Cosmetic patch removing an empty line at the end of the NB pinctrl node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Ports interrupts are used by the PPv2 driver when no PHY is connected to
a port. This patch adds a description of these interrupts.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch describes the comphy available in the cp110 master and slave.
This comphy provides serdes lanes used by various controllers such as
the network one.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch extends on both cp110 the system register area length to
include some of the comphy registers as well.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
There is a further gate in between the mipidphy reference clock and the
actual ref-clock input to the dsi host, making the clock hirarchy look like
clk_24m --> Gate11[14] --> clk_mipidphy_ref --> Gate21[0] --> clk_dphy_pll
Fix the clock reference so that the whole clock subtree gets enabled when
the dsi host needs it.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[amended commit message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Extend the container size to 0x2000 to include the gpio controller at
offset 0x1040.
While at it, add start address notation to the gpio node name to match
its 'offset' property.
Fixes: 63dac0f492 ("arm64: dts: marvell: add gpio support for Armada
7K/8K")
Cc: <stable@vger.kernel.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By adding this regulator, a proper reset is done during boot. Without
this, the UHS failed to be detected after a warm reboot when the SD card
remained in the slot, then it fallback to an HS.
Note that the vmcc is supported by the xenon driver only with the
following fix: "mmc: sdhci-xenon: add set_power callback".
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The downstream RTD1195 and apparently RTD1295 trees have a modified 8250
serial driver that acknowledges its interrupts using the second reg area,
which is an irq mux.
Drop these unused second reg entries for the UART nodes.
Fixes: 72a7786c0a ("ARM64: dts: Add Realtek RTD1295 and Zidoo X9S")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Define the generic R8A77970 part of the EtherAVB device node.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF ports in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC1/2 in the R8A77970 device tree.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A77970 SoC device tree including Cortex-A53 CPU, GIC, timer,
CPG, RST, and SYSC.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded clock indices by R8A77995_CLK_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded power domain indices by R8A77995_PD_* symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Node names should not use numerical suffixes if the nodes can be
distinguished by unit-address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU is already wired up to the HDMI encoder, all we need to do is
enable it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch changes the name from from e6060000.pfc and pfc@e6060000 to
e6060000.pin-controller and pin-controller@e6060000 like other Renesas
SoCs.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7796 has a single FDP1 instance.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The A64 SPI controllers are register compatible to the h3/h5 SPI
controllers.
The A64 has two SPI controllers, each with a single chip select.
The handles for the DMA channels (23/24 for SPI0/SPI1) are omitted,
as the A64 DMA support is currently missing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators, replace
fixed regulator with AXP803 dcdc1 regulator.
Tested on pine64.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the graphics-related nodes on the rk3399-firefly which makes
it possible to see output on the on-board hdmi output.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3328 Evaluation Board use rk805 pmic, and one of the DCDCs in
rk805 is for cpu regulator, assign the cpu regulator, so the
cpufreq can work fine.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This reverts commit 6f2dea1f5f.
Without accurate cpu regulators being set for boards this will wreak havoc
when cpufreq-dt begins to set new frequencies without adjusting the core
frequency.
Additionally the rk3368 has an unsolved issue in that it has two separate
cpu clusters with separate clock lines but only one cpu supply regulator
for both clusters, which causes even more problems.
While it seems that originally only one cluster was supposed to be active
at a time (big or little), talking with real users of the hardware
revealed that having all 8 cores accessible at 1.2GHz max is way more
liked than having 4 cores at 1.5GHz max. Such an approach needs changes
to cpufreq and/or opp though to control the two separate clock lines when
setting both clusters to the same frequencies.
In any case, having the OPPs in the dts at this point in time is
undesireable, so remove them again for now.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZsr8cAAoJEFmIoMA60/r8lXYQAKViYIRMJDD4n3NhjMeLOsnJ
vwaBmWlLRjSFIEpag5kMjS1RJE17qAvmkBZnDvSNZ6cT28INkkZnVM2IW96WECVq
64MIvDijVPcvqGuWePCfWdDiSXApiDWwJuw55BOhmvV996wGy0gYgzpPY+1g0Knh
XzH9IOzDL79hZleLfsxX0MLV6FGBVtOsr0jvQ04k4IgEMIxEDTlbw85rnrvzQUtc
0Vj2koaxWIESZsq7G/wiZb2n6ekaFdXO/VlVvvhmTSDLCBaJ63Hb/gfOhwMuVkS6
B3cVprNrCT0dSzWmU4ZXf+wpOyDpBexlemW/OR/6CQUkC6AUS6kQ5si1X44dbGmJ
nBPh414tdlm/6V4h/A3UFPOajSGa/ZWZ/uQZPfvKs1R6WfjUerWVBfUpAzPbgjam
c/mhJ19HYT1J7vFBfhekBMeY2Px3JgSJ9rNsrFl48ynAALaX5GEwdpo4aqBfscKz
4/f9fU4ysumopvCEuKD2SsJvsPKd5gMQGGtvAhXM1TxvAoQ5V4cc99qEetAPXXPf
h2EqWm4ph7YP4a+n/OZBjzluHCmZJn1CntH5+//6wpUk6HnmzsftGELuO9n12cLE
GGkreI3T9ctV1eOkzVVa0l0QTE1X/VLyEyKCtb9obXsDaG4Ud7uKQoZgB19DwyTJ
EG76ridTolUFVV+wzJD9
=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
SDR104 seems to be OK on the nanopi-k2 SBC so enable it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable UHS modes, up to SDR50, on the nanopi-k2 SBC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable sdcard UHS modes, up to SDR50, on p20x based boards.
While the s905 supports SDR104 mode, it appears that the PCB of p20x
based boards can't cope with a rate as high as 200Mhz.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable sdcard UHS modes up to SDR50. Unfortunately, it seems the PCB of
the libretech-cc cannot handle SDR104 at 200Mhz reliably.
Also enable eMMC DDR52 mode.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the cc is not instantaneous, especially
when switching from 3.3v to 1.8v.
It take at least 30ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 61ff2af9b278 ("ARM64: dts: fixup libretech cc definition")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Changing the card voltage on the nanopi-k2 is not instantaneous,
especially when switching from 3.3v to 1.8v.
