regmap should handle any byte ordering issues required, it is looking for
a byte stream from the bus, so don't set 16 bits per word. This is likely
to have tested out OK due to use of an unmerged SPI controller driver.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Freeing the current list element while iterating over the list will cause a use
after free since the iterator function will still use the current element to
look up the next. Use list_for_each_safe() and remove the element from the list
before freeing it to avoid this.
Fixes: 1438c2f60b ("ASoC: Add a per component dai list")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Kconfig symbol X86_32 was introduced in October 2005, it's about time
to use it :-)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CS5536 companion chipset is not only used on 32-bit x86 systems as
I originally thought, it is also used on MIPS Loongson/Lemote 2
systems. So let the snd-cs5535audio driver be built on MIPS too.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the CODEC driver could specify its own I/O(read and write)
while registering the CODEC for some reason, maybe the MFDs is
used, etc.
So just do check it, if they are not specified by CODEC driver
then try to set up the default regmap I/O if regmap is used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Since the only control type that left is SND_SOC_REGMAP, so remove it. Drop
the control params and add struct regmap *regmap to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch initialized the local audio InfoFrame variable 'ai' to be all zero,
thus the data bytes will indicate "Refer to Stream Header" by default.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CS5530, CS5535 and CS5536 chipsets are companions of the Geode
series of processors, which are 32-bit x86 processors. So the
snd-cs5530 and snd-cs5535audio drivers are only needed on this
architecture, except for build testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few things here:
- Avoid memory leaks in error cases with DPCM, this code has never been
that well tested in mainline due to the lack of mainline drivers but
we now have one queued for the merge window!
- Fix the N810 audio driver to load when booted with DT since the
platform was converted to DT during the merge window.
- Fixes for initialisation of some MFD drivers that are probably unused
in mainline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTHgKsAAoJELSic+t+oim9JJkQAJOQz8x2BzpaQQfsnXuwNXwv
ShBeqGNcv66KtqcKDFHumL4k2fkewuwdsm3Nc/orUD3JI3mywdKStQH2/N9TAC6v
KzSufl4Xs6ByyeayxZSZTf7wEbSvqxT75dnmzso6YPRV7sPK/cdRtFoRFXTtJqB7
ixIRzfnatFvBhZVCgeGkS8WXzAFteXJF6Y90m+qNBJfgwO09gW4Gj2C6CW2kYfBm
3m+JGjGN8pAsvS3JVPAIDdyswxK0BUzDbRjsfXr+SvdbXaemmYhnRWeW4FLrv6Q3
DakMb/OlUJF3kq+9G6q1wMsieeIfErXwHs6SSurSHwg3+KJljYnZka9Vlh8dU/44
CrxMG/FS6RjZRLMq8090/ho59uQ2Qh79Qn2PTM5nZ5TmMDMTxw1xXl95BuGsZ3wd
5lPoP35LBFuOzxLuQs2Uz0p65uN3VETMgSW7FAOEpdh4SxHBG9veWjkrbvXvdtEd
9pUH3k4O9nX7KOJsGWreBprTRZQuw9REiZ36tVb1Qe2TSPmkbTzHGhNcezdlLifm
UWMIG4bR1lnKWMpQTd35ErzniJSyi8fJ55gbEm4ovq1FWHuueURPRD5OFAbHLLyR
FRxq9UFKGenzcsDksqU2gef7LKhauAcoLPiXXswL1qaZz/sTgmoqV63pZuxBiA+p
Avd3Dy1u5xZ4IM0B+Kr0
=2H5y
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.14
A few things here:
- Avoid memory leaks in error cases with DPCM, this code has never been
that well tested in mainline due to the lack of mainline drivers but
we now have one queued for the merge window!
- Fix the N810 audio driver to load when booted with DT since the
platform was converted to DT during the merge window.
- Fixes for initialisation of some MFD drivers that are probably unused
in mainline
For controls registers with snd_soc_add_dai_controls snd_kcontrol_chip() returns
a pointer to the DAI, not to the CODEC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to spot locking issues by asserting that the DAPM mutex is held when
it should be. There's a bit of fun due to us not requiring the lock to be
held prior to the card being instantiated which mean we need to wrap the
assert in some paths and this isn't methodical by any stretch of the
imagination.
