Make some changes to the NEED_RESCHED and POLLING_NRFLAG to reduce
confusion, and make their semantics rigid. Improves efficiency of
resched_task and some cpu_idle routines.
* In resched_task:
- TIF_NEED_RESCHED is only cleared with the task's runqueue lock held,
and as we hold it during resched_task, then there is no need for an
atomic test and set there. The only other time this should be set is
when the task's quantum expires, in the timer interrupt - this is
protected against because the rq lock is irq-safe.
- If TIF_NEED_RESCHED is set, then we don't need to do anything. It
won't get unset until the task get's schedule()d off.
- If we are running on the same CPU as the task we resched, then set
TIF_NEED_RESCHED and no further action is required.
- If we are running on another CPU, and TIF_POLLING_NRFLAG is *not* set
after TIF_NEED_RESCHED has been set, then we need to send an IPI.
Using these rules, we are able to remove the test and set operation in
resched_task, and make clear the previously vague semantics of
POLLING_NRFLAG.
* In idle routines:
- Enter cpu_idle with preempt disabled. When the need_resched() condition
becomes true, explicitly call schedule(). This makes things a bit clearer
(IMO), but haven't updated all architectures yet.
- Many do a test and clear of TIF_NEED_RESCHED for some reason. According
to the resched_task rules, this isn't needed (and actually breaks the
assumption that TIF_NEED_RESCHED is only cleared with the runqueue lock
held). So remove that. Generally one less locked memory op when switching
to the idle thread.
- Many idle routines clear TIF_POLLING_NRFLAG, and only set it in the inner
most polling idle loops. The above resched_task semantics allow it to be
set until before the last time need_resched() is checked before going into
a halt requiring interrupt wakeup.
Many idle routines simply never enter such a halt, and so POLLING_NRFLAG
can be always left set, completely eliminating resched IPIs when rescheduling
the idle task.
POLLING_NRFLAG width can be increased, to reduce the chance of resched IPIs.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Con Kolivas <kernel@kolivas.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Run idle threads with preempt disabled.
Also corrected a bugs in arm26's cpu_idle (make it actually call schedule()).
How did it ever work before?
Might fix the CPU hotplugging hang which Nigel Cunningham noted.
We think the bug hits if the idle thread is preempted after checking
need_resched() and before going to sleep, then the CPU offlined.
After calling stop_machine_run, the CPU eventually returns from preemption and
into the idle thread and goes to sleep. The CPU will continue executing
previous idle and have no chance to call play_dead.
By disabling preemption until we are ready to explicitly schedule, this bug is
fixed and the idle threads generally become more robust.
From: alexs <ashepard@u.washington.edu>
PPC build fix
From: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
MIPS build fix
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures define and use this type in their compat_ioctl code, but
all of them can easily use the identical ioctl_trans_handler_t type that is
defined in common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64 translates normal loads and stores to special MMIO regions into I/O port
accesses. Reserve these special MMIO regions in /proc/iomem.
Sample /proc/iomem:
f8100000000-f81003fffff : PCI Bus 0000:80 I/O Ports 00000000-00000fff
f8100400000-f81007fffff : PCI Bus 0000:8e I/O Ports 00001000-00001fff
f8100800000-f8100ffffff : PCI Bus 0000:9c I/O Ports 00002000-00003fff
f8101000000-f81017fffff : PCI Bus 0000:aa I/O Ports 00004000-00005fff
and corresponding /proc/ioports:
00000000-00000fff : PCI Bus 0000:80
00001000-00001fff : PCI Bus 0000:8e
00002000-00003fff : PCI Bus 0000:9c
00004000-00005fff : PCI Bus 0000:aa
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When a page has a memory uncorrectable ECC error, the recovery
code wants to prevent the page from being reused. This change
bumps the reference count to prevent the page from getting back
on the free list.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
paddr needs to be shifted by PAGE_SHIFT to be valid
input for pfn_valid().
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The determination of whether an MCA is recoverable or not must
be based on the bits set in the PSP (Processor State Parameter).
The specific bits are shown in the Intel IA-64 Architecture Software
Developer's Manual, Vol 2, Table 11-6 Software Recovery Bits in
Processor State Parameter. Those bits should be consistent
across the entire IA-64 family of processors.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
At the moment, attempting to invoke a signal-handler on the normal
stack is guaranteed to fail if the stack-pointer happens not to be
16-byte aligned. This is because the signal-trampoline will attempt
to store fp-regs with stf.spill instructions, which will trap for
misaligned addresses. This isn't terribly useful behavior. It's
better to just always align the signal frame to the next lower 16-byte
boundary.
Signed-off-by: David Mosberger-Tang <David.Mosberger@acm.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The original memory less node allocation attempted to use NODEDATA_ALIGN for
alignment. The bootmem allocator only allows a power of two alignments. This
causes a BUG_ON for some nodes. For cpu only nodes just allocate with a
PERCPU_PAGE_SIZE alignment.
Some older firmware reports SLIT distances of 0xff and results in bestnode
not being computed. This is now treated correctly.
The failed allocation check was removed because it's redundant. The
bootmem allocator already makes this check.
This fix has been boot tested on 4 node machine which has 4 cpu only nodes
and 1 memory node. Thanks to Pete Keilty for reporting this and helping me
test it.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
notify_die() added for MCA_{MONARCH,SLAVE,RENDEZVOUS}_{ENTER,PROCESS,LEAVE} and
INIT_{MONARCH,SLAVE}_{ENTER,PROCESS,LEAVE}. We need multiple
notification points for these events because they can take many seconds
to run which has nasty effects on the behaviour of the rest of the
system.
DIE_SS replaced by a generic DIE_FAULT which checks the vector number,
to allow interception of faults other than SS.
DIE_MACHINE_{HALT,RESTART} added to allow last minute close down
processing, especially when the halt/restart routines are called from
error handlers.
