Now that we have infoframes to report the pixel repeat flag, we can
start using it. Fixes locking the 720x480i and 720x576i modes on my
Dell 2408WFP. Like the 1920x1080i case, they don't fit properly on
the screen, though.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes a purple bar on the left side of the screen with my Dell
2408WFP. It will also be required for supporting the double-clocked
video modes.
Signed-off-by: Eric Anholt <eric@anholt.net>
We really do need to be using the halved V fields. I had been
confused by the code I was using as a reference because it stored
halved vsync fields but not halved vdisplay, so it looked like I only
needed to divide vdisplay by 2.
This reverts part of Mario's timestamping fixes that prevented
CRTC_HALVE_V from applying, and instead adjusts the timestamping code
to not use the crtc field in that case.
Fixes locking of 1920x1080x60i on my Dell 2408WFP. There are black
bars on the top and bottom, but I suspect that might be an
under/overscan flags problem as opposed to video timings.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes occasional debug spew at boot when connected directly through
HDMI, and probably confusing the HDMI state machine when we go trying
to poke registers for the enable sequence too soon.
Signed-off-by: Eric Anholt <eric@anholt.net>
On Pi0/1/2, we use an external GPIO line for hotplug detection, since
the HDMI_HOTPLUG register isn't connected to anything. However, with
the Pi3 the HPD GPIO line has moved off to a GPIO expander that will
be tricky to get to (the firmware is constantly polling the expander
using i2c0, so we'll need to coordinate with it).
As a stop-gap, if we don't have a GPIO line, use an EDID probe to
detect connection. Fixes HDMI display on the pi3.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes broken grayscale ramps on many HDMI monitors, where large areas
at the ends of the ramp would all appear as black or white.
Signed-off-by: Eric Anholt <eric@anholt.net>
With the introduction of bin/render pipelining, the previous job may
not be completed when we start binning the next one. If the previous
job wrote our VBO, IB, or CS textures, then the binning stage might
get stale or uninitialized results.
Fixes the major rendering failure in glmark2 -b terrain.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: ca26d28bba ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Cc: stable@vger.kernel.org
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX6H4uAAoJEHm+PkMAQRiG5sMH/3yzrMiUCSokdS+cvY+jgKAG
JS58JmRvBPz2mRaU3MRPBGRDeCz/Nc9LggL2ZcgM+E1ZYirlYyQfIED3lkqk5R07
kIN1wmb+kQhXyU4IY3fEX7joqyKC6zOy4DUChPkBQU0/0+VUmdVmcJvsuPlnMZtf
g95m0BdYTui+eDezASRqOEp3Lb5ONL4c3ao4yBP0LHF033ctj3VJQiyi5uERPZJ0
5e6Mo7Wxn78t9WqJLQAiEH46kTwT2plNlxf3XXqTenfIdbWhqE873HPGeSMa3VQV
VywXTpCpSPQsA8BYg66qIbebdKOhs9MOviHVfqDtwQlvwhjlBDya0gNHfI5fSy4=
=Y/L5
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rc8' into drm-next
Linux 4.8-rc8
There was a lot of fallout in the imx/amdgpu/i915 drivers, so backmerge
it now to avoid troubles.
* tag 'v4.8-rc8': (1442 commits)
Linux 4.8-rc8
fault_in_multipages_readable() throws set-but-unused error
mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing
radix tree: fix sibling entry handling in radix_tree_descend()
radix tree test suite: Test radix_tree_replace_slot() for multiorder entries
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
mm: delete unnecessary and unsafe init_tlb_ubc()
huge tmpfs: fix Committed_AS leak
shmem: fix tmpfs to handle the huge= option properly
blk-mq: skip unmapped queues in blk_mq_alloc_request_hctx
MIPS: Fix pre-r6 emulation FPU initialisation
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
nvme-rdma: only clear queue flags after successful connect
i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
perf/core: Limit matching exclusive events to one PMU
...
There are many reasons other than ENOMEM that drm_dev_init() can
fail. Return ERR_PTR rather than NULL to be able to distinguish
these in the caller.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160921145919.13754-2-teg@jklm.no
We get 1 warning when building kernel with W=1:
drivers/gpu/drm/vc4/vc4_bo.c:147:6: warning: no previous prototype for 'vc4_bo_cache_purge' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
So this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The intent was to make sure people don't sneak in a small immediate or
something to change the interpretation of the uniform update args, but
these signals are just fine.
Fixes a validation failure in the current X server on some Render
operation.
