency TSC, so
native_sched_clock() is not required and slower than a dedicated function
which operates with one time calculated conversion factors.
Calculate the conversion factors at boot time from the tsc frequency and
install an optimized sched_clock() function via paravirt ops.
The paravirtualized clock can be disabled on the kernel command line with
the new 'no-vmw-sched-clock' option.
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Acked-by: Alok N Kataria <akataria@vmware.com>
Cc: linux-doc@vger.kernel.org
Cc: pv-drivers@vmware.com
Cc: corbet@lwn.net
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/20161028075432.90579-4-amakhalov@vmware.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----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=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
order):
- bump version strings, by Simon Wunderlich
- README updates/clean up, by Sven Eckelmann (4 patches)
- Code clean up and restructuring by Sven Eckelmann (2 patches)
- Kerneldoc fix in forw_packet structure, by Linus Luessing
- Remove unused argument in dbg_arp, by Antonio Quartulli
- Add support to build batman-adv without wireless, by Linus Luessing
- Restructure error handling for is_ap_isolated, by Markus Elfring
- Remove unused initialization in various functions, by Sven Eckelmann
- Use better names for fragment and gateway list heads, by Sven
Eckelmann (2 patches)
- Convert to octal permissions for files, by Sven Eckelmann
- Avoid precedence issues for some macros, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=eDGz
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20161027' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This code cleanup patchset includes the following changes (chronological
order):
- bump version strings, by Simon Wunderlich
- README updates/clean up, by Sven Eckelmann (4 patches)
- Code clean up and restructuring by Sven Eckelmann (2 patches)
- Kerneldoc fix in forw_packet structure, by Linus Luessing
- Remove unused argument in dbg_arp, by Antonio Quartulli
- Add support to build batman-adv without wireless, by Linus Luessing
- Restructure error handling for is_ap_isolated, by Markus Elfring
- Remove unused initialization in various functions, by Sven Eckelmann
- Use better names for fragment and gateway list heads, by Sven
Eckelmann (2 patches)
- Convert to octal permissions for files, by Sven Eckelmann
- Avoid precedence issues for some macros, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We haven't seen a whole lot of fixes for the first two weeks since the merge
window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful of
smaller fixes to several platforms. The Uniphier reset controller changes
could probably have been delayed to 4.10, but they're not scary and just
plumbing up driver changes that went in during the merge window.
We're also adding another maintainer to Marvell Berlin platforms, to help
out when Sebastian is too busy. Yay teamwork!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OGbj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally the
atmel serial driver is back working properly.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0WQPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwmIAoJYQ
5fdXVYgwh59wn0E4xuKWSH84AJ9bTIe3MDED9TrE1rocnLaj9wxIuw==
=os0d
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Here are a number of small USB driver fixes for 4.9-rc3. There is the
usual number of gadget and xhci patches in here to resolved reported
issues, as well as some usb-serial driver fixes and new device ids.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlgU0foPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspqE4Ani3Y
N4J9W4SeXT7ilLLQoeLznUv8AJ4sm/Uy5d4syBa+TVEPuAHXort+vw==
=ICZX
-----END PGP SIGNATURE-----
Merge tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
- A couple .request_fn request-based DM NULL pointer fixes
- A fix for a DM target reference count leak, on target load error, that
prevented associated DM target kernel module(s) from being removed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYEo+lAAoJEMUj8QotnQNaGfkH/jGqr4bj4l2Ty3QgV95fYW7+
lqp4Flkevm35HotEGKuuizvqbbVrj57BCGLE+dV48/X2cv5QbUFht6QBu9iJTrk6
Q7VqyBOvDDnOZHIof5CfKBeLZ2gd8YHZwUpYvzJcThSWS1+LjeVqg8a33LMZroMQ
rghVxFCIKy6LqCryIiTHk1t+OfmuBz3S2LXcQXFY7XAPpWq/f+V66gthTZUpm86+
Gu1xOHQlvnmf5xnDUxCpPVbQNY334D/aSbU73i2cdvfL1pkxBFNcI+LbPcu+sNP9
ugGjPj4etbIRsVysuW3fLhn2kKqaXXVuD1rLTQ+C3ytciI+RQJvG892gWhAABRQ=
=apHk
-----END PGP SIGNATURE-----
Merge tag 'dm-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a couple DM raid and DM mirror fixes
- a couple .request_fn request-based DM NULL pointer fixes
- a fix for a DM target reference count leak, on target load error,
that prevented associated DM target kernel module(s) from being
removed
* tag 'dm-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: fix missing dm_put_target_type() in dm_table_add_target()
dm rq: clear kworker_task if kthread_run() returned an error
dm: free io_barrier after blk_cleanup_queue call
dm raid: fix activation of existing raid4/10 devices
dm mirror: use all available legs on multiple failures
dm mirror: fix read error on recovery after default leg failure
dm raid: fix compat_features validation
Now that we don't need the common flags to overflow outside the range
of a 32-bit type we can encode them the same way for both the bio and
request fields. This in addition allows us to place the operation
first (and make some room for more ops while we're at it) and to
stop having to shift around the operation values.
In addition this allows passing around only one value in the block layer
instead of two (and eventuall also in the file systems, but we can do
that later) and thus clean up a lot of code.
Last but not least this allows decreasing the size of the cmd_flags
field in struct request to 32-bits. Various functions passing this
value could also be updated, but I'd like to avoid the churn for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch adds the QSPI clock for stm32f469 discovery board.
The gate mapping is a little bit different from stm32f429 soc.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The creation of the admin and process guides is a great thing, but, without
care, we risk replacing a messy docs directory with a few messy Sphinx
books. In an attempt to head that off and show what I'm thinking, here's a
set of tweaks that, I think, make the existing Sphinx-formatted docs a bit
more accessible.
It does no good to mention The 2.4 kernel series and neglect
USB 3.x and XHCI. Also with type C and micro/mini USB we better
not talk about the shape of connectors.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is ancient stuff and we don't do things this way anymore. In the
absence of simply deleting the document, at least add a warning to it.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is crufty stuff and should maybe just be deleted, but I'm not quite
ready to do that yet.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
I believe this makes the page as a whole more approachable.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The main goal here was to get the subsections to show in the TOC as they do
for all the other documents. Also call out the DCO in the section title
since it's important.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Put like documents together, with the essential ones at the top, and split
the TOC into sections.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The document has not been touched in over 11 years and doesn't reflect how
profiling is done in the perf era.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The last release of this tool was for 2.6.28; it's hard to see how it has
any relevance to current kernels.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The admin guide is a good start, but it's time to turn it into something
better than an unordered blob of files. This is a first step in that
direction. The TOC has been split up and annotated, the guides have been
reordered, and minor tweaks have been applied to a few of them.
One consequence of splitting up the TOC is that we don't really want to use
:numbered: anymore, since the count resets every time and there doesn't
seem to be a way to change that. Eventually we probably want to group the
documents into sub-books, at which point we can go back to a single TOC,
but it's probably early to do that.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Let's make the title of this document (which shows up in the top page)
better describe its contents.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This will be the initial landing point for readers, so give them a bit of
introductory material. Also split the TOC into area-specific chunks to
make the whole thing a bit more approachable.
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Some resources, such as IPPC register etc, shared with device
driver are moved into common glue layer when xHCI driver is the
host side of dual-role mode and they should be changed as optional
properties if they are required ones before. For clarity, add
a new part of binding to support host side of dual-role mode.
Additionally add optional properties of pinctrl for host only mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas RZ/G SoC also have the SCIF, SCIFA, SCIFB, and HSCIF ports and
they seem compatible with the R-Car gen2 SoC in this respect...
Document RZ/G1[ME] (also known as R8A774[35]) SoC bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These macros:
* CAN_LOAD_EGA_FONTS
* CAN_LOAD_PALETTE
* TRIDENT_GLITCH
* VGA_CAN_DO_64KB
* SLOW_VGA
are either always set or always unset. They come from the linux 2.1
times. And given nobody switched them to some configurable options, I
assume nobody actually uses them.