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that every DAI has a component we can track the DAIs on a per component
basis. This simplifies the DAI lookup when we are only interested in DAIs of a
specific component and also makes it possible to have multiple components with
the same parent device and also register DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_register_dais() looks up the CODEC that is registering the DAIs by
looping over all registered CODECs. This patch updates the code to
simply pass the CODEC that registers the DAIs to snd_soc_register_dais() thus
avoiding the lookup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_register_dais() has basically the same code as snd_soc_register_dai(),
but running in a loop. The only difference is that snd_soc_register_dai() calls
fmt_single_name() to generate the DAIs name and snd_soc_register_dais() calls
fmt_multiple_name(). This patch pushes the check in __snd_soc_register_component()
which decides whether to call snd_soc_register_dai() or snd_soc_register_dais()
to snd_soc_register_dais() to decide which naming scheme to use. This allows us
to remove snd_soc_register_dai().
The patch also updates snd_soc_register_dais() to unregister every DAI it finds
for the component rather than trying to unregister one DAI for each DAI that was
registered. Both have the same result since there won't be more DAIs than what
have been registered, but the former is easier to implement.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 88pm860 is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced in commit
f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Fixes: f9ded3b2e7 ("ASoC: 88pm860x: Use regmap for I/O").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The si476x is a MFD device and the CODEC driver is using the regmap struct of
the parent device, hence automatic IO setup will not work and we need to
manually call snd_soc_codec_set_cache_io(). The issue was introduced commit
d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Fixes: d6173df35f ("ASoC: si476x: Remove custom register I/O implementation")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
While we are at it also remove the snd_soc_dapm_enable_pin() in the init
callback. Pins are enabled by default.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_card.name is now option on DT case.
non-DT case can follow same style,
and it is understandable from platform point of view.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tlv320aic32x4 related lines were wrongly placed after tlv320aic3x lines.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is quite confusing to name the pointer to davinci_pcm_dma_params as
dma_data. Rename the pointer to avoid confusion.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The reference clock path on newer IP FLLs requires a different
configuration, and should avoid integer mode operation. This patch adds
support for both the new encoding and updates the calculation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No part of the FLL calculation depends on the value determined for the
gain but the gain does depend on other values. In preparation for future
updates this patch moves the gain to be the last thing calculated.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
OUTDIV will remain unchanged whilst the rest of the FLL configuration is
calculated so do this first.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As we now calculate the FLL configuration at a later stage in the
process the fout member of the FLL structure will contain the desired
Fout frequency so no need to pass this in seperately.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the FLL configuration is calculated before it is known which
FLL path the configuration will be applied to. Newer versions of the IP
have differences in the configuration required for each FLL path, which
makes it complicated to calculate the FLL configuration in advance.
This patch simply checks the validity of a requested input and output
frequency before we know which FLL path they will be applied to and
saves the actual calculation of the configuration until we know where
the settings will be applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we know in arizona_apply_fll if we are setting the sync or ref
path there is no need to set the outdiv seperately anymore. This patch
moves this from arizona_enable_fll to arizona_apply_fll.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Improve readability by adding defines for some of the constants
associated with FLL configuration.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
One is not a valid value for the OUTDIV start searching at 2 instead.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following build errors when aic23 is configured as
module:
>> ERROR: "tlv320aic23_probe"
>> [sound/soc/codecs/snd-soc-tlv320aic23-i2c.ko] undefined!
>> ERROR: "tlv320aic23_regmap"
>> [sound/soc/codecs/snd-soc-tlv320aic23-i2c.ko] undefined!
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move to the new style of defining the bus interfaces in separate modules
in order to simplify dependencies.
Signed-off-by: Mark Brown <broonie@linaro.org>
Lenovo IdeaPad 410Y with ALC282 codec makes loud click noises at boot
and shutdown. Also, it wrongly misdetects the acpi_thinkpad hook.
This patch adds a device-specific fixup for disabling the shutup
callback that is the cause of the click noise and also avoiding the
thinpad_helper calls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71511
Reported-and-tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
tlv320aic23 chip control interface may work in either I2C or SPI mode
depending on the MODE pin state. Functionality and register layout are
independent of the control mode.
Implement bus-specific parts as separate modules.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the Haswell driver to use .dai_fmt in DAI link to set the
format.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In snd_soc_bytes_put function, it forces cpu to do cpu_to_be translation,
but for mmio bus which uses REGMAP_ENDIAN_NATIVE, it doesn't need to do
endian translation. So it is better to use regmap's api which can decide
if this translation is needed according to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is useful for generic code built on top of regmap dealing with
blocks of data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uRux
-----END PGP SIGNATURE-----
Merge tag 'parse-val' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-core
regmap: Add parse_val() API
This is useful for generic code built on top of regmap dealing with
blocks of data.
