[Why]
For DGPU Navi, the wm_table.nv_entries are used. These entires are not
populated for DCN301 Vangogh APU, but instead wm_table.entries are.
[How]
Use DCN21 Renoir style wm calculations.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Ported logic from dcn21 for reading in pipe fusing to dcn30.
Supported configurations are 1 and 6 pipes. Invalid fusing
will revert to 1 pipe being enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After fixing nested FPU contexts caused by 41401ac677 we're still seeing
complaints about spurious kernel_fpu_end(). As it turns out this was
already fixed for dcn20 in commit f41ed88cbd ("drm/amdgpu/display:
use GFP_ATOMIC in dcn20_validate_bandwidth_internal") but never moved
forward to dcn21.
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 41401ac677 added FPU wrappers to dcn21_validate_bandwidth(),
which was correct. Unfortunately a nested function alredy contained
DC_FP_START()/DC_FP_END() calls, which results in nested FPU context
enter/exit and complaints by kernel_fpu_begin_mask().
This can be observed e.g. with 5.10.20, which backported 41401ac677
and now emits the following warning on boot:
WARNING: CPU: 6 PID: 858 at arch/x86/kernel/fpu/core.c:129 kernel_fpu_begin_mask+0xa5/0xc0
Call Trace:
dcn21_calculate_wm+0x47/0xa90 [amdgpu]
dcn21_validate_bandwidth_fp+0x15d/0x2b0 [amdgpu]
dcn21_validate_bandwidth+0x29/0x40 [amdgpu]
dc_validate_global_state+0x3c7/0x4c0 [amdgpu]
The warning is emitted due to the additional DC_FP_START/END calls in
patch_bounding_box(), which is inlined into dcn21_calculate_wm(),
its only caller. Removing the calls brings the code in line with
dcn20 and makes the warning disappear.
Fixes: 41401ac677 ("drm/amd/display: Add FPU wrappers to dcn21_validate_bandwidth()")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Currently if stream->signal is neither SIGNAL_TYPE_DISPLAY_PORT_MST or
SIGNAL_TYPE_DISPLAY_PORT then variable ret is uninitialized and this is
checked for > 0 at the end of the function. Ret should be initialized,
I believe setting it to zero is a correct default.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: bd0c064c16 ("drm/amd/display: Add return code instead of boolean for future use")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current atomic helpers have either their object state being passed as
an argument or the full atomic state.
The former is the pattern that was done at first, before switching to the
latter for new hooks or when it was needed.
Let's convert all the remaining helpers to provide a consistent
interface, starting with the planes atomic_check.
The conversion was done using the coccinelle script below plus some
manual changes for vmwgfx, built tested on all the drivers.
@@
identifier plane, plane_state;
symbol state;
@@
struct drm_plane_helper_funcs {
...
int (*atomic_check)(struct drm_plane *plane,
- struct drm_plane_state *plane_state);
+ struct drm_atomic_state *state);
...
}
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
struct drm_plane_helper_funcs *FUNCS;
identifier f;
identifier dev;
identifier plane, plane_state, state;
@@
f(struct drm_device *dev, struct drm_atomic_state *state)
{
<+...
- FUNCS->atomic_check(plane, plane_state)
+ FUNCS->atomic_check(plane, state)
...+>
}
@ ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
... when != new_plane_state
}
@ adds_new_state depends on plane_atomic_func && !ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
+ struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ depends on plane_atomic_func @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane,
- struct drm_plane_state *new_plane_state
+ struct drm_atomic_state *state
)
{ ... }
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-4-maxime@cerno.tech
[Why]
mutex_lock() was introduced in dm_disable_vblank(), which could
be called in an IRQ context. Waiting in IRQ would cause issues
like kernel lockup, etc.
[How]
Handle code that requires mutex lock on a different thread.
v2: squash in compilation fix without CONFIG_DRM_AMD_DC_DCN (Alex)
v3: squash in warning fix (Wei)
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
In some cases, this function is called when DIG BE is not
connected to DIG FE, in which case a value of zero isn't
invalid and assert should not be hit.
[How]
Remove assert and handle ENGINE_ID_UNKNOWN result in calling
function.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
dcn21_validate_bandwidth() calls functions that use floating point math.
On my machine this sometimes results in simd exceptions when there are
other FPU users such as KVM virtual machines running. The screen freezes
completely in this case.
Wrapping the function with DC_FP_START()/DC_FP_END() seems to solve the
problem. This mirrors the approach used for dcn20_validate_bandwidth.
Tested on a AMD Ryzen 7 PRO 4750U (Renoir).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206987
Signed-off-by: Jan Kokemüller <jan.kokemueller@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fix potential integer overflow by casting actual_calculated_clock_100hz
to u64, in order to give the compiler complete information about the
proper arithmetic to use.
