The debugfs file for dumping btcoex parameters unconditionally
assumes a MCI-based device. This will not work for older btcoex
chips. Fix this by branching out the routine into separate
functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2484 Mhz (Japan) usage requires filter coefficients to
be programmed in the CCK TX FIR registers. This is required
for AR9331, AR9485 and AR9462. Fix this and also remove
a few useless macros and a duplicate variable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'|' has higher precedence than ?:. Since AR5K_PHY_TURBO_MODE is 0x1 and
"AR5K_PHY_TURBO_MODE | (ah->ah_radio == AR5K_RF2425)" is true then we
always set turbo to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the code by make use of module_platform_driver macro.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An issue is reported in AR9462 & AR9565 that NF_cal_not_done is
not observed when HW peak detector calibration is disabled. At that
state, the HW is stuck at NF calibration which prevents tx output.
The root cause is wrong peak detector offset calibrated by HW. To
resolve this issue, peak detector calibration is done manually by SW
for AR9462 and AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5% width tolerance for radar patterns defined by ETSI.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As ath6kl firmware can't do intersections the driver should only listen
to regdom changes from cellular base stations, all other requests need to
be refused.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A missing else caused a potential NULL dereference.
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__be32 variables where used a little careless leading to sparse warnings.
Treat them a little more gentle.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just use WARN_ON rather than an if containing only WARN_ON(1).
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the module_usb_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is pretty pointless. Lets kill this to stop people from
thinking that its actually used. Maybe we should go on
a crusade and kill this completely from the kernel.
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free instance of pattern detector if requested DFS domain is
not supported.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_domain() is already defined in /arch/arm/asm/domain.h
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A negative buffer size doesn't make sense and it breaks this check in
ar5523_get_max_rxsz():
if (!ar->rxbufsz || ar->rxbufsz > AR5523_SANE_RXBUFSZ) { ...
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduced the power consumption to half in full and network sleep.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reduced the power consumption to half in full and network sleep.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.
The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170_handle_mpdu is the final part of the
rx path of the driver. It splits the raw data
streams from the device into skb packets and
passes them on to mac80211. As a result of
continuous updates, it grew over the years when
new code was added by the following commits:
- report A-MPDU status
- fix HT peer BA session corruption
- A-MPDU frame type filter
- ...
This patch splits the routine into two stages.
The first stage only deals with the details
about extracting and verifying the data from
the incoming stream. Whereas the second stage
packs it into skbs and passes it on to mac80211.
Reported-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several people have complained about an unusual
and undocumented feature of the AR9170 hardware:
In siffer mode, the hardware generates spurious
ACK frames for every received frame... even
broadcasts.
The reason for this malfunction is unknown:
<http://marc.info/?l=linux-wireless&m=134517238506033>
But there's a workaround: Instead of the special
sniffer mode, the hardware will be put into
station mode and all rx filters are disabled.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marco Fonseca <marco@tampabay.rr.com>
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