This connects platform DAI, SiRF internal audio codec DAI and
SiRF auido port DAI together and works as a mach driver.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is used by SIRF internal audio codec.
Use dedicated SiRF audio port TXFIFO and RXFIFO
Supports two DMA channels for SiRF audio port TXFIFO and RXFIFO
The audio port like as audio bus such as i2s.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for componentization move the ignore_pmdown_time field from the
snd_soc_codec struct to the snd_soc_component struct. Set it to true for non
CODEC components for now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no reason why active count tracking should only be done for CODECs but
not for other components. Moving the active count from the snd_soc_codec struct
to the snd_soc_component struct reduces the differences between CODECs and other
components and will eventually allow component to component DAI links (Which is
a prerequisite for converting CODECs to components).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Keep track of which component registered a DAI. We'll need this as
componentization progresses.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of directly checking the 'active' field of the CODEC struct add a new
helper function that will return either true or false depending on whether the
CODEC is active. This will make the migration to the component level easier.
The patch also updates all CODEC drivers that check the active attribute to use
the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC links we need to make sure to also manage the 'active' field
of the cpu_dai CODEC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code that increments and decrements the active field of the
various PCM runtime components (all with the same bugs). Factor this out into
common helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC links we should only immediately power down if both CODECs
are configured to ignore the power down delay. Factor the logic for this
into a helper function that can be used for both compressed and normal PCMs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
The firmware files can be quite large and allocating the whole firmware
a single DMA safe buffer can be problematic if the system is under a
high memory load. Ease the requirements slightly by writing the firmware
out in page sized chunks.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
cs4271_common_probe() is called from cs4271_i2c_probe() but defined in
CONFIG_SPI_MASTER block, thus it results in a build error when
CONFIG_SPI_MASTER=n:
sound/soc/codecs/cs4271.c:721:2: error: implicit declaration of function ‘cs4271_common_probe’ [-Werror=implicit-function-declaration]
Move the function out of #if block.
Fixes: d6cf89ee07 ('ASoC: cs4271: claim reset GPIO in bus probe function')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Calling "kfree(byt)" is a double free because that was allocated with
devm_kzalloc(). There were a couple places which leak "byt->msg". That
memory is allocated in msg_empty_list_init().
Fixes: f7d01fd675 ('ASoC: Intel: Add Intel Baytrail SST DSP IPC support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Logitech C500 (046d:0807) needs the same workaround like other
Logitech Webcams.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous dev_err() conversion resulted in a code that may give
NULL dereference in snd_emu10k1_ptr_write(). Since it's a sanity
check, better to be replaced with a debug macro like other places in
this driver.
Fixes: 6f002b0216 ('ALSA: emu10k1: Use standard printk helpers')
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are some places where we dereference "chip" in the error message
but we've already freed it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"chip" is NULL here. We don't need a printk here because kmalloc() has
it built in.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the driver behavior compatible with the earlier kernels,
use the analog beep in the loopback path instead of the digital beep.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer widget (NID 0x20) of AD1884 and AD1984 codecs isn't
connected directly to the actual I/O paths but only via another mixer
widget (NID 0x21). We need a similar fix as we did for AD1882.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
30d0341e7d
(ASoC: simple-card: simplify the daifmt code)
simplify cpu/codec dai_fmt which consists from
dai specific format + common format.
But, it didn't care about non-DT case.
This patch fixes it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound has SCU unit which has SRC/CTU/MIX/DVC,
and current rsnd driver has scu.c and scu module.
Current scu.c has SRC support only.
My first concept was control these feature on scu.c
but, it become difficult and un-understandable now.
This patch rename scu to src
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now, rsnd_xxx_remove() do nothing.
remove these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd_dai_remove() called rsnd_path_exit(),
but these memory will be cleaned automatically.
Because it is created by devm_kzalloc().
nothing to do on rsnd_dai_remove()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Each rsnd mod needs specific probe method,
and its best timing is DAI probe timing.
But current code runs it mod probe timing.
This patch adds new probe/remove callback to solve it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was added.
Thus, rsnd_scu_ssi_mode_init() is called from SSI
directory by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was used.
Thus, SSIU irq setting is called from SSI
directory by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is assuming that SCU/SRU ID is
same as SSIU/SSI ID, because Gen1 can't select it.