It take at least 3ms for the regulator to go from 3.3v to 1.8v. Add
margin to that to make sure we don't upset the sdcard during the voltage
switch
Fixes: 9bc7ffb08d ("arm64: dts: amlogic: Add NanoPi K2")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This
is necessary to be able to gate the clk outside of the SoC while
keeping it running in the controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It does not make much sense to define cap-sd-highspeed in the emmc nodes
Just remove it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now that the clock source 0 is properly described in the CCF, use it
instead of assuming the default value (xtal)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull irq updates from Thomas Gleixner:
"The interrupt subsystem delivers this time:
- Refactoring of the GIC-V3 driver to prepare for the GIC-V4 support
- Initial GIC-V4 support
- Consolidation of the FSL MSI support
- Utilize the effective affinity interface in various ARM irqchip
drivers
- Yet another interrupt chip driver (UniPhier AIDET)
- Bulk conversion of the irq chip driver to use %pOF
- The usual small fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
irqchip/ls-scfg-msi: Add MSI affinity support
irqchip/ls-scfg-msi: Add LS1043a v1.1 MSI support
irqchip/ls-scfg-msi: Add LS1046a MSI support
arm64: dts: ls1046a: Add MSI dts node
arm64: dts: ls1043a: Share all MSIs
arm: dts: ls1021a: Share all MSIs
arm64: dts: ls1043a: Fix typo of MSI compatible string
arm: dts: ls1021a: Fix typo of MSI compatible string
irqchip/ls-scfg-msi: Fix typo of MSI compatible strings
irqchip/irq-bcm7120-l2: Use correct I/O accessors for irq_fwd_mask
irqchip/mmp: Make mmp_intc_conf const
irqchip/gic: Make irq_chip const
irqchip/gic-v3: Advertise GICv4 support to KVM
irqchip/gic-v4: Enable low-level GICv4 operations
irqchip/gic-v4: Add some basic documentation
irqchip/gic-v4: Add VLPI configuration interface
irqchip/gic-v4: Add VPE command interface
irqchip/gic-v4: Add per-VM VPE domain creation
irqchip/gic-v3-its: Set implementation defined bit to enable VLPIs
irqchip/gic-v3-its: Allow doorbell interrupts to be injected/cleared
...
-----BEGIN PGP SIGNATURE-----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=5fxW
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
Adding more resources on the network controller ppv2.2 on Armada 7K/8K
allowing to use last improvement introduced in the driver.
Also enabling more network ports on the mcbin (A8K base board)
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWaaJiiMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71QonAJ9HyQXhNQBN
BK1PYsmmDqVfNHBesACcCVEof+kHPYIwqLi+lzt2hEGMPmQ=
=ty8P
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-4' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 4)
Adding more resources on the network controller ppv2.2 on Armada 7K/8K
allowing to use last improvement introduced in the driver.
Also enabling more network ports on the mcbin (A8K base board)
* tag 'mvebu-dt64-4.14-4' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix number of GPIOs in AP806 description for Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWal5XSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71W2pAJ90lo/XfZ3O
y7YizLM864H+4XGl9gCeOfmhngOW/lj1gPAVny35hw/ua00=
=2qOU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.13 (part 3)
Fix number of GPIOs in AP806 description for Armada 7K/8K
* tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes "msi-parent" to refer to all
MSI controller dts nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
"1" should be replaced by "l". This is a typo.
The patch is to fix it.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The network driver on Marvell SoC (7k/8k) needs to access some registers
in the system controller to configure its ports at runtime. This patch
adds a phandle reference to the syscon system controller node in the
ppv2 node.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit updates the Marvell Armada 7K/8K Device Tree to describe
the TX interrupts of the Ethernet controllers, in both the master and
slave CP110s.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Add description for a new family SoC from Marvell: Armada-8KP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmeipsACgkQCwYYjhRyO9UnEACcDuFAUJNT2eth5lYMHoHcvMLf
x7QAnjqghjBpm7nYOutsYPY5gwz/YYC6
=+kES
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 3)
Add description for a new family SoC from Marvell: Armada-8KP.
* tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Device Tree files for Armada-8KP
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert all RK3399 platforms to use per-lane PHY model in order to save
more power by idling unused lane(s).
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds reset controller node of analog signal amplifier
core (ADAMV) for UniPhier LD11/LD20 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdnagQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSpBB/9v6flM/QtBVeXhR1tfrXIt3veUaiwiTwhg
PIj6J7EJZCgA9TiHr4zcQzjCx581a9v1rUEpnhZyi7d/zrNurpJRYtBNcqfDS28Z
kyL30gwf/y4nVAzgIODGMNRWe3+IETNCIRZ236cV7jr9HgKmHvA0qc2aMzjHPMCF
XS9wPXgEW1kYIgKqzq1drAWY3iVB0W37KMX9HKVQfAlPcGu5jobk0lruQBZV0InH
8NR3NB9a7eknzPejmBO2ga0idS0oAc/eFQ8h2bHrxWVm1JO+2QDc7epxWCTmxBcP
DLy+7tuQiXEFc25AM3QpW97pJuqDT+zeZXd/F5BK5uGnpH63SNbi
=D65g
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "second round of Rockchip dts64 changes for 4.14" from Heiko Stübner:
3 new boards, the rk3328-based Rock64 from the Pine64-makers, the
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
* tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
arm64: dts: rockchip: add rk3328-rock64 board
arm64: dts: rockchip: add rk3328 pdm node
arm64: dts: rockchip: add more rk3399 iommu nodes
arm64: dts: rockchip: add rk3368 iommu nodes
arm64: dts: rockchip: add rk3328 iommu nodes
arm64: dts: rockchip: Add basic cpu frequencies for RK3368
arm64: dts: rockchip: add rk805 node for rk3328-evb
arm64: dts: rockchip: Assign mic irq to correct device for Gru
arm64: dts: rockchip: init rk3399 vop clock rates
arm64: dts: rockchip: Add pwm nodes for rk3328
arm64: dts: rockchip: Fix wrong rt5514 dmic delay property for Gru
arm64: dts: rockchip: disable tx ipgap linecheck for rk3399 dwc3
arm64: dts: rockchip: remove num-slots property from rk3399-sapphire
arm64: dts: rockchip: Enable tsadc module on RK3328 eavluation board
arm64: dts: rockchip: add thermal nodes for rk3328 SoC
arm64: dts: rockchip: add tsadc node for rk3328 SoC
arm64: dts: rockchip: add rk3328 i2s nodes
...
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Haikou is a Qseven and μQseven baseboard featuring PCIe, USB3 and a
video connector for MIPI-DSI/CSI and eDP adapter.
This dts is for usage with the RK3399-Q7 SoM Puma.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch describes the GPIO lines usage on the LibreTech CC board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whiespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The AO clkc needs to be updated to new bindings with an system control parent
node and moving the clkc node as subnode.
Also adds the SoC specific compatible following the bindings requirements.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This enables option to use dt binding
headers.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable smmu via dtsi. Enable it in board file when needed.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline kernel has r1p12 compatible string now. Use this new compatible
string and also append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Adding prefetchable memory space to pcie device tree node.
Shifting configuration space to 64-bit address space.
Removing pcie device tree node from amba as it requires size-cells=<2>
in order to access 64-bit address space.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add debug console to dtsi to be able to enable it in
board dts file.
