Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.
Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.
Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.
No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 0b7fde54f9 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.
Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices. The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.
ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.
This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc_tx_get_slot can return zero as valid index.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use corresponding macros defined in include/linux/ieee80211.h
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit be663ab670 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.
Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.
By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.
Also, remove some unnecessary castings and use union member accesses
instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.
Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.
The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.
In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
multiple places.
3. In the current implementation, the block_size member can be
misleading because a zero value actually means that there's no need to
align. Declare a block size alignment quirk instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.
Update the commentary in order to consider the one valid scenario
where this can happen: roaming.
Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.
Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.
Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).
Fix it by rearranging the elp calls to come along with mutex_lock/unlock.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.
Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using an array of booleans to mark the channels we had already
scanned. This was causing a sparse error, because bool is not a type
with defined size. To fix this, use bitmasks instead, which is much
cleaner anyway.
Thanks Johannes Berg for the idea.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?
Both functions should be static.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310. It now means the passive scan compensation
percentage during A2DP EDR. Instead of 50, we need to use 200.
Fix the SG configuration accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT). Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.
This requires Eliad's fix to set the actual TID in the TX descriptor.
Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.
It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)
Fix it by using the actual tid stored in skb->priority.
Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.
The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.
Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow early termination of 50 consecutive beacons.
This value is the recommended one by the 12xx's system/RF team,
and tests show that power consumption is improved as expected.
Reported-by: Ruthy Zaphir <ruthyz@ti.com>
Tested-by: Danil Shalumov <danils@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx chip supports one Rx STBC spatial stream. Announce this in
the HT capabilities info field.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rx-status passed to mac80211 along with each received frame contains the
band on which the frame was received. Under certain circumstances, this band
information may be incorrect, causing in worst case a WARNING from mac80211,
and causes the received frame to be dropped.
This scenario mainly occurs when performing connected-mode scans, when the
received scan results are from the other band than the one currently
associated to.
[Since desc_band doesn't exist anymore, use status->band in the later
call to ieee80211_channel_to_frequency() to fix compilation -- Luca]
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All the new firmware versions (>=6.1.3.50.58 for STA and >=6.2.0.0.47
for AP) use 1 spare TX block. We still want to support older
firmwares that require 2 spare blocks, so added a quirk to handle the
difference.
Also implemented a generic way of setting quirks that depend on the
firmware revision.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to wl128x chip via chip id
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.
Only send dummy packet when not in AP mode.
[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code. Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for
dummy packets -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reduced bus transactions in the Tx & Rx path.
[Removed unnecessary check wl->chip.id != CHIP_ID_1283_PG20 when
checking the quirk -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.
This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.
Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.
[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.
[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Take care of FW & NVS with the auto-detection between wl127x and
wl128x.
[Moved some common code outside if statements and added notes about
NVS structure assumptions; Fixed a bug when checking the nvs size: if
the size was incorrect, the local nvs variable was set to NULL, it
should be wl->nvs instead. -- Luca]
[Merged with potential buffer overflow fix -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New general and radio parameters structures and functions.
Implemented as separate functions due to auto-detection
between wl127x and wl128x.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c
Signed-off-by: Luciano Coelho <coelho@ti.com>
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.
Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).
[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to prevent overran of IRQ polarity via FW the polarity setting move after
FW download and before IRQ enable.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When testing some new P2P code, Angie found that the
driver might crash because the beacon command ended
up being bigger than a regular command. This is quite
obvious -- a normal command is limited to roughly 360
bytes but a beacon may be much larger of course.
To fix this, use the huge command buffer.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since huge commands all share a single buffer,
there can only be a single one in flight at a
time since otherwise they'd overwrite each
other. This is true in the driver now, but it
seems like a possible source of bugs, so add
a test to verify that huge commands are always
sent synchronously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a number of things in the driver that
may result in a BUG(), which is suboptimal since
it's hard to get debugging information out of
the driver in that case and the user experience
is also not good :-)
Almost all BUG_ON instances can be converted to
WARN_ON with a few lines of appropriate error
handling, so do that instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some customers use 0x6C world regulatory domain and this patch
adds the support.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In http://lkml.indiana.edu/hypermail/linux/kernel/1104.1/01955.html, Geerti
Uytterhoeven reports the following warnings for the rtlwifi drivers.