So remove the macros and leave in place appropriate branches of the
conditional code.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: <linux-fbdev@vger.kernel.org>
Cc: <linux-doc@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch Adds the new compatible string for ZynqMP SoC.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FCP IP cores include a version register that identifies which SoC
model the IP is integrated in. SoC-specific compatible strings are not
needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is long overdue, and not really hard.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1476357057-17899-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those in
newer SoCs in the keystone processor family starting with K2G.
This message protocol is used to communicate between various compute
or processing entities (such as ARM, DSP etc.) with a central system
controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC.
The message protocol can be found here:
http://processors.wiki.ti.com/index.php/TISCI
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This allows to build PDF of only the sub-projects, which reduce the
roundtrip compared to build the PDF from the main documentation.
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The index should only be included if the build of the sub-folder is done
with the html-builder (HTML output).
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add minimal conf.py makes the driver-api folder buildable
stand-alone. To build only this folder run::
make SPHINXDIRS=driver-api htmldocs
make SPHINXDIRS=driver-api pdfdocs
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add minimal conf.py and moved dev-tools/tools.rst to dev-tools/index.rst
makes the dev-tools folder buildable stand-alone. To build only this
folder run::
make SPHINXDIRS=dev-tools htmldocs
make SPHINXDIRS=dev-tools pdfdocs
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This updates the Device Tree according to the preferred way of parsing
the nodes using the regulator framework.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Merge Mauro's massive patch series creating the process and admin-guide
books. I think there's a lot of stuff to clean up here, but there's no
point in holding things up for that.
Mauro sez:
This patch series continues the efforts of converting the Linux Kernel
documentation to Sphinx.
It contains text to ReST conversion of several files under Documentation,
and a few ones under the main dir (README, REPORTING-BUGS).
All patches on this series can be found on my development tree:
https://git.linuxtv.org/mchehab/experimental.git/log/?h=lkml-books-v2
The Kernel docs html output after this series can be seen at:
https://mchehab.fedorapeople.org/kernel_docs/
Fix some minor spelling errors and capitalization issues.
Signed-off-by: Igor Vuk <parcijala@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit applies upstream change, commit ebff09a6ff
("locking/Documentation: Clarify limited control-dependency scope"), to
Korean translation.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add the core functions to be able to support the sensors attached behind
the ChromeOS Embedded Controller and used by other IIO cros-ec sensor
drivers.
The cros_ec_sensor_core driver matches with current driver in ChromeOS
4.4 tree, so it includes all the fixes at the moment. The support for
this driver was made by Gwendal Grignou. The original patch and all the
fixes has been squashed and rebased on top of mainline.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
[eballetbo: split, squash and rebase on top of mainline the patches
found in ChromeOS tree]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For mostly historical reasons, the x86 oops dump shows the raw stack
values:
...
[registers]
Stack:
ffff880079af7350 ffff880079905400 0000000000000000 ffffc900008f3ae0
ffffffffa0196610 0000000000000001 00010000ffffffff 0000000087654321
0000000000000002 0000000000000000 0000000000000000 0000000000000000
Call Trace:
...
This seems to be an artifact from long ago, and probably isn't needed
anymore. It generally just adds noise to the dump, and it can be
actively harmful because it leaks kernel addresses.
Linus says:
"The stack dump actually goes back to forever, and it used to be
useful back in 1992 or so. But it used to be useful mainly because
stacks were simpler and we didn't have very good call traces anyway. I
definitely remember having used them - I just do not remember having
used them in the last ten+ years.
Of course, it's still true that if you can trigger an oops, you've
likely already lost the security game, but since the stack dump is so
useless, let's aim to just remove it and make games like the above
harder."
This also removes the related 'kstack=' cmdline option and the
'kstack_depth_to_print' sysctl.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/e83bd50df52d8fe88e94d2566426ae40d813bf8f.1477405374.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds device tree bindings for the MPU-3050 gyroscope. Since it
is the first set of bindings for a gyroscope, the folder for it
is also created.
Cc: devicetree@vger.kernel.org
Cc: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is useless as it dumps the MSRs too early BUT(!) we do set MSRs later too.
Also, it dumps only BSP MSRs as it gets called only for CPU 0.
And the MSR range array would need constant updating anyway, and so on
and so on...
Oh, and we have msr.ko and msr-tools which are the much better solution
anyway. So off it goes...
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161024173844.23038-4-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
First -misc pull for 4.10:
- drm_format rework from Laurent
- reservation patches from Chris that missed 4.9.
- aspect ratio support in infoframe helpers and drm mode/edid code
(Shashank Sharma)
- rotation rework from Ville (first parts at least)
- another attempt at the CRC debugfs interface from Tomeu
- piles and piles of misc patches all over
* tag 'topic/drm-misc-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (55 commits)
drm: Use u64 for intermediate dotclock calculations
drm/i915: Use the per-plane rotation property
drm/omap: Use per-plane rotation property
drm/omap: Set rotation property initial value to BIT(DRM_ROTATE_0) insted of 0
drm/atmel-hlcdc: Use per-plane rotation property
drm/arm: Use per-plane rotation property
drm: Add support for optional per-plane rotation property
drm/atomic: Reject attempts to use multiple rotation angles at once
drm: Add drm_rotation_90_or_270()
dma-buf/sync_file: hold reference to fence when creating sync_file
drm/virtio: kconfig: Fixup white space.
drm/fence: release fence reference when canceling event
drm/i915: Handle early failure during intel_get_load_detect_pipe
drm/fb_cma_helper: do not free fbdev if there is none
drm: fix sparse warnings on undeclared symbols in crc debugfs
gpu: Remove depends on RESET_CONTROLLER when not a provider
i915: don't call drm_atomic_state_put on invalid pointer
drm: Don't export the drm_fb_get_bpp_depth() function
drm/arm: mali-dp: Replace drm_fb_get_bpp_depth() with drm_format_plane_cpp()
drm: vmwgfx: Replace drm_fb_get_bpp_depth() with drm_format_info()
...
of fixes for the uniphier clk driver that was introduced recently, as well as
Kconfig option hiding, module autoloading markings, and a few fixes for clk_hw
based registration patches that went in this merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mWXv
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"This is the first batch of clk driver fixes for this release.
We have a handful of fixes for the uniphier clk driver that was
introduced recently, as well as Kconfig option hiding, module
autoloading markings, and a few fixes for clk_hw based registration
patches that went in this merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: Fix a return value in case of error
clk: uniphier: rename MIO clock to SD clock for Pro5, PXs2, LD20 SoCs
clk: uniphier: fix memory overrun bug
clk: hi6220: use CLK_OF_DECLARE_DRIVER for sysctrl and mediactrl clock init
clk: mvebu: armada-37xx-periph: Fix the clock gate flag
clk: bcm2835: Clamp the PLL's requested rate to the hardware limits.
clk: max77686: fix number of clocks setup for clk_hw based registration
clk: mvebu: armada-37xx-periph: Fix the clock provider registration
clk: core: add __init decoration for CLK_OF_DECLARE_DRIVER function
clk: mediatek: Add hardware dependency
clk: samsung: clk-exynos-audss: Fix module autoload
clk: uniphier: fix type of variable passed to regmap_read()
clk: uniphier: add system clock support for sLD3 SoC
- Fix up off-by one and line offset validation, info leak to
userspace, and reject invalid flags. Those are especially
valuable hardening patches from Lars-Peter Clausen, all tagged
for stable.
- Fix module autoload for TS4800 and ATH79.
- Correct the IRQ handler for MPC8xxx to use handle_level_irq()
as it (A) reacts to edges not levels and (B) even implements
.irq_ack(). We were missing IRQs here.
- Fix the error path for acpi_dev_gpio_irq_get()
- Fix a memory leak in the MXS driver.
- Fix an annoying typo in the STMPE driver.
- Put a dependency on sysfs to the mockup driver.