DIE_OOPS added.
The check for kprobe's break numbers has been moved from traps.c to
kprobes.c, allowing DIE_BREAK to be used for any additional break
numbers, i.e. it is no longer kprobes specific.
Hooks for kernel debuggers and kernel dumpers added, ENTER and LEAVE.
Both of these disable the system for long periods which impact on
watchdogs and heartbeat systems in general. More patches to come that
use these events to reset watchdogs and heartbeats.
unregister_die_notifier() added and both routines exported. Requested
by Dean Nelson.
Lock removed from {un,}register_die_notifier. notifier_chain_register()
already takes a lock. Also the generic notifier chain locking is being
reworked to distinguish between callbacks that can block and those that
cannot, the lock in {un,}register_die_notifier would interfere with
that change. http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
Leading white space removed from arch/ia64/kernel/kprobes.c.
Typo in mca.c in original version of this patch found & fixed by Dean
Nelson.
Signed-off-by: Keith Owens <kaos@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Acked-by: Anil Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is the arch/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in arch/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reorganize the preempt_disable/enable calls to eliminate the extra preempt
depth. Changes based on Paul McKenney's review suggestions for the kprobes
RCU changeset.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes to the arch kprobes infrastructure to take advantage of the locking
changes introduced by usage of RCU for synchronization. All handlers are now
run without any locks held, so they have to be re-entrant or provide their own
synchronization.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IA64 changes to track kprobe execution on a per-cpu basis. We now track the
kprobe state machine independently on each cpu using an arch specific kprobe
control block.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following set of patches are aimed at improving kprobes scalability. We
currently serialize kprobe registration, unregistration and handler execution
using a single spinlock - kprobe_lock.
With these changes, kprobe handlers can run without any locks held. It also
allows for simultaneous kprobe handler executions on different processors as
we now track kprobe execution on a per processor basis. It is now necessary
that the handlers be re-entrant since handlers can run concurrently on
multiple processors.
All changes have been tested on i386, ia64, ppc64 and x86_64, while sparc64
has been compile tested only.
The patches can be viewed as 3 logical chunks:
patch 1: Reorder preempt_(dis/en)able calls
patches 2-7: Introduce per_cpu data areas to track kprobe execution
patches 8-9: Use RCU to synchronize kprobe (un)registration and handler
execution.
Thanks to Maneesh Soni, James Keniston and Anil Keshavamurthy for their
review and suggestions. Thanks again to Anil, Hien Nguyen and Kevin Stafford
for testing the patches.
This patch:
Reorder preempt_disable/enable() calls in arch kprobes files in preparation to
introduce locking changes. No functional changes introduced by this patch.
Signed-off-by: Ananth N Mavinakayahanalli <ananth@in.ibm.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton suggested to move kprobes from kernel hacking menu, since
kernel hacking menu is in-appropriate for the Kprobes. This patch moves
Kprobes and Oprofile under instrumentation menu.
(akpm: it's not a natural fit, but things like djprobes and the s390 guys'
statistics library need a home)
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: John Levon <levon@movementarian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current ia64 implementation of dma_get_cache_alignment does not work
for modules because it relies on a symbol which is not exported. Direct
access to a global is a little ugly anyway, so this patch re-implements
dma_get_cache_alignment in a manner similar to what is currently used for
x86_64.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restrict CONFIG_SGI_SN_XP to IA64_GENERIC or IA64_SGI_SN2 kernels.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
wrap_mmu_context(), delayed_tlb_flush(), get_mmu_context() all
have an extra { } block which cause one extra indentation.
get_mmu_context() is particularly bad with 5 indentations to
the most inner "if". It finally gets on my nerve that I can't
keep the code within 80 columns. Remove the extra { } block
and while I'm at it, reformat all the comments to 80-column
friendly. No functional change at all with this patch.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Corrects the very inefficent method of finding free context_ids in
get_mmu_context(). Instead of walking the task_list of all processes,
2 bitmaps are used to efficently store and lookup state, inuse and
needs flushing. The entire rid address space is now used before calling
wrap_mmu_context and global tlb flushing.
Special thanks to Ken and Rohit for their review and modifications in
using a bit flushmap.
Signed-off-by: Peter Keilty <peter.keilty@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define jiffies_64 in kernel/timer.c rather than having 24 duplicated
defines in each architecture.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure we always return, as all syscalls should. Also move the common
prototype to <linux/syscalls.h>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
pgdat->node_size_lock is basically only neeeded in one place in the normal
code: show_mem(), which is the arch-specific sysrq-m printing function.
Strictly speaking, the architectures not doing memory hotplug do no need this
locking in show_mem(). However, they are all included for completeness. This
should also make any future consolidation of all of the implementations a
little more straightforward.
This lock is also held in the sparsemem code during a memory removal, as
sections are invalidated. This is the place there pfn_valid() is made false
for a memory area that's being removed. The lock is only required when doing
pfn_valid() operations on memory which the user does not already have a
reference on the page, such as in show_mem().
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was one small but very significant change in the previous patch:
mprotect's flush_tlb_range fell outside the page_table_lock: as it is in 2.4,
but that doesn't prove it safe in 2.6.
On some architectures flush_tlb_range comes to the same as flush_tlb_mm, which
has always been called from outside page_table_lock in dup_mmap, and is so
proved safe. Others required a deeper audit: I could find no reliance on
page_table_lock in any; but in ia64 and parisc found some code which looks a
bit as if it might want preemption disabled. That won't do any actual harm,
so pending a decision from the maintainers, disable preemption there.
