LP5521 and LP5523 data structures have common features.
Use common lp55xx data structures rather than chip specific data.
Legacy code in probe is replaced with this new data structures.
lp55xx_chip : Common data between lp5521_chip and lp5523_chip
lp55xx_led : Common LED structure between lp5521_led and lp5523_led
lp55xx_platform_data : Common platform data between lp5521_platform_data and
lp5523_platform_data
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Change the name of chip data structure and platform data.
This patch is a preceding step for cleaning up lp5521/5523 probe and remove.
These data will be replaced with new lp55xx common data structures
in next patch.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch supports basic common driver code for LP5521, LP5523/55231 devices.
( Driver Structure Data )
lp55xx_led and lp55xx_chip
In lp55xx common driver, two different data structure is used.
o lp55xx_led
control multi output LED channels such as led current, channel index.
o lp55xx_chip
general chip control such like the I2C and platform data.
For example, LP5521 has maximum 3 LED channels.
LP5523/55231 has 9 output channels.
lp55xx_chip for LP5521 ... lp55xx_led #1
lp55xx_led #2
lp55xx_led #3
lp55xx_chip for LP5523 ... lp55xx_led #1
lp55xx_led #2
.
.
lp55xx_led #9
( Platform Data )
LP5521 and LP5523/55231 have own specific platform data.
However, this data can be handled with just one platform data structure.
The lp55xx platform data is declared in the header.
This structure is derived from leds-lp5521.h and leds-lp5523.h
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Chip specific function is configured when the device is initialized.
So _configure() is moved to each device init function.
If chip configuration gets failed, the device is de-initialized in
each _init_device(), not probe().
For compile error fix, function type declarations are added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use explicit each driver function rather than raw command.
These function will be merged into the lp55xx common driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make LED unregistration code simple, new function, _unregister_leds()
is added in each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make LED initialization code simple, new function, _register_leds()
is added at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Device de-initialization code is moved to _deinit_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make _probe() simple, device initialization code is moved to
_init_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
leds-lp5521:
When 'lp5521_init_device()' gets failed, error handling should be 'fail1'
rather than 'fail2'.
fail1: releasing platform resource and return code
fail2: releasing allocated LED devices with handling 'fail1'
The 'lp5521_init_device()' is called before creating LED devices.
Thus, 'goto fail1' is proper error handler of this function.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This macro is used to create a struct pci_device_id array.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
I spent a few minutes to understand why the code catching the mismatch case
by checking if k is 0 or not. And the code using "k - 1" as array index is
unusual.
This patch checks acceptable rate from the lowest rate, and then we don't need
to subtract k by 1. This change improves the readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add lm3530_led_enable() and lm3530_led_disable() helper functions.
This ensures setting drvdata->enable to correct status if regulator_disable
fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The lp8788-keyled is a platform driver of lp8788-mfd. The platform
device is allocated when mfd_add_devices() is called in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case
of resource managed mem alloc, registering led device and device
kernel messages.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The DT binding for the pwm-leds devices are similar to the gpio-leds type.
LEDs are represented as sub-nodes of the pwm-leds device.
The code for handling the DT boot is based on the code found in the
leds-gpio driver and adapted to use PWMs instead of GPIOs.
To avoid having custom cleanup code in case of DT boot the newly created
devm_of_pwm_get() API is used to get the correct PWM instance.
For usage see:
Documentation/devicetree/bindings/leds/leds-pwm.txt
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The code looks more nicer if we use:
while (i--)
instead:
if (i > 0)
for (i = i - 1; i >= 0; i--)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In order to be able to add device tree support for leds-pwm driver we need
to rearrange the data structures used by the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Update the driver to use the new API for requesting pwm so we can take
advantage of the pwm_lookup table to find the correct pwm to be used for the
LED functionality.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Support added only for leds (not for gpio's).
(cooloney@gmail.com: fix 2 building errors)
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
if (flags & GPIOF_DIR_IN)
err = gpio_direction_input(gpio);
else
err = gpio_direction_output(gpio,
(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}
The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
If "buf" wasn't equal to LP5521_REG_R_CURR_DEFAULT the probe fails but
we still return zero. I've changed it to print an error message and
return -EINVAL.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Silences checkpatch warnings related to the use of printks.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following issues:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following type of warnings:
WARNING: Prefer netdev_warn(netdev, ... then dev_warn(dev, ...
then pr_warn(... to printk(KERN_WARNING ...