-----BEGIN PGP SIGNATURE-----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=dVE6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a set of GPIO fixes for the v4.9 kernel series:
- Fix up off-by one and line offset validation, info leak to
userspace, and reject invalid flags. Those are especially valuable
hardening patches from Lars-Peter Clausen, all tagged for stable.
- Fix module autoload for TS4800 and ATH79.
- Correct the IRQ handler for MPC8xxx to use handle_level_irq() as it
(a) reacts to edges not levels and (b) even implements .irq_ack().
We were missing IRQs here.
- Fix the error path for acpi_dev_gpio_irq_get()
- Fix a memory leak in the MXS driver.
- Fix an annoying typo in the STMPE driver.
- Put a dependency on sysfs to the mockup driver"
* tag 'gpio-v4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mpc8xxx: Correct irq handler function
gpio: ath79: Fix module autoload
gpio: ts4800: Fix module autoload
gpio: GPIO_GET_LINEEVENT_IOCTL: Reject invalid line and event flags
gpio: GPIO_GET_LINEHANDLE_IOCTL: Reject invalid line flags
gpio: GPIOHANDLE_GET_LINE_VALUES_IOCTL: Fix information leak
gpio: GPIO_GET_LINEEVENT_IOCTL: Validate line offset
gpio: GPIOHANDLE_GET_LINE_VALUES_IOCTL: Fix information leak
gpio: GPIO_GET_LINEHANDLE_IOCTL: Validate line offset
gpio: GPIO_GET_CHIPINFO_IOCTL: Fix information leak
gpio: GPIO_GET_CHIPINFO_IOCTL: Fix line offset validation
gpio / ACPI: fix returned error from acpi_dev_gpio_irq_get()
gpio: mockup: add sysfs dependency
gpio: stmpe: || vs && typo
gpio: mxs: Unmap region obtained by of_iomap
gpio/board.txt: point to gpiod_set_value
i.MX6UL does only require three clocks to enable CAAM module.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update documentation to reflect the changes made to support IRQ safe PM
domains.
Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The text states that default-input is an endpoint property, but in the
example it is a device property.
The default input is a property of the chip, not of a particular port, so
the example makes more sense.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to multi codec, as the msm8916 codec is now
split into two codecs, Analog and Digital.
Also update the bindings and example to show that the card supports
multicodec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes capture-dai property which should not have existed
in this document in the first place. It looks like leftover from old
version of patches by mistake.
Remove it to avoid any confusion in future.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "rt5668" codec supported in this driver is actually a revision
of "rt5663". So the patch is renamed to "rt5663 v2"
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have the new helper function that sets nice names for GPIO
lines based on "gpio-line-names" device property, we can take advantage of
this in acpi_gpiochip_add().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hogging means that the GPIO controller can "hog" and configure certain
GPIOs without need for a driver or userspace to do that. This is useful in
open-connected boards where BIOS cannot possibly know beforehand which
devices will be connected to the board.
This adds GPIO hogging mechanism to ACPI analogous to Device Tree.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make it possible to have an empty GPIOs in a GPIO list for device. For
example a SPI master may use both GPIOs and native pins as chip selects and
we need to be able to distinguish between the two.
This makes it mandatory to have exactly 3 arguments for GPIOs and then
converts gpiolib to use of __acpi_node_get_property_reference() instead. In
addition we make acpi_gpio_package_count() to handle holes as well (this
matches the DT version).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pin configuration and multiplexing should be preferred now,
even though we still support the old one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dvb/ and video4linux/ dirs were removed, as now, all media
documentation is under media/.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those files got moved to Documentation/process, but as they're very
well known files, add pointers to their new locations.
PS.: I opted to not merge this patch with the previous one
in order to make the diff of the previous one more consistent,
as it will show only renames.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Place README, REPORTING-BUGS, SecurityBugs and kernel-parameters
on an user's manual book.
As we'll be numbering the user's manual, remove the manual
numbering from SecurityBugs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add several documents to the development-process ReST book.
As we don't want renames, use symlinks instead, keeping those
documents on their original place.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we'll type this a lot, after adding CodingStyle & friends,
let's rename the directory name to a shorter one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sphinx doesn't like nested tables on the LaTex output.
So, change the table there to be displayed properly at
the PDF output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document section markups;
- use quote blocks where needed;
- adjust spaces and blank lines;
- add it to the development-processs book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Probably, unicode is something that we might remove from the
docs, as all modern systems support it. Yet, this chapter
is fun, as it mentions support for the Klington fictional
charset ;)
On the other hand, I bet all other OS user manuals
explicit mention unicode support.
So, convert it to ReST and include it at the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use a table for the valid commands;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Add a document title;
- use quote blocks where needed;
- convert parameters to a nested table;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- replace _foo_ by **foo**;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Add a document title;
- use .. note:: markup;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- replace _foo_ by **foo**;
- while here, remove whitespaces at the end of paragraph;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use quote blocks where needed;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix document title;
- use quote blocks where needed;
- use .. note:: for notes;
- use monotonic fonts for config options and file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix identatio for the document title;
- remove its index;
- create a table for hash algorithm to be used;
- use quote blocks where needed;
- use monotonic fonts for parameters;
- adjust whitespaces and blank lines;
- Fix case on section titles;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- add a title for the document;
- convert some parameters to tables;
- use quote blocks where needed;
- use monotonic fonts for parameters;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- add a title for the document;
- convert the table;
- use quote block for the changelog;
- use monotonic fonts for file names;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- use a quote blocks where needed;
- use ``foo`` for monotonic;
- adjust whitespaces and blank lines;
- fix the second list (that starts with 0, instead of A)
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- use a quote blocks where needed;
- fix the chapter/section/subsection markups;
- use ``foo`` for monotonic;
- use .. note:: for /sbin/init file permissions;
- adjust whitespaces and blank lines;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- use a quote blocks where needed;
- fix the chapter/section/subsection markups;
- use ``foo`` for monotonic;
- use .. note:: for the line-range note;
- cleanup whitespaces;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- use a quote block for the big device major/minor list;
- use tables for the other device tables;
- fix the chapter/section/subsection markups;
- use ``foo`` for monotonic;
- use .. attention:: for the attention note to developers;
- use cross-references where needed;
- cleanup whitespaces;
- add it to the user's book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Add a document title and remove its own index;
- use monotonic fonts for paths;
- use quote blocks where needed;
- adjust/use spaces to properly format paragraphs;
- add it to the user book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix identation for the document title;
- use monotonic fonts for paths;
- use quote blocks where needed;
- adjust spaces to properly format paragraphs;
- use :menuselection: and :kbd: for the menu item and keys;
- point too the right item at the menu;
- add it to the user book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix identation for the document title;
- use monotonic fonts for paths;
- use quote blocks where needed;
- adjust spaces to properly format paragraphs;
- use :menuselection: for the menu item;
- add it to the user book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- Fix identation for the document title;
- use monotonic fonts for commands, paths, etc;
- use quote blocks where needed;
- adjust spaces to properly format paragraphs;
- add it to the user book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert it to ReST markup and add it to the user book:
- Add a title to the document;
- touch spaces/new lines to fix Sphinx format;
- use ``foo`` for commands;
- use quote blocks where needed;
- add it to the user book;
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- promote the section level of the document name;
- add/remove spaces/new lines where needed to format the output;
- use quote blocks.
- add it to the user book.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adjust the file for it to be parsed by Sphinx:
- adjust the document title to be parsed;
- use :: for quote blocks;
- fix the horizontal bar markup;
- lower case the TODO title.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert adding-syscalls.txt to ReST markup and add it to the
development-process book:
- add extra lines to make Sphinx to correctly parse paragraphs;
- use quote blocks for examples;
- use monotonic font for dirs, function calls, etc;
- mark manpage pages using the right markup;
- add cross-reference to SubmittingPatches.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
-----BEGIN PGP SIGNATURE-----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=ZRUt
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.10 cycle.
Fair number of outreachy related patches in here. Some of these may well
have already been picked up by Greg but git will sort that out for us.
Also some good staging cleanup work from other sources. Thanks Brian and Lars
in particular for this.