Remove comments on page_table_lock from flush_tlb_mm, flush_tlb_range and
flush_tlb_page entries in cachetlb.txt: they were rather misleading (what
generic code does is different from what usually happens), the rules are now
changing, and it's not yet clear where we'll end up (will the generic
tlb_flush_mmu happen always under lock? never under lock? or sometimes under
and sometimes not?).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
First step in pushing down the page_table_lock. init_mm.page_table_lock has
been used throughout the architectures (usually for ioremap): not to serialize
kernel address space allocation (that's usually vmlist_lock), but because
pud_alloc,pmd_alloc,pte_alloc_kernel expect caller holds it.
Reverse that: don't lock or unlock init_mm.page_table_lock in any of the
architectures; instead rely on pud_alloc,pmd_alloc,pte_alloc_kernel to take
and drop it when allocating a new one, to check lest a racing task already
did. Similarly no page_table_lock in vmalloc's map_vm_area.
Some temporary ugliness in __pud_alloc and __pmd_alloc: since they also handle
user mms, which are converted only by a later patch, for now they have to lock
differently according to whether or not it's init_mm.
If sources get muddled, there's a danger that an arch source taking
init_mm.page_table_lock will be mixed with common source also taking it (or
neither take it). So break the rules and make another change, which should
break the build for such a mismatch: remove the redundant mm arg from
pte_alloc_kernel (ppc64 scrapped its distinct ioremap_mm in 2.6.13).
Exceptions: arm26 used pte_alloc_kernel on user mm, now pte_alloc_map; ia64
used pte_alloc_map on init_mm, now pte_alloc_kernel; parisc had bad args to
pmd_alloc and pte_alloc_kernel in unused USE_HPPA_IOREMAP code; ppc64
map_io_page forgot to unlock on failure; ppc mmu_mapin_ram and ppc64 im_free
took page_table_lock for no good reason.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia64 has expand_backing_store function for growing its Register Backing Store
vma upwards. But more complete code for this purpose is found in the
CONFIG_STACK_GROWSUP part of mm/mmap.c. Uglify its #ifdefs further to provide
expand_upwards for ia64 as well as expand_stack for parisc.
The Register Backing Store vma should be marked VM_ACCOUNT. Implement the
intention of growing it only a page at a time, instead of passing an address
outside of the vma to handle_mm_fault, with unknown consequences.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The original vm_stat_account has fallen into disuse, with only one user, and
only one user of vm_stat_unaccount. It's easier to keep track if we convert
them all to __vm_stat_account, then free it from its __shackles.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... and related annotations for amd64 - swiotlb code is shared, but
prototypes are not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In arch/ia64/kernel/ptrace.c there is a test for a peek or poke of a
register image (in register backing storage).
The test can be unnecessarily long (and occurs while holding the tasklist_lock).
Especially long on a large system with thousands of active tasks.
The ptrace caller (presumably a debugger) specifies the pid of
its target and an address to peek or poke. But the debugger could be
attached to several tasks.
The idea of find_thread_for_addr() is to find whether the target address
is in the RBS for any of those tasks.
Currently it searches the thread-list of the target pid. If that search
does not find a match, and the shared mm-struct's user count indicates
that there are other tasks sharing this address space (a rare occurrence),
a search is made of all the tasks in the system.
Another approach can drastically shorten this procedure.
It depends upon the fact that in order to peek or poke from/to any task,
the debugger must first attach to that task. And when it does, the
attached task is made a child of the debugger (is chained to its children list).
Therefore we can search just the debugger's children list.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
flush_tlb_all() can be a scaling issue on large SGI Altix systems
since it uses the global call_lock and always executes on all cpus.
When a process enters flush_tlb_range() to purge TLBs for another
process, it is possible to avoid flush_tlb_all() and instead allow
sn2_global_tlb_purge() to purge TLBs only where necessary.
This patch modifies flush_tlb_range() so that this case can be handled
by platform TLB purge functions and updates ia64_global_tlb_purge()
accordingly. sn2_global_tlb_purge() now calculates the region register
value from the mm argument introduced with this patch.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte_copy() calls calls get_nasid(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead.
It is OK if we migrate off node.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Eliminate the passing in of a scratch buffer used for locating the
reserved page setup for XPC.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
XPC needs to be changed to support up to 16k nasids on an SGI Altix system.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch addresses a few issues with the open/close protocol that
were revealed by the newly added disengage functionality combined
with more extensive testing.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In arch/ia64 change the explicit use of a for-loop using NR_CPUS into the
general for_each_online_cpu() construct. This widens the scope of potential
future optimizations of the general constructs, as well as takes advantage
of the existing optimizations of first_cpu() and next_cpu(), which is
advantageous when the true CPU count is much smaller than NR_CPUS.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In arch/ia64 change the explicit use of for-loops and NR_CPUS into the
general for_each_cpu() or for_each_online_cpu() constructs, as
appropriate. This widens the scope of potential future optimizations
of the general constructs, as well as takes advantage of the existing
optimizations of first_cpu() and next_cpu().
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The new ia64 assembler uses slot 1 for the offset of a long (2-slot)
instruction and the old assembler uses slot 2. The 2.6 kernel assumes
slot 2 and won't boot when the new assembler is used:
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1433
This patch will work with either slot 1 or 2.
Patch provided by H.J. Lu
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the "siblings" field value in /proc/cpuinfo so that it now shows the
number of siblings as seen by OS, instead of what is available from
hardware perspective.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The simscsi code at present overflows an int if it's given a large
disk image. The attached patch increases the possible size to 128G.
While it's unlikely that anyone will want to use SKI with such a
large drive, the same framework is currently being used for various
virtualisation experiments.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
changes to swiotlb.c made in commit 281dd25cdc
since this file has been moved from arch/ia64/lib/swiotlb.c to
lib/swiotlb.c
Signed-off-by: Tony Luck <tony.luck@intel.com>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've noticed a kernel hang during a storm of CMC interrupts, which was
tracked down to the continual execution of the interrupt handler.