Keep in your mind that every core has separate dcc port in case you want
to run SMP kernel.
DCC is very helpful communication channel for debugging.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the idle-states node to describe zynqmp idle states. Only
cpu-sleep-0 idle state is added in this patch. References to the
idle-states node are added in all CPU nodes. Time values: entry/exit
latencies and min-residency, needs to be tuned. arm,psci-suspend-param
is selected to comply with PSCIv1.0 and Extended StateID format.
Signed-off-by: Stefan Krsmanovic <stefan.krsmanovic@aggios.com>
Acked-by: Will Wong <willw@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
-----BEGIN PGP SIGNATURE-----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=u/18
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 device tree changes for 4.14, round 2" from Chen-Yu Tsai:
The usual improvement patches:
- PMIC, USB and WiFi enabled for Bananapi M64
- New board added: NanoPi A64
- New board added: Olimex A64-OLinuXino
* tag 'sunxi-dt64-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: Add A64-OLinuXino initial support
arm64: allwinner: a64: Add initial NanoPi A64 support
arm64: allwinner: a64: add proper support for the Wi-Fi on BPi M64
arm64: allwinner: a64: enable AXP803 for Banana Pi M64
arm64: allwinner: a64: enable USB host controller for BPi M64
Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".
Fixes: 48f4d9796d (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Enable uSD on ESPRESSObin (Armada 37xx based board)
- Add NAND support on Armada 7K/8K SoCs
- Enable USB host on Armada-7040-DB and Armada-8040-DB boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmWtIYACgkQCwYYjhRyO9V67ACfUFPrkPl8Qn34OAjklU+hVPR9
YJIAn0EI8S47gAuQe0bzEmU45qALL/Xv
=Vf0A
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-2' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt64 for 4.14 (part 2)" from Gregory CLEMENT:
- Enable uSD on ESPRESSObin (Armada 37xx based board)
- Add NAND support on Armada 7K/8K SoCs
- Enable USB host on Armada-7040-DB and Armada-8040-DB boards
* tag 'mvebu-dt64-4.14-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: enable USB host on Armada-8040-DB
ARM64: dts: marvell: enable USB host on Armada-7040-DB
ARM64: dts: marvell: add NAND support on the CP110
ARM64: dts: marvell: armada-37xx: Enable uSD on ESPRESSObin
arm64: dts: marvell: Fully re-order nodes in Marvell CP110 dtsi files
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6XqO
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Second Round of Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add PFC device node to R-Car D3 (r8a77995)
This is a step towards enabling devices that use multiplexed pins
- including ethernet - on boards that use the r8a7796 SoC.
* Add USB nodes to R-Car M3-W (r8a7796)
This is a step towards enabling USB devices on boards that
use the r8a7796 SoC.
* Use newly added Gen-3 fallback compat string
This is consistent with ongoing efforts to use per-generation
fallback strings where appropriate across devices found
on R-Car SoCs. The aim of the effort being to strike a balance
between the limited information available about the compatibility
of devices found on different SoCs and the desire to ease enabling
devices on new SoCs.
This has no run-time effect due to the presence of a per-SoC
compat string.
* Cleanup whitespace and extra LVDS port label
Minor cleanups, no run-time effect.
* tag 'renesas-arm64-dt2-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a77995: add pfc device node
arm64: dts: r8a7796: Add HSUSB device node
arm64: dts: r8a7796: Add USB-DMAC device nodes
arm64: dts: r8a7796: Add USB3.0 host device node
arm64: dts: r8a7796: add USB2.0 Host (EHCI/OHCI) device nodes
arm64: dts: r8a7796: add usb2_phy device nodes
arm64: dts: r8a7795: correct whitespace of companion property
arm64: dts: r8a7795: Use R-Car SATA Gen3 fallback compat string
arm64: dts: salvator-common: Remove extra LVDS port label
* Add IPQ8074 SoC and HK01 board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JCl4
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Pull "Qualcomm ARM64 Updates for v4.14 Part 2" from Andy Gross:
* Add IPQ8074 SoC and HK01 board support
* tag 'qcom-arm64-for-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: Add ipq8074 SoC and HK01 board support
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
-----BEGIN PGP SIGNATURE-----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=WUr3
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Pull "Broadcom devicetree changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes for
4.14, please pull the following:
- Eric moves the bcm2837 DT file from arm64 to arm because it created a maintenance
problem and would have required either duplication or cross merges
- Stefan changes how the pinmuxing is defined and pushes it at the board level
to support Raspberry Pi Zero Wireless. He then adds supports for the actual
Raspberry Pi Zero Wireless board along with binding documentation. Stefan
also defines a proper SMP enable-method property and binding for BCM2836
(Raspbery Pi 2)
- Rafal describes the BCM5301X USB ports correctly in Device Tree such that
it becomes possible to assign them to specific LED triggers (e.g: USB activity).
He does the same thing for BCM53573 and defines default LED triggers for USB.
- Jon provides a fix for Northstar Plus which consists in correctly defining
the "dma-coherent" property for peripherals which are DMA coherent. He also
does a bit of re-arrangement of the USB DT nodes and finally adds USB 3 PHY
and host controller support for NorthStar Plus
- Florian adds support for Broadcom's BCM947189ACDBMR reference board which is
based on BCM47182/53573 and which supports external MoCA (BCM6802)
- Ray fixes the wrong UART2 base address for Cygnus
- Scott moves the v3d node in the proper unit address order and defines the correct
UART alias for the BCM91130_entphn reference board to be UART3
- Jason adds the DT node for the Cygnus Cortex-A9 Performance Monitoring Unit
- Jonathan adds a bunch of additional peripherals to the Cygnus DTS include file:
SDHCI, Keypad, SPI, DMA and pinmux configurations
- Raveendra adds the Cygnus OHCI and EHCI Device Tree nodes
* tag 'arm-soc/for-4.14/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM53573: Specify ports for USB LED for Tenda AC9
ARM: dts: cygnus: Add generic-ehci/ohci nodes
ARM: dts: cygnus: add serial0 alias for uart3 on bcm91130_entphn
ARM: dts: cygnus: Add additional peripherals to dtsi
ARM: dts: cygnus: Enable Performance Monitoring Unit
ARM: dts: cygnus: place v3d in proper address ordered location
ARM: dts: cygnus: Fix incorrect UART2 register base
ARM: dts: bcm283x: Add 32-bit enable method for SMP
dt-bindings: arm: add SMP enable-method for BCM2836
ARM: dts: BCM53573: Add Broadcom BCM947189ACDBMR board support
ARM: dts: BCM5301X: Specify USB ports for USB LEDs of few devices
ARM: dts: NSP: Add USB3 and USB3 PHY to NSP
ARM: dts: NSP: Rearrage USB entries
ARM: dts: NSP: Add dma-coherent to relevant DT entries
ARM: dts: bcm2835: Add Raspberry Pi Zero W
dt-bindings: bcm: Add Raspberry Pi Zero W
ARM: bcm283x: Define UART pinmuxing on board level
ARM: dts: BCM5301X: Specify USB ports for each controller
ARM: dts: bcm283x: Move the BCM2837 DT contents from arm64 to arm.