WARNING: quoted string split across lines
While at it also fix a coding style issue w.r.t braces.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch error:
ERROR: space prohibited before that ':' (ctx:WxE)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ...
then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: please, no space before tabs
FILE: leds/leds-pwm.c:29:
^Iunsigned int ^I^Iactive_low;$
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch error and warnings:
WARNING: please, no space before tabs
ERROR: trailing whitespace
WARNING: quoted string split across lines
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
devm_gpio_request_one is device managed and makes error handling
and cleanup simpler.
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
devm_gpio_request_one is device managed and makes error handling
and cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EINVAL. Silences the following smatch warning:
drivers/leds/leds-lp3944.c:89 lp3944_reg_read() info:
why not propagate 'tmp' from i2c_smbus_read_byte_data() instead of -22?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EIO. Silences the following smatch warning:
drivers/leds/leds-lp5523.c:174 lp5523_read() info:
why not propagate 'ret' from i2c_smbus_read_byte_data() instead of -5?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EIO. Silences the following smatch warning:
drivers/leds/leds-lp5521.c:155 lp5521_read() info:
why not propagate 'ret' from i2c_smbus_read_byte_data() instead of -5?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Implements a "led_trigger_rename" function to rename a trigger with
proper locking.
This assumes that led name was originally allocated in non-constant
storage.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
We don't need these sysfs files to be world writable or group writable.
These files are write-only, change them to S_IWUSR (0200).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
We don't need the sysfs file to be world writable or group writable.
This file is write-only, change it to S_IWUSR (0200).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_kfree function allocates memory that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_kfree in probe or remove functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fixes build warnings as below:
drivers/leds/leds-lp5523.c: In function 'lp5523_selftest':
drivers/leds/leds-lp5523.c:496:18: warning: 'adc' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:471:5: warning: 'vdd' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c: In function 'lp5523_probe':
drivers/leds/leds-lp5523.c:252:9: warning: 'status' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:201:5: note: 'status' was declared here
If lp5523_read() returns an error, problems will happen. Thus,
when lp5523_read() returns an error, it should be handled.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch makes leds-gpio's probe() return -EPROBE_DEFER if any of the gpios
to register are deferred themselves. This makes a change of
gpio_leds_create_of()'s return value necessary: Instead of returning NULL on
error, we now use ERR_PTR() error coding.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Seeing the following every time the CPU enters or leaves idle on a
Beagleboard:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
no locks held by swapper/0/0.
[<c001659c>] (unwind_backtrace+0x0/0xf8) from [<c05aaa7c>] (mutex_lock_nested+0x24/0x380)
[<c05aaa7c>] (mutex_lock_nested+0x24/0x380) from [<c043bd1c>] (ledtrig_cpu+0x38/0x88)
[<c043bd1c>] (ledtrig_cpu+0x38/0x88) from [<c000f4b0>] (cpu_idle+0xf4/0x120)
[<c000f4b0>] (cpu_idle+0xf4/0x120) from [<c07e47c8>] (start_kernel+0x2bc/0x30c)
Miles Lane has reported seeing similar splats during system suspend.
The mutex in struct led_trigger_cpu appears to have no function: it
resides in a per-cpu data structure which never changes after the
trigger is registered. So just remove it.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Bryan Wu <roc@roc-samos.(none)>
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (24 commits)
leds: add output driver configuration for pca9633 led driver
leds: lm3642: Use regmap_update_bits() in lm3642_chip_init()
leds: Add new LED driver for lm3642 chips
leds-lp5523: Fix riskiness of the page fault
leds-lp5523: turn off the LED engines on unloading the driver
leds-lm3530: Fix smatch warnings
leds-lm3530: Use devm_regulator_get function
leds: leds-gpio: adopt pinctrl support
leds: Add new LED driver for lm355x chips
leds-lp5523: use the i2c device id rather than fixed name
leds-lp5523: add new device id for LP55231
leds-lp5523: support new LP55231 device
leds: triggers: send uevent when changing triggers
leds-lp5523: minor code style fixes
leds-lp5523: change the return type of lp5523_set_mode()
leds-lp5523: set the brightness to 0 forcely on removing the driver
leds-lp5523: add channel name in the platform data
leds: leds-gpio: Use of_get_child_count() helper
leds: leds-gpio: Use platform_{get,set}_drvdata
leds: leds-gpio: use of_match_ptr()
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
the pca9633 leds driver can be used in open-drain or totem pole (a.k.a.
