Now that we are using components in omapdss, there's no need for
separate handling of dss and dispc driver init. Thus we can move the dss
and dispc init and unit func pointers to the lists we use for the other
dss submodules.
We can now also handle errors returned by the registration functions
properly: if registering a driver fails, we can stop processing and
return the error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.
This patch solves the mess by using the component system for DSS
submodules.
The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.
The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.
However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We have a list of function pointers to dss submodule uninit functions.
It makes sense to do the uninit in the reverse order to init, but that
is not currently the case.
This patch reorders the uninit calls to be the reverse of init order.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The following patches will add component handling to omapdss, improving
the handling of deferred probing. However, at the moment we're using
quite a lot of __inits and __exits in the driver, which prevent normal
dynamic probing and removal.
This patch removes most of the uses of __init and __exit, so that we can
register drivers after module init, and so that we can unregister
drivers even if the module is built-in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The return value of dss_init_ports() is not handled at all, causing
crashes later if the call failed.
This patch adds the error handling, and we also move the call to a
slightly earlier place to make bailing out easier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Refactor dss probe function by extracting the setup for video plls into
a separate function. The call to this function is also moved to a
slightly earlier phase, so that in error case we can bail out more
easily.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We have a flag, 'dss_initialized', which tells omapfb and omapdrm if
omapdss is available. At the moment it can be set even if the dss
submodules are not all ready, in case something gets deferred.
Move the flag to dss_core driver so that it'll signal the availability
of the dss drivers move accurately.
For now, it'll signal that dss_core is ready, which is not quite correct
but still better than previously. The following patches will add
component system to omapdss, and after those patches 'dss_initialized'
will signal that all the submodules are ready.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Since kobject_init_and_add takes a format string, make sure that the
passed in name cannot be accidentally parsed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is a constraint in the OMAP4 HDMI IP that requires to use
the 8-channel code when transmitting more than two channels.
The constraint doesn't apply for OMAP5 so don't force the channel
allocation in the sound driver as it can be done specifically for
OMAP4 later in the hdmi4 core.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Downmix inhibit in HDMI_CORE_FC_AUDICONF3 register is in
bit 4 while CEA861_AUDIO_INFOFRAME_DB5_DM_INH sets bit 7.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As per TRM, HDMI_WP_AUDIO_CFG[2] LEFT_BEFORE = 0 is reserved,
so it must always be set to 1 (the first sample is the left).
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4 HDMI IP uses the 8-channel layout with 8-channel speaker
allocation mask when transmitting more than two channels. But
the channel count field (CC) of the Audio InfoFrame's DB1 is
not updated for 8-channels.
As per HDMI Compliance Test 7.31 "Audio InfoFrame", CC = 7 is
required for 8-channels CA masks (0x13 and 0x1F).
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also make use of gpiod_get*_optional where applicable.
Apart from simplification of the affected drivers this is another step
towards making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add handling of missed events in omap_dss_pm_notif which are
needed to support hibernation (suspend to disk).
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't need VT switch when suspending/resuming, so disable it. This
speeds up suspend/resume.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: NeilBrown <neil@brown.name>
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU9Vn9AAoJEFDCiBxwnmDriPMP/2Bzx7kYdRkTFICqGsITHcUf
pjMEf7htHdg+lFn6jBYtLW42NqZMX+kI1BIpd6RzEjKxAhbp0tr7FVwn0Kds2rQw
6ikwtZsd6oBR61Xv0sZWMwNbfn2MUcl7M9k+Sh6kDUBph5IEMZ5F+n8dRYHhA+MH
rs9PGTH2DmRE1HXvWBjsE8QVgfia4WRp5OipDkOxNhCpkbzU4XqbVoBh/6BmJ54R
Dxq3srM479CyRY3o4+KT4ajhS7g4aU7WTQMxIXtU0cLcYMvfkcHoYwNBw+bjSn3s
eYfjpw96XHhS4abVzo8QziN1oNV/i/Y4wpqIOKwY5TnA+Gt+sEnFXjGHa331QdpL
WdisAQg/6MFPlR4D7gkBWEjoeeMn4FkyiFSHntYclywOxv/Cbc/l1cOyPkS3zxIa
v6KH7zu5J83sICx8TlZv0YLnES1GtixCuWukaKzyLiAXqHVGullkBvUauQwRrtEW
73CjIGpCTQMY5xmt/8V8JFi1HQLbDBRlHkX2WOzcrByLLgiGaUeKRvjYcYtaBm7q
Q25E10lnW3cGf+kljlPfc3NVxgtQUGaQKsx+wzICnz6h+0gdEzsTcAWB3Qp891jX
q+RSqEsT93oSAhPxJYQGvEu4wPfmOrh7QvProwj8mR1Jp6TyvgGi9pOtHU+YwOz+
EZD+c6mhdOfuWgD8GqT/
=jtB3
-----END PGP SIGNATURE-----
Merge tag 'of-graph-for-4.0' of git://git.pengutronix.de/git/pza/linux into for-next
Pull of-graph helpers from Philipp Zabel:
of: Add of-graph helpers to loop over endpoints and find ports by id
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
It was found that having two displays enabled and having an NV12 overlay
on one of the displays will cause underflows/synclosts. Debugging this
pointed to some issue with MFLAG.