There's code in the CMC handler that's supposed to disable CMC
interrupts and switch to polling mode when it sees a bunch of CMCs.
Because disabling CMCs across all CPUs isn't safe in interrupt context,
the disable is done with a schedule_work(). But with continual CMC
interrupts, the schedule_work() never gets executed.
The following patch immediately disables CMC interrupts for the current
CPU. This then allows (at least) one CPU to ignore CMC interrupts,
execute the schedule_work() code, and disable CMC interrupts on the rest
of the CPUs.
Acked-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Bryan Sutula <Bryan.Sutula@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
gensparse_defconfig is a config generated file for SPARSEMEM and GENERIC
kernel configuration (defconfig).
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is the minimal set of changes required by ia64 to use SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
For FLATMEM contig_page_data has been made transparent to the arch code.
This patch conforms to that change.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The patch modifies the Kconfig file to introduce the new memory model
options and other related SPARSEMEM changes. There is also a minor change
in the Makefile.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The swiotlb implementation is shared by both IA-64 and EM64T. However,
the source itself lives under arch/ia64. This patch moves swiotlb.c
from arch/ia64/lib to lib/ and fixes-up the appropriate Makefile and
Kconfig files. No actual changes are made to swiotlb.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
/proc/iomem describes a block of memory as "Kernel data",
but the end address is derived from "_edata". The kernel
actually has many other sections beyond _edata. Get the
real end address from _end.
Acked-by: Khalid Aziz <khalid_aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds a #define for SN_SAL_IOIF_PCI_SAFE and makes that the
preferred method of implementing sn_pci_legacy_read() and
sn_pci_legacy_write().
This SAL call has been present in SGI proms since version 4.10. If the
SN_SAL_IOIF_PCI_SAFE call fails, revert to the previous code for compatability
with older proms.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Address space resources for ACPI devices have a producer/consumer
flag. All devices "consume" the indicated address space. If the
resource is marked as a "producer", the range is also passed on
to child devices.
We currently ignore this flag when setting up MMIO and I/O port
windows for PCI root bridges, so we could mistakenly interpret
a "consumed-only" range, like CSR space for the device itself,
as a window that is routed to children.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Verify the pfn is valid before calling pfn_to_page(),
and cut isolation message if nothing was done.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Wire the MCA/INIT handler stacks into DTR[2] and track them in
IA64_KR(CURRENT_STACK). This gives the MCA/INIT handler stacks the
same TLB status as normal kernel stacks. Reload the old CURRENT_STACK
data on return from OS to SAL.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sd driver now uses scsi_execute_req() for almost everything.
scsi_execute_req() converts requests into scatterlists.
Fix the HP SCSI disk simulator to understand scatterlists for
more commands.
Without this patch the current kernel will not boot on the simulator
(the disks are always detected as having no sectors, and so cannot be
mounted).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Move acpi_map_iosapics() from pci.c to acpi.c, since it doesn't
have anything to do with PCI.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update comment about how ar.k0 is used. Make the initialization the
same as in start_secondary() (no functional change, just make it look
more similar).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
User mode kexec tools expect to find information about physical
memory in /proc/iomem (as they do on x86) to validate the addresses
that the new kernel will use.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
With the new fdtable locking rules, you have to protect fdtable with either
->file_lock or rcu_read_lock/unlock(). There are some places where we
aren't doing either. This patch fixes those places.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch increases the maximum number of cpus supported on IA64
to 1024. No changes are made to the default SSI size. The patch
simply allows specifying up to 1024p.
There are certainly scaling (& other) issues that also need to be
addressed!!! Additional patches will follow.....
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There were some trailing white spaces, long lines, brackets in
weird style etc. This patch cleans them up.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch removes some compilation warnings, mostly
trivially. acpi.c fix also noted by Kenji Kaneshige.
Signed-off-by; Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Some of the SN code & #defines related to compact nodes & IO discovery
have gotten stale over the years. This patch attempts to clean them up.
Some of the various SN MAX_xxx #defines were also unclear & misused.
The primary changes are:
- use MAX_NUMNODES. This is the generic linux #define for the number
of nodes that are known to the generic kernel. Arrays & loops
for constructs that are 1:1 with linux-defined nodes should
use the linux #define - not an SN equivalent.
- use MAX_COMPACT_NODES for MAX_NUMNODES + NUM_TIOS. This is the
number of nodes in the SSI system. Compact nodes are a hack to
get around the IA64 architectural limit of 256 nodes. Large SGI
systems have more than 256 nodes. When we upgrade to ACPI3.0,
I _hope_ that all nodes will be real nodes that are known to
the generic kernel. That will allow us to delete the notion
of "compact nodes".
- add MAX_NUMALINK_NODES for the total number of nodes that
are in the numalink domain - all partitions.
- simplified (understandable) scan_for_ionodes()
- small amount of cleanup related to cnodes
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
PNP and PNPACPI turned on
i8042 recently changed from ACPI to PNP detection. Without PNP, it
probes legacy I/O ports for the keyboard controller, which causes an
MCA on HP boxes.
Also, I'm about to remove 8250_acpi.c, so we'll need PNP to detect
non-PCI serial ports. Until 8250_acpi.c is removed, some systems
will see serial ports reported twice (once from 8250_acpi.c and again
from 8250_pnp.c). This is harmless.
PNPACPI is still marked EXPERIMENTAL, but I'm not aware of any
outstanding issues on ia64.
IDE_GENERIC turned off (except for SGI simulator, all ia64 IDE is PCI)
ide-generic probes compiled-in legacy I/O ports for IDE devices, which
again causes an MCA. It would be nicer to just get rid of all the
legacy junk from include/asm-ia64/ide.h, but that is a bit riskier
because it could break ide-cs and the HDIO_REGISTER_HWIF ioctl
(http://www.ussg.iu.edu/hypermail/linux/kernel/0508.2/0049.html).