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index_old' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_extreg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_reg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'chnlgroup' may be used uninitialized in this function: => 205
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'u4_regvalue' may be used uninitialized in this function: => 450
src/drivers/net/wireless/rtlwifi/rtl8192cu/hw.c: warning:
'hq_sele' may be used uninitialized in this function: => 924
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function name sounds like checking for existing BA
stream. The function actually checks if we have room for
creating new BA stream or not.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some function parameters become useless after previous
cleanup changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return statement at the last line of a void function
is not necessary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EEPROM version 5.0 adds a new field for disabling AES support, having
an older version means that AES is present. This patch fixes hw AES
crypto support on AR5312 boards, which have an older EEPROM version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AHB, the calibration data usually does not contain a valid MAC address,
the correct MAC address is stored in the board config.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a dual-radio dual-band AR5312 device, the calibration data is shared
between the 5 GHz and the 2.4 GHz radio/MAC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, you get this:
CC [M] drivers/net/wireless/ath/ath9k/hif_usb.o
drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’:
drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’
make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1
make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2
make: *** [drivers/net/wireless/ath/] Error 2
The TX_STAT_INC macro should probably be changed to accomodate such
usage, although using a trinary operator in place of an if-else seems
questionable to me anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
New debugfs files:
<debugfs_root>/ath9k_htc/<phy#>/tgt_int_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_tx_stats
<debugfs_root>/ath9k_htc/<phy#>/tgt_rx_stats
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission needs to involve as little latency
as possible after receiving a SWBA event from the target.
Since packets are buffered to use TX stream mode, beacon
frames sometimes gets queued up and are not sent out immediately.
Fix this by decoupling management frame transmission from the
normal data path and send them out immediately.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally, a WMI event would arrive ahead of the TX
URB completion handler. Discarding these events would exhaust
the available TX slots, so handle them by running a timer
cleaning up such events. Also, timeout packets for which TX
completion events have not arrived.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the infrastructure is in place, process WMI
TX status events and complete packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station entry is removed, there could still be
pending packets destined for that station in the HIF layer.
Sending these to the target is not necessary, so drain them
in the driver itself.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point in looping over all the endpoints,
since the HIF layer uses the start/stop APIs only
for the TX pipe. Simplify the API accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing a channel set or a reset operation the pending
frames queued up for transmission have to be flushed and
sent to mac80211. Fixing this has to be done in two separate
steps:
* Flush queued frames and kill the URB TX completion handler.
* Complete all the frames that in the TX pending queue.
This patch adds proper support for draining and all the callsites
namely, channel change/reset/idle/stop are fixed. A separate queue
is used for handling failed frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maintain a bitmap of slots for transmission and update
the cookie field for every packet with the slot value.
This value would be used for matching packets when TX
completion processing is added.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do endpoint header removal in the ISR.
Also, this is needed when TX slot management is added later on.
Use a helper function to strip the driver header.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new routine that takes an endpoint explicitly is
introduced. The normal htc_send() now retrieves the endpoint
from the packet's private data. This would be useful
in TX completion when the endpoint ID would be required.
While at it, use a helper function to map the queue to endpoint.
Data/mgmt/beacon packets use htc_send(), while WMI comamnds
pass the endpoint to HTC.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle queue start/stop properly by maintaining
a counter to check if the pending frame count has
exceeded the threshold. Otherwise, packets would be
dropped needlessly. While at it, use a simple flag
to track queue status and use helper functions too.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using a single URB for receiving WMI events is
insufficient, increase it to 64 to not lose
WMI events in high throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This event will be generated by the target for packet completions.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new cookie field that would be filled by the host.
This can be used to match the TX status WMI event with
the appropriate packet.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current max queue length of 1024 is quite large
and unnecessary. 256 suffices well enough even for high
throughput situations.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For all packets sent through the USB_WLAN_TX_PIPE endpoint,
the private area of the SKB's tx_info can be used to store
driver-specific information. For packets sent through USB_REG_OUT_PIPE,
this will not make a difference since they are routed through a
separate routine that doesn't access the private region.
This would help in situations where TX information is required
in the URB callback.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the received SKB could be equal to
HTC_RX_FRAME_HEADER_SIZE in case of packets with phy/crc errors,
in which case they are dropped without being processed.
Fix this check so that the error counters are updated correctly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a queue to handle WMI events and schedule a tasklet
to process the events. This fixes the race between the
WMI event ISR and the SWBA tasklet when the arrival of
WMI events in quick succession could overwrite the SWBA
data before the tasklet from a previous iteration could
have been scheduled. Also, drain the WMI queue properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transmission of beacons becomes erratic when TX load
is high, since the latency involved in the generation
of a SWBA interrupt on the target to the actual sending
of a beacon is quite high for USB devices.
