This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device counting could be controlled by the level or the edges of
a trigger.
in_count0_enable_mode attibute allow to set the control mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
One of the features of STM32 trigger hardware block is a quadrature
encoder that can counts up/down depending of the levels and edges
of the selected external pins.
This patch allow to read/write the counter, get it direction,
set/get quadrature modes and get scale factor.
When counting up preset value is the limit of the counter.
When counting down the counter start from preset value down to 0.
This preset value could be set/get by using
/sys/bus/iio/devices/iio:deviceX/in_count0_preset attribute.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In order to accommodate in a logical manner for the premuxed channels
in PM8921 and the similarly addressed channels in later PMICs, we
need a twocell arrangement with premux and analog mux setting as
a tuple to uniquely identify a hardware channel.
These bindings are not yet in use, so it should be fine to augment
them before we actually start using it in drivers and device trees.
This scheme came out of lengthy discussions and reverse-engineering
and reading of the few information sources we have.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh+dt@kernel.org>
Suggested-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add documentation for max9611 driver.
Document attributes describing value of shunt resistor installed between
RS+ and RS- voltage sense inputs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add device tree bindings documentation for Maxim max9611/max9612 current
sense amplifier.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
-----BEGIN PGP SIGNATURE-----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=YYdq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Third set of new device support, cleanups and features for IIO in the 4.12 cycle
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mpu9250 is a SIP containing an mpu6500 and an ak8975. If this was all
there was too it there would be no need for explicit handling in the driver.
Arguably the bindings would also only reflect the presence of an mpu6500 with
the ak8975 hanging off it, as the kernel doesn't care that they are in one
package.
However, the WHOAMI value changes as well so best to add explicit support.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These bindings are somewhat lagging the state of the driver. The i2c-gate
bindings are documented elsewhere, but it seems sensible to at least have
an example and cross reference in here. SPI bindings will need to be the
subject of a future patch.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
The rk3328 saradc is the same as rk3399.
Signed-off-by: Liang Chen <cl@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Rick Altherr <raltherr@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.
Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.
Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A smattering of different small fixes for some random driver subsystems.
Nothing all that major, just resolutions for reported issues and bugs.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNedPQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykY+wCeL0dFw/ney0sJ6s7HsmXu3uxFGyoAoIIXL7AP
48YAht+BOOmBzagXIKbw
=EFxm
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"A smattering of different small fixes for some random driver
subsystems. Nothing all that major, just resolutions for reported
issues and bugs.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
extcon: int3496: Set the id pin to direction-input if necessary
extcon: int3496: Use gpiod_get instead of gpiod_get_index
extcon: int3496: Add dependency on X86 as it's Intel specific
extcon: int3496: Add GPIO ACPI mapping table
extcon: int3496: Rename GPIO pins in accordance with binding
vmw_vmci: handle the return value from pci_alloc_irq_vectors correctly
ppdev: fix registering same device name
parport: fix attempt to write duplicate procfiles
auxdisplay: img-ascii-lcd: add missing sentinel entry in img_ascii_lcd_matches
Drivers: hv: vmbus: Don't leak memory when a channel is rescinded
Drivers: hv: vmbus: Don't leak channel ids
Drivers: hv: util: don't forget to init host_ts.lock
Drivers: hv: util: move waiting for release to hv_utils_transport itself
vmbus: remove hv_event_tasklet_disable/enable
vmbus: use rcu for per-cpu channel list
mei: don't wait for os version message reply
mei: fix deadlock on mei reset
intel_th: pci: Add Gemini Lake support
intel_th: pci: Add Denverton SOC support
intel_th: Don't leak module refcount on failure to activate
...
Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of good
fixes from Johan for devices with crazy descriptors. There are a few
new device ids in here as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWNefwQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykewwCg1P1HEZV2wLJSalsPxduIKIRLcmkAnRcE0H31
2egrp1seSGQumYcGQUJ/
=2fH+
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.11-rc4.