But, Gen2 can select it.
The SCU/SRU/SSIU/SSI pair depends on the platform.
This patch get correct SCU ID from platform info.
To keep compatible, it still assuming SCU ID = SSI ID
if platform doesn't have info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound DAI consists from SSI/SCU/SSIU/SRU...
Current R-Car sound DAI is decided from these settings,
but it is intuitively unclear, and is not good design for DT support.
This patch adds new rsnd_dai_platform_info to solve this issue.
But now, many platform is using this driver without
rsnd_dai_platform_info.
So, this patch still supports DAI settings via SSI to keep compatible.
It will be removed in next Linux version.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dpcm_path_get() allocates dynamic memory to hold path list.
Corresponding dpcm_path_put() must be called to free the memory.
dpcm_path_put() is not called under several error conditions.
This leads to memory leak.
Signed-off-by: Patrick Lai <plai@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The driver uses automatic IO setup, which will also initialize the control_data
field of the CODEC, no need to do it manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no point in using FIQ if DMA is available (it is selected) and
selecting FIQ currently breaks the build on non-i.MX platforms. If FIQ
is actually required the build will need to be restricted or have a
select for the relevant FIQ code adding.
Signed-off-by: Mark Brown <broonie@linaro.org>
Pre-merge code was using direct hw_read() calls as an out of framework
way of doing volatile register I/O when not using regmap. This has never
functioned correctly in mainline due to the regmap conversion, the
hw_read() implementation still does caching. In order to facilitate
removal of the subsystem level I/O code convert to use snd_soc_read(),
there should be no functional impact.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
When plugging a headphone or headset, lots of noise is heard from
internal speaker, after changing the automute via amp instead of
pinctl, the noise disappears.
BugLink: https://bugs.launchpad.net/bugs/1268468
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the snd_soc_cache_init(), the reg_size maybe zero and then the value
of codec->reg_cache, which is alloced via kzalloc, maybe equal to
ZERO_SIZE_PTR. If the reg parameter of snd_soc_cache_write() is large enough,
the cache[idx] = val maybe cause the kernel crash...
So this patch fix this via doing the zero pionter check of it.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since 3.14-rc1 only DT boot has been supported on N810, so this
file fails to init. Make a minimal fix to retain functionality.
This file should be properly converted to DT in longer term.
There seems to be still other unresolved issues with N810 audio support,
but this patch is needed at minimum as otherwise the machine driver
probing would completely fail.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Gen1/Gen2 code never be used in same time.
Thus, driver can share Gen1 only register and Gen2 only register.
It can reduce memory too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd_adg_ssi_ws_timing_gen2() returns SSI WS timing,
and it used "mod" as parameter.
but, this "mod" is sometimes not ssi mod.
Get SSI mod from rsnd_dai_stream
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound consists of many devices.
It will have more device support in the future.
Thus, for each probe become now function pointer array.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current driver is assuming that SSI id = SCU id.
But, now, it can get correct SSI/SCU from
rsnd_dai_stream. use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct rsnd_dai_stream used list for mod list.
It added only odd flexibility to current driver, and
it is a factor which makes extendibility difficult.
rsnd use mod array instead of list from now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd SSIU/SSI/SCU/SRU path is set
when playback/capture starts up.
But it is meaningless method, since the path is based
on platform and can be set in probe() timing.
This patch sets the path on probe() timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the ongoing component-ization of the ASoC framework and the continuing
migration to using regmap for IO the control_data field of the snd_soc_codec
struct will eventually be removed. Prepare the wm5192, wm5110 and wm8997
drivers for this by using arizona->regmap instead of accessing the CODEC's
control_data field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8763 driver uses regmap for IO which means that codec->cache_sync is not
used. The line was added in commit d3398ff ('ASoC: Convert WM8753 to direct
regmap API usage'). Presumably this was meant to be regcache_mark_dirty(), but
since we already call regcache_mark_dirty() in the core when suspending the
CODEC it is safe to just remove the line.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sound/soc/soc-core.c:2708:6-13: WARNING: Assignment of
bool to 0/1
sound/soc/soc-core.c:2726:3-10: WARNING: Assignment of
bool to 0/1
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sound/soc/soc-core.c:2708:6-13: WARNING: Assignment of
bool to 0/1
sound/soc/soc-core.c:2726:3-10: WARNING: Assignment of
bool to 0/1
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ops to read and write registers should take pointers labeled as
__iomem. Thanks to the sparse bot for catching this.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using readl, writel, etc. resulted in some architectures, such as
s390, expanding the member names into zpci_writel. Obviously not the
intended result.