New device support
* ACCES 104-quad-8
- New driver for this 8 channel encoder input board. Lots of new ABI with
this one.
* AD7766
- New driver supporting AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1 and
AD7767-2 24 bit ADCs.
* dmard 10
- New driver for this 3 axis accelerometer.
* Honeywell ABP pressure sensors.
- New driver covering 56 parts in this series (too many to list here!)
* HTS221
- New driver to support this relative humidiy and temperature device.
* LMP91000
- New driver for this potentiostat (form of chemical sensor). Nice example
of use of the buffered consumer interfaces and the use of a consumer
provided trigger.
* MiraMEMS DA311
- New driver for this 3 axis accelerometer.
* MiraMEMS DA280
- New driver for this 3 axis accelerometer. Follow up caught up with
vendor prefixes for these.
Staging graduations
* isl29018 light sensor
- Fixes and cleanups listed below (thanks for your hard work on this Brian!)
* sca3000
- Fixes and cleanups listed below. This was one of the small set of drivers
that went into staging when IIO was first added. Turns out it had a few
bugs and needed to be brought into the modern era! Not clear if I am
the only person who actually has one of these still wired to a board.
New features (Core)
- Add an iio_trigger_validate_own_device helper which relies on the device
and trigger having the same parent. Convenient to have this for some
of the more complex trigger / device interactions. Was hand rolled in
a few drivers already so good to bring it into the core.
- Add an iio_read_channel_offset in kernel access helper (similar to
the existing one for scale).
- IIO_ATTR_{RO, WO, RW} and IIO_DEVICE_ATTR_{RO, WO, RW} macros. These
lead some rather contrived function naming, but there is no denying they
do reduced boilerplate. I'm going to resist their introduction in
drivers 'unless' they form part of a larger set of cleanups.
- Counter channel type and index type.
New features (Drivers)
* hdc100x
- Triggered buffer support.
* mcp4725
- Device tree bindings and support.
- Voltage reference selection.
* ti-adc0832
- Triggered buffer support.
* ti-adc161s626
- Add regulator support allowing _scale and _offset values to be established
and exported.
New features (Tools)
* iio_generic_buffer
- -A option to force enable all channels rather than faulting if some are
already enabled (like -a does). Followup patches tidied this support up.
Cleanups (Core)
- Use kmalloc_array in iio_scan_mask_set.
- Take event_attrs field of iio_info structure constant
- Staging todo list updates. Most of it was long done.
- MAINTAINERS had a wrong directory listing.
Cleanups (Drivers)
* Missing i2c trivial devices entries.
* ad5592r
- Fix an endian type related sparse warnings.
* ad7150
- Constify the event attribute_group structures.
* ad7152
- Add some blank lines to improve readability.
- Sampling frequency control via chan-info element rather than hand rolled
attributes.
- add a new lock to avoid use of mlock for non state change related locking.
* ad7280
- Constify atrribute_group structure (second patch covers the event ones)
* ad7606 (Lars is driving most of the cleanup on this with some additions from
Eva)
- Fix improper setting of oversampling pins. This has been broken a very
long time in this staging driver, so not going to push this back to stable.
- Implement oversampling configuration via the chan_info mask element.
- Remove an unused int_vref_mv field.
- Remove a reundant name field from ad7606_chip_info.
- Remove default device configuration from platform_data in favour of
whatever the power on defaults are.
- Remove out of band error reporting in the kernel log as not providing
much information.
- Fix oversampling ratio by having 1 be the value for no oversampling.
- Avoid allocating buffer for each data capture.
- Factor out common code between periodic and one-shot capture.
- Move set_drvdat into common code.
- Let the common probe function return int rather than jumping through
an ERR_PTR.
- Pass struct device * into common remove to simplify code.
- Always run trigger handler only once per event (no one can remember why
it was being possibly done twice).
- Move over to the GPIO descriptor API to shorten and clarify code.
- Move the buffer code into the main file as it's not optional and is
now rather short in this driver.
- Fix the naming of the supply regulator.
- Rework regulator handling to handle errors including deferred probing.
- Tidy up a ptr_err or 0 return.
* ad7746
- Sampling frequency control via info_mask element rather than hand rolled
* ad7758
- Sampling frequency control via info_mask element rather than hand rolled
attributes.
* ad7816
- Constify the event attribute_group structure.
* adt7316
- Constify the event attribute group structures.
* ak8974
- Cleanup some sparse warnings about endian types.
* ak8975
- Cleanup some sparse warnings about endian types.
* bmi160
- Spare endian warning cleanups.
* isl29018 (towards staging graduation)
- Remove unusedvariables and defines.
- Improve consistency of error handling.
- Signed / unsigned comparison fixes.
- Use the IIO_DEVICE_ATTR_{RO, RW} macros
- Fix a race in in_illuminance_scale_available_show.
- Cleanup exit points of _read_raw
- Sanity check if in suspended state during a write_raw call as was already
done for read_raw.
- Document device tree bidnings.
- Document infrared supression controls.
- Add some newlines to improve readability and drop one that shouldn't be
there.
- Fix a poorly named functions name.
- Fix multiline coment syntax.
- Tidy up a pair or return statements by unifying them.
- Rename description in Kconfig for consistency with similar drivers.
* lidar
- cleanup power management by dropping unnecessary call.
* ltr501
- Use the claim_direct_mode helpers. Fix a race condition along the way.
* max1027
- Fix a dubious x | !y sparse warning.
- Use the new iio_trigger_validate_own_device helper.
* max440000
- Clean up some sparse warnings about endian types.
* mcp4725
- Use the regulator framework to establish the reference voltage rather than
getting it from platform data.
- Tidy up a comment typo.
- Fix a wrong PTR_ERR query (wrong regulator).
* mma7660
- Take a mma7660_nscale static.
* mma8452
- Use the new iio_trigger_validate_own_device helper.
- Use claim_direct_mode helpers - fix a race condition along the way.
* mpl3115
- Use claim_direct_mode helpers - fix a race condition along the way.
* ms65611
- Tidy up regulator error handling and clean out a static warning in the mix.
* sca3000
- Avoid a potential unitialized variable if a hardware read returns a value
that isn't actually supported (mostly warning supression).
- Fix a use before setting of the indio_dev->buffer pointer. Broken for
a very long time so not going to rush this into stable.
- Merge buffer file with core file. We used to always split these.
Sometimes it's just not worth the hassle. In this case the device's main
feature is it's hardware fifos so unlikely anyone would want to run it
without.
- Drop the sca3000_register_ring_funcs function as it's a pointless wrapper
once we have only one file.
- Fix cleaning of flag + setting of size of scan. Without this you can't
start the buffer twice and expect sensible (or any) results. Again,
broken for a long time so not heading for stable.
- Drop the custom watershed setting ABI - for now we'll just support one
value.
- Move to a hybrid hard / soft buffer design (how we've been doing it
for similar devices for a while now!)
- Cleanup some unusued variables.
- Use a fake channel to support core handling of freefall event registration.
- Cleanup the register defines.
- Fix an off by one error in axis due to IIO_NO_MOD taking up the 0 value.
Been broken since first admission of IIO to the staging tree.
- Add readback of the 3db low pass filter frequency and later writing
allowing droppign of custom measurement mode attributes as they can
be represented by the filter choices that is their main characteristic.
- Drop non standard revision attr and replace with dev_info on probe.
- Avoid a race in probe.
- Various formatting fixes.
- Kernel-docify docs that were very nearly in the write format.
* tsl2583
- Constify attribute_group structure.
* zpa2326
- Drop a redundant DEBUG ifdef.
Cleanups (Tools)
* iio_generic_buffer
- Fix the ? arguement. Previously it sort of worked as you got the help
message as a result of it not recognising the arguement.
Instead of using codeblock for the cardlists, use tables, in
order to improve their visual when presenting them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some entries are out of order.
While here, clear spaces/tabs.
The content remains the same, with the exeption of one duplicated
entry from the same driver, where two different brand names share
the same entry. The content of such cell was merged, using a
comma.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I was on vacation during the merge window (a long vacation)
but this is a bug fix that should go in and a new driver that shouldn't
hurt anything.