Here's the essence of the patch:
-# CONFIG_PNP is not set
+CONFIG_PNP=y
+CONFIG_PNPACPI=y
-CONFIG_IDE_GENERIC=y
+# CONFIG_IDE_GENERIC is not set
Tested on tiger, bigsur, and zx1.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Several implementations were essentialy a common piece of C code using
the cmpxchg() macro. Put the implementation in one spot that everyone
can share, and convert sparc64 over to using this.
Alpha is the lone arch-specific implementation, which codes up a
special fast path for the common case in order to avoid GP reloading
which a pure C version would require.
Signed-off-by: David S. Miller <davem@davemloft.net>
Machine vector selection has always been a bit of a hack given how
early in system boot it needs to be done. Services like ACPI namespace
are not available and there are non-trivial problems to moving them to
early boot. However, there's no reason we can't change to a different
machvec later in boot when the services we need are available. By
adding a entry point for later initialization of the swiotlb, we can add
an error path for the hpzx1 machevec initialization and fall back to the
DIG machine vector if IOMMU hardware isn't found in the system. Since
ia64 uses 4GB for zone DMA (no ISA support), it's trivial to allocate a
contiguous range from the slab for bounce buffer usage.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pavel Emelianov and Kirill Korotaev observe that fs and arch users of
security_vm_enough_memory tend to forget to vm_unacct_memory when a
failure occurs further down (typically in setup_arg_pages variants).
These are all users of insert_vm_struct, and that reservation will only
be unaccounted on exit if the vma is marked VM_ACCOUNT: which in some
cases it is (hidden inside VM_STACK_FLAGS) and in some cases it isn't.
So x86_64 32-bit and ppc64 vDSO ELFs have been leaking memory into
Committed_AS each time they're run. But don't add VM_ACCOUNT to them,
it's inappropriate to reserve against the very unlikely case that gdb
be used to COW a vDSO page - we ought to do something about that in
do_wp_page, but there are yet other inconsistencies to be resolved.
The safe and economical way to fix this is to let insert_vm_struct do
the security_vm_enough_memory check when it finds VM_ACCOUNT is set.
And the MIPS irix_brk has been calling security_vm_enough_memory before
calling do_brk which repeats it, doubly accounting and so also leaking.
Remove that, and all the fs and arch calls to security_vm_enough_memory:
give it a less misleading name later on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we use 64bit kernel on ia64/x86_64/s390 architecture, and we run
32bit binary on 32bit compatibility mode, sendfile system call seems be
not set offset argument.
This is because sendfile's return value is not zero but the code regards
the result by return value is zero or not.
This problem will be affect to ia64/x86_64/s390 and not affect to other
architecture does not affect other architecture (mips/parisc/ppc64/sparc64).
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete the special case unwind code that was only used by the old
MCA/INIT handler.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The bulk of the change. Use per cpu MCA/INIT stacks. Change the SAL
to OS state (sos) to be per process. Do all the assembler work on the
MCA/INIT stacks, leaving the original stack alone. Pass per cpu state
data to the C handlers for MCA and INIT, which also means changing the
mca_drv interfaces slightly. Lots of verification on whether the
original stack is usable before converting it to a sleeping process.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reading the INIT record from SAL during the INIT event has proved to be
unreliable, and a source of hangs during INIT processing. The new
MCA/INIT handlers remove the need to get the INIT record from SAL.
Change salinfo.c so mca.c can just flag that a new record is available,
without having to read the record during INIT processing. This patch
can be applied without the new MCA/INIT handlers.
Also clean up some usage of NR_CPUS which should have been using
cpu_online().
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When introducing the generic asm-offsets.h support the dependency
chain for the prepare targets was changed. All build scripts expecting
include/asm/asm-offsets.h to be made when using the prepare target would broke.
With the limited number of prepare targets left in arch Makefiles
the trivial solution was to introduce a new arch specific target: archprepare
The dependency chain looks like this now:
prepare
|
+--> prepare0
|
+--> archprepare
|
+--> scripts_basic
+--> prepare1
|
+---> prepare2
|
+--> prepare3
So prepare 3 is processed before prepare2 etc.
This guaantees that the asm symlink, version.h, scripts_basic
are all updated before archprepare is processed.
prepare0 which build the asm-offsets.h file will need the
actions performed by archprepare.
The head target is now named prepare, because users scripts will most
likely use that target, but prepare-all has been kept for compatibility.
Updated Documentation/kbuild/makefiles.txt.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch (written by me and also containing many suggestions of Arjan van
de Ven) does a major cleanup of the spinlock code. It does the following
things:
- consolidates and enhances the spinlock/rwlock debugging code
- simplifies the asm/spinlock.h files
- encapsulates the raw spinlock type and moves generic spinlock
features (such as ->break_lock) into the generic code.
- cleans up the spinlock code hierarchy to get rid of the spaghetti.
Most notably there's now only a single variant of the debugging code,
located in lib/spinlock_debug.c. (previously we had one SMP debugging
variant per architecture, plus a separate generic one for UP builds)
Also, i've enhanced the rwlock debugging facility, it will now track
write-owners. There is new spinlock-owner/CPU-tracking on SMP builds too.
All locks have lockup detection now, which will work for both soft and hard
spin/rwlock lockups.