Fixes s390 build breakage introduced by "4083081 - ALSA: hda - Allow
different ops to read/write registers"
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new sequence ensure that dapm_pre_sequence_async work on
the card before all codecs and dapm_post_sequence_async work
on the card after all codecs.
So the machine driver could utilize the determinate sequence
to do the gloabl setup and teardown in the right place.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The widgets generated by the machine driver need to power off too.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit cleaner and on the other hand the board level DAPM elements
get registered in the card's DAPM context rather than in the CODEC's DAPM
context.
Also drop the two snd_soc_dapm_enable_pin() since pins are enabled by default
and there is no matching snd_soc_dapm_disable_pin() in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit cleaner and on the other hand the board level DAPM elements
get registered in the card's DAPM context rather than in the CODEC's DAPM
context.
Also remove the snd_soc_dapm_enable_pin() calls, since pins are enabled by
default and there are no matching snd_soc_dapm_disable_pin() calls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit cleaner and on the other hand the board level DAPM elements
get registered in the card's DAPM context rather than in the CODEC's DAPM
context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit cleaner and on the other hand the board level DAPM elements
get registered in the card's DAPM context rather than in the CODEC's DAPM
context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit cleaner and on the other hand the board level DAPM elements
get registered in the card's DAPM context rather than in the CODEC's DAPM
context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When calling {corgi,poodle,spitz}_ext_control() from the startup callback we
pass the CODEC's DAPM context instead of the card's DAPM context. This is not a
problem per se since all the DAPM functions in ext_control() fallback to widgets
from other DAPM contexts, but passing the card's context is more consistent.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the controls and DAPM widgets and routes.
This on one hand makes the code a bit shorter and cleaner and on the other hand
the board level DAPM elements get registered in the card's DAPM context rather
than in the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
With GTA01 support gone from the driver there is no need to keep a separate
initilization routine for the GTA02 specific bits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct rsnd_dai is called as "rdai",
but its size has been called as "dai_nr".
Unify these as "rdai"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
scu/ssi probe() already have more detail debug message.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
priv has rcar_snd_info pointer.
having priv and info in same time is verbose.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
core.c is the only user of rsnd_mod_call() macro.
Move it to core.c from rsnd.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no big meaning, but preparation for platform dai support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove the dependency on CONFIG_PCI for building hda codec drivers so
that platforms with HDA attach via means other than PCI can use them.
This was as suggested by tiwai.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codec creation and stream initialization can be shared between
hda_intel and hda platform drivers. Move it and the static functions
it depends on to hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code will be reused by an hda_platform driver as it has no PCI
dependencies. This allows update_rirb to be static as all users are
now in hda_controller.c.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This op will be used by hda_intel to do the position check. Takashi
wisely suggested adding this before moving the interrupt handler to
common HDA code. Having this callback prevents the need to move the
hda_intel specific delayed interrupt handling with the irq.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Share more code from hda_intel. This moves the link control and
initialization to hda_controller. The code will also be used by an
hda platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Combining the call to alloc_cmd_io with the allocate pages function
removes an extra interface between hda_intel and hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is done to allow an HDA platform driver to reuse the code.
A few of the interfaces added to hda_controller will disappear in
following commits as their users are also moved to hda_controller.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Moving the DSP loading functionality to hda_controller.c means that
the dsp lock doesn't need to be shared in hda_intel and
hda_controller. The forthcoming platform driver doesn't need the DSP
loading code, but sharing it doesn't hurt.
Tested on Chromebook Pixel's ca0132 that uses the DSP loader.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull allocation from first_init to a new function in hda_controller.c.
Short term this will allow the dsp loader to be moved as well. In
later commits it will allow the same allocation to be used by the
platform hda driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull the pcm_ops and the functions they use into a new hda_controller
file. This is done to allow for other hda implementations besides PCI
to use the same ops. The hda_controller file will house functionality
related to HDA but independent of the bus used to talk to the
controller.