Nothing major here, just an bunch of small fixes, and a handfull of
good fixes from Johan for devices with crazy descriptors. There are a
few new device ids in here as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: gadget: f_hid: fix: Don't access hidg->req without spinlock held
usb: gadget: udc: remove pointer dereference after free
usb: gadget: f_uvc: Sanity check wMaxPacketSize for SuperSpeed
usb: gadget: f_uvc: Fix SuperSpeed companion descriptor's wBytesPerInterval
usb: gadget: acm: fix endianness in notifications
usb: dwc3: gadget: delay unmap of bounced requests
USB: serial: qcserial: add Dell DW5811e
usb: hub: Fix crash after failure to read BOS descriptor
ACM gadget: fix endianness in notifications
USB: usbtmc: fix probe error path
USB: usbtmc: add missing endpoint sanity check
USB: serial: option: add Quectel UC15, UC20, EC21, and EC25 modems
usb: musb: fix possible spinlock deadlock
usb: musb: dsps: fix iounmap in error and exit paths
usb: musb: cppi41: don't check early-TX-interrupt for Isoch transfer
usb-core: Add LINEAR_FRAME_INTR_BINTERVAL USB quirk
uwb: i1480-dfu: fix NULL-deref at probe
uwb: hwa-rc: fix NULL-deref at probe
USB: wusbcore: fix NULL-deref at probe
USB: uss720: fix NULL-deref at probe
...
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to:
Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4CFb
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc fixes from Michael Ellerman:
"These are all pretty minor. The fix for idle wakeup would be a bad bug
but has not been observed in practice.
The update to the gcc-plugins docs was Cc'ed to Kees and Jon, Kees
OK'ed it going via powerpc and I didn't hear from Jon.
- cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
- powerpc/64s: Fix idle wakeup potential to clobber registers
- Revert "powerpc/64: Disable use of radix under a hypervisor"
- gcc-plugins: update architecture list in documentation
Thanks to: Andrew Donnellan, Nicholas Piggin, Paul Mackerras, Vaibhav
Jain"
* tag 'powerpc-4.11-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
gcc-plugins: update architecture list in documentation
Revert "powerpc/64: Disable use of radix under a hypervisor"
powerpc/64s: Fix idle wakeup potential to clobber registers
cxl: Route eeh events to all slices for pci_channel_io_perm_failure state
one where we need to copy a string because we can't guarantee it isn't
freed sometime later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=8q6a
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of Sunxi and Rockchip clk driver fixes and a core framework
one where we need to copy a string because we can't guarantee it isn't
freed sometime later"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: rockchip: Make uartpll a child of the gpll on rk3036
clk: rockchip: add "," to mux_pll_src_apll_dpll_gpll_usb480m_p on rk3036
clk: core: Copy connection id
dt-bindings: arm: update Armada CP110 system controller binding
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
This patch adds support for STMicro VL6180 - ALS, range and proximity sensor. Sensor is capable of measuring the light
intensity as well as object distance using TOF (Time of Flight) technology.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Fix initialization of HS400-ES eMMC cards
- A couple of fixes for the mmc block device driver
- Resolved a compiler warning
MMC host:
- sdhci: Do not disable IRQs while waiting for clock
- sdhci-pci: Do not disable IRQs in sdhci_intel_set_power
- sdhci-of-arasan: Fix incorrect timeout clock
- mediatek: Fix bug for setting wrong clock frequency
- sdhci-of-at91: Use regulator to fix cmd timeout errors
- ushc: Fix NULL-deref at probe
- rockchip-dw-mshc: Rename RK1108 to RV1108 in DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJY1OMSAAoJEP4mhCVzWIwpKyIQAIUGeulfz50/3w8tHrn1o2SP
WAGQ0wtum5LVw7EUNMQL6WbNca0tclTucv9KFj4v7uMc1cOsWvbkUt9N1OZE4Xgl
nd/zeOQZUT03R+VFouHqNAt67+V6mQ53NNNp2E6D4MXI1FmNJCpcfU30Pl3rJ6uH
h8H61j4kA6a4eMKyJ12lJlIuoxV7VN8TS1TCe4iiu2ZSiaqtH+Q98Li6TvsvOcRo
kM72Bs8UBBEpMFqrUaGN8mo+cfCc+ByPOWVc+fvmkiyKGrfz2ivrQLDR5QkT38yU
AgdfptQgMuKtwc5lthnM1kxSsixUgROCuWTECWWSHPl5W29frFfI6QvBFjBGFqbR
ckL9ZMtpKfRuph1m9COODZneYDH3PULKIQpmUjwBLsh6FAQfvzkppPFvDhLTz+xi
jP5+iqKjUkrAc7i5doSNrdwjMQZR5GSo+c1KlqfiK2QXdf/ay/rSP/IpotHjKgbl
xUTe5dk7rs0WyT/T6Hd4lXGCEPb0mRO8ExulkOE8pEO78Sb+UBn1pPokLqPvp4zz
Ct8pFARBGqEX2DMOyV6qqDBr1qbbyMW8L3yymqI3iL2Inu8AaFkqefQvOg1M40MB
Qx8US2RN8jeRNg8KGQdRO6p53X/RYy3qdEAAkj42Mv5OvEvwtcIHlBfwRhTkGd4t
PTaxnc8pdfT8QyuwTSvP
=AB+h
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull mmc fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.11 rc4.
