Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we mark AN as enabled at boot time, rather than leaving
it disabled. This is noticable if your SFP module is fiber, and
it supports faster speeds than 1G with 2.5G support in place.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the ethtool settings, ensure that the validated PHY
interface mode is propagated to the current link settings, so that
2500BaseX can be selected.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several error paths in xgene_mdio_probe(),
where clk is left undisabled. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observed on the 88e1512 in SGMII-to-Copper mode, negotiating pause
is unreliable. While the pause bits can be set in the advertisment
register, they clear shortly after negotiation with a link partner
commences irrespective of the cause of the negotiation.
While these bits may be correctly conveyed to the link partner on the
first negotiation, a subsequent negotiation (eg, due to negotiation
restart by the link partner, or reconnection of the cable) will result
in the link partner seeing these bits as zero, while the kernel
believes that it has advertised pause modes.
This leads to the local kernel evaluating (eg) symmetric pause mode,
while the remote end evaluates that we have no pause mode capability.
Since we can't guarantee the advertisment, disable pause mode support
with this PHY when used in SGMII-to-Copper mode.
The 88e1510 in RGMII-to-Copper mode appears to behave correctly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
88E1145 also need this autoneg errata.
Fixes: f289978835 ("net: phy: marvell: Limit errata to 88m1101")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in SGMII-to-Copper mode, the fiber page is used for the MAC facing
link, and does not require configuration of the fiber auto-negotiation
settings. Avoid trying.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meson_gxl_read_status is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'meson_gxl_read_status' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that all mdio devices populate the struct device fwnode pointer
as well as the of_node pointer to allow drivers that wish to use
fwnode APIs to work.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY has the BMCR_PDOWN bit set, it may decide to ignore writes
to other registers, or reset the registers to power-on defaults.
Micrel PHYs do this for their interrupt registers.
The current structure of phylib tries to enable interrupts before
resuming (and releasing) the BMCR_PDOWN bit. This fails, causing
Micrel PHYs to stop working after a suspend/resume sequence if they
are using interrupts.
Fix this by ensuring that the PHY driver resume methods do not take
the phydev->lock mutex themselves, but the callers of phy_resume()
take that lock. This then allows us to move the call to phy_resume()
before we enable interrupts in phy_start().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
Fixes: 7334b3e47a ("net: phy: Add Meson GXL Internal PHY driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not support SFP modules which require the address change sequence
as detailed by SFF 8472 revision 1.22 section 8.9. Warn when these
modules are inserted, and treat them as SFF8079 modules for ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two bits in the option word for the RX_LOS signal. One
reports that the RX_LOS signal is active high, the other reports that
it is active low. When both or neither are set, the result is not
well defined in the specification.
Rather than assuming that neither set means normal RX_LOS, take this
as meaning no RX_LOS signal available, thereby ignoring the signal.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The options word is a be16 quantity, so we need to test the flags
having converted the endian-ness. Convert the flag bits to be16,
which can be optimised by the compiler, rather than converting a
variable at runtime.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix obvious typo that first return value is set but not checked.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 10G PHY driver supports different hardware revisions, which
have their bits 3..0 differing. To get the correct revision number these
bits should be ignored. This patch fixes this by using the already
defined MARVELL_PHY_ID_MASK (0xfffffff0) instead of the custom
0xffffffff mask.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/phy/cortina.o
see include/linux/module.h for more information
This adds the license as "GPL", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b94d22d94a "ARM64: dts: meson-gx: add external PHY
interrupt on some platforms" ethernet stopped working on my Odroid-C2
which has a RTL8211F phy.
It turned out that no interrupts were triggered. Further analysis
showed the register INER can't be altered on page 0.
Because register INSR needs to be accessed via page 0xa43 I assumed
that register INER needs to be accessed via some page too.
Some brute force check resulted in page 0xa42 being the right one.
With this patch the phy is working properly in interrupt mode.
Fixes: 3447cf2e9a ("net/phy: Add support for Realtek RTL8211F")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we create a LED trigger for any link speed known to a PHY.
These triggers only fire when their exact link speed had been negotiated
(they aren't cumulative, that is, they don't fire for "their or any higher"
link speed).
What we are missing, however, is a trigger which will fire on any link
speed known to the PHY. Such trigger can then be used for implementing a
poor man's substitute of the "link" LED on boards that lack it.