Signed-off-by: Eric Anholt <eric@anholt.net>
Drivers may set the NO_DISABLE_AFTER_MODESET flag in the 'flags' parameter
of the helper drm_atomic_helper_commit_planes() if the relevant display
controllers(e.g., IPUv3 for imx-drm) require to disable a CRTC's planes
when the CRTC is disabled. The helper would skip the ->atomic_disable
call for a plane if the CRTC of the old plane state needs a modesetting
operation. Of course, the drivers need to disable the planes in their CRTC
disable callbacks since no one else would do that.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1472461923-14364-1-git-send-email-gnuiyl@gmail.com
This came from the initial bringup code, which always idled the GPU
and always reset the overflow. That massively increases the size of
the working set when you're doing lots of small draws, though, as is
common on X desktops or piglit.
Signed-off-by: Eric Anholt <eric@anholt.net>
We'd end up NULL pointer dereferencing because we didn't take the
error path out in the parent. Fixes igt vc4_lookup_fail test.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: d5b1a78a77 ("drm/vc4: Add support for drawing 3D frames.")
Cc: stable@vger.kernel.org
Overflow memory handling is tricky: While it's still referenced by the
BPO registers, we want to keep it from being freed. When we are
putting a new set of overflow memory in the registers, we need to
assign the old one to the last rendering job using it.
We were looking at "what's currently running in the binner", but since
the bin/render submission split, we may end up with the binner
completing and having no new job while the renderer is still
processing. So, if we don't find a bin job at all, look at the
highest-seqno (last) render job to attach our overflow to.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: ca26d28bba ("drm/vc4: improve throughput by pipelining binning and rendering jobs")
Cc: stable@vger.kernel.org
The BO cache will complain if BOs are still allocated when we try to
destroy it (since freeing those BOs would try to hit the cache). You
could hit this if you were to unload the module after a GPU hang.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 214613656b ("drm/vc4: Add an interface for capturing the GPU state after a hang.")
If the device was already up, a 1 is returned instead of 0. We were
erroring out, leading the 3D driver to sometimes fail at screen
initialization (generally with ENOENT returned to it).
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: af713795c5 ("drm/vc4: Add a getparam ioctl for getting the V3D identity regs.")
If you exceeded the size that kmalloc would return, you'd get a dmesg
warning and a return from the job submit. We can handle much
allocations with vmalloc, and drm_malloc_ab makes that decision.
Fixes failure in piglit's scissor-many.
Signed-off-by: Eric Anholt <eric@anholt.net>
If you managed to exceed the limit to switch to vmalloc, we'd use the
wrong free.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: d5b1a78a77 ("drm/vc4: Add support for drawing 3D frames.")
Cc: stable@vger.kernel.org
Add missing drm_crtc_vblank_on/off() calls so vblank irq
handling/updating/timestamping never runs with a crtc shut down
or during its shutdown/startup, as that causes large jumps in
vblank count and trouble for compositors.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On top of the interlaced video mode fix and with some additional
adjustments, this now works well. It has almost the same accuracy
as on regular progressive scan modes.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can't handle doublescan modes at the moment, so if
userspace tries to set one, reject the mode set.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We must not apply CRTC_INTERLACE_HALVE_V to interlaced modes during
mode enumeration, as drm_helper_probe_single_connector_modes
does, so wrap it and reset the effect of CRTC_INTERLACE_HALVE_V
on affected interlaced modes.
Also mode_fixup interlaced modes passed in from user space.
This fixes the vblank timestamping constants and entries in
the mode->crtc_xxx fields needed for precise vblank timestamping.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We already don't expose such modes to userspace, but make
sure userspace can't sneak some interlaced mode in.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The plane .prepare_fb() and .cleanup_fb() helpers are optional, there's
no need to implement empty stubs, and no need to explicitly set the
function pointers to NULL either.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[danvet: Resolved conflicts with Chris' patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lots of drivers don't properly compile without this when CONFIG_FB=n.
It's kinda a hack, but since CONFIG_FB doesn't stub any fucntions when
it's disabled I think it makes sense to add it to drm_fb_helper.h.
Long term we probably need to rethink all the logic to unload firmware
framebuffer drivers, at least if we want to be able to move away from
CONFIG_FB and fbcon.
v2: Unfortunately just stubbing out remove_conflicting_framebuffers in
drm_fb_helper.h upset gcc about static vs. non-static declarations, so
a new wrapper it needs to be. Means more churn :(
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: tomi.valkeinen@ti.com
Cc: dh.herrmann@gmail.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470847958-28465-2-git-send-email-daniel.vetter@ffwll.ch
Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).
Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The following functions test whether their argument is NULL
and then return immediately.
* drm_fbdev_cma_hotplug_event
* drm_fbdev_cma_restore_mode
Thus the tests around their calls are not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/fb33d930-6a5c-c501-6676-26bd486f1cb5@users.sourceforge.net
allowing GLSL shaders with non-unrolled loops.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Qh0U
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux into drm-next
This pull request brings in vc4 shader validation for branching,
allowing GLSL shaders with non-unrolled loops.
* tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux:
drm/vc4: Fix a "the the" typo in a comment.
drm/vc4: Fix definition of QPU_R_MS_REV_FLAGS
drm/vc4: Add a getparam to signal support for branches.
drm/vc4: Add support for branching in shader validation.
drm/vc4: Add a bitmap of branch targets during shader validation.
drm/vc4: Move validation's current/max ip into the validation struct.
drm/vc4: Add a getparam ioctl for getting the V3D identity regs.
We don't use it in shader validation currently, so it had no effect,
but best to fix it anyway in case we do some day.
Signed-off-by: Eric Anholt <eric@anholt.net>
Userspace needs to know if it can create shaders that do branching.
Otherwise, for backwards compatibility with old kernels it needs to
lower if statements to conditional assignments.
Signed-off-by: Eric Anholt <eric@anholt.net>
We're already checking that branch instructions are between the start
of the shader and the proper PROG_END sequence. The other thing we
need to make branching safe is to verify that the shader doesn't read
past the end of the uniforms stream.
To do that, we require that at any basic block reading uniforms have
the following instructions:
load_imm temp, <next offset within uniform stream>
add unif_addr, temp, unif
The instructions are generated by userspace, and the kernel verifies
that the load_imm is of the expected offset, and that the add adds it
to a uniform. We track which uniform in the stream that is, and at
draw call time fix up the uniform stream to have the address of the
start of the shader's uniforms at that location.
Signed-off-by: Eric Anholt <eric@anholt.net>
This isn't used yet, it's just a first step toward loop validation.
During the main parsing of instructions, we need to know when we hit a
new basic block so that we can reset validated state.
v2: Fix a stray semicolon after an if block. (caught by kbuild test).
Signed-off-by: Eric Anholt <eric@anholt.net>
vblank timestamping, and a couple of small cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJXhUULAAoJELXWKTbR/J7oZ1oQAKnTTJlnCbaSNrWbRBUuaMtO
S2RQKyMI2LOpf4XE13cNHm0IaYNOw6hJIXlnxeuzHbQSGvOrHnabluZuvAfLa3OQ
4bb8K0elWsPRbtmx2L8DjncLCmmmOsbczrTwo3efq70XZs4PyaCp2vHpCU8kI7HJ
xO/fk6E8sYDPFCxZxb82C7LTSjQBlPn58dD+cEFg1kGILOhyR1eZwRj8e4netjKU
gN/059R6VPPor+I8oIMrqoHAxAlZUGnVPsK/1rgR5cfxlC1NPKU71eI7xiBLNclt
86BcvU/LuwAYt81UirnGTQU/m47dCMK4mmpzD/9EgVW/KTUPLPubML+u9fL67+B4
BJ7T7N4t7APblqkO/iI9DcTAkZNmydq4sdsfDdXcVZ3umDTNpmb/PQuq+rFEc1CZ
qsBw13kJ4bHBYUpZvrxuCesSRLpXhUiSOg/uVnRHTdiALZqQQyzQlnw6Q4GCMKiz
R99/k4/7/cAgQkGElwLeHR8Aw0r26m+X4pnLN9lrafjQjlH04CcuvFwlak28jnit
Oi0eZ0VD9RTHwPzUIoe4M32Q/7oAe7y5b7gCNPbM/0s56WQv+cIHi7CdgdIYtUWs
BIyeBTzpLvzkEvrEMYoipgpv3scbudMssTd3bo8gsdOu0tllBzi59Poo5hl6pQbs
lseJ7LavmK5sPDPsIZb3
=aF3C
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux into drm-next
This pull request brings in new vc4 plane formats for Android, precise
vblank timestamping, and a couple of small cleanups.
* tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux:
drm/vc4: remove redundant ret status check
drm/vc4: Implement precise vblank timestamping.
drm/vc4: Bind the HVS before we bind the individual CRTCs.
gpu: drm: vc4_hdmi: add missing of_node_put after calling of_parse_phandle
drm: vc4: enable XBGR8888 and ABGR8888 pixel formats
drm/vc4: clean up error exit path on failed dpi_connector allocation
Reduces the argument count for some of the functions, and will be used
more with the upcoming looping support.
Signed-off-by: Eric Anholt <eric@anholt.net>
As I extend the driver to support different V3D revisions, userspace
needs to know what version it's targeting. This is most easily
detected using the V3D identity registers.
v2: Make sure V3D is runtime PM on when reading the registers.
v3: Switch to a 64-bit param value (suggested by Rob Clark in review)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: Rob Clark <robdclark@gmail.com> (v3, over irc)
At the current point where ret is being checked for non-zero it has
not changed since it was initialized to zero, hence the check and the
label unref are redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Precise vblank timestamping is implemented via the
usual scanout position based method. On VC4 the
pixelvalves PV do not have a scanout position
register. Only the hardware video scaler HVS has a
similar register which describes which scanline for
the output is currently composited and stored in the
HVS fifo for later consumption by the PV.
This causes a problem in that the HVS runs at a much
faster clock (system clock / audio gate) than the PV
which runs at video mode dot clock, so the unless the
fifo between HVS and PV is full, the HVS will progress
faster in its observable read line position than video
scan rate, so the HVS position reading can't be directly
translated into a scanout position for timestamp correction.
Additionally when the PV is in vblank, it doesn't consume
from the fifo, so the fifo gets full very quickly and then
the HVS stops compositing until the PV enters active scanout
and starts consuming scanlines from the fifo again, making
new space for the HVS to composite.
Therefore a simple translation of HVS read position into
elapsed time since (or to) start of active scanout does
not work, but for the most interesting cases we can still
get useful and sufficiently accurate results:
1. The PV enters active scanout of a new frame with the
fifo of the HVS completely full, and the HVS can refill
any fifo line which gets consumed and thereby freed up by
the PV during active scanout very quickly. Therefore the
PV and HVS work effectively in lock-step during active
scanout with the fifo never having more than 1 scanline
freed up by the PV before it gets refilled. The PV's
real scanout position is therefore trailing the HVS
compositing position as scanoutpos = hvspos - fifosize
and we can get the true scanoutpos as HVS readpos minus
fifo size, so precise timestamping works while in active
scanout, except for the last few scanlines of the frame,
when the HVS reaches end of frame, stops compositing and
the PV catches up and drains the fifo. This special case
would only introduce minor errors though.
2. If we are in vblank, then we can only guess something
reasonable. If called from vblank irq, we assume the irq is
usually dispatched with minimum delay, so we can take a
timestamp taken at entry into the vblank irq handler as a
baseline and then add a full vblank duration until the
guessed start of active scanout. As irq dispatch is usually
pretty low latency this works with relatively low jitter and
good results.
If we aren't called from vblank then we could be anywhere
within the vblank interval, so we return a neutral result,
simply the current system timestamp, and hope for the best.
Measurement shows the generated timestamps to be rather precise,
and at least never off more than 1 vblank duration worst-case.
Limitations: Doesn't work well yet for interlaced video modes,
therefore disabled in interlaced mode for now.
v2: Use the DISPBASE registers to determine the FIFO size (changes
by anholt)
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com> (v2)
We need to be able to look at the CRTC's registers in the HVS as part
of initialization, while the HVS doesn't need to look at the PV
registers.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
merged before 4.7rc1, plus two new fixes that have come in since then.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=52r8
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-fixes-2016-06-06' into drm-vc4-next
Merge Mario's get_vblank_counter fix forward to prevent conflicts with
his followon patch to add precise vblank timestamping.
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
DRM_FORMAT_XBGR8888 and DRM_FORMAT_ABGR8888 are 2 of the native formats
used in Android, so enable them for VC4. There seems to be no logic behind
HVS_PIXEL_ORDER_xxxx naming, but HVS_PIXEL_ORDER_ARGB seems to work
correctly.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
Somehow I didn't spot this when pushing :(
Fixes: 398e97994f ("drm/vc4: Remove open-coded drm_connector_register_all()")
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
All outputs have a 1:1 relationship between connectors and encoders and
the driver is relying on the atomic helpers: we can drop the custom
->best_encoder() implementations and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-15-git-send-email-boris.brezillon@free-electrons.com