This has been in linux-next for a month or so.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlgKVpoACgkQIXnXXONXERdGBACeONBS0wOf4Rv+bxSOdeJcTwLJ
rmoAoJ2R0BpWE1imvcC+AqXOoqg2c48k
=P4Dz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A small bug fix and a new driver for acting as an IPMI device.
I was on vacation during the merge window (a long vacation) but this
is a bug fix that should go in and a new driver that shouldn't hurt
anything.
This has been in linux-next for a month or so"
* tag 'for-linus-4.9-2' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: fix crash on reading version from proc after unregisted bmc
ipmi/bt-bmc: remove redundant return value check of platform_get_resource()
ipmi/bt-bmc: add a dependency on ARCH_ASPEED
ipmi: Fix ioremap error handling in bt-bmc
ipmi: add an Aspeed BT IPMI BMC driver
Add ABI documentation from the ISL29018 Data Sheet (FN6619.4, Oct 8,
2012) about the infrared suppression that can be controlled
with the proximity_on_chip_ambient_infrared_suppression sysfs attribute.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add OX820 bindings and remove clock indices from bindings since they are present
in the dt-bindings headers files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20161005150752.22618-7-narmstrong@baylibre.com
Pull timer updates from Thomas Gleixner:
"This updates contains:
- A revert which addresses a boot failure on ARM Sun5i platforms
- A new clocksource driver, which has been delayed beyond rc1 due to
an interrupt driver issue which was unearthed by this driver. The
debugging of that issue and the discussion about the proper
solution made this driver miss the merge window. There is no point
in delaying it for a full cycle as it completes the basic mainline
support for the new JCore platform and does not create any risk
outside of that platform"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "clocksource/drivers/timer_sun5i: Replace code by clocksource_mmio_init"
clocksource: Add J-Core timer/clocksource driver
of: Add J-Core timer bindings
Pull vmap stack fixes from Ingo Molnar:
"This is fallout from CONFIG_HAVE_ARCH_VMAP_STACK=y on x86: stack
accesses that used to be just somewhat questionable are now totally
buggy.
These changes try to do it without breaking the ABI: the fields are
left there, they are just reporting zero, or reporting narrower
information (the maps file change)"
* 'mm-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm: Change vm_is_stack_for_task() to vm_is_stack_for_current()
fs/proc: Stop trying to report thread stacks
fs/proc: Stop reporting eip and esp in /proc/PID/stat
mm/numa: Remove duplicated include from mprotect.c
Add NAND driver to support the Oxford Semiconductor OX820 NAND Controller.
This is a simple memory mapped NAND controller with single chip select and
software ECC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYCpJqAAoJEFHr6jzI4aWABS8QAJXuCjXrfNdQoiNmSHTOOUuj
Z1KFIU/WjLa42VD2KIvW/OiTjzmrA9yl/PkNYD185yXu5DAE1h+lH0gBCA3KlSUc
LwNneqn+3aGqmAX7jTm1HaWFCQt6mF0z3hwDPvEXhC4hcNjhe3mp3Q9/Q8idVfAJ
f48vBa8qgJ5gpD5zVva5ujh1F2RUA+RQmhaR+LS19B+OH6xPzRp7VGUdsKRp75pI
ILVCsjxA+DoaMOUK9quE5/9n9IK+N10QLfCqJu6HxJJ47nBxkiDPtdcndv0WTA9m
kYTdqcv5o7A4+SrdXOkNBBHjj09UhdHBmhIrEt6286wyJ3thvDIhjMrX6OwJSCyb
oB8PhXwjyUQrws19h4RNDToPG2Hr9A8BXVTofyPV4ku6gvucI03WFcVbHMWhAiLh
lwR3Ppg4mHHAndL4oRlRhpvEVmBGwMuKEbisTa82T5RK4iPVWRcGqN6bltj9g6QX
VXc8KQzKM+qEKQmDzdjExr0ZFq+USea96JmCJs6l9+M1nwe5CRCJAZyjp5LhVYRf
ky9DSmp+nwIUxAQ73rv/NrjvRNZXCaUn4G+vpcSix7jrq6DqJoLSTEqpfw3Lfejj
oJ1YxqD9SrNYhXChj071zLoDznZIviCxitLbQYVLt1Y72iLUXgt+s/y3JZWuxGrt
EAmIXJq8fJHhHEd0TEW9
=39+z
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Prevent unlikely crash in copro_calculate_slb() (Frederic Barrat)
- cxl: Prevent adapter reset if an active context exists (Vaibhav Jain)
Fixes for code merged this cycle:
- Fix boot on systems with uncompressed kernel image (Heiner Kallweit)
- Drop dump_numa_memory_topology() (Michael Ellerman)
- Fix numa topology console print (Aneesh Kumar K.V)
- Ignore the pkey system calls for now (Stephen Rothwell)"
* tag 'powerpc-4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Ignore the pkey system calls for now
powerpc: Fix numa topology console print
powerpc/mm: Drop dump_numa_memory_topology()
cxl: Prevent adapter reset if an active context exists
powerpc/boot: Fix boot on systems with uncompressed kernel image
powerpc/mm: Prevent unlikely crash in copro_calculate_slb()
Perform a relatively simple conversion of vme_api.txt to reStructuredText
and move under driver-api, which seems the most logical place for this
documentation.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fix a spelling typo in cciss.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update UIO documentation to include basic information about
uio_hv_generic.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fix spelling typos in Documentation/device-mapper/dm-raid.txt.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Current uprobetracer examples don't work as they use an incorrect syntax
- if no event name is specified then 'p/r' must not be followed by a
colon
- if no event name is specified then the default event name will have a
'p_' prefix, so use that in the '-' example as well
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update DT bindings to describe idle states of PM domains.
This patch is based on the original patch by Marc Titinger.
Signed-off-by: Marc Titinger <mtitinger+renesas@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PID tuning is not available when the get_target_pstate_use_cpu_load()
is used to calculate target_state. So update the documentation.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Describe the hsv_enc field and its use.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My initials were on the Changelog, but there was no link to my name.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
MK808 is a tv stick which has rockchip rk3066 CPU inside, two usb ports
- host and otg, micro sd card slot and onboard wifi RK901.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix compilation warning in xt_hashlimit on m68k 32-bits, from
Geert Uytterhoeven.
2) Fix wrong timeout in set elements added from packet path via
nft_dynset, from Anders K. Pedersen.
3) Remove obsolete nf_conntrack_events_retry_timeout sysctl
documentation, from Nicolas Dichtel.
4) Ensure proper initialization of log flags via xt_LOG, from
Liping Zhang.
5) Missing alias to autoload ipcomp, also from Liping Zhang.
6) Missing NFTA_HASH_OFFSET attribute validation, again from Liping.
7) Wrong integer type in the new nft_parse_u32_check() function,
from Dan Carpenter.
8) Another wrong integer type declaration in nft_exthdr_init, also
from Dan Carpenter.
9) Fix insufficient mode validation in nft_range.
10) Fix compilation warning in nft_range due to possible uninitialized
value, from Arnd Bergmann.
11) Zero nf_hook_ops allocated via xt_hook_alloc() in x_tables to
calm down kmemcheck, from Florian Westphal.
12) Schedule gc_worker() to run again if GC_MAX_EVICTS quota is reached,
from Nicolas Dichtel.
13) Fix nf_queue() after conversion to single-linked hook list, related
to incorrect bypass flag handling and incorrect hook point of
reinjection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the MT21C documentation, making it clearer that this format
requires the MDP for further processing.
Also fix the fourcc (it was a fivecc :-) )
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a DT binding documentation of MDP for the MT8173 SoC
from Mediatek
Signed-off-by: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds compatible for SoCs which use clockgen, the SoCs are LS1043A,
LS1046A, LS2080A.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"nxp,pcf2127" and "nxp,pcf2129" are I2c devices, adds them to the list
of trivial i2c devices.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
SCFG and DCFG are SoC-specific devices can be found on SoCs like LS1021A,
LS1043A and LS1046A, this patch updates bindings for SCFG and DCFG to
reflect more SoCs.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds SoC compatible for LS1043A and LS2080A which are supported, and
for LS1046A which is going to be supported.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a DT binding documentation of Video Decoder for the
MT8173 SoC from Mediatek.
