1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SRIOV mode, driver should not automatically start/stop
the mlx4_core upon sensing an HCA internal error -- doing this disables/enables
sriov, which will cause the hypervisor to hang if there are running VMs with
attached VFs.
In addition, on VMs the catas process should not run at all, since the HCA
error buffer is not available to VMs in the BARs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable internal loopback, always fill DMAC in control segment
when transmitting the packet, once this is done, the packet is subject
for loopback for if the DMAC mathces one of the multicast/unicast addresses
registered on the physical port.
In receive path if source MAC is our own MAC and we are not in selftest,
or not in force LB mode - drop this packet.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource tracker is used to track usage of HCA resources by the different
guests.
Virtual functions (VFs) are attached to guest operating systems but
resources are allocated from the same pool and are assigned to VFs. It is
essential that hostile/buggy guests not be able to affect the operation of
other VFs, possibly attached to other guest OSs since ConnectX firmware is not
tolerant to misuse of resources.
The resource tracker module associates each resource with a VF and maintains
state information for the allocated object. It also defines allowed state
transitions and enforces them.
Relationships between resources are also referred to. For example, CQs are
pointed to by QPs, so it is forbidden to destroy a CQ if a QP refers to it.
ICM memory is always accessible through the primary function and hence it is
allocated by the owner of the primary function.
When a guest dies, an FLR is generated for all the VFs it owns and all the
resources it used are freed.
The tracked resource types are: QPs, CQs, SRQs, MPTs, MTTs, MACs, RES_EQs,
and XRCDNs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing async events to slaves:
In SRIOV mode, each slave creates its own async EQ, but only the master can
register directly with the FW to receive async events. Async events which
should be passed to slaves (such as a WQ_ACCESS_ERROR for a QP owned by a slave)
are generated at the slave by the master using the GEN_EQE FW command.
Wrapper functions: mlx4_MAP_EQ_wrapper
Only the master can map an EQ. The slave commands to map their EQs arrive
at the master via the comm channel. The master then invokes the wrapper
function to do the work (and enter the resource in the tracking database).
New events: COMM_CHANNEL and FLR
The COMM_CHANNEL event arrives only at the master, and signals that
a slave has posted a command on the comm channel.
The FLR event is generated by the FW when a guest operating a VF
unexpectedly goes down.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTTs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
CQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
QPs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
SRQs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when
they start up to receive configuration information from the PF, such
as resource quotas for this VF, which ports should be used (currently
two), what protocol is running on the port (currently Ethernet ONLY,
or port not active).
2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
required here (the VF's MAC address must be substituted for the PFs
MAC address returned by the FW). We changed the invocation
in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.
3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
For now, we need only the multicast table member entry size
(log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed
here, because the data may be passed as is to the VF without modification).
In this command, we have added a GLOBAL_CAPS field for passing required
configuration information from FW to a VF (this field is to allow safely
adding new SRIOV capabilities which require support in VF drivers, too).
Bits will set here by FW in response to PF-driver configuration commands which
will activate as yet undefined new SRIOV features. The VF will test to see that
all required capabilities indicated by this field are supported (i.e., if a bit
is set and the VF driver does not recognize that bit, it must abort
its initialization). Currently, no bits are set.
4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts
have the port open. The PF context will not actually issue the FW close port command
until the last port user issues a CLOSE_PORT request.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled, pf and vfs communicate via shared comm channel.
The vf gets its side of the comm channel via a VF BAR.
Each VF (slave) creates its vHCR (virtual HCA Command Register),
Its DMA address is passed to the PF (master) using Communication Channel Register.
The same Register is used to notify the master of commands posted by the
slaves and for the master to pass events to the slaves, such as command completions
and asynchronous events.
The vHCR format is identical to the HCR format, except for the 'go' and 't' bits,
which are reserved in the vHCR. Posting commands to the vHCR is identical to
the way it is done with the HCR, albeit that the function/PF token fields are
used instead of the HCR go bit.
Specifically:
- When the function prepares a new command in the vHCR, it issues the Post_vHCR_cmd
communication channel command and toggles the value of the function token;
when PF token has an equal value, the command has been accepted and a new command may be posted.
- When the PF detects a Post_vHCR_cmd command, it concludes that a new command is available in the vHCR;
after processing the command, the PF toggles the PF token to match the function token.
When the 'e' bit is not set, the completion of a Post_vHCR_cmd command also indicates
the completion the vHCR command. If, however, the 'e' bit is set, the completion of a
Post_vHCR_cmd command only indicates that the vHCR command has been accepted for execution by the PF.
Function commands are processed by the PF as follows:
-DMA (using the ACCESS_MEM command) the vHCR image into a shadow buffer.
-Validate that the opcode is non-privileged, and that the opcode- and input-modifiers are legal.
-DMA the in-box (if required) into a shadow buffer.
-Validate the command:
o Resource ranges (e.g., QP ranges).
o Partition key.
o Ranges of referenced resources (e.g., CQs within QP contexts).