Fix this by adjusting the beacon response time.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the CAB endpoint to send buffered multicast or
broadcast frames after each SWBA event.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set operating parameters (cwmin, cwmax) for the beacon queue
in AP mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi-interface mode, beacons/probe responses that are
sent out must have their timestamp field updated. Calculate
the TSF adjustment value for each beaconing interface and set it
in the frame properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ampdu stream is created on the first qos packet to an
HT sta. The overhead of setting up the BA session may not be
justified if the outgoing packet rate is minimal (e.g., ping). So
we only allow ampdu streams after seeing a critical number of
packets in an arbitrary one-second interval.
Based on work by Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to enable all the interrupts in mwl8k_probe_hw.
We need to enable only MWL8K_A2H_INT_OPC_DONE interrupt for sending
commands to the firmware. Keep the other interrupts masked in
mwl8k_probe_hw. Also, in mwl8k_start, where we expect other interrupts,
enable only those interrupts we are interested in.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the device id in the platform driver is hardcoded to an id
which is specific to AR9130/AR9132 SOCs as it supports only wmac (wireless mac)
of these SOCs. But this needs to be dynamic when we want to support different
wmac of SOCs. So add id_table to driver to make it extendable to more SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192ce does not initialize the LED correctly.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check whether index is within bounds before testing the element
Both spurChans arrays in modalHeader5G and modalHeader2G have 5 elements,
AR_EEPROM_MODAL_SPURS is defined 5. So unless a break occurs, in the
last iteration (i=5) we tried to access spurChansPtr[5] before testing
whether i was within bounds. Fix this.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the rx/tx tasklet is pending, new unnecessary interrupts may arrive.
Decrease the load by temporarily disabling the interrupts until the tasklet
has completed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The pointers to the debugfs entries do not need to be saved, because they
will be recursively removed when the wiphy is unregistered.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reusing the configured retry counts from the skb cb is more efficient than
reloading the data from uncached memory.
Replace ts_longretry (unused) with ts_final_retry which contains the retry
count for the final rate only
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of redundant loads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ACCESS_ONCE to reduce the number of variable reloads on uncached memory
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is no longer necessary for preparing mac80211 tx status
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use local variables to reduce the number of load/store operations on uncached
memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the slot time based on the mac80211 short slot vs long slot setting
instead of just forcing long slot for all CCK-enabled channels.
This slightly improves 802.11g mode performance in in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k uses 8 usec as a sifs time, extracted from the initvals, whereas the
standard requires a sifs time of 10. The difference originates from the fact
that the SIFS register has an offset of 2 usec.
Fix the SIFS time definition to use the standard value of 10 usec and subtract
2 usecs when writing the SIFS register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Subtract the difference in preamble duration (in usec) from the value
returned by ieee80211_generic_frame_duration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During normal operation, minstrel was showing suspicious EWMA probabilities
exceeding 100%. It looks like the tx status reporting in ath5k was not
properly clearing the rate index for rates which were never attempted.
This is caused by uninitialized stale data in the on-stack tx status
information, which is reused when more frames are received.
To fix this, rely on ts->ts_final_idx to select the last attempted rate,
instead of checking whether ts->ts_rate is set.
Additionally, the conversion from the driver rate index back to the
mac80211 rate index can be dropped, as the mac80211 tx status will still
have the original rate index which was used to set up the descriptor.
Additionally, one more inaccuracy was fixed - the final rate attempt
count only needs to be increased by one if the transmission attempt was
successful.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k driver does kmalloc allocations for pcal info in a loop.
But, if one fails it was simply returning -ENOMEM without freeing
already allocated memory. This patch corrects that oversight.
Reported-by: Eugene A. Shatokhin <dame_eugene@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Fix checkpatch errors and warnings comprising of indent errors, spaces and
__packed warnings. Also fix 'make C = 2' warnings.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Older versions have not been sold and the driver does not explicitly
check for them anyway, so we can simply ignore the macRev here.
Reduces ath9k_hw size on mips by more than 2 KB.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update Tx gain 23 for all tx gain table.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export RSSI information from all the control and extension
channel chains to debugfs. Also add rx antenna information
to debugfs. This will be useful for debugging purpose.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_rate_control_register() prints a message at KERN_ERR level. It
looks like it's just a debugging message, so pr_err() seems to be
overdone. But none of the similar functions in drivers/net/wireless
print a message, so let's just drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rx should only be enabled after enough rx buffers have been given to the
hardware, however ath_rx_buf_link was calling ath9k_hw_rxena after every
single added buffer.
