This adds unaligned memory access support for the following instructions:
mov.w @(disp,PC),Rn
mov.l @(disp,PC),Rn
These instructions are often used on SH2A toolchains.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch just clears the return code for those cases where an
unaligned memory access occurs on branch instructions without a
delay slot.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register. If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM920 and ARM926 save four registers, not three. Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code. Overwriting it is
not a good idea.
We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration. So fix this latent bug.
This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.
If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Only register as an RTC device after the hardware has been
successfully initialized. The RTC class driver will call
back to this driver to read a pending alarm, and other
drivers watching for new devices on the RTC class may
read the RTC time upon registration. Such access might
occur while the RTC is stopped, prior to clearing
pending alarms, etc.
The new ordering also avoids leaving the platform
device drvdata set to an unregistered struct rtc_device *
on probe errors.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Even though the Linux kernel does not use the tm_isdst field, it is
exposed as part of the ABI. This field can accidentally be left
initialized, which is why we currently memset buffers returned to
userland in rtc_read_time.
There is a case however where the field can return garbage from the
stack though when using the RTC_ALM_READ ioctl on the rtc device. This
ioctl invokes rtc_read_alarm, which is careful to memset the rtc_wkalrm
buffer that is copied to userland, but it then uses a struct copy to
assign to alarm->time given the return value from rtc_ktime_to_tm().
rtc_ktime_to_tm() is implemented by calling rtc_time_to_tm using a
derivative seconds counds from ktime, but rtc_time_to_tm does not assign
a value to ->tm_isdst. This results in garbage from rtc_ktime_to_tm()'s
frame ending up being copied out to userland as part of the returned
rtc_wkalrm.
Fix this by initializing rtc_time->tm_isdst to 0 in rtc_time_to_tm.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
commit 20d5d55149 (OMAP2: PM debug:
remove register dumping) left some code lying around which doesn't
do anything. Clean it up.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
i915: do not setup intel_backlight twice
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: ftdi_sio: add Calao reference board support
USB option driver K3765/K4505 avoid CDC_DATA interface
USB: option: add YUGA device id to driver
usb: s5p-ehci: fix a NULL pointer deference
USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
USB option driver add PID of Huawei Vodafone K4605
USB option driver add PID of Huawei Vodafone K3806
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
usb: musb: gadget: fix error path
usb: gadget: f_phonet: unlock in error case
usb: musb: blackfin: include prefetch head file
usb: musb: tusb6010: fix compilation
usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: musb: cppi: fix build errors due to DBG and missing musb variable
usb: musb: ux500: replace missing DBG with dev_dbg
usb: musb: ux500: set dma config for both src and dst
usb: musb: fix oops on musb_gadget_pullup
usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
usb: gadget: hid: don't STALL when processing a HID Descriptor request
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
omap-serial: Allow IXON and IXOFF to be disabled.
TTY: serial, document ignoring of uart->ops->startup error
TTY: pty, fix pty counting
8250: Fix race condition in serial8250_backup_timeout().
serial/8250_pci: delete duplicate data definition
8250_pci: add support for Rosewill RC-305 4x serial port card
tty: Add "spi:" prefix for spi modalias
atmel_serial: fix atmel_default_console_device
serial: 8250_pnp: add Intermec CV60 touchscreen device
drivers/serial/ucc_uart.c: Fix compiler warning
pch_uart: Set PCIe bus number using probe parameter
serial: samsung: Fix build error
__netpoll_rx() doesnt properly handle skbs with small header
pskb_may_pull() or pskb_trim_rcsum() can change skb->data, we must
reload it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ti_hecc_probe(), the spinlock priv->mbx_lock is not
inited, causing a spinlock lockup BUG.
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ti_hecc_xmit(), local variable "data" is not initialized before
being used.
This initialization got inadvertently removed in the following patch:
can: Unify droping of invalid tx skbs and netdev stats
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build error:
CC drivers/net/sh_eth.o
drivers/net/sh_eth.c:1115: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘sh_eth_interrupt’
drivers/net/sh_eth.c: In function ‘sh_eth_open’:
drivers/net/sh_eth.c:1387: error: implicit declaration of function ‘request_irq’
drivers/net/sh_eth.c:1387: error: ‘sh_eth_interrupt’ undeclared (first use in this function)
drivers/net/sh_eth.c:1387: error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1387: error: for each function it appears in.)
drivers/net/sh_eth.c:1391: error: ‘IRQF_SHARED’ undeclared (first use in this function)
drivers/net/sh_eth.c:1424: error: implicit declaration of function ‘free_irq’
make[2]: *** [drivers/net/sh_eth.o] Error 1
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).
Proposed and tested by Thorsten.
Signed-off-by: Thorsten Schubert <tshu@msc-ge.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] memory hotplug: only unassign assigned increments
[S390] Change default action from reipl to stop for on_restart
[S390] arch/s390/kernel/ipl.c: correct error detection check
[S390] drivers/s390/block/dasd_ioctl.c: add missing kfree
[S390] nss,initrd: kernel image and initrd must be in different segments
According to the SFI specification irq number 0xFF means device has no
interrupt or interrupt attached via GPIO.
Currently, we don't handle this special case and set irq field in
*_board_info structs to 255. It leads to confusion in some drivers.