The arch-level include files now only contain the minimally necessary
subset of the spinlock code - all the rest that can be generalized now
lives in the generic headers:
include/asm-i386/spinlock_types.h | 16
include/asm-x86_64/spinlock_types.h | 16
I have also split up the various spinlock variants into separate files,
making it easier to see which does what. The new layout is:
SMP | UP
----------------------------|-----------------------------------
asm/spinlock_types_smp.h | linux/spinlock_types_up.h
linux/spinlock_types.h | linux/spinlock_types.h
asm/spinlock_smp.h | linux/spinlock_up.h
linux/spinlock_api_smp.h | linux/spinlock_api_up.h
linux/spinlock.h | linux/spinlock.h
/*
* here's the role of the various spinlock/rwlock related include files:
*
* on SMP builds:
*
* asm/spinlock_types.h: contains the raw_spinlock_t/raw_rwlock_t and the
* initializers
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* asm/spinlock.h: contains the __raw_spin_*()/etc. lowlevel
* implementations, mostly inline assembly code
*
* (also included on UP-debug builds:)
*
* linux/spinlock_api_smp.h:
* contains the prototypes for the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*
* on UP builds:
*
* linux/spinlock_type_up.h:
* contains the generic, simplified UP spinlock type.
* (which is an empty structure on non-debug builds)
*
* linux/spinlock_types.h:
* defines the generic type and initializers
*
* linux/spinlock_up.h:
* contains the __raw_spin_*()/etc. version of UP
* builds. (which are NOPs on non-debug, non-preempt
* builds)
*
* (included on UP-non-debug builds:)
*
* linux/spinlock_api_up.h:
* builds the _spin_*() APIs.
*
* linux/spinlock.h: builds the final spin_*() APIs.
*/
All SMP and UP architectures are converted by this patch.
arm, i386, ia64, ppc, ppc64, s390/s390x, x64 was build-tested via
crosscompilers. m32r, mips, sh, sparc, have not been tested yet, but should
be mostly fine.
From: Grant Grundler <grundler@parisc-linux.org>
Booted and lightly tested on a500-44 (64-bit, SMP kernel, dual CPU).
Builds 32-bit SMP kernel (not booted or tested). I did not try to build
non-SMP kernels. That should be trivial to fix up later if necessary.
I converted bit ops atomic_hash lock to raw_spinlock_t. Doing so avoids
some ugly nesting of linux/*.h and asm/*.h files. Those particular locks
are well tested and contained entirely inside arch specific code. I do NOT
expect any new issues to arise with them.
If someone does ever need to use debug/metrics with them, then they will
need to unravel this hairball between spinlocks, atomic ops, and bit ops
that exist only because parisc has exactly one atomic instruction: LDCW
(load and clear word).
From: "Luck, Tony" <tony.luck@intel.com>
ia64 fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjanv@infradead.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the final 20 DEFINE_SPINLOCK holdouts. (another 580 places
are already using DEFINE_SPINLOCK). Build tested on x86.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order for the RCU to work, the file table array, sets and their sizes must
be updated atomically. Instead of ensuring this through too many memory
barriers, we put the arrays and their sizes in a separate structure. This
patch takes the first step of putting the file table elements in a separate
structure fdtable that is embedded withing files_struct. It also changes all
the users to refer to the file table using files_fdtable() macro. Subsequent
applciation of RCU becomes easier after this.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For architecture like ia64, the switch stack structure is fairly large
(currently 528 bytes). For context switch intensive application, we found
that significant amount of cache misses occurs in switch_to() function.
The following patch adds a hook in the schedule() function to prefetch
switch stack structure as soon as 'next' task is determined. This allows
maximum overlap in prefetch cache lines for that structure.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Delete obsolete stuff from arch Makefile
Rename file to asm-offsets.h
The trick used in the arch Makefile to circumvent the circular
dependency is kept.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Increase the value for the maximum physical address on SN systems.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
These are SN2 only drivers. They should have platform checks to prevent
them from doing evil stuff in GENERIC kernels.
Signed-off-by: Martin Hicks <mort@sgi.com>
Acked-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turn off the QLOGIC_FC driver. Supposedly qla2xxx should support
these devices. Do any ia64 machines have one of these devices as
the boot device?
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
New version leaves the original memory map unmodified.
Also saves any granule trimmings for use by the uncached
memory allocator.
Inspired by Khalid Aziz (various traces of his patch still
remain). Fixes to uncached_build_memmap() and sn2 testing
by Martin Hicks.
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch fixes a race condition where in system used to hang or sometime
crash within minutes when kprobes are inserted on ISR routine and a task
routine.
The fix has been stress tested on i386, ia64, pp64 and on x86_64. To
reproduce the problem insert kprobes on schedule() and do_IRQ() functions
and you should see hang or system crash.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch addresses a potential race condition for a case where Kprobe has
been removed right after another CPU has taken a break hit.
The way this is addressed here is when the CPU that has taken a break hit
does not find its corresponding kprobe, then we check to see if the
original instruction got replaced with other than break. If it got
replaced with other than break instruction, then we continue to execute
from the replaced instruction, else if we find that it is still a break,
then we let the kernel handle this, as this might be the break instruction
inserted by other than kprobe(may be kernel debugger).
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the ia64 architecture specific changes to prevent the
possible race conditions.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
64 bit architectures all implement their own compatibility sys_open(),
when in fact the difference is simply not forcing the O_LARGEFILE
flag. So use the a common function instead.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I've already sent this to the maintainers, and this is now being sent to a
larger community audience. I have fixed a problem with the ia64 version of
build_sched_domains(), but a similar fix still needs to be made to the
generic build_sched_domains() in kernel/sched.c.
The "dynamic sched domains" functionality has recently been merged into
2.6.13-rcN that sees the dynamic declaration of a cpu-exclusive (a.k.a.
"isolated") cpuset and rebuilds the CPU Scheduler sched domains and sched
groups to separate away the CPUs in this cpu-exclusive cpuset from the
remainder of the non-isolated CPUs. This allows the non-isolated CPUs to
completely ignore the isolated CPUs when doing load-balancing.
Unfortunately, build_sched_domains() expects that a sched domain will
include all the CPUs of each node in the domain, i.e., that no node will
belong in both an isolated cpuset and a non-isolated cpuset. Declaring a
cpuset that violates this presumption will produce flawed data structures
and will oops the kernel.