Fix this by calling ath9k_hw_rxena directly from the rx tasklet after
completion instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I can't find any valid reason for not setting the ATH9K_RX_FILTER_PSPOLL
flag on older hardware and neither the documentation nor the reference
code mention any reason for excluding older hardware here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having separate key information definitions for
each type of key, a common key information bitmap is used.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before calling host_to_card() to send the cmd to firmware,
we use skb_push() to add 4 bytes SDIO interface header at
the start of the data buffer. Since cmd_skb data structure
will be re-used at a later time, we need to restore its
headroom by removing the 4 bytes header.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function returns true if there is atleast one frame
in any one of the tx queues.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Cc: <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jason Conti <jason.conti@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we maintain API properly, then there isn't
really a reason to warn about this since we'll
just be adding things that are safe to ignore,
so downgrade the warning to debug info level.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no need to keep both normal and BT statistics
versions around all the time in memory when we only
use a subset of both. So keep only the subsets that
we need in memory, depending on the debug config).
Also, in doing so, we can remove all the calls to
iwl_bt_statistics() in the driver as we'll just
access the copied statistics now.
Finally, also remove this call from the one place
where it might still be needed and automatically
detect what kind of statistics the device is sending
based on their size. This way, we don't need to keep
track of which devices do what any more, which is
good since this is subject to change based on the
ucode version (as some ucode even for non-BT devices
will in fact use BT statistics).
Warn upon encountering a statistics command from the
ucode that isn't known, so we will find such issues
earlier in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If change_interface gets invoked during a firmware
restart, it may crash; prevent that from happening
by checking if ctx->vif is assigned.
Additionally, in my initial commit I forgot to set
the vif->p2p variable correctly, so fix that too.
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The microcode may sometimes reject TX frames when
on a radar channel even after we associated as it
clears information during association and needs to
receive a new beacon before allowing that channel
again. This manifests itself as a TX status value
of TX_STATUS_FAIL_PASSIVE_NO_RX. So in this case,
stop the corresponding queue and give the frame
back to mac80211 for retransmission. We start the
queue again when a beacon from the AP is received
which will make the regulatory enforcement in the
device allow transmitting again.
Signed-off-by: Garen Tamrazian <garenx.tamrazian@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
define of firmware filenames use extra macro to build the files name.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This generates a massive reduction in module size:
with debug:
text data bss dec hex filename
670300 13136 420 683856 a6f50 iwlagn.ko (before)
388347 13136 408 401891 621e3 iwlagn.ko (after)
without debug:
text data bss dec hex filename
528575 13072 420 542067 84573 iwlagn.ko (before)
294192 13072 408 307672 4b1d8 iwlagn.ko (after)
This also removes all the IO debug functionality since
it can easily be replaced by tracing, and makes the
code unnecessarily complex.
I haven't done any CPU utilisation measurements, but
given that the hotpaths don't use much IO it is not
likely to have a negative impact; in fact, the size
reduction will reduce cache pressure which possibly
improves performance.
Finally, an unused function or two were removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ISR (interrupt service routine) ops are now
no longer necessary since they are the same for
all devices this driver now handles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use the value in alloc_rxb_page,
so there's no point in keeping it either.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rev_id variable is only printed, we
don't need to store it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_rev variable is used only during init,
so there's no need to keep it around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable is never used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Again, a 4965 specific code path that we no
longer need in iwlagn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We know after loading the ucode whether it will
support PAN or not, so we can also initialise
the cmd_queue variable much earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices newer than 4965 don't actually send
two different versions of the ALIVE command,
so we always had a bug here since before this
patch we copy more data than we got. Remove
the iwl_init_alive_resp struct and don't use
it.
Since we also really don't need to track all
the data received in ALIVE as we only use the
error and log event tables later, we can also
save space by just keeping those and not more
data around in memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous patch left a message talking about
bootstrap, but that's clearly bogus.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some new devices and microcode files will a greater
variety of features, so the TLV-per-feature approach
we took before will quickly make things harder to
manage and increase the file size.
Add a new TLV that has feature flags. Currently, it
will contain:
1) a PAN feature flag, which moves from a separate
TLV
2) a new BT stats bit that indicates whether the
microcode image uses bluetooth statistics
3) a new MFP flag for management frame protection
which can be enabled once the device/microcode
supports it
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In alive notify, we should check return code instead of assume everything ok
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was used only on 4965 in conjunction with
the bootstrap ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode restart has to take into account a number
of things, like clearing the HCMD_ACTIVE and other
status bits, and waking up the wait_command_queue.
