QE_General4 should only round up the divisor iff divisor is > 3.
Rounding up lower divisors makes the error too big, causing USB
on MPC832x to fail.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/p3060_qds.c: In function '__machine_initcall_p3060_qds_declare_of_platform_devices':
arch/powerpc/platforms/85xx/p3060_qds.c:73:1: error: implicit declaration of function 'declare_of_platform_devices'
declare_of_platform_devices should have been corenet_ds_publish_devices.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver for the Freescale P3060 QDS got added by commit 96cc017c5b
("[...] Add support for P3060QDS board"). Its Kconfig entry selects
MPC8xxx_GPIO. But at the time that driver got added MPC8xxx_GPIO was
already renamed to GPIO_MPC8XXX, by commit c68308dd50 ("gpio: move
mpc8xxx/512x gpio driver to drivers/gpio").
So make this driver select GPIO_MPC8XXX.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers. As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).
IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
altroot support has been gone for years, along with arch/*/asm/namei.h;
looks like a dummy survivor that sat it out in microblaze tree...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (86 commits)
ipv4: fix redirect handling
ping: dont increment ICMP_MIB_INERRORS
sky2: fix hang in napi_disable
sky2: enforce minimum ring size
bonding: Don't allow mode change via sysfs with slaves present
f_phonet: fix page offset of first received fragment
stmmac: fix pm functions avoiding sleep on spinlock
stmmac: remove spin_lock in stmmac_ioctl.
stmmac: parameters auto-tuning through HW cap reg
stmmac: fix advertising 1000Base capabilties for non GMII iface
stmmac: use mdelay on timeout of sw reset
sky2: version 1.30
sky2: used fixed RSS key
sky2: reduce default Tx ring size
sky2: rename up/down functions
sky2: pci posting issues
sky2: fix hang on shutdown (and other irq issues)
r6040: fix check against MCRO_HASHEN bit in r6040_multicast_list
MAINTAINERS: change email address for shemminger
pch_gbe: Move #include of module.h
...
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Suspend: Fix bug in suspend statistics update
PM / Hibernate: Fix the early termination of test modes
PM / shmobile: Fix build of sh7372_pm_init() for CONFIG_PM unset
PM Sleep: Do not extend wakeup paths to devices with ignore_children set
PM / driver core: disable device's runtime PM during shutdown
PM / devfreq: correct Kconfig dependency
PM / devfreq: fix use after free in devfreq_remove_device
PM / shmobile: Avoid restoring the INTCS state during initialization
PM / devfreq: Remove compiler error after irq.h update
PM / QoS: Properly use the WARN() macro in dev_pm_qos_add_request()
PM / Clocks: Only disable enabled clocks in pm_clk_suspend()
ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix
PM / shmobile: Don't skip debugging output in pd_power_up()
Prevent tracing of preempt_disable() in get_cpu_var() in
kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled,
preempt_disable/enable() are traced and this causes the function_graph
tracer to go into an infinite recursion. By open coding the
preempt_disable() around the get_cpu_var(), we can use the notrace
version which prevents preempt_disable/enable() from being traced and
prevents the recursion.
Based on a similar patch for Xen from Jeremy Fitzhardinge.
Tested-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
random: Fix handing of arch_get_random_long in get_random_bytes()
x86: Call stop_machine_text_poke() on all CPUs
x86, ioapic: Only print ioapic debug information for IRQs belonging to an ioapic chip
x86/mrst: Avoid reporting wrong nmi status
x86/mrst: Add support for Penwell clock calibration
x86/apic: Allow use of lapic timer early calibration result
x86/apic: Do not clear nr_irqs_gsi if no legacy irqs
x86/platform: Add a wallclock_init func to x86_platforms ops
x86/mce: Make mce_chrdev_ops 'static const'
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen-gntalloc: signedness bug in add_grefs()
xen-gntalloc: integer overflow in gntalloc_ioctl_alloc()
xen-gntdev: integer overflow in gntdev_alloc_map()
xen:pvhvm: enable PVHVM VCPU placement when using more than 32 CPUs.
xen/balloon: Avoid OOM when requesting highmem
xen: Remove hanging references to CONFIG_XEN_PLATFORM_PCI
xen: map foreign pages for shared rings by updating the PTEs directly
* 'unicore32' of git://github.com/gxt/linux:
unicore32, exec: remove redundant set_fs(USER_DS)
unicore32: Fix typo 'PUV3_I2C'
unicore32: drop unused Kconfig symbols
rtc: rtc-puv3: Add __devinit and __devexit markers for probe and remove
arch/unicore32: do not use EXTRA_AFLAGS or EXTRA_CFLAGS
unicore32: fix build error for find bitops
Some of the sun4v code patching occurs in inline functions visible
to, and usable by, modules.
Therefore we have to patch them up during module load.
Signed-off-by: David S. Miller <davem@davemloft.net>
To handle the large physical addresses, just make a simple wrapper
around remap_pfn_range() like MIPS does.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build regression introduced by commit 056879d2f2
(ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving
the intialization of the A3SP domain to a separate function and
providing an empty definition of it for CONFIG_PM unset.