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots' from ZX296718 device tree.
- Enable various devices for ZX296718 SoC support, VGA display, I2S
audio, pinctrl, GPIO, PWM and IRDEC.
- Update zx296718-evb support to use audio-graph-card for HDMI audio
and add I2S sound card.
- Add initial zx296718-pcbox board support with storage, audio,
display devices enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZlo4KAAoJEFBXWFqHsHzOee0H/RcMMznh0cKg8UjjlbAuhArW
4IxmA05TzYBN0VeLNwAzPMn3yrbSZPk5bm7MD/+csv6NuFF2NDlvshyAqWAYueaY
cLXnQvqE3axK5X9xkfQYKvk0OHhj/xIKzEdnJ3++EwEtnibUEl9g8kunopzTQOaq
BsOFTTfuey98hCg4WQSpGIqRhfpKXt/UV63e93TuPs1g0/fpmoooMTQdUE+Wmctq
y1JJb3OC5HMp/NkQRJobmUa2r6R+3T8gmvgFopoBVP543zR5kwJ7bCDXgkzZwIbV
jtLDVCfg+DAapSFpCbULkvOMMZo/rxjAFxP2b8ICFCzNC9zgWpoSAN8ut1Oznk0=
=hAsg
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree updates for 4.14" from Shawn Guo:
- A clean up patch from Shawn Lin to remove the deprecated dwmmc
property 'num-slots' from ZX296718 device tree.
- Enable various devices for ZX296718 SoC support, VGA display, I2S
audio, pinctrl, GPIO, PWM and IRDEC.
- Update zx296718-evb support to use audio-graph-card for HDMI audio
and add I2S sound card.
- Add initial zx296718-pcbox board support with storage, audio,
display devices enabled.
* tag 'zte-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zte: add initial zx296718-pcbox board support
arm64: dts: zx296718-evb: add I2S sound card support
arm64: dts: zx296718-evb: use audio-graph-card for HDMI audio
arm64: dts: zx296718: add irdec device for remote control
arm64: dts: zx296718: add PWM device support
arm64: dts: zx296718: add voltage data into OPP table
arm64: dts: zx296718: set a better parent clock for I2S0
arm64: dts: zx296718: add pinctrl and gpio devices
arm64: dts: zx296718: add I2S and I2C audio codec
arm64: dts: zx296718: add VGA device support
arm64: dts: zte: remove num-slots from zx296718
- Correct the typo in fsl-ls1088a-rdb board name.
- A series from Horia Geantă to consolidate aliases node and enable
crypto support for ls208xa and ls1088a.
- Enable USB host support for ls1012a.
- Enable cpuidle support for ls1088a and ls208xa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZlodKAAoJEFBXWFqHsHzOLYAIAIs6YEEhjbJiet6EMmwpneJo
hTGcU/Gv6q6ozF3uV1+oMqnv64rlzwPR8jTjt29+lCS2I4/zv7Zfr83GR1iMtW90
hIKUMnWwX/ATY1BC4YB36E0Z0WRolNoKU6iKBujMsfxPFRBXulEQwngZoFS5EvHy
TDqCTTRHBHhnzPqMPSJ3q/3r6VPTHDtj1ap+zF8EsS156ybPHhajHm/+u3Kvh6Kh
MnI+Y/SHPFCmy2Pj34SsixGKBEwAukyeddbufUlnrP3wcDnIvv64SWURCsBygEww
jhAD8rYWCFyhqM4vBbQ8AvXrKJkJDZETRy1GTTwDK2MjWeIzY6JtZ+cOGtyBTwU=
=6GLX
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "Freescale arm64 device tree updates for 4.14" from Shawn Guo:
- Correct the typo in fsl-ls1088a-rdb board name.
- A series from Horia Geantă to consolidate aliases node and enable
crypto support for ls208xa and ls1088a.
- Enable USB host support for ls1012a.
- Enable cpuidle support for ls1088a and ls208xa.
* tag 'imx-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls1088: Correction in Board name from "L1088A" to "LS1088A"
arm64: dts: ls208xa: add cpu idle support
arm64: dts: ls1088a: add cpu idle support
arm64: dts: freescale: ls1088a: add crypto node
arm64: dts: freescale: ls208xa: add crypto node
arm64: dts: freescale: ls208xa: share aliases node
arm64: dts: ls1012a: add USB host controller nodes
4.14, please pull the following:
- Scott moves all the Northstar 2 DTS files into a sub-directory to be consistent
with what was done for stingray and to future proof the addition of new board
DTS files
- Velibor adds the ARM CCN-502 interconnect DT node to the Stingray SoC
DTS include file
- Srinath adds the MDIO multiplexer and SATA nodes to the Stingray DTS
include files
- Anup adds the SP804 timers, FlexRM (mailbox) and RAID engine DT nodes
to the Stingray DTS include files
- Abishek adds the BGMAC (Ethernet controller) node to the Stingray DTS
files
-----BEGIN PGP SIGNATURE-----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=0wLC
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.14/devicetree-arm64' of http://github.com/Broadcom/stblinux into next/dt64
Pull "Broadcom devicetree-arm64 changes for 4.14" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree changes for
4.14, please pull the following:
- Scott moves all the Northstar 2 DTS files into a sub-directory to be consistent
with what was done for stingray and to future proof the addition of new board
DTS files
- Velibor adds the ARM CCN-502 interconnect DT node to the Stingray SoC
DTS include file
- Srinath adds the MDIO multiplexer and SATA nodes to the Stingray DTS
include files
- Anup adds the SP804 timers, FlexRM (mailbox) and RAID engine DT nodes
to the Stingray DTS include files
- Abishek adds the BGMAC (Ethernet controller) node to the Stingray DTS
files
* tag 'arm-soc/for-4.14/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: Add SBA-RAID DT nodes for Stingray SoC
arm64: dts: Add FlexRM DT nodes for Stingray
arm64: dts: Add SATA DT nodes for Stingray SoC
arm64: dts: Add DT node to enable BGMAC driver on Stingray
arm64: dts: Add sp804 DT nodes for Stingray SoC
arm64: dts: Add MDIO multiplexer DT node for Stingray
arm64: dts: Enable stats for CCN-502 interconnect on Stingray
arm64: dts: move ns2 into northstar2 directory
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEE2nN1m/hhnkhOWjtHOJpUIZwPJDAFAlmWY8IOHHdlbnNAY3Np
ZS5vcmcACgkQOJpUIZwPJDCarBAA5ZLXl9Zp/JugO0JNuCyJpY3Z418hMMieqJ/P
k2iTdnxSZ3ZhZGqDy/yJtEVS4T1jEe3r+VumUqQI81u6LTKcSCTgngBp0X4pDjKP
VrPuvJZnaIQXGyxD+WRjeEZ9LwfU1KKwmkNF8ASnx53OyXF/qghl1OcCjV9nTfh8
HcMBuSK/qqEQ1LoF2gyM1XXHkSD1jSoA/Nzwxgp8ivSlRGzuwbHO0fv42eQfgI7h
D1Ufz3bAHh58YcarHMp53+6mMcaYNyTYwAzMH6/IAxwQ6CSSN6ZOsoe17+agEmoX
65pQJWeVx+i4n8WtGPX0uWcz9K/jKyXEdpCLY85ZYHZKTabb6ZTuhMkYyOvXzhMD
EvSas/dB6nhForHSPHVRYsS9zlwpwO5+LSAufYET0u/ec9RYL3S1f7JHNzYuLvgJ
/W5EEu063XyrTEF5/xEv7FEd30J2k9418dCPyjXknuDdXbq1/TFAX/fwW+9I/I6W
oguQbbuO7Op/LClVk15nPLIsdLwv2+QMbuWoqfqtK767x+cEpSYT2KY+s2OUjL8Y
m7baoPpbAFPWq34ZtWCQzXH3pQ1ghgvnDRVfsskCpNpC3uB0C7Y+/lexRHd2A1j4
ADf4k3jg2ybFUqADwHnCg7A+/wKCMDgIPLAfWgumgefUnZT0+YT7bP3xINks6/wi
eguEAXA=
=lSDD
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.13, round 2" from Chen-Yu Tsai:
Three fixes adding a missing alias for the Ethernet controller on A64
boards. One adding a missing interrupt for the pin controller.