push/pull) output driver mode; default is the later
the patch allows to set the output driver mode using platform data (similar to
configuration inferface provided by the tca6507 led driver)
v2: move leds-pca9633.h to include/linux/platform_data/ (Bryan Wu)
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use regmap_update_bits() to replace regmap_read() + regmap_write().
With this patch, we only show the error message when regmap_update_bits()
fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong<gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is a general version for LM642 led chip of TI.
LM3642 :
The LM3642 is a 4MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current
white LED.
The LM3642 is controlled via an I2C-compatible interface.
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The last attribute should be terminated as NULL because any member of
attribute structure is accessed while adding the sysfs file.
If not, invalid address may cause the page fault problem.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The LP5523 has 3 engines which are used for running LED patterns.
These engines should be off while unloading the driver.
Obviously, LP5523 platform data are used for releasing the resource
such like enable()/release_resource(), but these are not mandatory.
Therefore this patch is required without the platform data dependency.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Device managed functions are already used in this file.
Hence convert regulator_get() too to use it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Adopt pinctrl support to leds-gpio driver based on leds-gpio
device pointer, pinctrl driver configure SoC pins to GPIO
mode according to definitions provided in .dts file.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This driver is a general version for LM355x,lm3554 and lm3556,led chips of TI.
LM3554 :
The LM3554 is a 2 MHz fixed-frequency synchronous boost
converter with 1.2A dual high side led drivers.
Datasheet: www.ti.com/lit/ds/symlink/lm3554.pdf
LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf
(bryan.wu@canonical.com: use flush_work() to replace flush_work_sync() which is
deprecated)
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
LP5523 driver supports both LP5523 and LP55231. The i2c device id
is one of the two - lp5523 or lp55231. So it's better to use
matching i2c device id while enumerating the device and naming LED
channels.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
To support LP55231 device, the device id is added. Additionally,
the i2c driver name is changed from lp5523 to lp5523x.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
New TI LP55231 device has same I2C register layout as LP5523. Therefore,
all of LED operations can be shared with the LP5523 driver.
To support new LP55231 device explicitly, the device description
is added in the configuration file.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Some triggers create sysfs files when they are enabled. Send a uevent
"change" notification whenever the trigger is changed to allow userspace
processes such as udev to modify permissions on the new files.
A change notification will also be sent during registration of led class
devices or led triggers if the default trigger of an led class device
is found.
(bryan.wu@canonical.com: rename trigger to trig to fix the build error)
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
(a) use LP5523_ENABLE rather than magic number 0x40
(b) use min_t() in lp5523_mux_parse()
(c) skip while loop and just return if invalid command
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The return value of this function is not handled any place, so
make it as void type.
And three if-statements are replaced with switch-statements.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Turning off the brightness of each channel is required
when removing the driver.
So use flush_work() rather than cancel_work_sync() to execute
remaining brightness works.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The name of each led channel is configurable.
If the name is NULL, just use the channel id for making the channel name
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use the wrapper functions, so we can directly pass a struct
platfrom_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Instead of having to define the match table to NULL if CONFIG_OF isn't
set, use the of_match_ptr() macro which will do this for us.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Delay execution of led_set_brightness() if need to stop soft-blink
timer.
This allows led_set_brightness to be called in hard-irq context even if
soft-blink was activated on that LED.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
There are more variants of Clevo M5x0V laptops and Positivo Mobile is just one of them.
Another one is UMAX VisionBook 2400WXC. Use only generic Clevo DMI strings to match all
variants.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Enable autoloading of leds-clevo-mail by using MODULE_DEVICE_TABLE.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Since the resources of 88pm860x leds are changed from IORESOURCE_IO
to IORESOURCE_REG that is register offset, change the original
self-defined IORESOURCE_IO to register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This reverts commit a0193cbee0.