MMC core:
- Fix initialization of HS400-ES eMMC cards
- A couple of fixes for the mmc block device driver
- Resolved a compiler warning
MMC host:
- sdhci: Do not disable IRQs while waiting for clock
- sdhci-pci: Do not disable IRQs in sdhci_intel_set_power
- sdhci-of-arasan: Fix incorrect timeout clock
- mediatek: Fix bug for setting wrong clock frequency
- sdhci-of-at91: Use regulator to fix cmd timeout errors
- ushc: Fix NULL-deref at probe
- rockchip-dw-mshc: Rename RK1108 to RV1108 in DT"
* tag 'mmc-v4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci: Do not disable interrupts in sdhci_intel_set_power
mmc: sdhci: Do not disable interrupts while waiting for clock
mmc: ushc: fix NULL-deref at probe
mmc: sdhci-of-at91: Support external regulators
mmc: core: mmc_blk_rw_cmd_err - remove unused variable
mmc: mediatek: Fixed bug where clock frequency could be set wrong
mmc: block: Fix cmd error reset failure path
mmc: block: Fix is_waiting_last_req set incorrectly
mmc: core: Fix access to HS400-ES devices
mmc: sdhci-of-arasan: fix incorrect timeout clock
dt-bindings: rockchip-dw-mshc: rename RK1108 to RV1108
Just several fixups,
- fix page fault and vblank timeout issues due to delayed vblank handling.
- fix panel driver probing to fail without te-gpios property.
- fix potential security hole by using "%pK" format.
- fix wrong if statement condition.
And one cleanup which removes Exynos4415 SoC support which is not supported
anymore.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/dsi: make te-gpios optional
drm/exynos: Print kernel pointers in a restricted form
drm/exynos/decon5433: fix software trigger mask
drm/exynos/fimd: signal frame done interrupt at front porch
drm/exynos/decon5433: signal frame done interrupt at front porch
drm/exynos/decon5433: fix vblank event handling
drm/exynos: move crtc event handling to drivers callbacks
drm/exynos: Remove support for Exynos4415 (SoC not supported anymore)
drm/exynos/decon5433: & vs | typo
f_acm got an endianness fix by Oliver Neukum. This has been around for a
long time but it's finally fixed.
f_hid learned that it should never access hidg->req without first
grabbing the spinlock.
Roger Quadros fixed two bugs in the f_uvc function driver.
Janusz Dziedzic fixed a very peculiar bug with EP0, one that's rather
difficult to trigger. When we're dealing with bounced EP0 requests, we
should delay unmap until after ->complete() is called.
UDC class got a use-after-free fix.
-----BEGIN PGP SIGNATURE-----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=BWuW
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.11-rc4
f_acm got an endianness fix by Oliver Neukum. This has been around for a
long time but it's finally fixed.
f_hid learned that it should never access hidg->req without first
grabbing the spinlock.