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add device tree bindings file for the cs35l34 8V boosted
class D amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commits add missing fields in the documentation that are used
by the new device variant. It also includes DT example to show how
the variant should be used.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This commits adds a vendor for the company INSIDE Secure.
See https://www.insidesecure.com, for more details.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The A31's display pipeline has 2 frontends, 2 backends, and 2 TCONs. It
also has new display enhancement blocks, such as the DRC (Dynamic Range
Controller), the DEU (Display Enhancement Unit), and the CMU (Color
Management Unit). It supports HDMI, MIPI DSI, and 2 LCD/LVDS channels.
The A31s display pipeline is almost the same, just without MIPI DSI.
Only the TCON seems to be different, due to the missing mux for MIPI
DSI.
Add compatible strings for both of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 TCON has mux controls for how TCON outputs are routed to the
HDMI and MIPI DSI blocks.
Since the A31s does not have MIPI DSI, it only has a mux for the HDMI
controller input.
This patch only adds support for the compatible strings. Actual support
for the mux controls should be added with HDMI and MIPI DSI support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 and A31s also have the DRC as part of the display pipeline.
As we know virtually nothing about them, just add compatible strings
for both SoCs to the stub driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
gpiod_set_value() is preffered interface these days, so add a
pointer. Also fix a missing ).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[Fixed some grammar and reworded]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new compatible string for reset and sys-ctrl for the Oxford
Semiconductor OX820 Support.
Drop the OX810SE indices since they moved in a dedicated include file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt softreset bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Update with brief overview and reference for more detailed
arch design documents.
Add new section for Intel GVT-g host support.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This reverts more of:
b76437579d ("procfs: mark thread stack correctly in proc/<pid>/maps")
... which was partially reverted by:
65376df582 ("proc: revert /proc/<pid>/maps [stack:TID] annotation")
Originally, /proc/PID/task/TID/maps was the same as /proc/TID/maps.
In current kernels, /proc/PID/maps (or /proc/TID/maps even for
threads) shows "[stack]" for VMAs in the mm's stack address range.
In contrast, /proc/PID/task/TID/maps uses KSTK_ESP to guess the
target thread's stack's VMA. This is racy, probably returns garbage
and, on arches with CONFIG_TASK_INFO_IN_THREAD=y, is also crash-prone:
KSTK_ESP is not safe to use on tasks that aren't known to be running
ordinary process-context kernel code.
This patch removes the difference and just shows "[stack]" for VMAs
in the mm's stack range. This is IMO much more sensible -- the
actual "stack" address really is treated specially by the VM code,
and the current thread stack isn't even well-defined for programs
that frequently switch stacks on their own.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux API <linux-api@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tycho Andersen <tycho.andersen@canonical.com>
Link: http://lkml.kernel.org/r/3e678474ec14e0a0ec34c611016753eea2e1b8ba.1475257877.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Python module names should not have hyphens per [PEP 8]. Drop the hyphen
from kernel-doc.py. The extension directive remains unchanged.
[PEP 8] https://www.python.org/dev/peps/pep-0008/#package-and-module-names
Reported-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
I made a mistake as for naming for this block. The MIO block is not
implemented for these 3 SoCs in the first place. The current naming
will be a trouble if an SoC with both MIO and SD-ctrl blocks appear
in the future.
This driver has just been merged in the previous merge window.
Rename it before the release.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Rename ns2.txt to brcm,ns2.txt to match naming convention followed
by rest of Broadcom binding documentation.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the spelling mistakes and extra and statements in the sentences.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding a new binding for qcom,hidma-1.1 to distinguish HW supporting
MSI interrupts from the older revision.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The AUO T215HVN01 is a 21.5" FHD (1920x1080) color TFT LCD panel.
This panel is used on the Acer Chromebase 21.5-inch All-in-One (DC221HQ).
Link to spec: http://www.udmgroup.com/ftp/T215HVN01.0.pdf
v2: fix alphabetical order
v3: remove minor revision suffix ".0" and add link to spec
v4: add dt-binding documentation
Signed-off-by: Haixia Shi <hshi@chromium.org>
Tested-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp 15" LQ150X1LG11 panel is an XGA TFT LCD panel.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch prevents resetting the cxl adapter via sysfs in presence of
one or more active cxl_context on it. This protects against an
unrecoverable error caused by PSL owning a dirty cache line even after
reset and host tries to touch the same cache line. In case a force reset
of the card is required irrespective of any active contexts, the int
value -1 can be stored in the 'reset' sysfs attribute of the card.
The patch introduces a new atomic_t member named contexts_num inside
struct cxl that holds the number of active context attached to the card
, which is checked against '0' before proceeding with the reset. To
prevent against a race condition where a context is activated just after
reset check is performed, the contexts_num is atomically set to '-1'
after reset-check to indicate that no more contexts can be activated on
the card anymore.
Before activating a context we atomically test if contexts_num is
non-negative and if so, increment its value by one. In case the value of
contexts_num is negative then it indicates that the card is about to be
reset and context activation is error-ed out at that point.
Fixes: 62fa19d4b4 ("cxl: Add ability to reset the card")
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a workaround for mainstone, idp and stargate2 boards, for u16 writes
which must be aligned on 32 bits addresses.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TOPEET itop Exynos4412 has three versions of base boards. The
Elite version is the cheap one without too much peripheral devices
on it.
Currently supported are serial console, wired networking (USB), USB OTG
in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC
and LEDs. The WM8960 analog audio codec is also enabled.
The FIMC is not used for camera currently, I enabled it just for a
colorspace converter.
Signed-off-by: Randy Li <ayaka@soulik.info>
Acked-by: Rob Herring <robh@kernel.org>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The queue limits already have a 'chunk_sectors' setting, so
we should be presenting it via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: Updated Documentation/ABI/testing/sysfs-block]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add the zoned queue limit to indicate the zoning model of a block device.
Defined values are 0 (BLK_ZONED_NONE) for regular block devices,
1 (BLK_ZONED_HA) for host-aware zone block devices and 2 (BLK_ZONED_HM)
for host-managed zone block devices. The standards defined drive managed
model is not defined here since these block devices do not provide any
command for accessing zone information. Drive managed model devices will
be reported as BLK_ZONED_NONE.
The helper functions blk_queue_zoned_model and bdev_zoned_model return
the zoned limit and the functions blk_queue_is_zoned and bdev_is_zoned
return a boolean for callers to test if a block device is zoned.
The zoned attribute is also exported as a string to applications via
sysfs. BLK_ZONED_NONE shows as "none", BLK_ZONED_HA as "host-aware" and
BLK_ZONED_HM as "host-managed".
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Nexbox is an IPTV set-top-box distributor, mainly with Amlogic SoCs:
https://www.inexbox.com
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add documention of ti,min-output-impedance and ti,max-output-impedance
which can be used to correct MAC impedance mismatch using phy extended
registers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the DT binding documentation for the FDMA constroller
found on STi based chipsets from STMicroelectronics.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This binding was deprecated due to commit aa381a7259 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization"). However that
commit is now reverted, so also revert this commit.
The binding is valid and shouldn't be deprecated.
This reverts commit 65e1ff7f4b ("Documentation: devicetree: dwc2:
Deprecate g-tx-fifo-size").
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Various pieces of information about DRM formats (number of planes, color
depth, chroma subsampling, ...) are scattered across different helper
functions in the DRM core. Callers of those functions often need to
access more than a single parameter of the format, leading to
inefficiencies due to multiple lookups.
Centralize all format information in a data structure and create a
function to look up information based on the format 4CC.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476744081-24485-2-git-send-email-laurent.pinchart@ideasonboard.com
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt softreset bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
STiH415/6 SoC support is being removed from the kernel.
