This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.
As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.
Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.
Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.
Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. This patch adds the ADC driver which is
based on the MFD for the same SoCs ADC.
This also registers the thermal adc channel in the iio map array so
iio_hwmon could use it without modifying the Device Tree. This registers
the driver in the thermal framework.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, this driver is capable of not registering the thermal sensor in
the thermal framework and thus, "quicken" the ADC readings.
This driver probes on three different platform_device_id to take into
account slight differences (registers bit and temperature computation)
between Allwinner SoCs ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are a few more little cleanups that could be done on this driver, but
I don't think any are sufficient to justify not moving it out of staging.
It's a very simple driver (presumably for a simple part) so not much that can
go wrong. I think it was only ever in staging because that's where IIO was
as a whole at the time and then we forgot about it!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are some unanswered questions due to disagreements between the code
and various datasheets (including between different datasheets for the same
part).
I don't think that is necessarily a reason to keep it in staging however.
I'm partly posting this patch inorder to reignite debate and with a bit
of luck find someone who has one of these to test!
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the SAR (Successive Approximation Register) ADC
on the Amlogic Meson SoCs.
The code is based on the public S805 (Meson8b) and S905 (GXBB)
datasheets (see [0] and [1]), as well as by reading (various versions
of) the vendor driver and by inspecting the registers on the vendor
kernels of my testing-hardware.
Currently the GXBB, GXL and GXM SoCs are supported. GXBB hardware has
10-bit ADC resolution, while GXL and GXM have 12-bit ADC resolution.
The code was written to support older SoCs (Meson8 and Meson8b) as well,
but due to lack of actual testing-hardware no of_device_id was added for
these.
Two "features" from the vendor driver are currently missing:
- the vendor driver uses channel #7 for calibration (this improves the
accuracy of the results - in my tests the results were less than 3%
off without calibration compared to the vendor driver). Adding support
for this should be easy, but is not required for most applications.
- channel #6 is connected to the SoCs internal temperature sensor.
Adding support for this is probably not so easy since (based on the
u-boot sources) most SoC versions are using different registers and
algorithms for the conversion from "ADC value" to temperature.
Supported by the hardware but currently not supported by the driver:
- reading multiple channels at the same time (the hardware has a FIFO
buffer which stores multiple results)
- continuous sampling (this would require a way to enable this
individually because otherwise the ADC would be drawing power
constantly)
- interrupt support (similar to the vendor driver this new driver is
polling the results. It is unclear if the IRQ-mode is supported on
older (Meson6 or Meson8) hardware as well or if there are any errata)
[0]
http://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
[1] http://dn.odroid.com/S905/DataSheet/S905_Public_Datasheet_V1.1.4.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add IIO driver for the Renesas RCar GyroADC block. This block is a
simple 4/8-channel ADC which samples 12/15/24 bits of data every
cycle from all channels.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds TI's tlc4541 16-bit ADC driver. Which is a single channel
ADC. Supports raw and trigger buffer access.
Also supports the tlc3541 14-bit device, which has not been tested.
Implementation of the tlc3541 is fairly straight forward thou.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is the IIO driver for AVIA HX711 ADC which is mostly used in weighting
cells.
The protocol is quite simple and using GPIOs:
One GPIO is used as clock (SCK) while another GPIO is read (DOUT)
The raw value read from the chip is delivered.
To get a weight one needs to subtract the zero offset and scale it.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds a new driver for the TI ADS7950 family of ADC chips. These
communicate using SPI and come in 8/10/12-bit and 4/8/12/16 channel
varieties.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicroelectronics STM32 MCU's analog to
digital converter.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add core driver for STMicroelectronics STM32 ADC (Analog to Digital
Converter). STM32 ADC can be composed of up to 3 ADCs with shared
resources like clock prescaler, common interrupt line and analog
reference voltage.
This core driver basically manages shared resources.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DAC is used to find the peak level of an alternating voltage input
signal by a binary search using the output of a comparator wired to
an interrupt pin. Like so:
_
| \
input +------>-------|+ \
| \
.-------. | }---.
| | | / |
| dac|-->--|- / |
| | |_/ |
| | |
| | |
| irq|------<-------'
| |
'-------'
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the AD7766, AD7766-1, AD7766-2, AD7767, AD7767-1, AD7767-2
Analog to Digital converters. It's a family of single channel 24-bit SAR
ADCs. They are all digital interface compatible and the main difference is
the internal decimation rate and analog performance. For communication with
the host processor a SPI interface is used.
In addition the part has a data ready pin that is pulsed for one MCLK cycle
when a conversion has completed and can be used as a IIO trigger.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7766.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD7767.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Apex Embedded Systems STX104 features 16 channels of single-ended (8
channels of true differential) 16-bit analog input. Differential input
configuration may be selected via a physical jumper on the device.
Similarly, input polarity (unipolar/bipolar) is configured via a
physical jumper on the device.
Input gain selection is available to the user via software, thus
allowing eight possible input ranges: +-10V, +-5V, +-2.5V, +-1.25V,
0 to 10V, 0 to 5V, 0 to 2.5V, and 0 to 1.25V. Four input gain
configurations are supported: x1, x2, x4, and x8.