It is unclear why this issue is happening, but it looks like there is a
HW bug related to MFLAG and FIFO management. Disabling MFLAG makes this
issue go away, but then we lose the benefit of MFLAG. Also forcing MFLAG
always on makes the issue go away.
Also, using certain values for MFLAG_START, MFLAG thresholds and PRELOAD
makes the issue go away, but there was no obvious logic to which values
work and which don't.
As a workaround until more information about this is found, force MFLAG
always on to make NV12 usable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 has support for MFLAG feature, which allows DSS to dynamically
increase the priority of DISPC's DMA traffic. At the moment we don't
have support for it.
It was noticed that on DRA7 with high bandwidth use cases we see FIFO
underflows. Implementing MFLAG support removed those underflows.
Interestingly, on OMAP5 uEVM no such overflows were seen.
This patch adds a simple MFLAG implementation, where we use a fixed
MFLAG threshold value based on the FIFO size. The thresholds are set to
4/8 of fifo size for low threshold, and 5/8 of fifo size for high
threshold.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we don't setup FIFO thresholds by default in omapdss. It's
supposed to be done by the user of omapdss. And that is missing from
omapdrm, causing unoptimal thresholds to be used when using omapdrm.
While I believe it's in theory better to allow the user of omapdss to
setup the fifo thresholds, in practice we always use the same values,
and we could as well setup the thresholds in omapdss.
Furthermore, in omapdss init we always swap the FIFO used for GFX and WB
overlays, but we don't swap the FIFO thresholds for those overlays
(which is the reason for omapdrm using unoptimal HW reset values). So
it would make sense to setup the thresholds to account for the swapping
of the FIFOs.
So, this patch adds code to setup default FIFO tresholds at omapdss
init.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dispc driver presumes that the callers handle locking for all normal
functions. However, omapdrm doesn't handle this, and presumes that all
overlay manager registers are private to that overlay manager, and thus
presumes that configurations for overlay managers can be written via
different threads freely.
For many registers the above is true. The exceptions are DISPC_CONTROL
and DISPC_CONFIG registers, which contain bits for both LCD and TV
overlay managers.
Fixing this properly in omapdrm means a big omapdrm rewrite. So, for
now, add locking to dispc for the problematic registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Somnath Mukherjee <somnath@ti.com>
omapdrm doesn't always configure the overlays correctly, causing the
overlay setup functions to be called with zero timings. This leads to
division by zero error.
This happens, for example, when a HDMI cable is not connected, but a
user tries to setup a plane with scaling.
Fixing omapdrm is a big job, so for now let's check for the bad timings
in DISPC and return an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The common 'struct videomode' does not have a flag to select when the
sync signals should be driven.
The default behavior of DISPC HW is to drive the sync signal on the
opposite pixel clock edge from data signal, which is also what the
videomode_to_omap_video_timings() uses.
However, it looks like what panels usually expect is that the data and
sync signals are driven on the same edge, so let's change
videomode_to_omap_video_timings() to set the sync_pclk_edge accordingly.
Note that this only affect panels drivers that use
videomode_to_omap_video_timings(), probably when getting the video
timings directly from DT data. The drivers can still configure the
sync_pclk_edge independently if they so wish.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When configuring the lcd timings, instead of writing enum values
directly to the HW, use switch-case to get the value to be programmed.