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
These two syscalls were introduced during the last merge window.
Add the entries into the ARM call tables for them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit a15bd354f0.
It exceeded the padding on the SREGS struct, rendering the ABI
backwards-incompatible.
Conflicts:
arch/powerpc/kvm/powerpc.c
include/linux/kvm.h
Signed-off-by: Avi Kivity <avi@redhat.com>
Support guest/host-only profiling by switch perf msrs on
a guest entry if needed.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some cpus have special support for switching PERF_GLOBAL_CTRL msr.
Add logic to detect if such support exists and works properly and extend
msr switching code to use it if available. Also extend number of generic
msr switching entries to 8.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM on s390 always had a sync mmu. Any mapping change in userspace
mapping was always reflected immediately in the guest mapping.
- In older code the guest mapping was just an offset
- In newer code the last level page table is shared
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is a potential host deadlock in the tprot intercept handling.
We must not hold the mmap semaphore while resolving the guest
address. If userspace is remapping, then the memory detection in
the guest is broken anyway so we can safely separate the
address translation from walking the vmas.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
SIGP sense running may cause an intercept on higher level
virtualization, so handle it by checking the CPUSTAT_RUNNING flag.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPUSTAT_RUNNING was implemented signifying that a vcpu is not stopped.
This is not, however, what the architecture says: RUNNING should be
set when the host is acting on the behalf of the guest operating
system.
CPUSTAT_RUNNING has been changed to be set in kvm_arch_vcpu_load()
and to be unset in kvm_arch_vcpu_put().
For signifying stopped state of a vcpu, a host-controlled bit has
been used and is set/unset basically on the reverse as the old
CPUSTAT_RUNNING bit (including pushing it down into stop handling
proper in handle_stop()).
Cc: stable@kernel.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t
before copying it to userspace. There is a typo in the case that
we have 4 words to copy, meaning that we corrupt the compat_sigset_t.
It appears that _NSIG_WORDS can't be greater than 2 at the moment
so this code is probably always optimised away anyway.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Documentation/memory-barriers.txt document requires that atomic
operations that return a value act as a memory barrier both before
and after the actual atomic operation.
Our current implementation doesn't guarantee this. More specifically,
while a load following the isync can not be issued before stwcx. has
completed, that completion doesn't architecturally means that the
result of stwcx. is visible to other processors (or any previous stores
for that matter) (typically, the other processors L1 caches can still
hold the old value).
This has caused an actual crash in RCU torture testing on Power 7
This fixes it by changing those atomic ops to use new macros instead
of RELEASE/ACQUIRE barriers, called ATOMIC_ENTRY and ATMOIC_EXIT barriers,
which are then defined respectively to lwsync and sync.
I haven't had a chance to measure the performance impact (or rather
what I measured with kernel compiles is in the noise, I yet have to
find a more precise benchmark)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Recent binutils refuses to assemble AltiVec opcodes when in e500/SPE
mode, as some of those opcodes alias the "SPE" instructions. This
triggers an ancient binutils version check even when building a kernel
with CONFIG_ALTIVEC disabled.
In theory, the check could be conditionalized on CONFIG_ALTIVEC, but in
practice it has long outlived its utility. It is virtually impossible
to find binutils older than 2.12.1 (released 2002) in the wild anymore.
Even ancient RedHat Enterprise Linux 4 has binutils-2.14.
To fix the kernel build when done natively on e500 systems with this new
binutils, the test is simply removed.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is
broken on Book-E 64-bit parts that support delayed debug events. When
switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as
MSR_DE is also set and we aren't able to handle debug events from kernel
space.
We can remove the hack that always enables MSR_DE and loads up DBCR0 and
just utilize switch_booke_debug_regs() to get user space debug working
again.
We still need to handle critical/debug exception stacks & proper
save/restore of state for those exception levles to support debug events
from kernel space like we have on 32-bit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS
there is no need to have another such ifdef inside the function.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had an existing ifdef for 4xx & BOOKE processors that got changed to
CONFIG_PPC_ADV_DEBUG_REGS. The define has nothing to do with
CONFIG_PPC_ADV_DEBUG_REGS. The define really should be:
#if defined(CONFIG_4xx) || defined(CONFIG_BOOKE)
and not
#ifdef CONFIG_PPC_ADV_DEBUG_REGS
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PVHVM running with more than 32 vcpus and pv_irq/pv_time enabled
need VCPU placement to work, or else it will softlockup.
CC: stable@kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When mapping a foreign page with xenbus_map_ring_valloc() with the
GNTTABOP_map_grant_ref hypercall, set the GNTMAP_contains_pte flag and
pass a pointer to the PTE (in init_mm).