* tag 'sunxi-fixes-for-4.13-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.
This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After adding the clock subsystem to the SOC, the dummy
clock clk32k is not longer needed. Delete it.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Use newly added R-Car SATA Gen3 fallback compat string
in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before the fallback compat string is considered.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The DU LVDS output is on port 3 on R8A7795 but on port 2 on R8A7796. The
lvds_connector label thus can't be defined in salvator-common.dtsi,
common to the two SoCs.
The lvds_connector label is meant for convenience to be referenced from
panel device tree files, such as r8a77xx-aa104xd12-panel.dtsi or
r8a77xx-aa121td01-panel.dtsi. As those files are not included in any
device tree source, and the label never used elsewhere, we can simply
remove it. Out-of-tree patches that include panel device tree files can
then add a
#define lvds_connector du_out_lvds0
before including the panel device tree file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZlVkYAAoJENfPZGlqN0++JKsP/i0hKyjgmvL983609fRwWcq9
i3nkGw+kxcv0ZBLSjWR++mPsQ3PPTgOk1MpJL3ioL8WZBuaTghCpsGrsVRnNViq8
RlDhShNPlvqcq9MOoAcc6rgqxron7P97Eykt1IXIDqgPlRNRRlSjil0MovLonzDW
S2T1W6gRjKKSOdPpZbXhxDeBwv2lEr7+688kU9ZTvzKN4KWdsShuuVSnW786wWgM
SJ8ZFzI5RzUsqcqvpeEWpe+z5eZo/GFDtmQ3E/ngCzrwbAwbVUeEXjvLLJF9oHSs
sMU66eOoU7erRqTe6KjpW+qIIRkaAR3rH5vVQB0tCJVl4kORWTVFcUGWiQ3ON3cP
wPrObeBCzzKamWoH6QJ7oWFvFYOVFOQtm3PaXBuSkWjlldLA9FdhLZJ1mYdrk5i6
PnIdvJGXRC0nH/+yJkbheG8FRNhz92eCG1u3gUBEGVKMwYDBWlztYVAI32MypKcm
+2xnR1Fs2uMzD/WxsM/PHaeU2LeTt/pnazgUInwnjDEFUR6fRP1MpkoFcspRk3Ix
QqF7HmLmn7ezho+Z+PXFYKPJvLHwTyHRI8TQtFzarFWXm+Y/ve5GVdbDLVkw31Aa
jy/w10dGmh9Q3z3sD2jhQKYuNVE0fhsZC1xkVCIodtYpyULfcLJvGJuUazlqpFZz
z3hXHslR7p1se40FdP6k
=meey
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Fourth Round of Renesas ARM Based SoC Fixes for v4.13" from Simon Horman:
* Avoid audio_clkout naming conflict for salvator boards using
Renesas R-Car Gen 3 SoCs
Morimoto-san says "The clock name of "audio_clkout" is used by the
Renesas sound driver. This duplicated naming breaks its clock
registering/unregistering. Especially when unbind/bind it can't handle
clkout correctly. This patch renames "audio_clkout" to "audio-clkout" to
avoid the naming conflict."
* tag 'renesas-fixes4-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: renesas: salvator-common: avoid audio_clkout naming conflict
1. Replaces old coresight ATB programmable replicator compatible with
new and more generic one
2. Replaces incorrect usage of underscores for device node names in the
device tree with hyphen
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jaSe
-----END PGP SIGNATURE-----
Merge tag 'juno-updates-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt64
Pull "ARMv8 Vexpress/Juno DT updates for v4.14" from Sudeep Holla:
1. Replaces old coresight ATB programmable replicator compatible with
new and more generic one
2. Replaces incorrect usage of underscores for device node names in the
device tree with hyphen
* tag 'juno-updates-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: replace underscores with hyphen in device node names
arm64: dts: juno: Use the new coresight replicator string
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
-----BEGIN PGP SIGNATURE-----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=9oen
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Pull "Allwinner arm64 DT changes for 4.14" from Chen-Yu Tsai:
The usual improvement patches:
- R_INTC interrupt controller enabled for the A64 SoC
- AXP803 PMIC added and enabled on the Pine64 and SoPine boards
* tag 'sunxi-dt64-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: a64: add AXP803 PMIC support to SoPine and the baseboard
arm64: allwinner: a64: enable AXP803 regulators for Pine64
arm64: allwinner: a64: add DTSI file for AXP803 PMIC
arm64: allwinner: a64: add AXP803 node to Pine64 device tree
arm64: allwinner: a64: add NMI (R_INTC) controller on A64
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmET9EQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZbjCACKFO9Hp8Xwwg2nEM8DL3i+MlGaqxjIrcsb
WskuVOJjkAA4hMnrd7XvbpzJJusAquGqMd042ZCWtrNa1AwzCy0ZkYjDFNL27rXH
DqrHmJZowSoTHxlo8QKaevXH3ZZnp8TDz4IqaD0+UZx7DgZSOjR1a+feseh1Jn/V
9WBUJhNAFtKMiJBkTIpaDUk0E6OxIspdvlJurYmwUvDbfZKlpZrXHYKXSuUhFS9s
JX4Dqi5eF96Mctpi8GhaHGf7awPQf4oQBZfsXxhhS/efzX/v0HWqUPt40o2THi0F
ZbFFE3xAFaWisA+cbg8xnzJc8ZAwz2UmS6FgQ9lrqKyGN74buwgP
=spNi
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.14" from Heiko Stübner:
64bit Rockchip devicetree changes containing fixes for pinctrl typos
and the use of keep-power-in-suspend in non-sdio nodes as well as the
removal of the deprecated num-slots property from dwmmc nodes.