To trigger the problem (on a NUMA system with >1 CPUs per node):
cd /dev/cpuset
mkdir newcpuset
cd newcpuset
echo 0 >cpus
echo 0 >mems
echo 1 >cpu_exclusive
I have fixed this shortcoming for ia64 NUMA (with multiple CPUs per node).
A similar shortcoming exists in the generic build_sched_domains() (in
kernel/sched.c) for NUMA, and that needs to be fixed also. The fix
involves dynamically allocating sched_group_nodes[] and
sched_group_allnodes[] for each invocation of build_sched_domains(), rather
than using global arrays for these structures. Care must be taken to
remember kmalloc() addresses so that arch_destroy_sched_domains() can
properly kfree() the new dynamic structures.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When handling writes to /proc/irq, current code is re-programming rte
entries directly. This is not recommended and could potentially cause
chipset's to lockup, or cause missing interrupts.
CONFIG_IRQ_BALANCE does this correctly, where it re-programs only when the
interrupt is pending. The same needs to be done for /proc/irq handling as well.
Otherwise user space irq balancers are really not doing the right thing.
- Changed pending_irq_balance_cpumask to pending_irq_migrate_cpumask for
lack of a generic name.
- added move_irq out of IRQ_BALANCE, and added this same to X86_64
- Added new proc handler for write, so we can do deferred write at irq
handling time.
- Display of /proc/irq/XX/smp_affinity used to display CPU_MASKALL, instead
it now shows only active cpu masks, or exactly what was set.
- Provided a common move_irq implementation, instead of duplicating
when using generic irq framework.
Tested on i386/x86_64 and ia64 with CONFIG_PCI_MSI turned on and off.
Tested UP builds as well.
MSI testing: tbd: I have cards, need to look for a x-over cable, although I
did test an earlier version of this patch. Will test in a couple days.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Zwane Mwaikambo <zwane@holomorphy.com>
Grudgingly-acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resend using accessors instead of volatile qualifiers per hch comments, and
easier to understand convenience macros per rja comments.
Patch to apply volatile semantics when accessing MMR's in various SN files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The config option 'CONFIG_ACPI_DEALLOCATE_IRQ' is no longer
needed. This patch removes it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The reenabling of psr.ic should really belong to dtr mapping code block.
It make the fall through code fast since it doesn't need to execute the
predicated-off instruction. Logically make more sense as well since psr.ic
was turned off in .map code block.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The exception handler in copy user always expects fault occurs only on
user space address and the fall back recovery code is written with that
very assumption in mind. Recent source code inspection revealed that
while it worked splendid and to the expectation under normal circumstances,
It broke down under unexpected condition where some address calculation
might go outside the legal address range the original copy_user was
called for. This patch is to make copy_user exception handler more robust
and to prevent potential memory corruption.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When XPC is being shutdown (i.e., rmmod, reboot) it doesn't ensure that
other partitions with whom it was connected have completely disengaged
from any attempt at cross-partition memory references. This can lead to
MCAs in any of these other partitions when the partition is reset.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When copying data from user-space to kernel-space by __copy_user(),
a page_not_present fault sometimes occurs at vmalloced kernel address
because of VHPT pre-fetching.
Ignore the page_not_present fault in ia64_do_page_fault() before
jumping into exception handlers.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
1) workaround a h/w reset issue
2) to improve the determination of FPGA-based h/w in
the arch/ia64/sn/kernel/tiocx code.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change sn2-specific calls into generic functions. Without this change
the uncached allocator will not work on non-sn2 platforms.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
- notifying the PROM of specific features that are supported by the OS.
This is used to enable PROM feature if and only if the corresponding
feature is implemented in the OS
- fetch feature sets that are supported by the current PROM. This allows
the OS to selectively enable features when the PROM support is available.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
I've solved the problem I was having with the simulator and not
booting Debian.
The problem is that the number of bits for the virtual linear array
short-format VHPT (Virtually mapped linear page table, VMLPT for
short) is being tested incorrectly.
There are two problems:
1. The PAL call that should tell the kernel the size of the
virtual address space isn't implemented for the simulator, so
the kernel uses the default 50. This is addressed separately
in dc90e95f31
2. In arch/ia64/mm/init.c there's code to calcualte the size
of the VMLPT based on the number of implemented virtual address
bits and the page size. It checks to see if the VMLPT base
address overlaps the top of the mapped region, but this check
doesn't allow for the address space hole, and in fact will
never trigger.
Here's an alternative test and panic, that I think is more accurate.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not all of the PAL VM calls are implemented for the SKI simulator.
Don't just give up if one fails, print information from the calls
that succeed.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch implements PAL_VM_SUMMARY (and PAL_MEM_ATTRIB for good
measure) and pretends that the simulated machine is a McKinley.
Some extra comments and clean-up by Tony Luck.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
copy_page.o appeared twice in arch/ia64/lib/Makefile. The
one in global lib-y is wrong where it should be just in
lib-$(CONFIG_ITANIUM).
Both copy_page.o and copy_page_mck.o are build for Itanium2
processor and the link order will pick up the low performing
copy_page function (originally written for itanium processor).
In this case, we really want the copy_page_mck.o for optimized
version.
Signed-off-by: Kenneth Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch to support P-state transitions on ia64. This driver is based on ACPI,
and uses the ACPI processor driver interface to find out the P-state support
information for the processor. This driver plugs into generic cpufreq
infrastructure.
Once this driver is loaded successfully, ondemand/userspace governor can be
used to change the CPU frequency dynamically based on load or on request from
userspace process.
