Without that fix connector-analog-tv driver isn't probed when compiled
as module.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits
from 4 to 1. The bit 4 is 'reserved', so this probably should not cause
any issues, but it's better to fix it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.
Fix the register dump.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb disables all the overlays when freeing resources, but it should
also remove those overlays from overlay managers.
Not doing so causes a crash if omapfb is unbound and bound, or omapfb
module is removed and loaded, while keeping omapdss around.
Fix this by calling unset_manager() for all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb is shutting down, it will disable all the overlays. However,
instead of actually disabling all the overlays, it disables only all the
overlays that are currently attached to framebuffers.
On OMAP4+, this leaves the fourth overlay left enabled.
Fix the loop so that we actually go through all the overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should wait for any pending updates when an overlay manager is
about to be disabled, because the updates will never be finished if the
manager is disabled too early.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we leave __exit annotation, driver can't be unbound
through sysfs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.
Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
without MODULE_ALIAS(), omapfb won't get loaded
automatically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove unnecessary mach/cpu.h header to be able to converge to a multiplatform
kernel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
* new 6x10 font
* various small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUPlVtAAoJEPo9qoy8lh71kCQP/RvzQ2/7H7N/P6HsCZvBAwvM
02bp8Wx679MGhzcngv6wGVeUwcE4MyhjIbOFim4ZDduti68N4Q+eIpsqPIeef+JU
emcXe9qpcsviS41kTuRc555M9wBBHeSYB7qLubHcsUprez/UTXZZBrWbXkLBn9oD
JfP/n82NLOQdjflSrfYciPy3q4x8o3h7uycUxDwrEHI77XsitVCe/M7yJifSOmxn
LiBgn983N5YQJdM2Dorgi0cFnKCNlpUVraYlbDAiHokaGNevUowCnTp2EkwwzRpQ
QAycfaI7iTd4WniP9x4GBMieHPDoqxoqD397WnvdGCh5VBBZXVRLkQnePPSC7s1l
yK6V3UBJB6AmnM4Jxd00aC2dfTjCS6NbaS5yoav0YuH6l7HE/rXgu1APXakV40jh
vwKhy+3P/Bu47gPfuXB8LlQAZ/3oQ7dlCAH0P84waHJSlYE72RqYXH4Hr4kLQnDG
a+TYYJwFl6mkieiPFEMs+5UlOhyZJ/yQKJHp0Q0ROF0zv86kJQh3P4ozfV8V9Vq7
cDn1RHa6/5e4BKVe0NGCuKAxgpF2InFZKqS81QmtRCSIrs9kjNPTXBMci2XZw9qn
UnRvKSrUdtIxlaBKGam+lhOGGN/pzVFJbGfoDBh1SsknwHdrlHzZ1J1rwWJu7a/3
7p+9ferk4UPFNu+UUhNB
=f13d
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- new 6x10 font
- various small fixes and cleanups
* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
fonts: Add 6x10 font
videomode: provide dummy inline functions for !CONFIG_OF
video/atmel_lcdfb: Introduce regulator support
fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
framebuffer: fix screen corruption when copying
framebuffer: fix border color
arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
video: fbdev: use %*ph specifier to dump small buffers
video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
video: fbdev: au1200fb: delete double assignment
video: fbdev: sis: delete double assignment
...
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This adds regulator support to enable/disable the LCD voltage, using
'lcd-supply' as regulator name.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the PM domain containing the HDMI hardware block is powered down,
the HDMI register values (incl. interrupt polarity settings) are lost.
During resume, after powering up the PM domain, interrupts are
re-enabled, and an interrupt storm happens due to incorrect interrupt
polarity settings:
irq 163: nobody cared (try booting with the "irqpoll" option)
...
Disabling IRQ #163
To fix this, re-initialize the interrupt polarity settings, and the
htop1 register block (if present), during resume.
As the .suspend_noirq() and .resume_noirq() callbacks are not called
when using the generic PM domain, the normal .resume() callback is used,
and the device interrupt needs to be disabled/enabled manually.
This fixes resume from s2ram with power down of the A4MP PM domain on
r8a7740/Armadillo.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function bitcpy_rev has a bug that may result in screen corruption.
The bug happens under these conditions:
* the end of the destination area of a copy operation is aligned on a long
word boundary
* the end of the source area is not aligned on a long word boundary
* we are copying more than one long word
In this case, the variable shift is non-zero and the variable first is
zero. The statements FB_WRITEL(comp(d0, FB_READL(dst), first), dst) reads
the last long word of the destination and writes it back unchanged
(because first is zero). Correctly, we should write the variable d0 to the
last word of the destination in this case.
This patch fixes the bug by introducing and extra test if first is zero.
The patch also removes the references to fb_memmove in the code that is
commented out because fb_memmove was removed from framebuffer subsystem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
The DT-based panel capabilities selection was picking up
a subset of available modes based on hardware configuration.
This was wrong, as the capabilities describe available
memory models and adapt the display controller to them
that the RGB output is wired up correctly (as in: R and
B components are not swapped).
This patch fixes it by removing the unnecessary limitation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of dereference each byte let's use %*ph specifier in the printk()
calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 7edaa761ee ("video: mx3fb: Add backlight control support")
changed the mx3fb driver so it always selects the BACKLIGHT_CLASS_DEVICE
symbol, but that is hidden behind BACKLIGHT_LCD_SUPPORT in Kconfig, so
we get a Kconfig warning for multi_v5_defconfig, which doesn't have that:
Warning: (DRM_RADEON && DRM_NOUVEAU && DRM_I915 && DRM_GMA500 &&
DRM_SHMOBILE && DRM_TILCDC && FB_BACKLIGHT && FB_MX3 && USB_APPLEDISPLAY
&& FB_OLPC_DCON && ASUS_LAPTOP && SONY_LAPTOP && THINKPAD_ACPI &&
EEEPC_LAPTOP && ACPI_CMPC && SAMSUNG_Q10) selects BACKLIGHT_CLASS_DEVICE
which has unmet direct dependencies (HAS_IOMEM && BACKLIGHT_LCD_SUPPORT)
This makes sure we always enable both symbols together for mx3fb, like
we do for the other drivers that can't be built without backlight
support. Note that a better solution would be to ensure the driver can
work with or without backlight support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