rk3328 gets support for spdif, io-domains and usb (including enablement
of usb on the evaluation board), while rk3368 gains support for spdif.
The biggest chunk of course aims for the rk3399 with a number of pcie
changes, support for the mali gpu, a new power-domain, sdmmc support
on the firefly board and dynamic-power-coefficients.
The gru family also gets support for their quite central pwm regulators
using the newly introduced vctrl regulator types.
* tag 'v4.14-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: update dynamic-power-coefficient for rk3399
arm64: dts: rockchip: add rk3328 spdif node
arm64: dts: rockchip: add rk3368 spdif node
arm64: dts: rockchip: enable sdmmc controller on rk3399-firefly
arm64: dts: rockchip: Add rk3328 io-domain node
arm64: dts: rockchip: kill pcie_clkreqn and pcie_clkreqnb for rk3399
arm64: dts: rockchip: change clkreq mode for rk3399-firefly
arm64: dts: rockchip: enable the GPU for RK3399-GRU
arm64: dts: rockchip: add ARM Mali GPU node for RK3399 SoCs
dt-bindings: gpu: add the RK3399 mali for rockchip specifics
arm64: dts: rockchip: remove abused keep-power-in-suspend
arm64: dts: rockchip: remove num-slots from all platforms
arm64: dts: rockchip: change clkreq mode for rk3399-evb
arm64: dts: rockchip: add SdioAudio pd control for rk3399
arm64: dts: rockchip: enable usb2 for RK3328 evaluation board
arm64: dts: rockchip: add usb2 nodes for RK3328 SoCs
arm64: dts: rockchip: set rk3399 dynamic CPU power coefficients
arm64: dts: rockchip: Use vctrl regulators for dynamic CPU voltages on Gru/Kevin
arm64: dts: rockchip: Update CPU regulator voltage ranges for Gru
arm64: dts: rockchip: fix typo in mmc pinctrl
* Add usb2.0 for R-Car H3 (r8a7795) ES2.0 SoC
* Add R-Car D3 (r8a77995) SoC and Draak board support
Adds minimal support for the R-Car D3 SoC and the Draak development
board, allowing to boot from a ramdisk using a serial console.
* Add Add VC6 clock generator to R-Car H3 (r8a7795)/Salvator-XS board
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
* Add missing second pair of DMA names to MSIOF nodes to
R-Car M3-W (r8a7796) SoC
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
* Add support for the DU to R-Car H3 (r8a7795) SoC
Add a compatible string and VSP links to the DU node. The H3 ES1.x and H3
ES2.0 are compatible save for the links to the VSPs that are described
explicitly in DT, so there's no need for a new ES2-specific compatible
string.
* Enable HDMI on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Enable DU on R-Car M3-W (r8a7796) Salvator-X board
* Enable I2C for DVFS on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Add Add DRIF support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Ramesh Shanmugasundaram says, "R-Car Gen3 DRIF is a SPI like receive only
slave device."
* Move CPG_AUDIO_CLK_I from board to soc files
Geert Uytterhoeven says, "The definition of CPG_AUDIO_CLK_I is
SoC-specific, not board-specific."
* Add IMR-LX4 support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Sergei Shtylyov says, "The image renderer light extended 4 (IMR-LX4) or
the distortion correction engine is a drawing processor with a simple
instruction system capable of referencing data on an external memory as
2D texture data and performing texture mapping and drawing with respect
to any shape that is split into triangular objects."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ehXW
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add usb2.0 for R-Car H3 (r8a7795) ES2.0 SoC
* Add R-Car D3 (r8a77995) SoC and Draak board support
Adds minimal support for the R-Car D3 SoC and the Draak development
board, allowing to boot from a ramdisk using a serial console.
* Add Add VC6 clock generator to R-Car H3 (r8a7795)/Salvator-XS board
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
* Add missing second pair of DMA names to MSIOF nodes to
R-Car M3-W (r8a7796) SoC
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
* Add support for the DU to R-Car H3 (r8a7795) SoC
Add a compatible string and VSP links to the DU node. The H3 ES1.x and H3
ES2.0 are compatible save for the links to the VSPs that are described
explicitly in DT, so there's no need for a new ES2-specific compatible
string.
* Enable HDMI on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Enable DU on R-Car M3-W (r8a7796) Salvator-X board
* Enable I2C for DVFS on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Add Add DRIF support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Ramesh Shanmugasundaram says, "R-Car Gen3 DRIF is a SPI like receive only
slave device."
* Move CPG_AUDIO_CLK_I from board to soc files
Geert Uytterhoeven says, "The definition of CPG_AUDIO_CLK_I is
SoC-specific, not board-specific."
* Add IMR-LX4 support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Sergei Shtylyov says, "The image renderer light extended 4 (IMR-LX4) or
the distortion correction engine is a drawing processor with a simple
instruction system capable of referencing data on an external memory as
2D texture data and performing texture mapping and drawing with respect
to any shape that is split into triangular objects."
* tag 'renesas-arm64-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
arm64: dts: renesas: r8a7795: add hsusb ch3 device node
arm64: dts: renesas: r8a7795: add usb-dmac ch2 and ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2.0 host ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2_phy ch3 device node
arm64: dts: renesas: r8a7795: Add usb companion property in EHCI
arm64: dts: renesas: Add Renesas Draak board support
arm64: dts: renesas: Add Renesas R8A77995 SoC support
arm64: renesas: Add Renesas R8A77995 Kconfig support
arm64: dts: r8a7795: salvator-xs: Connect DU dot clocks 0 and 3
arm64: dts: salvator-xs: Add VC6 clock generator
arm64: dts: r8a7796: Add missing second pair of DMA names to MSIOF nodes
arm64: dts: r8a7795: Add all MSIOF nodes
arm64: dts: r8a7795: Add support for the DU
arm64: dts: ulcb: Enable HDMI output
arm64: dts: ulcb: Add HDMI output connector
arm64: dts: r8a7796: m3ulcb: Add DU external dot clocks
arm64: dts: r8a7795: h3ulcb: Add DU external dot clocks
arm64: dts: ulcb: Add DU external dot clock sources
arm64: dts: r8a7796: salvator-x: Enable HDMI output
arm64: dts: r8a7796: salvator-x: Add DU external dot clocks
...