The problem with the original commit was that it caused a warning with
the MMC trigger calling del_timer_sync from hard-irq context.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
We need to do left shift (cfg->num + LP8788_ISINK_SCALE_OFFSET) bits for
updating scale configuration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Attempting to consolidate the ARM LED code, this removes the
custom RealView LED trigger code to turn LEDs on and off in
response to CPU activity and replace it with a standard trigger.
(bryan.wu@canonical.com:
It introduces several syscore stubs into this trigger.
It also provides ledtrig_cpu trigger event stub in <linux/leds.h>.
Although it was inspired by ARM work, it can be used in other arch.)
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jochen Friedrich <jochen@scram.de>
at default case of switch we return with out unlocking the mutex.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use the error codes from the lower levels instead of -ENODEV.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This can return without freeing the bl_work struct. Also there was no
check for allocation failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
TI LP8788 PMU has the current sink as the keyboard led driver.
The brightness is controlled by the i2c commands.
Configurable parameters can be defined in the platform side.
Patch v2.
(a) use workqueue on changing the brightness
(b) use mutex_lock/unlock when the brightness is set
and the led block of lp8788 device is enabled
(c) remove err_dev on _probe()
: just return as returned value if any errors
(d) replace module_init/exit() with module_platform_driver()
(e) add led configuration structure and loading them by default
if platform data is null
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add driver for BlinkM device to drivers/leds/.
Add entry to MAINTAINERS file.
Add documentation in Documentation/leds/.
A BlinkM is a RGB LED controlled through I2C.
This driver implements an interface to the LED framework
and another sysfs group to access the internal options
of the BlinkM.
rev6: Use module_i2c_driver().
rev5: Removed own workqueue in favor of events wq.
rev4: Fixed comments by Bryan Wu.
rev3: Fixed issues found by Jonathan Neuschäfer.
(bryan.wu@canonical.com: remove 2 trailing whitespace)
Signed-off-by: Jan-Simon Möller <jansimon.moeller@gmx.de>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
It is not necessary to call max8997_update_reg() twice just for updating
MAX8997_REG_LEN_CNTL register. With proper val and mask arguments to
max8997_update_reg() call, this can be done in one max8997_update_reg() call.
And then we can remove max8997_led_clear_mode() function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
why?
because if the led_classdev_register fails we wont do gpio free
because using devm_ functions, there is no need for error paths
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API instead.
This patch also adds gpio_request/gpio_free call for API corectness.
It is a prerequisite for removal of the S3C24XX SoC specific
arch/arm/plat-samsung/include/gpio-fns.h header.
Tested on Micro2440-SDK.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use the device managed resource API for simplifying
the error/driver remove paths.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
the platform_set_drvdata (pdev, NULL) to be set at the remove of the
driver, as we have set the platform data to led at probe.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Using devm_kzalloc will remove all the error checks and the frees are automatically done at the driver unload side.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Inside the error handling in lp5523_init_led(), there is a place that
calls to led_classdev_unregister(). When we unregister the LED drivers,
it tries to set the brightness to OFF. In this driver setting the
brightness is done through a work queue and the work queue hasn't been
initialized yet.
The result is that we trigger a WARN_ON() in the __queue_work().
The fix is to move the INIT_WORK() in front of the call to
lp5523_init_led().
Matt Renzelmann found this using a bug finding tool.
Reported-by: Matt Renzelmann <mjr@cs.wisc.edu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf
Tested on OMAP4430
(bryan.wu@canonical.com: use module_i2c_driver() rather than
lm3556_init/lm3556_exit for code simplicity; fixed some typo
pointed out by Rob Landley)
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Kim, Milo <Milo.Kim@ti.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
the ret is got the status returned by the
led_classdev_register, returning ret if the
led_classdev_register fails and returning 0
if the led_classdev_register success, can be done
by doing just "return ret" at the end.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
drivers/leds/led-core.c:56:6: sparse: symbol 'led_blink_setup' was not declared. Should it be static?
drivers/leds/led-triggers.c:233:6: sparse: symbol 'led_trigger_blink_setup' was not declared. Should it be static?
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Fix led_trigger_event() to use led_set_brightness() instead of
__led_set_brightness(), so that any pending blink timer is stopped before
setting the new brightness value. Without this fix LED status may be
overridden by a pending timer.
