Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
grp->grp_id is obsolete. It has no use in the current driver.
Remove it from gfar_priv_grp and put the 'rstat' member
in its place, in the 2nd cache line, as rstat needs fast access.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On fec_probe the clocks are enabled in the following order:
clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp
, so in the error and remove paths we should disabled them in the opposite
order.
Also fix the order in the suspend/resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 38ae92d "fec: Add support for reading
RMON registers" causes the imx6Q to crash.
This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 4c09eed9 (net: fec: Enable imx6 enet checksum acceleration) and
baa70a5c (net: fec: enable pause frame to improve rx prefomance for 1G
network) introduced functionality into the FEC driver which is not
supported on MCF5272. The registers used to implement this functionality
do not exist on MCF5272. Since register defines for MCF5272 are separate
from register defines for other chips, building images for MCF5272 fails
as follows.
fec_main.c: In function 'fec_restart':
fec_main.c:520:8: error: 'FEC_RACC' undeclared (first use in this function)
fec_main.c:585:3: error: 'FEC_R_FIFO_RSEM' undeclared (first use in this function)
fec_main.c:586:3: error: 'FEC_R_FIFO_RSFL' undeclared (first use in this function)
fec_main.c:587:3: error: 'FEC_R_FIFO_RAEM' undeclared (first use in this function)
fec_main.c:588:3: error: 'FEC_R_FIFO_RAFL' undeclared (first use in this function)
fec_main.c:591:3: error: 'FEC_OPD' undeclared (first use in this function)
Adding the missing register defines is not an option, since the registers
do not exist on MCF5272. Disable the added functionality for MCF5272 builds.
Cc: Frank Li <Frank.Li@freescale.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to restart autonegotiation via the PHY.
Tested on i.MX28EVK.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older Single Queue (SQ_SG_MODE) devices like TSEC (i.e. mpc83xx)
don't feature the frame receive indication bits (RXF) in RSTAT.
For these and for the rest of the SQ_SG_MODE devices, provide the
appropiate polling routine that handles a single pair of Rx/Tx
BD rings, removing the overhead incurred by the multiple queues/
multiple interrupt group devices (veTSEC/ eTSEC2.0 devices).
So this is primarily a fix for the TSEC devices.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 75096579c3 ("lib: devres: Introduce devm_ioremap_resource()")
introduced devm_ioremap_resource() and deprecated the use of
devm_request_and_ioremap().
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: netdev@vger.kernel.org
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save power, let's disable the regulator in the suspend function and
enable it in resume.
Tested on a mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe the clocks are enabled prior than the acquiring the interrupts.
In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of error during probe, disable the PHY regulator.
Do the same in fec_drv_remove().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.
This is wrong because at this point the interrupts have not even been acquired.
Swap failed_init/failed_irq to fix the error path.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard DIV_ROUND_UP macro in order to provide better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MVF is a family while MVF600 is a particular SoC in the family. We
generally prefer to use SoC rather than family name in compatible string
to define a particular type of fec device. And this is how fec_dt_ids
works for all those IMX fec variants. Let's change mvf to mvf600 to
have it work in the same way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing iounmap() before return from gianfar_ptp_probe()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 54309fa6 ("net: fec: fix kernel oops when plug/unplug cable many times")
introduced the following 'if' block in the beginning of fec_start():
if (netif_running(ndev)) {
netif_device_detach(ndev);
napi_disable(&fep->napi);
netif_stop_queue(ndev);
netif_tx_lock_bh(ndev);
}
Then later in the end of fec_restart() there is another block that calls the
opposite of each one of these functions.
The correct approach would be to also call them with in the reverse order, so
that we have as result:
if (netif_running(ndev)) {
netif_tx_unlock_bh(ndev);
netif_wake_queue(ndev);
napi_enable(&fep->napi);
netif_device_attach(ndev);
}
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c09eed (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants. This is inappropriate, because some variants like imx5 have
no such support on hardware. Consequently, fec is broken on these
platforms. Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUYgjh2CrR//JCVInAQJTvRAAmxaeoI+kQ/pbbRDa/Mnhf+bUmQjvJvx4
uFGYAAi23Txem2Bx6xrfvOo9//ATYSfRxenoSSOtXQucsnrqD0+837Sj2NbO6AB9
MSiFDK4usJtGwSUybkSHNLb2QPBr8XTgmyWVE/sHEw2UtrIToC1n3sxFofFm0guT
ReILKsgK0Wjyq5RntnjWOCHNNp6OGqDGvFXlSJqNA7Z6gR/VZy4o0oXS4Sv3TWgF
zG7ngSG7/u9FP1IQnMr/SxY1T4QS/bBbAC1YvD/7X30DPHrWKR3/3LfLcsc9TUN2
smTlZQjHdgBbGfVPL7JN0fQwA82HEjNSZKLJ0w9uFjxXgnoKT3znpUpQeuf3dsWm
BhEFqN1Rf446S4ft2btBSB2nhX4NTlJ7w6z2F65xgaylgYFsGFTYcpjiOurKe3wF
gGsw31DZdcuI4/LjiWbNGRKbMd7HFFLbFDMJ16TFbNcNr+pM3qpoQ6z3uMbfCBSe
xFnYr+ESN8F2HXMNLiz3CTqLY+Fi/bHd22n3KuI9qsWws/0KDUrTvFh9Sm3kYji5
QwwLl6PRoeFw8H29e3KrPsKoY/BGYAvrAetnC1o79cDFPLwUyii/1B6WwzC4ynfs
K1VhwdVOwnp0sS/a2Pv8sZBpDNI07gwT9P20aiholxgREq2RKNXXVxGGFfK5Qvm9
FG4Vp6EKEQ0=
=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.
Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.
The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An early draft of the PHC patch series included an alarm in the
gianfar driver. During the review process, the alarm code was dropped,
but the capability removal was overlooked. This patch fixes the issue
by advertising zero alarms.
This patch should be applied to every 3.x stable kernel.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reported-by: Chris LaRocque <clarocq@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Several call sites were missed when the protocol argument was added to
__vlan_hwaccel_put_tag() in commit
86a9bad3ab ("net: vlan: add protocol
argument to packet tagging functions").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the driver that requires <asm/coldfire.h> and
<asm/mcfsim.h>.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A link-down isn't properly saved in the FEC state, so we wouldn't restart the
FEC after a repeated link-up.
Regression was introduced with commit
d97e7497 "net: fec: restart the FEC when PHY speed changes"
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.
Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary macros that duplicate generic
kernel functions.
When a struct net_device is available:
Convert printks to netdev_<level>
Convert netif_msg_<foo> and ugeth_<level> to netif_<level>
Add pr_fmt. Standardize on newlines at end of format.
Remove some duplicated newlines from output.
Coalesce formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
Convert pr_<level> to netdev_<level> when a struct net_device is
available. Add pr_fmt and neaten other formats too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging message style.
Convert the printks where a struct net_device is available to
netdev_<level>. Convert the other printks to pr_<level> and
add pr_fmt where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when booting a mx6 device we get the following on boot:
registered PHC device on eth%d
Fix it by printing the network device name only after it gets registered, so
that the following can be read now:
fec 2188000.ethernet eth0: registered PHC device 0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale Vybrid platform implentments MAC-ENET core
providing compatibility with half- or full-duplex
10/100 Mbit/s Ethernet LANs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MX28 boards need the internal enet_out clock to be enabled. So, do
this in the driver iff the clock was referenced via devicetree.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
When the optional clk_ptp is absent, we can just set it to NULL, and
clk API will just handle it gracefully. It saves us from checking
clk_ptp whenever calling into clk API.
Also since clk_ptp is optional, the "ret" variable shouldn't be set
in case that the clock is absent.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Since of_get_mac_address() is now defined even if CONFIG_OF_NET
is not configured, the ifdef around the code calling it is no longer
necessary and can be removed.
Similar, since of_get_phy_mode() is now defined as dummy function
if OF_NET is not configured, it is no longer necessary to provide
an OF dependent function as front-end. Also, the function depends
on OF_NET, not on OF, so the conditional code was not correct anyway.
Drop the front-end function and call of_get_phy_mode() directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch
1. boot with nfs (no_console_suspend)
2. echo mem >/sys/power/state
3. wakeup by wakesource
4. print "eth0: tx queue full"
This fix above problem by reinit bd queue at restart function
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX Buffer in fec_enet_alloc_buffers was being initialized
with the receive register define BD_ENET_RX_INT instead of
the transmit register define BD_ENET_TX_INT
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_ptp.ko can't run individually
rename fec.c to fec_main.c
Build fec.o and fec_ptp.o into one fec.ko
Remove unnessary EXPORT_SYMBOL in fec_ptp
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRO_DROP return code is handled by the core network layer.
The current kernel approach is to factorize this kind of statistics into
the upper layers, instead of having all the drivers maintaining them.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning message:
warning: 'budget_per_q' may be used uninitialized in this function
budget_per_q won't be used uninitialized since the only time
it doesn't get initialized is when entering gfar_poll with
num_act_queues == 0, meaning rstat_rxf == 0, in which case
budget_per_q is not utilized (as it has no meaning).
Inititalize budget_per_q to 0 though to suppress this compile
warning.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_poll_controller() was not declared. It should be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only place where gfar_configure_coalescing is called
with an actual bitmask (other than 0xff) is in gfar_poll
(on the hot path). So make gfar_configure_coalescing()
static for the buffer processing path, and export
gfar_configure_coalescing_all() for the remaining cases
that require to set coalescing for all the queues at once
(on the slow path).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Multi Q Multi Group (MQ_MG_MODE) mode, the Rx/Tx colescing registers [rt]xic
are aliased with the [rt]xic0 registers (coalescing setting regs for Q0). This
avoids programming twice in a row the coalescing registers for the Rx/Tx hw Q0.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the napi budget fairly among the active queues only, instead
of dividing it by the total number of Rx queues assigned to the
given interrupt group.
