Since 287f3a943f ("pppoe: Use workqueue to die properly when a PADT
is received"), pppoe_disc_rcv() disconnects the socket by scheduling
pppoe_unbind_sock_work(). This is enough to stop socket transmission
and makes the PPPOX_ZOMBIE state uncessary.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operation of adding VLANs on a port via switchdev ops can fail and
we need to be prepared for it. If we do not rollback hardware operations
following a failure, hardware and software will remain in an
inconsistent state.
Solve that by adding suitable error paths to __mlxsw_sp_port_vlans_add.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding or deleting VLANs from a bridged port, HW VLAN filters must be
set accordingly. Instead of having the same code in both add and delete
functions, just wrap it in a function and call it with the appropriate
parameters.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a range of VLANs in which PVID is a member we should use
the correct PVID value instead of some VLAN in the range.
Also, change two print statements to use 'dev' instead of
'mlxsw_sp_port->dev', as it's already used in other print statements in
the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When encx24j600 is open and closed many times due to userspace polling the
interface, the log gets noise with this log message.
Moving this to encx24j600_spi_probe function where it belongs.
Signed-off-by: Jon Ringle <jringle@gridpoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Busy polling can now be handled in generic NAPI poll infrastructure.
This removes complexity and fast path overhead :
mlx4 used two spin_lock()/spin_unlock() pair per napi->poll() call
in mlx4_en_cq_lock_napi()/mlx4_en_cq_unlock_napi()
Tested:
Without busy polling :
lpaa23:~# echo 0 >/proc/sys/net/core/busy_read
lpaa24:~# echo 0 >/proc/sys/net/core/busy_read
lpaa23:~# ./netperf -H lpaa24 -t TCP_RR
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpaa24.prod.google.com () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 47330.78
With busy polling :
lpaa23:~# echo 70 >/proc/sys/net/core/busy_read
lpaa24:~# echo 70 >/proc/sys/net/core/busy_read
lpaa23:~# ./netperf -H lpaa24 -t TCP_RR
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to lpaa24.prod.google.com () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 97643.55
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NAPI poll handler should return number of RX packets processed,
instead of 0 / budget.
This allows proper busy poll accounting through LINUX_MIB_BUSYPOLLRXPACKETS
SNMP counter.
napi_complete_done() allows /sys/class/net/ethX/gro_flush_timeout
to be used for finer GRO aggregation control.
Tested:
Enabled busy polling, and checked TcpExtBusyPollRxPackets counter is increasing.
echo 70 >/proc/sys/net/core/busy_read
nstat >/dev/null
netperf -H target -t TCP_RR >/dev/null
nstat | grep TcpExtBusyPollRxPackets
TcpExtBusyPollRxPackets 490958 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is now easy to add busy polling support to a NAPI driver,
with very little impact on normal input path.
This patch serves as a reference implementation.
Note:
A followup patch will add proper napi_complete_done() in mlx5,
so that LINUX_MIB_BUSYPOLLRXPACKETS snmp counter is properly handled.
Tested:
Normal TCP_RR results without busy polling :
lpk51:~# echo 0 >/proc/sys/net/core/busy_read
lpk52:~# echo 0 >/proc/sys/net/core/busy_read
lpk51:~# ./netperf -H 192.168.4.52 -t TCP_RR -l 10
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.4.52 () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 53509.49
16384 87380
Now enable busy polling :
lpk51:~# echo 70 >/proc/sys/net/core/busy_read
lpk52:~# echo 70 >/proc/sys/net/core/busy_read
lpk51:~# ./netperf -H 192.168.4.52 -t TCP_RR -l 10
MIGRATED TCP REQUEST/RESPONSE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.4.52 () port 0 AF_INET : first burst 0
Local /Remote
Socket Size Request Resp. Elapsed Trans.
Send Recv Size Size Time Rate
bytes Bytes bytes bytes secs. per sec
16384 87380 1 1 10.00 97530.92
16384 87380
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_low_latency_recv() is called with BH disabled,
as other ndo_busy_poll() methods.
No need for spin_lock_bh()/spin_unlock_bh()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lancer_cmd_get_file_len() uses lancer_cmd_read_object() to get
the current size of registers for ethtool registers dump. Returned status
value is stored but not checked. The check itself is not necessary as
the data_read output variable is initialized to 0 and status variable
can be removed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with the mv88e6xxx code, use the register defines to
access all the register addresses and bit fields.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.
Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err variable wasn't set with the correct error value in some cases.
Fixes: 47605df953 ('mlx4: Modify proxy/tunnel QP mechanism [..]')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cleaning slave's counter resources, we hold a spinlock that
protects the slave's counters list. As part of the clean, we call
__mlx4_clear_if_stat which calls mlx4_alloc_cmd_mailbox which is a
sleepable function.
In order to fix this issue, hold the spinlock, and copy all counter
indices into a temporary array, and release the spinlock. Afterwards,
iterate over this array and free every counter. Repeat this scenario
until the original list is empty (a new counter might have been added
while releasing the counters from the temporary array).
Fixes: b72ca7e96a ("net/mlx4_core: Reset counters data when freed")
Reported-by: Moni Shoua <monis@mellanox.com>
Tested-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On xmit path we use skb_frag_dma_map() which is using dma_map_page(),
while upon completion we dma-unmap the skb fragments using
dma_unmap_single() rather than dma_unmap_page().
To fix this, we now save the dma map type on xmit path and use this
info to call the right dma unmap method upon TX completion.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On change mtu the driver compares between hardware queried mtu and
software requested mtu. We need to compare between software
representation of the queried mtu and the requested mtu.
Fixes: facc9699f0 ('net/mlx5e: Fix HW MTU settings')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent outgoing multicast frames from looping back to the RX queue.
By introducing new HW capability self_lb_en_modifiable, which indicates
the support to modify self_lb_en bit in modify_tir command.
When this capability is set we can prevent TIRs from sending back
loopback multicast traffic to their own RQs, by "refreshing TIRs" with
modify_tir command, on every time new channels (SQs/RQs) are created at
device open.
This is needed since TIRs are static and only allocated once on driver
load, and the loopback decision is under their responsibility.
Fixes issues of the kind:
"IPv6: eth2: IPv6 duplicate address fe80::e61d:2dff:fe5c:f2e9 detected!"
The issue is seen since the IPv6 solicitations multicast messages are
loopedback and the network stack thinks they are coming from another host.
Fixes: 5c50368f38 ("net/mlx5e: Light-weight netdev open/stop")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e_get_inline_hdr_size didn't take into account the vlan insertion
into the inline WQE segment.
This could lead to max inline violation in cases where
skb_headlen(skb) + VLAN_HLEN >= sq->max_inline.
Fixes: 3ea4891db8 ("net/mlx5e: Fix LSO vlan insertion")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device probe fails, driver remains bound to the PCI device. However,
driver data has been reset to NULL. This causes crash upon dereferencing
it in nicvf_remove()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