Roger Quadros fixed two bugs in the f_uvc function driver.
Janusz Dziedzic fixed a very peculiar bug with EP0, one that's rather
difficult to trigger. When we're dealing with bounced EP0 requests, we
should delay unmap until after ->complete() is called.
UDC class got a use-after-free fix.
*) Revert USB3 PHY support for Broadcom NSP SoC
*) Fix compiler error on qcom-usb-hs when depends on EXTCON
is not added
*) Fix error handling in phy-exynos-pcie
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=AZDi
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.11-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.11-rc
*) Revert USB3 PHY support for Broadcom NSP SoC
*) Fix compiler error on qcom-usb-hs when depends on EXTCON
is not added
*) Fix error handling in phy-exynos-pcie
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add support for Linear Technology LTC2632 (SPI) family of·
dual 12- 10-, and 8-bits output DACs.
Signed-off-by: Maxime Roussin-Belanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 65c059bcaa ("powerpc: Enable support for GCC plugins") enabled GCC
plugins on powerpc, but neglected to update the architecture list in the
docs. Rectify this.
Fixes: 65c059bcaa ("powerpc: Enable support for GCC plugins")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It wasn't clear if the 'forwarding' setting needs to be enabled on the
interface that packets are received from, or on the interface that
packets are forwarded to, or both.
In fact (according to my code reading) the setting is relevant on the
interface that packets are received from, so this change updates the doc
to say that.
Signed-off-by: Neil Jerram <neil@tigera.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull irq fixes from Thomas Gleixner:
- a workaround for a GIC erratum
- a missing stub function for CONFIG_IRQDOMAIN=n
- fixes for a couple of type inconsistencies
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Fix incorrect type of register size
irqchip/gicv3-its: Add workaround for QDF2400 ITS erratum 0065
irqdomain: Add empty irq_domain_check_msi_remap
irqchip/crossbar: Fix incorrect type of local variables
ARM updates from Marc Zyngier:
"vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with
many PCIe devices
General bug fixes:
- Gracefully handle exception generated with syndroms that
the host doesn't understand
- Properly invalidate TLBs on VHE systems"
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU reset
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYxENfAAoJEED/6hsPKofoEEkIAIWglnOGOHqf4pPv9OThKzKm
5CGINdPVEkJ56QNaYrINiQRHAzIUg8dsrhsisYmEdYGv3Mxf5WO0OebfzTrniNm4
GXIM8OuYD04MSnIomfGGBAwFZ6ptgdeD+PVkSFYHArkvWYfPm54ghjVj3AXmkicf
tRiIsPSiL/QT0vha5LBGfwsWOYavmZRfQBNA5yYUIHgO0Mp7LI24AeZOQiSM2ngx
Gl5xfzk0bayhZSBr+r/fvxqbEd0udiY7klGEvt3hrPT+JzzpoamEgCCZ6eLFZbGM
eABeQUzm7StD4Ib3WHkVU81ysOWndL0TK94BBBLIn1j+ht9FLi9iGkmTYspk9po=
=/phS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM updates from Marc Zyngier:
- vgic updates:
- Honour disabling the ITS
- Don't deadlock when deactivating own interrupts via MMIO
- Correctly expose the lact of IRQ/FIQ bypass on GICv3
- I/O virtualization:
- Make KVM_CAP_NR_MEMSLOTS big enough for large guests with many
PCIe devices
- General bug fixes:
- Gracefully handle exception generated with syndroms that the host
doesn't understand
- Properly invalidate TLBs on VHE systems
x86:
- improvements in emulation of VMCLEAR, VMX MSR bitmaps, and VCPU
reset
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: do not warn when MSR bitmap address is not backed
KVM: arm64: Increase number of user memslots to 512
KVM: arm/arm64: Remove KVM_PRIVATE_MEM_SLOTS definition that are unused
KVM: arm/arm64: Enable KVM_CAP_NR_MEMSLOTS on arm/arm64
KVM: Add documentation for KVM_CAP_NR_MEMSLOTS
KVM: arm/arm64: VGIC: Fix command handling while ITS being disabled
arm64: KVM: Survive unknown traps from guests
arm: KVM: Survive unknown traps from guests
KVM: arm/arm64: Let vcpu thread modify its own active state
KVM: nVMX: reset nested_run_pending if the vCPU is going to be reset
kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
KVM: arm/arm64: vgic-v3: Don't pretend to support IRQ/FIQ bypass
arm64: KVM: VHE: Clear HCR_TGE when invalidating guest TLBs
Here is a number of different USB fixes for 4.11-rc2. Seems like there
were a lot of unresolved issues that people have been finding for this
subsystem, and a bunch of good security auditing happening as well from
Johan Hovold. There's the usual batch of gadget driver fixes and xhci
issues resolved as well.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWMOkLA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymiCACeIL3h4bNEc6+XLiB+sfmQx4wV2MUAnRMD1gB0
GxkBXY1Iny94vhZC8x5r
=dlkm
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of different USB fixes for 4.11-rc2.