This ADC resolution is 16-bits (1/65536 of full scale). Analog input
samples are taken on software trigger; neither FIFO sampling nor
interrupt triggering is supported by this driver.
The Apex Embedded Systems STX104 is primarily an analog-to-digital
converter device. The STX104 IIO driver was initially placed in the DAC
directory because only the DAC portion of the STX104 was supported at
the time. Now that ADC support has been added to the STX104 IIO driver,
the driver should be moved to the more appropriate ADC directory.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds Texas Instruments' ADC12130/ADC12132/ADC12138 12-bit plus
sign ADC driver. I have tested with the ADC12138. The ADC12130 and
ADC12132 are not tested but these are similar to ADC12138 except that
the mode programming instruction is a bit different.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds basic support for the LTC2485 ADC - a delta-sigma analog-to-digital
converter with an I2C interface that operates in single shot conversion
mode.
The driver supports an on board 5V reference and the power-on default
configuration which rejects both 50hz & 60hz line frequencies and
operates in 1x speed mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Texas Instruments ADC141S626, and ADC161S626 chips.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=SgQo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.7 cycle.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Add base support for the 10-bit SAR ADC peripheral found
on NXP LPC18xx/43xx SoCs.
This is a minimal driver that does not support burst mode,
interrupts, DMA or hardware triggers.
User manual with register description can be found on:
LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf
LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver has sysfs readings with runtime PM support for power saving.
It also offers buffer support that can be used together with IIO software
triggers.
Datasheet can be found here:
http://www.ti.com.cn/cn/lit/ds/symlink/ads1015.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is a conversion queue driver for the mx25 SoC. It uses the central
ADC which is used by two seperate independent queues. This driver
prepares different conversion configurations for each possible input.
For a conversion it creates a conversionqueue of one item with the
correct configuration for the chosen channel. It then executes the queue
once and disables the conversion queue afterwards.
The reference voltages are configurable through devicetree subnodes,
depending on the connections of the ADC inputs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832. The remaining ADC0834 and
ADC0838 are very similar to ADC0832.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver supports the new version of the Atmel ADC device introduced
with the SAMA5D2 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Freescale i.MX7D soc contains a new ADC IP. This patch add this ADC
driver support, and the driver only support ADC software trigger.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
in SOFTWARE buffer mode, a kthread will capture the active scan_elements
into a kfifo, then compute the remaining time until the next capture tick
and do an active wait (udelay).
This will produce a stream of up to fours channels plus a 64bits
timestamps (ns).
Tested with ina226, on BeagleBoneBlack.
Datasheet: http://www.ti.com/lit/gpn/ina226
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Texas Intruments ADS8688 ADC.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Martin Hundebøll <martin.hundeboll@prevas.dk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver code was found as:
aaabb2e045/drivers/staging/iio/adc
Fixed various compilation issues and test this driver on omap5 evm.
Signed-off-by: Pradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move the entry for the CC 10001 ADC driver in Kconfig and Makefile up to
maintain alphabetic order.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the support of the Berlin ADC, available on Berlin SoCs.
This ADC has 8 channels available, with one connected to a temperature
sensor.
The particularity here, is that the temperature sensor connected to the
ADC has its own registers, and both the ADC and the temperature sensor
must be configured when using it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for DA9150 Charger & Fuel-Gauge IC GPADC.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The voltage ADC is peripheral of Qualcomm SPMI PMIC chips. It has
15bits resolution and register space inside PMIC accessible across
SPMI bus.
The vadc driver registers itself through IIO interface.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good thing,
but not at a huge rate this release, only about 70k lines removed
overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid details.
The "contentious" thing here is the movement of the Android binder code
out of staging into the "real" part of the kernel. This is code that
has been stable for a few years now and is working as-is in the tens of
millions of devices with no issues. Yes, the code is horrid, and the
userspace api leaves a lot to be desired, but it's not going to change
due to legacy issues that we have no control over. Because so many
devices and companies rely on this, and the code is stable, might as
well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been doing
it for the past few years with no problems. I'll send a MAINTAINERS
entry for it before 3.19-final is out, still need to talk to the Google
developers about if they are willing to help with it or not, last I
checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSPICkACgkQMUfUDdst+yksdwCfSLE9VUy1o2sAPDRe+J3bQced
EWEAoL3RtnejKbo5tHS2IT69pLrwiIDS
=YXyM
-----END PGP SIGNATURE-----
Merge tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
16 bits resolution and register space inside PMIC accessible across
SPMI bus.
The driver registers itself through IIO interface.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Platform driver for X-Powers AXP288 ADC, which is a sub-device of the
customized AXP288 PMIC for Intel Baytrail-CR platforms. GPADC device
enumerates as one of the MFD cell devices. It uses IIO infrastructure
to communicate with userspace and consumer drivers.
Usages of ADC channels include battery charging and thermal sensors.
Based on initial work by:
Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ADC is a 3-channel signal-ended 10-bit Successive Approximation
Register (SAR) A/D Converter. It uses the supply and ground as its reference
and converts the analog input signal into 10-bit binary digital codes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for ADC128S052 from TI.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