1. Remove deprecated and unneeded properties from Exynos boards.
2. Implement proper (working) support for USB On-The-Go on Exynos5433
TM2/TM2E boards.
-----BEGIN PGP SIGNATURE-----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=hQn1
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DTS ARM64 changes for v4.14" from Krzysztof Kozłowski:
1. Remove deprecated and unneeded properties from Exynos boards.
2. Implement proper (working) support for USB On-The-Go on Exynos5433
TM2/TM2E boards.
* tag 'samsung-dt64-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Remove num-slots from exynos platforms
arm64: dts: exynos: Add extcon property for TM2 and TM2E
arm64: dts: exynos: Fix wrong label for USB 3.0 controller node
arm64: dts: exynos: Remove the OF graph from DSI node
This patch adds the IOMMU node for the IOMMU that resides on the
Qualcomm MSM8916 platforms.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the Qualcomm Venus video codec node for the video
codec hardware residing on MSM8916 platforms.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch is to add watchdog binding for Hi3660 on Hikey960 board.
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhong Kaihua <zhongkaihua@huawei.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch reserves some memory in the DTS and sets up a
pstore device tree node to enable pstore support on HiKey960.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add support to hikey960 dts for the syscon-reboot-mode driver.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
There are two clusters on the Hi3660, the first one is Cortex-A53 based
and the other one is Cortex-A73 based. These two clusters have different
idle states.
Thanks to Daniel Lezcano's recent changes, the generic ARM cpuidle
driver can now support several clusters with different idle states, thus
supporting the big.Little architecture.
In addition to the WFI idle state which is the default shallowest state
for all ARM cpus, the Hi3660 supports the following states:
- CA53 CPUs:
- CPU_SLEEP: CPU power off state
- CLUSTER_SLEEP_0: Cluster power off state
- CA73 CPUs:
- CPU_NAP: CPU retention state
- CPU_SLEEP: CPU power off state
- CLUSTER_SLEEP_1: Cluster power off state
This patch adds the idle states description for the Hi3660 to the device
tree.
Cc: Kevin Wang <jean.wangtao@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch adds the Qualcomm Adreno GPU node that exists in the
MSM8916.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Enable USB host on Armada-8040-DB by adding USB PHY nodes for the
following ports:
- host 0 and 1 of CPM
- host 0 of CPS
These PHY are enabled by lanes coming from regulators based on two
I2C expanders.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add I2C expander and USB host PHY (host 0 and host 1) to enable
USB VBUS on USB ports of type A on Armada-7040-DB.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The NAND controller used in A7K/A8K is present on the CP110. It is
compatible with the pxa-nand driver.
However, due to the limiation of the pins available this controller is
only usable on the CPM for A7K and on the CPS for A8K.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add one PCIe host controller node for HiSilicon Hip07 SoC and enable it in
D05 board.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The pin controller of H5 has three IRQs at the chip's GIC, which
represents three banks of pinctrl IRQs. However, the device tree used to
miss the third IRQ of the pin controller, which makes the PG bank IRQ
not usable.
Add the missing IRQ to the pinctrl node.
Fixes: 4e36de179f ("arm64: allwinner: h5: add Allwinner H5 .dtsi")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
It adds the initial zx296718-pcbox board support with devices like
storage, audio and VGA output enabled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It enables the I2S sound card support, which is used to drive audio
through aud96p22 codec in case of TV output.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of simple-audio-card, audio-graph-card is recommended for audio
bindings. Let's change to it, so that the HDMI/SPDIF audio card can
align with the new I2S/Codec card which will be added later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We will enable PWM device to control voltage through pwm-regulator
support. So let's add voltage data into OPP table.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The default I2S0 parent clock AUDIO_24M can not be divided into required
sample rate in some cases, for example when 48KHz is needed. Change the
parent clock to AUDIO_99M which works for most sample rates.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It adds VGA device in zx296718.dtsi, so that boards with VGA connector
can enable the support by changing 'status' in board DTS file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
ls208xa supports another cpu idle state which is pw20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ls1088a supports another cpu idle state which is ph20 which saves
more power when cpu is idle.
It was implemented through psci firmware.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.
Fixes: 8164a84cca ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add NAND controller node to LD11 and LD20. Neither of them supports
the CS1 line, so pinctrl is set up for a single CS line.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the gmac2phy, make the gmac2phy work on
the rk3328-evb board.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gmac2phy controller of rk3328 is connected to integrated PHY
directly inside, add the node for the integrated PHY support.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add thermal zone and dynamic CPU power coefficients for rk3328
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.
Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
BPi M64 has an AP6212 Wi-Fi/Bluetooth combo module, and the Wi-Fi SDIO
card is connected to the mmc1 controller.
The pwrseq of the mmc1 (used to reset the card) used to missing, and the
out-of-band interrupt line of the card is not specified.
Fix these issues for proper Wi-Fi support of BPi M64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 board uses an AXP803 PMIC.
Enable the PMIC and its regulators.
As we have now proper regulators support, missing or dummy regulators
are changed to the correct ones.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Banana Pi M64 connects the USB host-only controller on A64 SoC to a USB
hub, which provided the two USB Type-A ports on the board.
Enable the USB host controller.
The OTG function of the Micro-USB port needs the drivevbus function of
the AXP803 driver implemented, so it's not enabled now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 96219b0048 ("arm64: allwinner: a64: add device tree for SoPine
with baseboard")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: 9702394374 ("arm64: allwinner: pine64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The EMAC Ethernet controller was enabled, but an accompanying alias
was not added. This results in unstable numbering if other Ethernet
devices, such as a USB dongle, are present. Also, the bootloader uses
the alias to assign a generated stable MAC address to the device node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: e729549990 ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
[wens@csie.org: Rewrite commit log as fixing a previous patch with Fixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
On UniPhier platform, some DTSI files are shared between arm and arm64.