This currently shares dsp locking across the two files. This will be
remedied in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding this op allows the X86 specific mmap operation to help in
hda_intel without needing a CONFIG_X86 in future non-PCI hda drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Break out the allocation of pages for DMA and PCM buffers to ops in
the chip structure. This is done to allow for architecture specific
work-arounds to be added. Currently mark_pages_wc is used by
hda_intel. This avoids needing to move that x86-specific code to a
common area shared with hda platform drivers.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Passing the max slots and power save arguments to codec_create will
allow for its reuse by an hda_platform driver. It makes the function
independent of the module params in hda_intel and ready to move to
hda_shared in a following commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keeping a pointer to the jackpoll_ms array in the chip will allow
azx_codec_create to be shared between hda_intel and hda_platform
drivers. Also modify get_jackpoll_ms to make the jackpoll_ms member
optional, this way a platform driver can leave it out if it's not
needed.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although the code was updated last year the "#if 0" surrounding it
dates back to the original git commit. The function will be moved to
a new file, no need to carry the dead code.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a PCI-only feature, but adding a callback for it in the chip
structure breaks the PCI dependency in the RIRB code allowing the
logic there to be re-used by the platform HDA driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes calls to get the device via PCI from other parts of the
code that will be able to be re-used by the platform driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will allow for a platform hda driver to use it as well. It
removes the dependency on the module param from hda_intel, which will
allow for azx_setup_periods to be shared.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The forthcoming platform hda driver needs to override the way
registers are read and written. In preparation for that, introduce a
reg_ops struct that can be implemented differently by the new driver.
Change the existing macros to use the new structure, and move them to
hda_priv.h where they will be accessible to both PCI and platform
drivers.
Start with register access, but later commits will add more ops that
differ between PCI and platform.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Later commits adding support for hda platform drivers will want to use
the same defines and structures. Put them in a place reachable by both
hda_intel and the new platform driver.
This is a mostly a direct copy with a few whitespace and comment
changes to make checkpatch happy.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are three different completely independent code paths in
dapm_set_path_status(). One of them is never used at all and the other two (one
for mixers, one for MUXs) have their distincive callsites that always go onto
the same path. Breaking the function into two parts allows us to reduce the code
size and in the MUX case also do some optimizations to avoid having to calcualte
the selected item for each item again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
MUXs and virtual MUXs are almost identical, the only difference is that for
virtual MUX there is no hardware backing register in which setting is stored.
This patch adds code, which is similar to what we already do for DAPM mixer
controls to support virtual mixer controls, to DAPM enum controls. The new code
will check if the enum does a hardware backing register and skip over reading
and writing to the register if it has not. This allows us to use the same code
path for both MUXs and virtual MUXs and a lot of nearly identical code can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the upcoming consolidation for MUXs and virtual MUXs we need to mark virtual
enums as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
MUXs and value MUXs are almost identical, the only difference is that a value
MUX uses a look-up table to map from the selected control item to a register
value, while MUXs use a direct mapping. This patch uses
snd_soc_enum_item_to_val() and snd_soc_enum_val_to_item(), which where earlier
introduced during the consolidation of enum and value enum controls, to hide
this difference. This allows us to use the same code path for both MUXs and
value MUXs and a lot of nearly duplicated code can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementations for enum and value enum controls are almost identical. The
only difference is that the value enum uses an additional look-up table to map
the control value to the register value, while the enum control uses a direct
mapping. Enums and value enums can easily be distinguished at runtime, for value
enums the values field of the snd_soc_enum struct contains the look-up table,
while for enums it is NULL. This patch adds two new small helper functions
called snd_soc_enum_item_to_val() and snd_soc_enum_val_to_item() which map
between register value and control item. If the items field of the snd_soc_enum
struct is NULL the function will do a direct mapping otherwise they'll use the
look-up table to do the mapping. Using these small helper functions it is
possible to use the same kcontrol handlers for both enums and value enums. The
functions are added a inline functions in soc.h so they can also be used by the
DAPM code to accomplish similar consolidation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to the HDA spec, we must write 1 to bit 15 on a CORBRP
reset, read back 1, then write 0, then read back 0. This must be
done while the DMA is not running.
We accidentaly ended up writing back the 0 by using a writel
instead of a writew to CORBWP.
This caused occasional controller failure on Bay Trail hardware.
[replaced error messages with dev_err() by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep input device is registered via input_register_device(), but
this is called in snd_hda_attach_beep_device() where the sound devices
aren't registered yet. This leads to the binding to non-existing
object, thus results in failure. And, even if the binding worked
(against the PCI object), it's still racy; the input device appears
before the sound objects.