Seems like there were a lot of unresolved issues that people have been
finding for this subsystem, and a bunch of good security auditing
happening as well from Johan Hovold. There's the usual batch of gadget
driver fixes and xhci issues resolved as well.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: host: xhci-plat: Fix timeout on removal of hot pluggable xhci controllers
usb: host: xhci-dbg: HCIVERSION should be a binary number
usb: xhci: remove dummy extra_priv_size for size of xhci_hcd struct
usb: xhci-mtk: check hcc_params after adding primary hcd
USB: serial: digi_acceleport: fix OOB-event processing
MAINTAINERS: usb251xb: remove reference inexistent file
doc: dt-bindings: usb251xb: mark reg as required
usb: usb251xb: dt: add unit suffix to oc-delay and power-on-time
usb: usb251xb: remove max_{power,current}_{sp,bp} properties
usb-storage: Add ignore-residue quirk for Initio INIC-3619
USB: iowarrior: fix NULL-deref in write
USB: iowarrior: fix NULL-deref at probe
usb: phy: isp1301: Add OF device ID table
usb: ohci-at91: Do not drop unhandled USB suspend control requests
USB: serial: safe_serial: fix information leak in completion handler
USB: serial: io_ti: fix information leak in completion handler
USB: serial: omninet: drop open callback
USB: serial: omninet: fix reference leaks at open
USB: serial: io_ti: fix NULL-deref in interrupt callback
usb: dwc3: gadget: make to increment req->remaining in all cases
...
Merge fixes from Andrew Morton:
"26 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
userfaultfd: remove wrong comment from userfaultfd_ctx_get()
fat: fix using uninitialized fields of fat_inode/fsinfo_inode
sh: cayman: IDE support fix
kasan: fix races in quarantine_remove_cache()
kasan: resched in quarantine_remove_cache()
mm: do not call mem_cgroup_free() from within mem_cgroup_alloc()
thp: fix another corner case of munlock() vs. THPs
rmap: fix NULL-pointer dereference on THP munlocking
mm/memblock.c: fix memblock_next_valid_pfn()
userfaultfd: selftest: vm: allow to build in vm/ directory
userfaultfd: non-cooperative: userfaultfd_remove revalidate vma in MADV_DONTNEED
userfaultfd: non-cooperative: fix fork fctx->new memleak
mm/cgroup: avoid panic when init with low memory
drivers/md/bcache/util.h: remove duplicate inclusion of blkdev.h
mm/vmstats: add thp_split_pud event for clarity
include/linux/fs.h: fix unsigned enum warning with gcc-4.2
userfaultfd: non-cooperative: release all ctx in dup_userfaultfd_complete
userfaultfd: non-cooperative: robustness check
userfaultfd: non-cooperative: rollback userfaultfd_exit
x86, mm: unify exit paths in gup_pte_range()
...
Patch series "userfaultfd non-cooperative further update for 4.11 merge
window".
Unfortunately I noticed one relevant bug in userfaultfd_exit while doing
more testing. I've been doing testing before and this was also tested
by kbuild bot and exercised by the selftest, but this bug never
reproduced before.