After the page is mapped, the usual fault mechanism can be used to
update additional MMs. This allows the vmalloc_sync_all() to be
removed from alloc_vm_area().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
[v1: Squashed fix by Michal for no-mmu case]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] topology: fix topology on z10 machines
[S390] crypto: avoid MSA3 and MSA4 instructions in ESA mode
[S390] avoid STCKF if running in ESA mode
[S390] zfcpdump: Do not initialize zfcpdump in kdump mode
[S390] ap: Setup processing for messages in request queue.
[S390] Kconfig: Select CONFIG_KEXEC for CONFIG_CRASH_DUMP
[S390] incorrect note program header
[S390] pfault: ignore leftover completion interrupts
[S390] fix pgste update logic
[S390] wire up process_vm syscalls
Move the PS3 IPI message setup from ps3_smp_setup_cpu() to ps3_smp_probe().
Fixes startup warnings like these:
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2649
Modules linked in:
...
---[ end trace 31fd0ba7d8756001 ]---
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes the PS3 bootup hang introduced in 3.0-rc1 by:
commit 317f394160
sched: Move the second half of ttwu() to the remote cpu
Move the PS3's LV1 EOI call lv1_end_of_interrupt_ext() from ps3_chip_eoi()
to ps3_get_irq() for IPI messages.
If lv1_send_event_locally() is called between a previous call to
lv1_send_event_locally() and the coresponding call to
lv1_end_of_interrupt_ext() the second event will not be delivered to the
target cpu.
The PS3's SMP IPIs are implemented using lv1_send_event_locally(), so if two
IPI messages of the same type are sent to the same target in a relatively
short period of time the second IPI event can become lost when
lv1_end_of_interrupt_ext() is called from ps3_chip_eoi().
CC: stable@kernel.org
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If you build with KVM and UP it fails with the following due to a
missing include.
/arch/powerpc/kvm/book3s_hv.c: In function 'do_h_register_vpa':
arch/powerpc/kvm/book3s_hv.c:156:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:156:10: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/kvm/book3s_hv.c:192:12: error: 'H_RESOURCE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:222:9: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c: In function 'kvmppc_pseries_do_hcall':
arch/powerpc/kvm/book3s_hv.c:228:30: error: 'H_SUCCESS' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:232:7: error: 'H_CEDE' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:234:7: error: 'H_PROD' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:238:10: error: 'H_PARAMETER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:250:7: error: 'H_CONFER' undeclared (first use in this function)
arch/powerpc/kvm/book3s_hv.c:252:7: error: 'H_REGISTER_VPA' undeclared (first use in this function)
make[2]: *** [arch/powerpc/kvm/book3s_hv.o] Error 1
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org (3.1 only)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
kdump fails because we try to execute an HV only instruction. Feature
fixups are being applied after we copy the exception vectors down to 0
so they miss out on any updates.
We have always had this issue but it only became critical in v3.0
when we added CFAR support (breaks POWER5) and v3.1 when we added
POWERNV (breaks everyone).
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org> [v3.0+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I had to debug a strange situation where all manner of things were
failing. SMT threads, storage and network were all completely broken.
The root cause was we couldn't find enough memory to instantiate RTAS -
this was a network install so the initrd was huge.
Instead of limping along and failing in mysterious ways we should just
panic up front if RTAS exists and we can't allocate space for it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kexec is not supported on 47x. 47x is a variant of 44x with slightly
different MMU and SMP support. There was a typo in the config dependency
for kexec. This patch fixes the same.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Should do what other architectures do and wrap all that code into
the appropriate ifdef
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: lantiq: use export.h in favour of module.h
MAINTAINERS: The MIPS git tree has moved.
MIPS: Fix build error due to missing inclusion of <linux/export.h>.
MIPS: ASID conflict after CPU hotplug
MIPS: Octeon: Fix compile error in arch/mips/cavium-octeon/flash_setup.c
MIPS: errloongson2_clock: Fix build error by including linux/module.h
STAGING: octeon-ethernet: Fix compile error caused by skb_frag_struct change
MIPS: Hook up process_vm_readv and process_vm_writev system calls.
MIPS: Kernel hangs occasionally during boot.
MIPS: Octeon: Mark SMP-IPI interrupt as IRQF_NO_THREAD
MIPS: BCM47xx: fix build with GENERIC_GPIO configuration
MIPS: NXP: Remove unused source files.
MIPS: Yosemite, Emma: Fix off-by-two in arcs_cmdline buffer size check
As per the comments added by this commit, %g2 turns out to not be a
usable place to save away orig_i0 for syscall restart handling.
In fact all of %g2, %g3, %g4, and %g5 are assumed to be saved across
a system call by various bits of code in glibc.
%g1 can't be used because that holds the syscall number, which would
need to be saved and restored for syscall restart handling too, and
that would only compound our problems :-)
This leaves us with %g6 and %g7 which are for "system use". %g7 is
used as the "thread register" by glibc, but %g6 is used as a compiler
and assembler temporary scratch register. And in no instance is %g6
used to hold a value across a system call.
Therefore %g6 is safe for storing away orig_i0, at least for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