Notice that such variable is used in a context that expects
an expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
actual_calculated_clock_100hz * post_divider
Fixes: 7a03fdf628 ("drm/amd/display: fix 64bit division issue on 32bit OS")
Addresses-Coverity-ID: 1501691 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Fix error handling in dc/dcn10/dcn10_hw_sequencer_debug.c
- DIO Supported for virtual displays
- memset dmub_rb_cmd to 0 which fixes issues talking with firmware
- fix 64bit division issue on 32bit OS
- move edp sink present detection to hw init to fix hang
- reverts a patch that caused 3x4K60 displays over MST
with DSC enabled to not light up
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is possible for ret_vsnprintf to be assigned negative value in
error cases. As an unsigned variable, negative values which
are stored in their 2's complement form gets treated as a positive
number. This will led to treating bad cases as good ones.
eg: -1 gets stored as 0xFFFFFFFF on a 32 bit system
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual displays do not use the backend of the pipe, and so have
infinite backend bandwidth.
[HOW]
Add a skip_dio_check bool to the VBA struct, which is used to override
the DIOSupport calculations.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Chris Park <Chris.Park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Since dmub_rb_cmds are not initialized to 0,
the header is filled with invalid data.
This is causing issues on the fw side.
[How]
Initialize dmub_rb_cmd unions to 0.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current implementation of mod_hdcp_hdcp2_validate_ake_cert()
does not process HDCP status message
TA_HDCP2_MSG_AUTHENTICATION_STATUS__SIGNATURE_CERTIFICAT_ERROR.
As a result, when there is a signature certificate error,
mod_hdcp_hdcp2_validate_ake_cert would return the default status,
which is success.
[How]
For all messages other than TA_HDCP2_MSG_AUTHENTICATION_STATUS__SUCCESS
and TA_HDCP2_MSG_AUTHENTICATION_STATUS__RECEIVERID_REVOKED, return status
as failure.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
VBIOS program DIG_CLK_PATTERN using engine ID instead of PHY ID.
Workaround by writing value for 0x1f (for HDMI) after calling vbios.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
On DCN1.0, need otg vertical line interrupt to get appropriate timing
to achieve specific feature request.
Add otg vertical interrupt0 support for registers which operation is
vertical sensitive.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dm struct is only being used if DCN config is defined and this
causes a unused variable warning if DCN option is not set.
[How]
Remove the compile flag so the variable is used (there also seems to be
a duplicate guard due to a bad rebase) so remove the outer guard to fix
the warning.
Fixes this warning
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c: In function 'dm_set_vblank':
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.c:5380:33: warning: unused variable 'dm' [-Wunused-variable]
Fixes: 98ab5f3513 ("drm/amd/display: Fix deadlock during gpu reset v3")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4c3a329273.
Bhawan's fix is better (less ifdefs), so revert this and apply Bhawan's.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Better handling of dummy p-state table
- Workaround for some legacy DP-VGA dongles
- Add Freesync HDMI support to DMCU
- Enable "trigger_hotplug" debugfs on all outputs
- fix initial bounding box values for dcn3.02
- implement support for DID2.0 dsc passthrough
- fix calculation for the pwl backlight curve
- Fix multiple memory leaks
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Overlay won't move to a new positon if viewport size is smaller than
what can be handled. It'd either disappear or stay at the old
position. This condition is for example hit if overlay is moved too
much outside of left or top edge of the screen, but it applies to
any non-cursor plane type.
[how]
Reject this contidion at validation time. This gives the calling
level a chance to handle this gracefully and avoid inconsistent
behaivor.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some scenarios where we use a UCLK frequency in between dummy p-state table
entries result in a p-state hang, due to the table not having a close
enough match, so the default DPM0 latency is used, which can be too long to
support dummy p-state switching in these scenarios.
[How]
- old: match if current freq is within +- margin of table entry
- new: find largest table entry that is lower than current freq + margin
- lower than DPM0 will still use DPM0
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Maximum resolution is 1440*900 when connecting to FHD monitor via some DP-VGA
dongles. The display EDID reading fails over AUX/I2C via DP->VGA dongle, and
this leads to the maximum resolution 1920*1080 cannot be obtained from EDID.
[How]
Provide a workaround for some legacy DP-VGA dongles with a longer aux delay.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
An old dc_sink state is causing a memory leak because it is missing a
dc_sink_release before a new dc_sink is assigned back to
aconnector->dc_sink.
[how]
Decrement the dc_sink refcount before reassigning it to a new dc_sink.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
drm_atomic_commit was changed so that the caller must free their
drm_atomic_state reference on successes.
[how]
Add drm_atomic_commit_put after drm_atomic_commit call in
dm_force_atomic_commit.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