I dropped userfaultfd_exit as result. I dropped it because of
implementation difficulty in receiving signals in __mmput and because I
think -ENOSPC as result from the background UFFDIO_COPY should be enough
already.
Before I decided to remove userfaultfd_exit, I noticed userfaultfd_exit
wasn't exercised by the selftest and when I tried to exercise it, after
moving it to a more correct place in __mmput where it would make more
sense and where the vma list is stable, it resulted in the
event_wait_completion in D state. So then I added the second patch to
be sure even if we call userfaultfd_event_wait_completion too late
during task exit(), we won't risk to generate tasks in D state. The
same check exists in handle_userfault() for the same reason, except it
makes a difference there, while here is just a robustness check and it's
run under WARN_ON_ONCE.
While looking at the userfaultfd_event_wait_completion() function I
looked back at its callers too while at it and I think it's not ok to
stop executing dup_fctx on the fcs list because we relay on
userfaultfd_event_wait_completion to execute
userfaultfd_ctx_put(fctx->orig) which is paired against
userfaultfd_ctx_get(fctx->orig) in dup_userfault just before
list_add(fcs). This change only takes care of fctx->orig but this area
also needs further review looking for similar problems in fctx->new.
The only patch that is urgent is the first because it's an use after
free during a SMP race condition that affects all processes if
CONFIG_USERFAULTFD=y. Very hard to reproduce though and probably
impossible without SLUB poisoning enabled.
This patch (of 3):
I once reproduced this oops with the userfaultfd selftest, it's not
easily reproducible and it requires SLUB poisoning to reproduce.
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 2 PID: 18421 Comm: userfaultfd Tainted: G ------------ T 3.10.0+ #15
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
task: ffff8801f83b9440 ti: ffff8801f833c000 task.ti: ffff8801f833c000
RIP: 0010:[<ffffffff81451299>] [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP: 0018:ffff8801f833fe80 EFLAGS: 00010202
RAX: ffff8801f833ffd8 RBX: 6b6b6b6b6b6b6b6b RCX: ffff8801f83b9440
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800baf18600
RBP: ffff8801f833fee8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: ffffffff8127ceb3 R12: 0000000000000000
R13: ffff8800baf186b0 R14: ffff8801f83b99f8 R15: 00007faed746c700
FS: 0000000000000000(0000) GS:ffff88023fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007faf0966f028 CR3: 0000000001bc6000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
do_exit+0x297/0xd10
SyS_exit+0x17/0x20
tracesys+0xdd/0xe2
Code: 00 00 66 66 66 66 90 55 48 89 e5 41 54 53 48 83 ec 58 48 8b 1f 48 85 db 75 11 eb 73 66 0f 1f 44 00 00 48 8b 5b 10 48 85 db 74 64 <4c> 8b a3 b8 00 00 00 4d 85 e4 74 eb 41 f6 84 24 2c 01 00 00 80
RIP [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP <ffff8801f833fe80>
---[ end trace 9fecd6dcb442846a ]---
In the debugger I located the "mm" pointer in the stack and walking
mm->mmap->vm_next through the end shows the vma->vm_next list is fully
consistent and it is null terminated list as expected. So this has to
be an SMP race condition where userfaultfd_exit was running while the
vma list was being modified by another CPU.
When userfaultfd_exit() run one of the ->vm_next pointers pointed to
SLAB_POISON (RBX is the vma pointer and is 0x6b6b..).
The reason is that it's not running in __mmput but while there are still
other threads running and it's not holding the mmap_sem (it can't as it
has to wait the even to be received by the manager). So this is an use
after free that was happening for all processes.
One more implementation problem aside from the race condition:
userfaultfd_exit has really to check a flag in mm->flags before walking
the vma or it's going to slowdown the exit() path for regular tasks.
One more implementation problem: at that point signals can't be
delivered so it would also create a task in D state if the manager
doesn't read the event.
The major design issue: it overall looks superfluous as the manager can
check for -ENOSPC in the background transfer:
if (mmget_not_zero(ctx->mm)) {
[..]