Let's add it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, phy_led_trigger_change_speed() is handling a "no link" condition
like it was some kind of an error (using "goto" to a code at the function
end).
However, having no link at PHY is an ordinary operational state, so let's
handle it in an appropriately named separate function so it is more obvious
what the code is doing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/phy/phylink.c:570:6: warning:
symbol 'phylink_phy_change' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
include/gpio.h does not contain the references we want, we should be including
linux/gpio/consumer.h instead.
Fixes: 7397005545 ("sfp: add SFP module support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Perform a number of stylistic changes to phylink.c, sfp.c and sfp-bus.c:
- align with netdev-style comments
- align function arguments to the opening parenthesis
- remove blank lines
- fixup a few lines over 80 columns
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return error code to EINVAL if the MAC
address is not valid in the set_wol function.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83822 10/100Mbit ethernet phy.
The DP83822 provides flexibility to connect to a MAC through a
standard MII, RMII or RGMII interface.
In addition the DP83822 needs to be removed from the DP83848 driver
as the WoL support is added here for this device.
Datasheet:
http://www.ti.com/product/DP83822I/datasheet
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is
not enough to represent interrupt numbers on all architectures. Hence
PHY interrupt numbers may be truncated during printing.
Increase the buffer size from 4 to 8 bytes to fix this.
Fixes: 5e369aefdc ("net: stmmac: Delete dead code for MDIO registration")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 2d55173e71 ("phy: add generic function to support
ksetting support"), we lost the ability to report the transceiver type
like we used to. Now that we have added back the transceiver type to
ethtool_link_settings, we can report it back like we used to and have no
loss of information.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the integration of PHYLINK, the configuration option which
used to be under the PHY infrastructure menu in menuconfig ended
up one level up (the network device driver section)
By placing PHYLINK option right after PHYLIB entry, it broke the
way Kconfig used to build the menu. See kconfig-language.txt, section
"Menu structure", 2nd method.
This is fixed by placing the PHYLINK option just before PHYLIB.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clear Speed Selection in MDIO control register(0x10),
ie, clear bits 6 and 13 to zero while keeping other bits same.
Before AND operation,The Mask value has to be perform with bitwise NOT
operation (ie, ~ operator)
This patch clears current speed selection before writing the
new speed settings to gmii2rgmii converter
Fixes: f411a6160b ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Fahad Kunnathadi <fahad.kunnathadi@dexceldesigns.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RTL8201F phy-id and the related functions to the driver.
The original patch is as follows:
https://patchwork.kernel.org/patch/2538341/
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the definition of page select register from
RTL8211F_PAGE_SELECT to RTL821x_PAGE_SELECT to use it across models.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 95b80bf3db ("mdio_bus:
Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB
checks for NULL descriptors, so it's safe to drop them, but it is not
when CONFIG_GPIOLIB is disabled in the kernel. If we do call
gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings
coming from the inline stubs declared in include/linux/gpio/consumer.h.
Fixes: 95b80bf3db ("mdio_bus: Remove unneeded gpiod NULL check")
Reported-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Rx rate select control gpio property name match the documented
binding. This would make the addition of 'rate-select1-gpios' for SFP+
support more natural.
Also, make the MOD-DEF0 gpio property name match the documentation.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is no longer used, the logging function was changed by commit
fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array bcm7xxx_suspend_cfg A on the stack, instead
make it static. Makes the object code smaller by over 300 bytes:
Before:
text data bss dec hex filename
6351 8146 0 14497 38a1 drivers/net/phy/bcm7xxx.o
After:
text data bss dec hex filename
5986 8210 0 14196 3774 drivers/net/phy/bcm7xxx.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_uninit() call put_device (unconditionally) because of
of_mdio_find_bus() in mdio_mux_init.
But of_mdio_find_bus is only called if mux_bus is empty.
If mux_bus is set, mdio_mux_uninit will print a "refcount_t: underflow"
trace.
This patch add a get_device in the other branch of "if (mux_bus)".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix an old information that mdio-mux-mmioreg can only handle
8bit registers.
This is not true anymore.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the driver version information because this information
is not useful in an upstream kernel driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix checkpatch warning about unnecessary 'out of memory'
message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