This is safer and also allows us to change the enum values.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC can drive data lines either on rising or falling pixel clock edge,
which can be configured by the user.
Sync lines can also be driven on rising or falling pixel clock edge, but
additionally the HW can be configured to drive the sync lines on
opposite clock edge from the data lines.
This opposite edge setting does not make any sense, as the same effect
can be achieved by just setting the sync lines to be driven on the other
edge compared to the data lines. It feels like some kind of backward
compatibility option, even if all DSS versions seem to have the same
implementation.
To simplify the code and configuration of the signals, and to make the
dispc timings more compatible with what is used on other platforms,
let's just remove the whole opposite-edge support.
The drivers that used OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES setting are
changed so that they use the opposite setting from the data edge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TFP410 requires that DE is active high and the data and syncs are driven
on rising pixel clock edge. However, at the moment the driver doesn't
request such syncs, and the end result is that the sync settings depend
on default values, which are not right in all cases.
Set the sync values explicitly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC driver checks that the buffer address is not 0. However, when
using TILER, the address space is TILER specific and 0 is a valid
address.
Fix the check to allow address of 0 for TILER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: srinivas pulukuru <srinivas.pulukuru@ti.com>
omapdss's sysfs directories for displays used to have 'name' file,
giving the name for the display. This file was later renamed to
'display_name' to avoid conflicts with i2c sysfs 'name' file. Looks like
at least xserver-xorg-video-omap3 requires the 'name' file to be
present.
To fix the regression, this patch creates new kobjects for each display,
allowing us to create sysfs directories for the displays. This way we
have the whole directory for omapdss, and there will be no sysfs file
clashes with the underlying display device's sysfs files.
We can thus add the 'name' sysfs file back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
It has been observed that the current SDA-HOLD time is too short for
some board/cable/monitor combinations. Increase the SDA-HOLD time to
1000ns.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
AM43xx supports pixel clock divider of 1, just like all OMAP3+ SoCs. Fix
the minimum divider value.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Decrementing the reference count of the previous endpoint node allows to
use the of_graph_get_next_endpoint function in a for_each_... style macro.
All current users of this function that pass a non-NULL prev parameter
(that is, soc_camera and imx-drm) are changed to not decrement the passed
prev argument's refcount themselves.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
the check of the return code is missing, user space does not get notified
about the error condition:
omapdss OVERLAY error: overlay 2 horizontally not inside the display area (403 + 800 >= 800)
omapdss APPLY error: failed to apply settings: illegal configuration.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx DPI output.
DRA7xx has three DPI outputs, each of which gets its input from a DISPC
channel. However, DRA72x has only one video PLL, and DRA74x has two
video PLLs. In both cases the video PLLs need to be shared between
multiple outputs. The driver doesn't handle this at the moment.
Also, DRA7xx requires configuring CONTROL module bits to route the clock
from the PLL to the used DISPC channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx to the HDMI driver.
The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.
This patch adds support to write the polarities to control module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A race issue has been observed with the encoder-tpd12s015 driver, which
leads to errors when trying to read EDID. This has only now been
observed, as OMAP4 and OMAP5 boards used SoC's GPIOs for LS_OE GPIO. On
dra7-evm boards, the LS_OE is behind a i2c controlled GPIO expander,
which increases the time to set the LS_OE.
This patch simplifies the handling of the LS_OE gpio in the driver by
removing the interrupt handling totally. The only time we actually need
to enable LS_OE is when we are reading the EDID, and thus we can just
set and clear the LS_OE gpio inside the read_edid() function.
This also has the additional benefit of very slightly decreasing the
power consumption.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.
Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Assigning ddata->invert_polarity to itself is not very useful; the
context suggests that the right-hand side should have been
pdata->invert_polarity.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
opa362 is amplifier for video and can be connected to the tvout pads
of the OMAP3. It has one gpio control for enable/disable of the output
(high impedance).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After the commit ef691ff48b (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.
Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The regulator_disable() doesn't accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI hardware parameters structs for OMAP4 and OMAP5 contained two
initializers for 'clkdco_max'. The first one was a remnant with wrong
value.
Remove the extra initializer entries.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