} else {
return -ENOSPC;
}
It's safer to roll it back and re-introduce it later if at all.
[rppt@linux.vnet.ibm.com: documentation fixup after removal of UFFD_EVENT_EXIT]
Link: http://lkml.kernel.org/r/1488345437-4364-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/20170224181957.19736-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
overide||override
While we are here, fix the doubled "address" in the touched line
Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt.
Also, fix the comment block style in the touched hunks in
drivers/media/dvb-frontends/drx39xyj/drx_driver.h.
Link: http://lkml.kernel.org/r/1481573103-11329-21-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Three fixes for intel_pstate problems related to the passive
mode (in which it acts as a regular cpufreq scaling driver), two
for the handling of global P-state limits and one for the handling
of the cpu_frequency tracepoint in that mode (Rafael Wysocki).
- Three fixes for the handling of P-state limits in intel_pstate in
the active mode (Rafael Wysocki).
- Introduction of a new cpufreq.off=1 kernel command line argument
that will disable cpufreq entirely if passed to the kernel and
is simply hooked up to the existing code used by Xen (Len Brown).
- Fix for the schedutil cpufreq governor to prevent it from using
stale raw frequency values in configurations with mutiple CPUs
sharing one policy object and a cleanup for it reducing its
overhead slightly (Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gwp7
-----END PGP SIGNATURE-----
Merge tag 'pm-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix several issues in the intel_pstate driver and one issue in
the schedutil cpufreq governor, clean up that governor a bit and hook
up existing code for disabling cpufreq to a new kernel command line
option.
Specifics:
- Three fixes for intel_pstate problems related to the passive mode
(in which it acts as a regular cpufreq scaling driver), two for the
handling of global P-state limits and one for the handling of the
cpu_frequency tracepoint in that mode (Rafael Wysocki).
- Three fixes for the handling of P-state limits in intel_pstate in
the active mode (Rafael Wysocki).
- Introduction of a new cpufreq.off=1 kernel command line argument
that will disable cpufreq entirely if passed to the kernel and is
simply hooked up to the existing code used by Xen (Len Brown).
- Fix for the schedutil cpufreq governor to prevent it from using
stale raw frequency values in configurations with mutiple CPUs
sharing one policy object and a cleanup for it reducing its
overhead slightly (Viresh Kumar)"
* tag 'pm-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Do not reinit performance limits in ->setpolicy
cpufreq: intel_pstate: Fix intel_pstate_verify_policy()
cpufreq: intel_pstate: Fix global settings in active mode
cpufreq: Add the "cpufreq.off=1" cmdline option
cpufreq: schedutil: Pass sg_policy to get_next_freq()
cpufreq: schedutil: move cached_raw_freq to struct sugov_policy
cpufreq: intel_pstate: Avoid triggering cpu_frequency tracepoint unnecessarily
cpufreq: intel_pstate: Fix intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Do not use performance_limits in passive mode
* pm-cpufreq:
cpufreq: intel_pstate: Do not reinit performance limits in ->setpolicy
cpufreq: intel_pstate: Fix intel_pstate_verify_policy()
cpufreq: intel_pstate: Fix global settings in active mode
cpufreq: Add the "cpufreq.off=1" cmdline option
cpufreq: intel_pstate: Avoid triggering cpu_frequency tracepoint unnecessarily
cpufreq: intel_pstate: Fix intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Do not use performance_limits in passive mode
This reverts commit c8ca631f94 ("dt-bindings: phy: Add documentation
for NSP USB3 PHY") to match reverting commit adding the new PHY driver.
Please note we revert this commit before it reached stable release.
If new compatible string is needed it should be added to the existing
bcm-ns-usb3-phy.txt which already describes this PHY.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Mark the reg property as required and furthermore fix some typos and
spellings in the documentation.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename oc-delay-* to oc-delay-us and make it expect a time value.