This patch updates the sti dt powerdown bindings and
removes references to these obsolete platforms.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <p.zabel@pengutronix.de>
Cc: <robh+dt@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
STiH415/6 SoC's are being removed from the kernel. This
patch removes the compatibles from the dt doc and also
updates the example to a supported platform.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <rui.zhang@intel.com>
Cc: <edubezval@gmail.com>
Cc: <robh+dt@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
This platform is being removed from the kernel so remove
the dt example.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <tj@kernel.org>
Cc: <robh+dt@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Now that eagerfpu= is gone, remove it from the docs and some
comments. Also sync the changes to tools/.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/cf430dd4481d41280e93ac6cf0def1007a67fc8e.1476740397.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
dm-raid 1.9.0 fails to activate existing RAID4/10 devices that have the
old superblock format (which does not have takeover/reshaping support
that was added via commit 33e53f0685).
Fix validation path for old superblocks by reverting to the old raid4
layout and basing checks on mddev->new_{level,layout,...} members in
super_init_validation().
Cc: stable@vger.kernel.org # 4.8
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This entry has been removed in commit 9500507c61.
Fixes: 9500507c61 ("netfilter: conntrack: remove timer from ecache extension")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds files and directories to debugfs for controlling and reading frame
CRCs, per CRTC:
dri/0/crtc-0/crc
dri/0/crtc-0/crc/control
dri/0/crtc-0/crc/data
Drivers can implement the set_crc_source callback() in drm_crtc_funcs to
start and stop generating frame CRCs and can add entries to the output
by calling drm_crtc_add_crc_entry.
v2:
- Lots of good fixes suggested by Thierry.
- Added documentation.
- Changed the debugfs layout.
- Moved to allocate the entries circular queue once when frame
generation gets enabled for the first time.
v3:
- Use the control file just to select the source, and start and stop
capture when the data file is opened and closed, respectively.
- Make variable the number of CRC values per entry, per source.
- Allocate entries queue each time we start capturing as now there
isn't a fixed number of CRC values per entry.
- Store the frame counter in the data file as a 8-digit hex number.
- For sources that cannot provide useful frame numbers, place
XXXXXXXX in the frame field.
v4:
- Build only if CONFIG_DEBUG_FS is enabled.
- Use memdup_user_nul.
- Consolidate calculation of the size of an entry in a helper.
- Add 0x prefix to hex numbers in the data file.
- Remove unnecessary snprintf and strlen usage in read callback.
v5:
- Made the crcs array in drm_crtc_crc_entry fixed-size
- Lots of other smaller improvements suggested by Emil Velikov
v7:
- Move definition of drm_debugfs_crtc_crc_add to drm_internal.h
v8:
- Call debugfs_remove_recursive when we fail to create the minor
device
v9:
- Register the debugfs directory for a crtc from
drm_crtc_register_all()
v10:
- Don't let debugfs failures interrupt CRTC registration (Emil
Velikov)
v11:
- Remove extra brace that broke compilation. Sorry!
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1475767268-14379-3-git-send-email-tomeu.vizoso@collabora.com
For mac80211_hwsim interfaces, suggest to use wpa_supplicant with the more
modern, netlink based driver instead of wext.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for RZ/G1M (R8A7743) SoC power areas to the R-Car SYSC driver.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI/BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools.
Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and networking
tests from Documentation to selftests.
Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay, and
blackfin examples from Documentation to samples.
Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
Deletes BUILD_DOCSRC and its dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=60kH
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools:
* Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and
networking tests from Documentation to selftests.
* Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay,
and blackfin examples from Documentation to samples.
* Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
* Deletes BUILD_DOCSRC and its dependencies"
* tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (21 commits)
selftests/futex: Check ANSI terminal color support
Doc: update 00-INDEX files to reflect the runnable code move
samples: move blackfin gptimers-example from Documentation
tools: move pcmcia crc32hash tool from Documentation
tools: move laptops dslm tool from Documentation
tools: move accounting tool from Documentation
samples: move auxdisplay example code from Documentation
samples: move watchdog example code from Documentation
samples: move timers example code from Documentation
samples: move misc-devices/mei example code from Documentation
samples: move mic/mpssd example code from Documentation
selftests: Move networking/timestamping from Documentation
selftests: move watchdog tests from Documentation/watchdog
selftests: move ia64 tests from Documentation/ia64
selftests: move vDSO tests from Documentation/vDSO
selftests: move ptp tests from Documentation/ptp
selftests: move prctl tests from Documentation/prctl
selftests: move dnotify_test from Documentation/filesystems
selftests/timers: Add missing error code assignment before test
selftests/zram: replace ZRAM_LZ4_COMPRESS
...
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
Only 32 more to go...
-----BEGIN PGP SIGNATURE-----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=U9Pc
-----END PGP SIGNATURE-----
Merge tag 'docs-4.9-2' of git://git.lwn.net/linux
Pull one more documentation update from Jonathan Corbet:
"A single commit converting the mac80211 DocBook template over to
Sphinx. Only 32 more to go..."
* tag 'docs-4.9-2' of git://git.lwn.net/linux:
docs-rst: sphinxify 802.11 documentation
- Small patch set for hns net driver that the roce patches depend on
- Various fixes to the hns-roce driver
- Add connection manager support to the hns-roce driver
-----BEGIN PGP SIGNATURE-----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=PmmI
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"This merge window was the first where Huawei had to try and coordinate
their patches between their net driver and their new roce driver
(similar to mlx4 and mlx5).
They didn't do horribly, but there were some issues (and we knew that
because they simply didn't know what to do in the beginning). As a
result, I had a set of patches that depended on some patches that
normally would have come to you via Dave's tree. Those patches have
been on netdev@ for a while, so I got Dave to give me his approval to
send them to you. As such, the other 29 patches I had behind them are
also now ready to go.
This catches the hns and hns-roce drivers up to current, and for
future patches we are working with them to get them up to speed on how
to do joint driver development so that they don't have these sorts of
cross tree dependency issues again. BTW, Dave gave me permission to
add his Acked-by: to the patches against the net tree, but I've had
this branch through 0day (but not linux-next since it was off by
itself) and I didn't want to rebase the series just to add Dave's ack
for the 8 patches in the net area.
Updates to the hns drivers:
- Small patch set for hns net driver that the roce patches depend on
- Various fixes to the hns-roce driver
- Add connection manager support to the hns-roce driver"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (36 commits)
IB/hns: Fix for removal of redundant code
IB/hns: Delete the redundant lines in hns_roce_v1_m_qp()
IB/hns: Fix the bug when platform_get_resource() exec fail
IB/hns: Update the rq head when modify qp state
IB/hns: Cq has not been freed
IB/hns: Validate mtu when modified qp
IB/hns: Some items of qpc need to take user param
IB/hns: The Ack timeout need a lower limit value
IB/hns: Return bad wr while post send failed
IB/hns: Fix bug of memory leakage for registering user mr
IB/hns: Modify the init of iboe lock
IB/hns: Optimize code of aeq and ceq interrupt handle and fix the bug of qpn
IB/hns: Delete the sqp_start from the structure hns_roce_caps
IB/hns: Fix bug of clear hem
IB/hns: Remove unused parameter named qp_type
IB/hns: Simplify function of pd alloc and qp alloc
IB/hns: Fix bug of using uninit refcount and free
IB/hns: Remove parameters of resize cq
IB/hns: Remove unused parameters in some functions
IB/hns: Add node_guid definition to the bindings document
...