Accelerometer driver tries to register interrupt 255, fails and prints
"Cannot get IRQ" to dmesg.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (32 commits)
ALSA: hda: Conexant: Allow different output types to share DAC
ASoC: Correct element count for WM8996 sidetone HPF
ASoC: Tegra: wm8903 machine driver: Drop Ventana support
ASoC: Add samsung maintainer
ASoC: Add Springbank I/O card to Speyside Kconfig
ALSA: hda/conexant - Enable ADC-switching for auto-mic mode, too
ALSA: hda - Fix double-headphone/speaker paths for Cxt auto-parser
ALSA: hda - Update jack-sense info even when no automute is set
ALSA: hda - Fix output-path initialization for Realtek auto-parser
sound/soc/fsl/mpc8610_hpcd.c: add missing of_node_put
sound/soc/fsl/p1022_ds.c: add missing of_node_put
sound/soc/ep93xx/ep93xx-i2s.c: add missing kfree
sound/soc/kirkwood/kirkwood-i2s.c: add missing kfree
ASoC: soc-core: use GFP_KERNEL flag for kmalloc in snd_soc_cnew
sound/soc/fsl/fsl_dma.c: add missing of_node_put
ASoC: Clear completions from late WM8996 FLL lock IRQs
ASoC: Clear any outstanding WM8962 FLL lock completions before waiting
ASoC: Ensure we only run Speyside WM8962 bias level callbacks once
ASoC: Fix configuration of WM8996 input enables
ASoC: WM8996 record paths need AIFCLK
...
This bug causes the IECSR register clear failure. In this case, the RETE
(retry error threshold exceeded) interrupt will be generated and cannot be
cleared. So the related ISR may be called persistently.
The RETE bit in IECSR is cleared by writing a 1 to it.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous rtc-s3c had two issues related with its IRQ.
1. Users cannot open rtc multiple times because an open operation
calls request_irq on the same IRQ. (e.g., two user processes wants to
open and read RTC time from rtc-s3c at the same time)
2. If alarm is set and no one has the rtc opened with filesystem
(either the alarm is set by kernel/boot-loader or user set an alarm and
closed rtc dev file), the pending bit is not cleared and no further
interrupt is invoked. When the alarm is used by the system itself such
as a resume from suspend-to-RAM or other Low-power modes/idle, this is
a critical issue.
This patch mitigates these issues by calling request_irq at probe and
free_irq at remove.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bd2802_unregister_led_classdev() should unregister all registered
instances of led_classdev class that had registered by
bd2802_register_led_classdev().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kim Kyuwon <q1.kim@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following build errors:
drivers/tty/serial/8250_early.c:160: error: 'BASE_BAUD' undeclared (first use in this function): 1 errors in 1 logs
drivers/tty/serial/8250_early.c:37:24: error: asm/serial.h: No such file or directory: 1 errors in 1 logs
I am not sure if (1843200 / 16) is suitable for cris, but most other
arch's define it as this value.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 43cc71eed1 ("platform: prefix MODALIAS with "platform:""), the
platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-pwm".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure we are passing the same cookie in all calls to
request_threaded_irq() and free_irq().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an i2c driver, not a platform driver, thus use "i2c" prefix for
the module alias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a callback to do some things after pwm_enable, pwm_disable
and pwm_config.
Signed-off-by: Dilan Lee <dilee@nvidia.com>
Reviewed-by: Robert Morell <rmorell@nvidia.com>
Reviewed-by: Arun Murthy <arun.murthy@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 79dfdaccd1 ("memcg: make oom_lock 0 and 1 based rather than
counter") tried to oom lock the hierarchy and roll back upon
encountering an already locked memcg.
The code is confused when it comes to detecting a locked memcg, though,
so it would fail and rollback after locking one memcg and encountering
an unlocked second one.
The result is that oom-locking hierarchies fails unconditionally and
that every oom killer invocation simply goes to sleep on the oom
waitqueue forever. The tasks practically hang forever without anyone
intervening, possibly holding locks that trip up unrelated tasks, too.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing include of linux/module.h for drivers that use interfaces from
linux/module.h. This patch fixes build errors.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ep93xx_bl.c uses interfaces from linux/module.h, so it should include
that file. This patch fixes build errors:
CC [M] drivers/video/backlight/ep93xx_bl.o
drivers/video/backlight/ep93xx_bl.c:138: error: 'THIS_MODULE' undeclared here (not in a function)
drivers/video/backlight/ep93xx_bl.c:158: error: expected declaration specifiers or '...' before string constant
drivers/video/backlight/ep93xx_bl.c:158: warning: data definition has no type or storage class
...
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace/remove use of RIO v.1.2 registers/bits that are not
forward-compatible with newer versions of RapidIO specification.
RapidIO specification v.1.3 removed Write Port CSR, Doorbell CSR,
Mailbox CSR and Mailbox and Doorbell bits of the PEF CAR.
Use of removed (since RIO v.1.3) register bits affects users of
currently available 1.3 and 2.x compliant devices who may use not so
recent kernel versions.
Removing checks for unsupported bits makes corresponding routines
compatible with all versions of RapidIO specification. Therefore,
backporting makes stable kernel versions compliant with RIO v.1.3 and
later as well.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