For fixing this, register the input device properly at dev_register
ops of the codec object it's bound with. Also, call
snd_hda_detach_beep_device() at dev_disconnection so that it's
detached at the right timing. As a bonus, since it's called in the
codec's ops, we can get rid of the further call from the other codec
drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Basically, soc_bind_dai_link() checks
cpu_dai->dev->of_node and dai_link->cpu_of_node in DT case.
But after that it will check
cpu_dai->name and dai_link->cpu_dai_name too.
On the other hand, snd_soc_dai :: name is created by
fmt_single_name() or fmt_multiple_name().
There is no confusion if dai name is created by fmt_multiple_name(),
since cpu_dai->name is same as dai_link->cpu_dai_name.
but, if dai name is created by fmt_single_name(), CPU DAI never match.
Thus, simple-card not set dai_link->cpu_dai_name if DT case
to skip naming match on soc_bind_dai_link()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most CODEC drivers which the REGMAP is used, the soc_probe_codec()
will do the stuff work of snd_soc_codec_set_cache_io(), which the CODEC
drivers' ASoC probe will do too, and almost at the same time.
This patch set the default I/O up try regmap, and then the CODEC drivers'
stuff work of snd_soc_codec_set_cache_io() will be redundant, while if one
CODEC driver needed to set it's own I/O, then it can rewrite the default ones.
Then could we just discard the snd_soc_codec_set_cache_io() from the CODEC
drivers' ASoC probe to simplify the code.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that all users have been converted to regmap and the config.reg_bits
and config.val_bits can be setted by each user through regmap core API.
So these two params are redundant here.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SGI Visual Workstation seems to be dead; remove support so we
don't have to continue maintaining it.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Michael Reed <mdr@sgi.com>
Link: http://lkml.kernel.org/r/530CFD6C.7040705@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Many HP laptops with STAC codecs have a docking station port and BIOS
sets the pins for the input on the dock as a line in. Because the
generic parser doesn't handle a line in pin as auto-switchable, this
resulted in the manual capture source selection on these laptops.
However, from the usability POV, the automatic switching is easier.
This patch adds the line_in_auto_switch hint in the fixup function for
these laptops. Even if no dock port is present, this should be
harmless as the generic parser allows the auto-switching only in a
limited situation (all three pins are located in different
positions).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few more driver specific bug fixes, all driver specific things that
only affect users of those devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GL3V
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.14-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.14
A few more driver specific bug fixes, all driver specific things that
only affect users of those devices.
Instead of the controller, the new codec object is assigned as a
parent for the hd-audio beep input devices, just like already done for
PCM and hwdep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a typo in the Limiter2 Release Rate control, a wrong enum for
Limiter1 is assigned. It must point to Limiter2.
Spotted by a compile warning:
In file included from sound/soc/codecs/sta32x.c:34:0:
sound/soc/codecs/sta32x.c:223:29: warning: ‘sta32x_limiter2_release_rate_enum’ defined but not used [-Wunused-variable]
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
include/sound/soc.h:275:18: note: in definition of macro ‘SOC_ENUM_DOUBLE_DECL’
struct soc_enum name = SOC_ENUM_DOUBLE(xreg, xshift_l, xshift_r, \
^
sound/soc/codecs/sta32x.c:223:8: note: in expansion of macro ‘SOC_ENUM_SINGLE_DECL’
static SOC_ENUM_SINGLE_DECL(sta32x_limiter2_release_rate_enum,
^
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
A somewhat large set of fixes here due to the identification of some
systematic problems with hard to use APIs in the subsystem. Takashi did
a lot of work to address the enumeration API which uncovered a number of
off by one bugs caused by confusing APIs while Charles addressed issues
in the locking around DAPM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ty2j
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.14
A somewhat large set of fixes here due to the identification of some
systematic problems with hard to use APIs in the subsystem. Takashi did
a lot of work to address the enumeration API which uncovered a number of
off by one bugs caused by confusing APIs while Charles addressed issues
in the locking around DAPM.
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert with dev_err() and co from snd_printk(), etc.
As there are too deep indirections (e.g. ep->chip->dev->dev),
a few new local macros, usb_audio_err() & co, are introduced.
Also, the device numbers in some messages are dropped, as they are
shown in the prefix automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
A couple of prints are difficult to convert with dev_err() so they are
converted to pr_err() at least.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
The debug prints are also reformatted to suit with dev_dbg().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