Furthermore add -ms suffix to power-on-time. There changes were
suggested by Rob Herring in https://lkml.org/lkml/2017/2/15/1283.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the max_{power,current}_{sp,bp} properties of the usb251xb driver
from devicetree. This is done to simplify the dt bindings as requested
by Rob Herring in https://lkml.org/lkml/2017/2/15/1283. If those
properties are ever needed by somebody they can be enabled again easily.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull perf fixes from Ingo Molnar:
"This includes a fix for a crash if certain special addresses are
kprobed, plus does a rename of two Kconfig variables that were a minor
misnomer"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Rename CONFIG_[UK]PROBE_EVENT to CONFIG_[UK]PROBE_EVENTS
kprobes/x86: Fix kernel panic when certain exception-handling addresses are probed
This patch adds documentation for a new "phy-handle" property,
"fixed-link" and "mdio" sub-node. These allows the enumeration
of PHYs which are supported by the phy library under drivers/net/phy.
The EMAC ethernet controller in IBM and AMCC 4xx chips is
currently stuck with a few privately defined phy
implementations. It has no support for PHYs which
are supported by the generic phylib.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
window. Namely powerpc broke as jump labels uses the two LSB bits as flags
in initialization. A check was added to make sure that all jump label
entries were 4 bytes aligned, but powerpc didn't work that way for modules.
Adding an alignment in the module linker script appeared to be the best
solution.
Jump labels also added an anonymous union to access those LSB bits as a
normal long. But because this structure had static initialization, it broke
older compilers that could not statically initialize anonymous unions
without brackets.
The command line parameter for setting function graph filter broke the
"EMPTY_HASH" descriptor by modifying it instead of creating a new hash to
hold the entries.
The command line parameter ftrace_graph_max_depth was added to allow its
setting at boot time. It uses existing code and only the command line hook
was added. This is not really a fix, but as it uses existing code without
affecting anything else, I added it to this release. It was ready before the
merge window closed, but I wanted to let it sit in linux-next for a couple
of days first.
-----BEGIN PGP SIGNATURE-----
iQExBAABCAAbBQJYvNrAFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
JGQIAMkayeZ0OCyYHRPR4EcCrdE3fATmt1huJWHrMPnT4/fLabL8XQqrOpnOBMq1
GFZb1SMkBmvGtAHF4GbvCxnIUfDQko6BTQAd8EMea1WM8+Kb66/BLgJawjWIU9I0
dNYre9ONgR2NOzkz6nfKRXnmy0lRcOweBb09YYGSzY11Md7d8T3T4TUrPNZdYrO9
8ZMbF4qRd9KLMRHcsWqvhWhBISxWnmtUSlthfweukKgDMy8OKpb7pR0ckjtYwsWX
RF41jqLqzSUqtd/nE2Sj/aT8XOP4pfrKEUuNM4SBj8q5jmNcZuqi8Q9wItu3LWR2
jqM/9UKTzaCr9cchwuvUC0i+jWc=
=kDql
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"There was some breakage with the changes for jump labels in the 4.11
merge window:
- powerpc broke as jump labels uses the two LSB bits as flags in
initialization.
A check was added to make sure that all jump label entries were 4
bytes aligned, but powerpc didn't work that way for modules. Adding
an alignment in the module linker script appeared to be the best
solution.
- Jump labels also added an anonymous union to access those LSB bits
as a normal long. But because this structure had static
initialization, it broke older compilers that could not statically
initialize anonymous unions without brackets.
- The command line parameter for setting function graph filter broke
the "EMPTY_HASH" descriptor by modifying it instead of creating a
new hash to hold the entries.
- The command line parameter ftrace_graph_max_depth was added to
allow its setting at boot time. It uses existing code and only the
command line hook was added.
This is not really a fix, but as it uses existing code without
affecting anything else, I added it to this release. It was ready
before the merge window closed, but I wanted to let it sit in
linux-next for a couple of days first"
* tag 'trace-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/graph: Add ftrace_graph_max_depth kernel parameter
tracing: Add #undef to fix compile error
jump_label: Add comment about initialization order for anonymous unions
jump_label: Fix anonymous union initialization
module: set __jump_table alignment to 8
ftrace/graph: Do not modify the EMPTY_HASH for the function_graph filter
tracing: Fix code comment for ftrace_ops_get_func()
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