-If the 'e' bit is set
o complete the Post_vHCR_cmd command
-Execute the command on the HCR.
-DMA the results to the vHCR out-box (if required).
-If the 'e' bit is set
o Indicate command completion by generating a completion event using the GEN_EQE command
-Otherwise
o DMA the command status to the vHCR
o Complete the Post_vHCR_cmd command
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrillin <yevgenyp@mellanox.com>
Signed-off-by: Liran Liss <liranl@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.
Change the allocator to return only 17 bits for the PD. The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mask now has additional state.
Port can be set as "none". In this case neither the mlx4_en or mlx4_ib
drivers take ownership of the port.
In multifunction mode there is an option to set the vfs as single ported devices.
(in single function mode, both physical ports belong to same function)
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use adapter->num_vfs (and not the module param) to store the actual
number of vfs created. Use the same variable to reflect SRIOV
enable/disable state. So, drop the adapter->sriov_enabled field.
- use for_all_vfs() macro in VF configuration code
- drop the "vf_" prefix for the fields of be_vf_cfg; the prefix is
redundant and removing it helps reduce line wrap
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool "-g" option is supposed to report the max queue length and
user modified queue length for RX and TX queues. be2net doesn't support
user modification of queue lengths. So, the correct values for these
would be the max numbers.
be2net incorrectly reports the queue used values for these fields.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e52fcb2462 newly allocated
skb for small packets are not updated properly and dropped by stack.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
disable Tx vlan offloading in certain cases.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update pmem_fifo_overflow_drop, rx_priority_pause_frames counters.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is missing initialization of NO_FCOE_FLAG and NO_ISCSI*FLAGS
when CONFIG_CNIC is not selected.
This causes panic during driver load since commit
1d187b34da where NO_FCOE tested
unconditionally (outside #ifdef BCM_CNIC structure) and
accessed fp[FCOE_IDX] which is not allocated.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let caller know the result of adding/removing vlan id to/from vlan
filter.
In some drivers I make those functions to just return 0. But in those
where there is able to see if hw setup went correctly, return value is
set appropriately.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .remove code is broken in several ways.
- mdiobus_unregister() is called twice for the same object in case of dual FEC
- phy_disconnect() is being called when the PHY is already disconnected
- the requested IRQ(s) are not freed
- fec_stop() is being called with the inteface already stopped
All of those lead to kernel crashes if the remove function is actually used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additionally to setting the ETHER_EN bit in FEC_ECNTRL the MII/RMII
setting in FEC_R_CNTRL needs to be preserved to keep the MII interface
functional.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MAC address is supplied via platform_data it should be OK as
it is and should not be modified in case of a dual FEC setup.
Also copying the MAC from platform_data to the single 'macaddr'
variable will overwrite the MAC for the first interface in case of a
dual FEC setup.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
prevent calling request_irq() with a known invalid IRQ number and
preserve the return value of the platform_get_irq() function
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon detection of a FDX/HDX change the interface is restarted twice.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The con_id is actually not needed for clk_get().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove some bogus whitespace
- remove line wraps from printk messages
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.122.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to return the flow control configuration
rather than the flow control status through the ETHTOOL_GPAUSEPARAM
ioctl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to track the autonegotiation advertisements of the
link partner and report them through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates tg3_adv_1000T_flowctrl_ok() into
tg3_copper_is_advertising_all() and renames the function
tg3_phy_copper_an_config_ok().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3 has a place to store stats, but doesn't really use it. This patch
modifies the driver so that stats are saved across chip resets and gets
cleared across close / open calls.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the ethtool stats member from the tg3 device
structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide FCoE and iSCSI statistics to management firmware if
CONFIG_CNIC is not set. Some needed structure fields are not defined
without CONFIG_CNIC.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2df1a70aaf "bnx2x: Support
for byte queue limits" has introduced an asymmetry in usage of
netdev_tx_completed_queue and netdev_tx_sent_queue. Missing
call to netdev_tx_sent_queue causes the crash during ethtool -t.
The patch adds the missing call.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to send driver capabilities, settings and statistics to
management firmware.
[ Redone using many local variables, removed many unnecessary inlines,
and put #defines at the left margin suggested by Joe Perches ]
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support copying MAC addresses to firmware query structure.
[ Fixed up style and formatting errors noted by DaveM and Joe Perches ]
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FCoE statistics support for FCoE capable devices.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Priority flow control counters for ethtool -S.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ded19addf9 ('pasemic_mac*: Move
the PA Semi driver') inadvertently split pasemi_mac into two separate
modules with unresolved symbols. Change it back into a single module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 92fc43b415, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
-> rtl_hw_reset
-> rtl8169_init_ring_indexes
What about returning to the original state ?
rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.
The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).
rtl8169_hw_reset is used by:
1. rtl8169_down
Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
anyway.
2. rtl8169_pcierr_interrupt
Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
Indexes should not be set. This is the job of rtl8169_reset_task anyway.
The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