This allows a trigger to use a mix of led_trigger_event(),
led_trigger_blink() and led_trigger_blink_oneshot() without races.
(applied over: leds: Rename led_brightness_set() to led_set_brightness())
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Rename leds internal interface led_set_brightness() to __led_set_brightness()
to reduce confusion between led_set_brightness() and the external interface
led_brightness_set(). led_brightness_set() cancels the timer and then calls
led_set_brightness().
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add oneshot trigger to blink a led with configurale parameters via
sysfs.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Move led_stop_software_blink() code into led_brightness_set() to ensure
software blink timer is stopped and cleared when changing trigger.
Also use led_set_brightness() instead of calling
led_cdev->brightness_set() directly to keep led_cdev->brightness
consistent with current LED status.
This ensure proper cleaning when changing triggers, as without this fix
a LED may be turned off while leaving it's led_cdev->brightness = 1,
leading to an erratic software-blink behaviour.
The problem was easy to reproduce by changing the trigger from "timer"
to "oneshot".
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Convert ledtrig-ide-disk code to use the generic API for one-shot LED
blinking.
This patch changes slightly the behaviour of the trigger, as while the
original version kept the LED on under heavy activity, the new one keeps
a constant on-off blink at 1 / (2 * BLINK_DELAY) Hz.
(bryan.wu@canonical.com: remove 2 useless included header files)
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add two new functions, led_blink_set_oneshot and
led_trigger_blink_oneshot, to be used by triggers for one-shot blink of
led devices.
This is implemented extending the existing software-blink code, and uses
the same timer and handler function.
The behavior of the code is to do a blink-on, blink-off sequence when
the function is called, ignoring other calls until the sequence is
completed so that the leds keep blinking at constant rate if the
functions are called repeatedly.
This is meant to be used by drivers which needs to trigger on sporadic
event, but doesn't have clear busy/idle trigger points.
After the blink sequence the led remains off. This behavior can be
inverted setting the "invert" argument, which blink the led off, than on
and leave the led on after the sequence.
(bryan.wu@canonical.com: rebase to commit 'leds: don't disable blinking
when writing the same value to delay_on or delay_off')
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Otherwise, I got below build error when CONFIG_LEDS_CLASS=m.
LD init/built-in.o
drivers/built-in.o: In function `asic3_led_probe':
clkdev.c:(.devinit.text+0x4680): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `r_tpu_probe':
clkdev.c:(.devinit.text+0x4838): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `asic3_led_remove':
clkdev.c:(.devexit.text+0x564): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `r_tpu_remove':
clkdev.c:(.devexit.text+0x5a0): undefined reference to `led_classdev_unregister'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Fixed a coding style issue relating to trailing
white space error found by checkpatch.pl tool in drivers/leds/led-class.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Function led_set_software_blink() assumes that blink timer is still running,
but commit 488bc35bf4 introduced disabling
of blink timer before each call to led_set_software_blink().
Correct led_software_blink():
1) remove protection against reprogramming blink timer to the same values,
because it only disables blinking now,
2) remove unnecessary call to led_stop_software_blink().
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Add sub-driver for the LEDs on National Semiconductor / TI LM3533 lighting
power chips.
The chip provides 256 brightness levels, hardware accelerated blinking as
well as ambient-light-sensor and pwm input control.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Rob Landley <rob@landley.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When issuing the following command:
for I in 0 1 2 3 4 5 6 7; do
echo 0 > /sys/class/leds/pca955x\:${I}/brightness;
done
It is possible that all the pca955x_read_ls calls are done sequentially
before any pca955x_write_ls call is done. This updates the LS only to
the last LED update in its set.
Fix this by using a global lock for the pca995x device during
pca955x_led_work. Also used a struct for shared data betreen all LEDs.
[akpm@linux-foundation.org: revert unintentional rename of pca955x_ledsel()]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The leds timer trigger does not currently have an interface to activate a
one shot timer. The current support allows for setting two timers, one
for specifying how long a state to be on, and the second for how long the
state to be off. The delay_on value specifies the time period an LED
should stay in on state, followed by a delay_off value that specifies how
long the LED should stay in off state. The on and off cycle repeats until
the trigger gets deactivated. There is no provision for one time
activation to implement features that require an on or off state to be
held just once and then stay in the original state forever.