Currently, however, there are a number of places
that neither do that, nor actually set the FW error
bit that leads to proper restart handling, which
means that in those cases things will probably just
hang completely.
To clean this up, make all ucode restart go through
a single function, except for the cases where it's
called during firmware loading.
Also fix a bug in wimax coexist restart avoidance,
it needs to first clear the status bits (and it has
to clear the HCMD_ACTIVE one as well) and then wake
up anything waiting on wait_command_queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 4965 had a bootstrap microcode image, so
the agn driver can completely ignore that and
we can remove some code from it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we loaded a ucode, there's no point in
checking any one that is present, we know
which one is supposed to be present so also
verify that it is exactly the right one.
That also simplifies the code and makes it
faster since it doesn't have to check all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in iwlcore_verify_inst_sparse really
doesn't need to keep track of the number of
errors it encountered since a single one is
fatal.
Also, the code in iwl_verify_inst_full is just
used to print out some things, so rename it to
iwl_print_inst and don't give it a return code
and just make it print out the values.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In alive notification call, return the status from iwl_send_calib_results()
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A number of places just use a variable to return
it right away, which is useless, so let's remove
the variables there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All agn devices behave the same, so there's no
need to go through function pointers for any
of the ucode loading functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that these handlers are no longer shared
between 4965 and agn, they can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver was split, a bunch of definitions
for the 3945 and 4965 devices stayed around, but
they're now useless so remove (some of) them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some code was removed, but a variable it used
and that is now unused stayed around, kill it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of configuring tx power unconditionally, check for
IEEE80211_CONF_CHANGE_POWER and configure it only when stack
sets this flag
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now bssid/aid is overridden with recently changed vif's
bss config. This may cause improper beacon updation due to
bssid/aid mismatch. On station mode, select an associated
sta vif as primary vif and configure that vif's bss into hw.
Update the primary vif on interface change and bss info change.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The present check denies the IBSS interface addtion if we
already have any other vifs. But it fails to deny interface
addition if IBSS was already present.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Nokia N900 the wl1251 consumes the most power when the interface is up
but not associated to access point (that supports PSM). In terms of battery
current consumption, the consumption is ~180 mA higher when the interface is
up but not associated and only ~5 mA higher when associated compared to
interface down and driver not loaded cases.
This patch adds support for the mac80211 idle notifications. Chip is put into
idle very much the same way when entering into PSM by utilizing the Extreme
Low Power (ELP) mode. I.e. idle is entered by setting necessary conditions
in wl1251_ps_set_mode followed by a call to wl1251_ps_elp_sleep.
It seems it is just enough the authorize ELP mode followed by
CMD_DISCONNECT (thanks to Kalle Valo about the idea to use it).
Without disconnect command the chip remains somewhat active and stays
consuming ~20 mA. Idle mode is left by same way than PSM. The wl1251_join
call is used to revert the CMD_DISCONNECT. Without it association to AP
doesn't work when trying second time.
With this patch the interface up but not associated case the battery current
consumption is less than 1 mA higher compared to interface down case.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFC for WL1251 idle mode support brought a few issues that are worth to
update before adding the idle mode support.
Since the idle mode can reuse the code that is now used in Power Save Mode
(PSM), the flag psm in struct wl1251 is changed to variable station_mode
to be able to distinguish between PSM and idle modes.
As the station mode is different than the power power save mode command
that is sent to chip, the enum wl1251_cmd_ps_mod values are used only when
communicating with the chip and new enum wl1251_station_mode values are used
inside the driver.
Confusing comment about psm and elp relation is removed since the PSM is
actually activated by putting the chip into Entreme Low Power (ELP) mode.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With compat-wireless CR* macros in zd_usb.h conflict with CR macros in
include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*.
Conversion was done with using sed and then 'over 80 character line'
checkpatch.pl warnings and comment indents were fixed.
Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing wpa_supplicant with 'nl80211' driver to connect
to an AP with WPA/WPA2 security, we notice the followings:
1) add_key is called firstly with the key from cfg80211
2) set_defaut_key is called next
set_default_key() is specific to WEP keys and should not be
called in case of WPA/WPA2 security. The set_default_key()
won't be called if wpa_supplicant uses "-Dwext" option,
but it's been called if "-Dnl80211" option is specified.