Refer :
ACPI specification -
http://www.acpi.info
P-state related PAL calls -
http://developer.intel.com/design/itanium/downloads/24869909.pdf
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
bte_copy() calls calls smp_processor_id(), which will get flagged if
preemption if enabled. raw_smp_processor_id() is used instead
because we are just using it to pick a BTE interface and are not
tied to a specific cpu.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract irq_affinity down to the pci provider level since
different SGI hardware implements this in different ways.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
Build issues were mostly in the ACPI=n case -- don't do that.
Select ACPI from IA64_GENERIC.
Add some missing dependencies on ACPI.
Mark BLACKLIST_YEAR and some laptop-only ACPI drivers
as X86-only. Let me know when you get an IA64 Laptop.
Signed-off-by: Len Brown <len.brown@intel.com>
Clean up of SGI SN partitioning related code.
The SN_SAL_GET_SN_INFO SAL call returns the partition ID, making
the SN_SAL_SYSCTL_PARTITION_GET SAL call redundant. Remove sn_partid
and use sn_partition_id.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the SN pci device info to use the nearest node function
to allocate driver memory on the nearest node (rather than
defaulting to node 0).
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Add a new exported function for determining the nearest node
with CPUs for I/O nodes and fix a bug where the hwperf dynamic
misc device was being registered before misc_init().
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Bugfix to export PCI topology information in /proc/sgi_sn/sn_topology.
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, region numbers are defined in several files, with several
names. For example, we have REGION_KERNEL in asm/page.h and
RGN_KERNEL in pgtable.h
We also have address definitions that should depend on the
RGN_XXX macros, but are currently just long constants.
The following patch reorganises all the definitions so that they have
the same form (RGN_XXX), are in one place, and that addresses that
depend on RGN_XXX are derived from them.
(This is a necessary but not sufficient patch to allow UML-like
operation on IA64).
Thanks to David Mosberger for catching the change I missed in mmu_context.h.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Kernel 2.6 doesn't support egcs, and I didn't find any user of this
function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Removed IA64 architecture specific users of asm/segment.h
The removal of asm-ia64/segment.h itself can wait until all
of the kernel source has been purged of references.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_bus_to_resource is exported on all architectures except ia64
and sparc. Add exports for the two missing architectures. Needed when
Yenta socket support is compiled as a module.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Thanks to Stephane, we've now worked out the real cause of the
`Linux will not boot on simulator' problem. Turns out it's a stack
overflow because the stack pointer wasn't being initialised properly
in boot_head.S (it was being initialised to the lowest instead of the
highest address of the stack, so the first push started to overwrite
data in the BSS).
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix swiotlb sizing to match what the comments and the kernel
parameters documentation indicate. Given a default 16k page size kernel
(ia64) and a 2k swiotlb page size, we're off by a multiple of 8 trying
to size the swiotlb. When specified on the boot line, the swiotlb is
made 8x bigger than requested. When left to the default value, it's 8x
smaller than the comments indicate. For x86_64 the multiplier would be
2x. The patch below fixes this. Now, what's a good default swiotlb
size? Apparently we don't really need 64MB.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After building a fresh tree with gcc 4 I can't boot the simulator as
the bootloader loader dies with
loading /home/ianw/kerntest/kerncomp//build/sim_defconfig/vmlinux...
failed to read phdr
After some investigation I believe this is do with differences between
the alignment of variables on the stack between gcc 3 and 4 and the
ski simulator. If you trace through with the simulator you can see
that the disk_stat structure value returned from the SSC_WAIT_COMPLETION
call seems to be only half loaded. I guess it doesn't like the alignment
of the input.
Signed-off-by: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Shub2 provides a much improved mechanism for issuing internode
TLB purges. Add code to support the newer mechanism. There is also
some debug code (disabled) that is useful for testing.
Collect statistics on the number, type & duration of TLB purges.
This data will be useful for making future improvements in the algorithms.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Change the BTE driver so that it works for both shub1 and
shub2. Most of the changes are related to the number of cores
that use the BTE engine, to the MMR addresses of various
shub registers, and to using the correct processor or network
physical address.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Disable some shub1-specific code when running on systems with shub2.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the addresses of the pio_write_status_addr so that
they are correct for newer processors. Shub2 did not number
the threads in the order that I had expected.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use local SHUB alias space when referencing MMRs that are known
to be node local. There is a slight performance benefit & code
simplification.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Just `make oldconfig' doesn't help for the zx1 defconfig ---
because we need the MPT Fusion drivers, which are picked up as not
selected.
Tested on HP ZX2000 and ZX2600.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The main issue is that bus_fixup calls may potentially call
functions that require a valid bus->sysdata pointer. Since
this is the case, we must set the bus->sysdata pointer before
calling the bus_fixup functions. The remaining changes are
simple fixes to make sure memory is cleaned up in the function.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The current one doesn't even make sense anymore on i386 where it
apparently came from.
Follow-up wordsmithing by Matthew Wilcox and Tony Luck.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to add an SN pci provider for TIOCE, which is SGI's
PCI Express implementation.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to add TIO "huge-window" address support to sn_dma_flush().
Update copyright in affected files.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Altix patch to abstract the force_interrupt() mechanism away from the
pcibr provider.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cosmetic altix patch to rename SGI_PCIBR_ERROR to something more generic and
remove a duplicate #define.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The PFM_LOAD_CONTEXT may fail silently and cause a session
to remain reserved even though it should not. This can happen
when the commands succeeds in reserving the session but fails
when it actually tries to attach to the load_pid. In that case,
the command has failed but will return 0. More importantly,
the session will remain reserved. This patch fixes the problem.
Signed-off-by: <stephane.eranian@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
this changeset broke the "nohalt" kernel boot option.
8df5a500a3
default_idle() is looking at new variable can_do_pal_halt. However,
that variable did not get cleared upon "nohalt" boot option. Result
is that "nohalt" option is ignored until perfmon is exercised.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