Recently, inclusion of DT material of different architectures has been
supported by the build system level. Use #include <arm/...>, which
will work without relying on the exact same hierarchy as the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the smd-edge node for the adsp, to allow SMD communication with the
ADSP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the SMP2P nodes for the modem.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding required device node for couple of DWC3 controllers
present on msm8996 chipset to enable High speed and Super
speed USB support.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add required device node for QMP phy based 3-lane PCIe phy
present on msm8996 chipset to enable support for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding required device node for USB3 QMP phy present on
msm8996 chipset to enable support for the same. This phy
provides super speed usb functionality for dwc3 controller
on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding device node for QUSB2 phy and the required infrastructure
to enable support for the same. This phy is used by dwc3 controller
present on msm8996.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The adv7533 on this board needs a cec clock. Hook it up in the dtsi
to enable CEC for the HDMI transmitters.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace the obsolete compatible string for Coresight programmable
replicator with the new one.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Commit ed75d6a969 ("arm64: dts: qcom: Collapse usb support into
one node") breaks host mode support on apq8016-sbc boards. This
is because the mux driver (tc7usb40mu) hasn't been merged.
Without that driver, we can't toggle the GPIO going to the mux to
route out the D+/D- lines to the USB hub that's on the board.
One solution would be to totally revert this change, but that
opens us up to other problems when two USB drivers are operating
the same hardware block at the same time. Let's modify the DT so
that the USB controller is always in host mode and connected to
the hub so that things like USB keyboards and mouses work. This
is the mode that most people prefer anyway with these devices. We
also delete the usb-switch node because the binding was never
accepted upstream.
In the future, we can add muxing support and then update the DT
to support both modes at runtime. Patches to support this are
already on the mailing list.
Fixes: ed75d6a969 ("arm64: dts: qcom: Collapse usb support into one node")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds Broadcom SBA-RAID DT nodes for Stingray SoC.
The Stingray SoC has total 32 SBA-RAID FlexRM rings and it has
8 CPUs so we create 8 SBA-RAID instances (one for each CPU).
This way Linux DMAENGINE will have one SBA-RAID DMA device for
each CPU.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have two instances of FlexRM on Stingray. One for SBA RAID
offload engine and another for SPU2 Crypto offload engine.
This patch adds FlexRM mailbox controller DT nodes for Stingray.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add DT nodes for SATA host controllers and SATA PHYs
on Stingray SoC
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We have 8 instances of sp804 in Stingray SoC. Let's enable
it in Stingray DT.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Added MDIO multiplexer iproc DT node for Stingray, which contains
the child nodes of PCIe serdes, RGMII, SATA and USB phy MDIO slaves.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch enables stats for CCN-502 interconnect on Stingray.
Signed-off-by: Velibor Markovski <velibor.markovski@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
clock name of "audio_clkout" is used by Renesas sound driver.
This duplicated naming breaks its clock registering/unregistering.
Especially, when unbind/bind it can't handle clkout correctly.
This patch renames "audio_clkout" to "audio-clkout" to avoid
naming conflict.
Fixes: 8a8f181d2c ("arm64: renesas: salvator-x: use CS2000 as AUDIO_CLK_B")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.
This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
aliases node is identical for all boards, thus move it
to the common file ls208xa.dtsi.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two fixes to correct the EMAC blocks memory region size to match the
datasheet. One that converts raw A83T clock indices to macros from the
clk dt-binding header, completing the A83T sunxi-ng clk driver.
-----BEGIN PGP SIGNATURE-----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=aFvT
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.13" from Chen-Yu Tsai:
Two fixes to correct the EMAC blocks memory region size to match the
datasheet. One that converts raw A83T clock indices to macros from the
clk dt-binding header, completing the A83T sunxi-ng clk driver.
* tag 'sunxi-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
arm64: allwinner: sun50i-a64: Correct emac register size
ARM: dts: sunxi: h3/h5: Correct emac register size
All the fixes are for ARM64 mvebu:
- Fix the RTC interrupt on A7K/A8K which was missed when switching
from GIC to ICU
- Mark the A7K/A8K crypto engine as dma coherent
- Fix the number of GPIO on south bridge on Armada 3700
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWYHbmCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ZhfAJ9Z9aMBG1xd
vbRYBDdqPdntruTudwCcDtM9jS2nL+207JfeMD0WMs7sDdU=
=XwFM
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.13-2' of git://git.infradead.org/linux-mvebu into fixes
Pull "mvebu fixes for 4.13 (part 2)" from Gregory CLEMENT:
All the fixes are for ARM64 mvebu:
- Fix the RTC interrupt on A7K/A8K which was missed when switching
from GIC to ICU
- Mark the A7K/A8K crypto engine as dma coherent
- Fix the number of GPIO on south bridge on Armada 3700
* tag 'mvebu-fixes-4.13-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
arm64: dts: marvell: mark the cp110 crypto engine as dma coherent
arm64: dts: marvell: use ICU for the CP110 slave RTC
- 2 minor DT fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Z5d3
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.13-rc" from Kevin Hilman:
- 2 minor DT fixes
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl-s905x-libretech-cc: fixup board definition
ARM64: dts: meson-gx: use specific compatible for the AO pwms
The ESPRESSObin board exposes one of the SDHCI interfaces
via J1 uSD slot. This patch enables it.
Tested-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Zbigniew Bodek <zbodek@gmail.com>
[gregory.clement@free-electrons.com: removed "no-1-8-v"]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since the introduction of the CP110 dt files, the sata node was
misplaced. Move it at the right place. Thanks to this, the files are
completely ordered.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In both the CP110 master and slave description, the node describing
the RTC was at the wrong place when taking into account increasing
register addresses. Interestingly, it was not even at the same (wrong)
place in both files.
This commit adjusts that, making the master and slave descriptions
more aligned.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.
[gregory.clement@free-electrons.com: use commit log from Thomas]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the GPIO interrupts for the CP110.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Espressobin SBC has a USB2 interface available on J8. Let's
enable it.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a PMUv3, just like most ARMv8 cores.
Advertise the PMUv3 presence in the device tree, and wire its
interrupt. This allows the perf subsystem to work correctly.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Cortex-A53s that power the Armada-37xx SoCs are equipped with
a GIC CPU interface that gets enabled when coupled with a GICv3
interrupt controller, such as the GIC-500 on the this SoC.
Advertise the MMIO ranges provided by the CPUs, which enables
(among other things) GICv2 guests to run under a hypervisor such
as KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The GIC-500 integrated in the Armada-37xx SoCs is compliant with
the GICv3 architecture, and thus provides a maintenance interrupt
that is required for hypervisors to function correctly.
With the interrupt provided in the DT, KVM now works as it should.
Tested on an Espressobin system.
Fixes: adbc3695d9 ("arm64: dts: add the Marvell Armada 3700 family and
a development board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Fixes: afda007fed ("ARM64: dts: marvell: Add pinctrl nodes for Armada
3700")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since underscores('_') are not allowed in the device tree nodes names,
replace all of them with hyphen('-') in device node names. Note that
underscores are however allowed in labels.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use the new compatible for ATB programmable replicator in Juno.
Cc: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This patch describes the GPIO lines usage on the Nanopi K2 board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch describes the GPIO lines usage on the Khadas VIM board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: minor whitespace fix]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