We can fix this issue by adding a check to return from
set_default_key() if WEP key is not configured.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
On the way fix whitespace.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the mwl8k driver attempts and fails to switch from sta to ap
firmware (or vice-versa) in the mwl8k_add_interface routine, the
mwl8k_stop routine will be called. This routine must not attempt
to free the irq if it was not requested.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least EEPROM version 0x11A has the wrong
number of chains programmed into it for some
reason, so we need to override in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These macros are leftover of previous cleanup patches.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct mwifiex_802_11_fixed_ies is not necessary.
struct mwifiex_event_wep_icv_err is not used any more.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove redundant structures and unused macros
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions are no longer used after previous cleanups.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio_on variable is defined but never used.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace them with NL80211_AUTHTYPE_ macros
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace them with NL80211_IFTYPE_ macros
Also remove redundant functions mwifiex_drv_get_mode()
and mwifiex_bss_ioctl_mode().
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already tell mac80211 to stop the queue when we hit a certain
threshold. Hence, it shouldn't happen at all that a frame gets queued
for tx on a full queue. Add an error message for this case.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
rt2x00 should send a BlockAckReq if the transmission of an AMPDU
subframe fails.
Introduce a new flag TXDONE_AMPDU to indicate that this is an AMPDU
subframe and pass IEEE80211_TX_STAT_AMPDU_NO_BACK to mac80211 if an
AMPDU subframe failed during transmission.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STBC transmissions rt2x00 used the number of RxSTBC streams the
destination STA indicates in its HT capabilities as STBC value in
the TXWI.
However, the legacy drivers and our own comment in rt2800.h suggest
that the STBC field in the TXWI only allows a value of 0 or 1.
The values 2 and 3 are reserved (probably for future devices).
And indeed, STBC transmissions to STAs indicating more then 1
RxSTBC stream fail when the STBC field is set to something >1.
Fix this by only setting the STBC field to 1 when STBC should be
used.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices should adjust their tx power in accordance with the
eeproms temperature calibration values. Add a new driver callback
gain_calibration that is called every 4 seconds.
The rt2800 gain calibration routine simply runs the tx power
configuration that takes care of calculating the temperature
compensation delta.
We don't need to synchronize the calls to rt2800_config_txpower
as they should all happen from mac80211's single threaded workqueue.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit d1c3a37cee ("mac80211:
clarify alignment docs, fix up alignment") removed the requirement
for a 4-byte aligned payload rt2x00queue_align_payload is obsolete
as mac80211 will align the payload when it passes the frame to the
net stack.
As a result we can remove the call to rt2x00queue_align_payload in the
rx path and since that's the last user we can remove
rt2x00queue_align_payload altogether.
One advantage is that we save some alignment operations for frames
that don't need to be aligned (for example beause they are not passed
to the net stack).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the indention in rt2800_compesate_txpower and also fix a typo in
the function name rt2800_compesate_txpower -> rt2800_compensate_txpower.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the HT40 tx power compensation value was calculated for each
rate. However, the calculation is independent of the tx rate and as such
can be precalculated and just passed in for each rate.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the HT40 check inside the calculation function to make it easier
for a later cleanup.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simply check if the driver registered the watchdog callback.
There's no need to have an additional flag for that.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the tx status fifo size as 512 calculate it based
on the number of tx queues and the number of entries per queue. Also
round the size up to a power of 2 as kfifo would otherwise round it
down.
On rt2800pci this will increase the kfifo size from 512 bytes to 1024
bytes which is then able to hold the tx status for all entries in all
tx queues.
Furthermore, if the number of tx queues or tx entries changes in the
future (use of the MGMT queue for example) the kfifo size doesn't need
to be updated.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reporting an unlimited number of tx status reports to
mac80211 stop after 16 frames and reschedule the tx status tasklet.
This allows other tasklets to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of receiving an unlimited number of frames, stop after 16
entries and reschedule the rxdone tasklet. This allows other tasklets
to be run inbetween.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some unused variables and correct spelling errors.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw_dot_11n_dev_cap reported by firmware hw_spec
has different format than the 11n capabilities.
Hence a lot of SET_ and RESET_ bit operation macros
were used to convert the dev_cap format to 11n
capability format. However the locally defined 11n
ht_cap macros are not necessary as we can use
IEEE80211_HT_CAP_ macros directly.
The 32-bit dev_cap bitmap is added as comment to
explain the mapping between firmware and 11n spec.
Some unused macros and unnecessary adapter variables
are also removed.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