Without one shot timer interface, user space can still use timer trigger
to set a timer to hold a state, however when user space application
crashes or goes away without deactivating the timer, the hardware will be
left in that state permanently.
As a specific example of this use-case, let's look at vibrate feature on
phones. Vibrate function on phones is implemented using PWM pins on SoC
or PMIC. There is a need to activate one shot timer to control the
vibrate feature, to prevent user space crashes leaving the phone in
vibrate mode permanently causing the battery to drain.
This trigger exports three properties, activate, state, and duration When
transient trigger is activated these properties are set to default values.
- duration allows setting timer value in msecs. The initial value is 0.
- activate allows activating and deactivating the timer specified by
duration as needed. The initial and default value is 0. This will allow
duration to be set after trigger activation.
- state allows user to specify a transient state to be held for the specified
duration.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: NeilBrown <neilb@suse.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A halted kernel should not show a heartbeat.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For better code readability, ALS code is moved to new a function -
lm3530_als_configure()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change existing timer trigger to use the new ->activated flag to set
activate successful status in activate routine and check it in deactivate
routine to do cleanup.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change existing triggers backlight, gpio, and heartbeat to use the new
->activated flag to set activate successful status in their activate
routines and check it in their deactivate routines to do cleanup.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The advantage of kcalloc is that will prevent integer overflows which
could result from the multiplication of number of elements and size and it
is also a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
led-class.c and ledtrig-timer.c still use simple_strtoul(). Change them
to use kstrtoul() instead of obsolete simple_strtoul().
Also fix the existing int ret declaration to be ssize_t to match the
return type for _store functions in ledtrig-timer.c.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gcc 4.6.2 complains that:
drivers/leds/leds-lp5521.c: In function `lp5521_load_program':
drivers/leds/leds-lp5521.c:214:21: warning: `mode' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5521.c: In function `lp5521_probe':
drivers/leds/leds-lp5521.c:788:5: warning: `buf' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5521.c:740:6: warning: `ret' may be used uninitialized in this function [-Wuninitialized]
These are real problems if lp5521_read() returns an error. When that
happens we should handle it, instead of ignoring it or doing a bitwise
OR with all the other error codes and continuing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Milo <Milo.Kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__devexit functions are discarded without CONFIG_HOTPLUG, so they need
to be referenced carefully. A __devexit function may also not be called
from a __devinit function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 892a884 (leds: convert led platform drivers to module_platform_driver)
is omitting the section mismatch error: so change annotation of the probe
function to __devinit instead of __init.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=onDl
-----END PGP SIGNATURE-----
Merge tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
After moving some core functions to led-core.c, led-class.c can be built
as module again.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve the readability by moving the code setting gen_config to one
place.
[akpm@linux-foundation.org: fix some patch skew]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: "Milo(Woogyom) Kim" <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Peter Meerwald <p.meerwald@bct-electronic.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use 'pdata' rather than 'pltfm' in lm3530_init_registers().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LM3530_ALS_ZONE_REG is read-only register.
Writing this register is not necessary.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* add 'struct lm3530_pwm_data' in the platform data
The pwm data is the platform specific functions which generate the pwm.
The pwm data is only valid when brightness is pwm input mode.
Functions should be implemented by the pwm driver.
pwm_set_intensity() : set duty of pwm.
pwm_get_intensity() : get current the brightness.
* brightness control by pwm
If the control mode is pwm, then brightness is changed by the duty of
pwm=. So pwm platform function should be called in lm3530_brightness_set().
* do not update brightness register when pwm input mode
In pwm input mode, brightness register is not used.
If any value is updated in this register, then the led will be off.
* when input mode is changed, set duty of pwm to 0 if unnecessary.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To get members of lm3530_data, use 'struct led_classdev' rather than
'struct i2c_client'.
[akpm@linux-foundation.org: fix 80-column fixes more nicely]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only 7 bits are used for updating the brightness. (register address :
A0h) So the max_brightness property of lm3530 should be set to 127.
On initializing registers, maximum initial brightness is limited to
'max_brightness'.
Division-by-two is removed on updating the brightness. This arithmetic is
not necessary because the range of brightness is 0 ~ 127= .
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