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
Subsystem:
- delete owner assignment in multiple drivers
- constify rtc_class_ops structures
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with previous
behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJYASBeAAoJENiigzvaE+LCDO4QAJAi0TV2i0vYaJLDWyCGDx3P
cts/Su2JdLgeLxilKvyYgwUpp8fsv681ZaZi+a6Jln/cn0MOcWwJoopiC30CSR8M
9UxmRsFR9Ev/Cm/NZChcsTQwyTHOumnzZzxtnYr0RWOw7s4K68gEQEpWWT7qHTp1
KVwfIvjAIPcozw25QWWGUWHu22PsI38NTH5Bg+rimMCToNbSDFAm+d62cdeIbkJF
FoQIut0/Lh5UZ12+T8l0iBydY3bINeo1SZY5yAwQGRzJBecxRccbtKlnUjXnywke
xAO5KQzegkLPTU4R6ssK/SQfVlDrfG3fkjWNvUEC/Vyw94v2SaFB1XjvlCXwL3mN
XqzWXeestqFvKRjbYsM0NwsPX4+wxjDNq9YaAhpFYDAA9BL3vREB41qf/dCOFywG
tqHBRpwN9g7u/72SLJ3icYdjmpaQIQbLF9wl8LJiPrWn4xwTNVIB2u3APcSuxE7/
q49jD72LyEVhOUyGs0Hev584s4PC2fMoveq52ng0gMVbOtX0A0FJQQMcR2/2DIOp
GLzPVuupx/8Eck9RFdr06Iv74j/bD7tScfiifZt6LfY5c8K7HOYykoskaRz3XMV4
gx7Aajb8+jMVvI2TOthIa/WCXktQ8MBWTMZ6vbCxxpIRPBYuDqKmt1hXsYR5s6ql
fMrn+tWltdRQKGIF2GrR
=ZqqR
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.9
Subsystem:
- delete owner assignment in multiple drivers
- constify rtc_class_ops structures
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with
previous behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection"
* tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (25 commits)
rtc: rv8803: set VDETOFF and SWOFF via device tree
dt/bindings: Add bindings for Micro Crystal rv8803
devicetree: Add Micro Crystal AG vendor id
rtc: cmos: avoid unused function warning
rtc: ac100: Add NULL checking for devm_kzalloc call
rtc: ds1347: changed raw spi calls to register map calls
rtc: cmos: Restore alarm after resume
rtc: cmos: Clear ACPI-driven alarms upon resume
rtc: omap: Support ext_wakeup configuration
rtc: cmos: Initialize hpet timer before irq is registered
rtc: asm9260: rework locking
rtc: asm9260: allow COMPILE_TEST
rtc: constify rtc_class_ops structures
rtc: ac100: support clock-output-names in device tree binding
rtc: rx6110: remove owner assignment
rtc: pic32: Delete owner assignment
rtc: bq32k: Fix handling of oscillator failure flag
rtc: bq32k: Use correct mask name for 'minutes' register.
rtc: sysfs: fix a cast removing the const attribute
Documentation: dt: Intersil isl12057 is not a trivial device
...
Pull more i2c updates from Wolfram Sang:
"A small update pull request from I2C.
This adds one comment to a change we did in this merge window to
handle lockdep better, and pulls in a branch which should have been in
4.8 already improving DT support for I2C"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
gpio: pca953x: add a comment explaining the need for a lockdep subclass
i2c: core: Add support for 'i2c-bus' subnode
dt-bindings: i2c: Add support for 'i2c-bus' subnode
This is just a set of minor updates and fixes which weren't quite ready in
time for the first pull request. The only real thing of note is Mike Christie
is stepping down as Maintainer of iscsi to be replaced by Lee Duncan and Chris
Leech.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bAub
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is just a set of minor updates and fixes which weren't quite
ready in time for the first pull request.
The only real thing of note is Mike Christie is stepping down as
Maintainer of iscsi to be replaced by Lee Duncan and Chris Leech"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Kconfig fix
scsi: g_NCR5380: Stop using scsi_module.c
scsi: g_NCR5380: Reduce overrides[] from array to struct
scsi: g_NCR5380: Remove deprecated __setup
scsi: ufs: Fix error return code in ufshcd_init()
scsi: ufs: Data Segment only needed for WRITE DESCRIPTOR
scsi: cxgb4i: Set completion bit in work request
MAINTAINERS: Update open-iscsi maintainers
scsi: ufs: Enable no vccq quirk for skhynix device
scsi: be2iscsi: mark symbols static where possible
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
Stable bugfixes:
- sunrpc: fix writ espace race causing stalls
- NFS: Fix inode corruption in nfs_prime_dcache()
- NFSv4: Don't report revoked delegations as valid in
nfs_have_delegation()
- NFSv4: nfs4_copy_delegation_stateid() must fail if the delegation is
invalid
- NFSv4: Open state recovery must account for file permission changes
- NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
Features:
- Add support for tracking multiple layout types with an ordered list
- Add support for using multiple backchannel threads on the client
- Add support for pNFS file layout session trunking
- Delay xprtrdma use of DMA API (for device driver removal)
- Add support for xprtrdma remote invalidation
- Add support for larger xprtrdma inline thresholds
- Use a scatter/gather list for sending xprtrdma RPC calls
- Add support for the CB_NOTIFY_LOCK callback
- Improve hashing sunrpc auth_creds by using both uid and gid
Bugfixes:
- Fix xprtrdma use of DMA API
- Validate filenames before adding to the dcache
- Fix corruption of xdr->nwords in xdr_copy_to_scratch
- Fix setting buffer length in xdr_set_next_buffer()
- Don't deadlock the state manager on the SEQUENCE status flags
- Various delegation and stateid related fixes
- Retry operations if an interrupted slot receives EREMOTEIO
- Make nfs boot time y2038 safe
-----BEGIN PGP SIGNATURE-----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=XOrF
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client updates from Anna Schumaker:
"Highlights include:
Stable bugfixes:
- sunrpc: fix writ espace race causing stalls
- NFS: Fix inode corruption in nfs_prime_dcache()
- NFSv4: Don't report revoked delegations as valid in nfs_have_delegation()
- NFSv4: nfs4_copy_delegation_stateid() must fail if the delegation is invalid
- NFSv4: Open state recovery must account for file permission changes
- NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
Features:
- Add support for tracking multiple layout types with an ordered list
- Add support for using multiple backchannel threads on the client
- Add support for pNFS file layout session trunking
- Delay xprtrdma use of DMA API (for device driver removal)
- Add support for xprtrdma remote invalidation
- Add support for larger xprtrdma inline thresholds
- Use a scatter/gather list for sending xprtrdma RPC calls
- Add support for the CB_NOTIFY_LOCK callback
- Improve hashing sunrpc auth_creds by using both uid and gid
Bugfixes:
- Fix xprtrdma use of DMA API
- Validate filenames before adding to the dcache
- Fix corruption of xdr->nwords in xdr_copy_to_scratch
- Fix setting buffer length in xdr_set_next_buffer()
- Don't deadlock the state manager on the SEQUENCE status flags
- Various delegation and stateid related fixes
- Retry operations if an interrupted slot receives EREMOTEIO
- Make nfs boot time y2038 safe"
* tag 'nfs-for-4.9-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (100 commits)
NFSv4.2: Fix a reference leak in nfs42_proc_layoutstats_generic
fs: nfs: Make nfs boot time y2038 safe
sunrpc: replace generic auth_cred hash with auth-specific function
sunrpc: add RPCSEC_GSS hash_cred() function
sunrpc: add auth_unix hash_cred() function
sunrpc: add generic_auth hash_cred() function
sunrpc: add hash_cred() function to rpc_authops struct
Retry operation on EREMOTEIO on an interrupted slot
pNFS: Fix atime updates on pNFS clients
sunrpc: queue work on system_power_efficient_wq
NFSv4.1: Even if the stateid is OK, we may need to recover the open modes
NFSv4: If recovery failed for a specific open stateid, then don't retry
NFSv4: Fix retry issues with nfs41_test/free_stateid
NFSv4: Open state recovery must account for file permission changes
NFSv4: Mark the lock and open stateids as invalid after freeing them
NFSv4: Don't test open_stateid unless it is set
NFSv4: nfs4_do_handle_exception() handle revoke/expiry of a single stateid
NFS: Always call nfs_inode_find_state_and_recover() when revoking a delegation
NFSv4: Fix a race when updating an open_stateid
NFSv4: Fix a race in nfs_inode_reclaim_delegation()
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into next
Sync up with mainline to bring in I2C host notify changes and other
updates.