Use the h/w indication field RXFi in rstat (receive status register)
to identify the active rx queues from the current interrupt group
(i.e. receive event occured on ring i, if ring i is part of the current
interrupt group). This indication field in rstat, RXFi i=0..7,
allows us to find out on which queues of the same interrupt group
do we have incomming traffic once we entered the polling routine for
the given interrupt group. After servicing the ring i, the corresponding
bit RXFi will be written with 1 to clear the active queue indication for
that ring.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 issues with the current napi poll routine, with regards
to tx ring cleanup:
1) for multi-queue devices (MQ_MG_MODE), should tx_bit_map != rx_bit_map,
which is possible (and supported in h/w) if the DT property "fsl,tx-bit-map"
holds a different value than rx_bit_map, the current polling routine will
service the wrong Tx queues in this case (i.e. the interrupt group will
receive interrupts from tx queues that it will not service)
2) Tx cleanup completion consumes napi budget, whereas the napi budget
should be reserved for Rx work only.
The patch fixes these issues and provides a clean napi polling routine.
Napi poll completion is reached when all the Rx queues have been
serviced and there is no Tx work to do.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings that happen when building with W=1 option:
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_free_buffers':
drivers/net/ethernet/freescale/fec.c:1337:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers':
drivers/net/ethernet/freescale/fec.c:1361:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_init':
drivers/net/ethernet/freescale/fec.c:1631:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dc975382d2 introduces napi support
but never calls napi_disable. This will generate a kernel oops
(kernel BUG at include/linux/netdevice.h:473!) every time, when
ndo_stop is called followed by ndo_start.
Add the missing napi_diable call.
Signed-off-by: Georg Hofmann <georg@hofmannsweb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.
Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI header is not needed, so get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build error cause by
Commit ff43da86c6
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
Commit ee873fda3b ("gianfar: Pack struct
gfar_priv_grp into three cachelines") moved the irq number and names
off into a separate struct and created accessors for them. However
it was never tested with NET_POLL enabled, and so some conversions
that were simply overlooked went undetected until now.
Make the netpoll ones also use the gfar_irq() accessors.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff90702: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
commit 7f7d6c282 (net: fec: Ensure that initialization is done prior to
request_irq()) placed fec_ptp_init() into a point that ptp clock was not
available, which causes a division by zero in fec_ptp_start_cyclecounter():
[ 17.895723] Division by zero in kernel.
[ 17.899571] Backtrace:
[ 17.902094] [<80012564>] (dump_backtrace+0x0/0x10c) from [<8056deec>]
(dump_stack+0x18/0x1c)
[ 17.910539] r6:bfba8500 r5:8075c950 r4:bfba8000 r3:bfbd0000
[ 17.916284] [<8056ded4>] (dump_stack+0x0/0x1c) from [<80012688>]
(__div0+0x18/0x20)
[ 17.923968] [<80012670>] (__div0+0x0/0x20) from [<802829c4>] (Ldiv0+0x8/0x10)
[ 17.931140] [<80398534>] (fec_ptp_start_cyclecounter+0x0/0x110) from
[<80394f64>] (fec_restart+0x6c8/0x754)
[ 17.940898] [<8039489c>] (fec_restart+0x0/0x754) from [<803969a0>]
(fec_enet_adjust_link+0xdc/0x108)
[ 17.950046] [<803968c4>] (fec_enet_adjust_link+0x0/0x108) from [<80390bc4>]
(phy_state_machine+0x178/0x534)
...
Fix this by rearraging the code so that fec_ptp_init() is called only after
the clocks have been properly acquired.
Tested on both mx53 and mx6 platforms.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently request_irq() is called prior to fec_enet_init() and fec_ptp_init(),
which causes the following crash on a mx53qsb:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = 80004000
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.8.0-rc7-next-20130215+ #346)
PC is at fec_enet_interrupt+0xd0/0x348
LR is at fec_enet_interrupt+0xb8/0x348
pc : [<80372b7c>] lr : [<80372b64>] psr: 60000193
sp : df855c20 ip : df855c20 fp : df855c74
r10: 00000516 r9 : 1c000000 r8 : 00000000
r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : df9b7800
r3 : df9b7df4 r2 : 00000000 r1 : 00000000 r0 : df9b7d34
Ensure that such initialization functions are called prior to requesting the
interrupts, so that all necessary the data structures are in place when the
irqs occur.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether the phy-reset GPIO is valid, prior to requesting it.
In the case a board does not provide a phy-reset GPIO, just returns immediately.
With such gpio validation in place, it is also safe to change from pr_debug to
dev_err in the case the gpio request fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a less obvious error on one hand, and prevents futher
similar errors by disambiguating and optimizing RxFCB indication,
on the other hand.
The error consists in NETIF_F_HW_VLAN_TX flag being used as an
indication of Rx FCB insertion. This happened as soon gfar_uses_fcb(),
which despite its name indicates Rx FCB insertion, started
incorporating is_vlan_on().
is_vlan_on(), on the other hand, is also a misleading construct because
we need to differentiate b/w hw VLAN extraction/VLEX (marked by VLAN_RX
flag) and hw VLAN insertion/VLINS (VLAN_TX flag), which are different
mechanisms using different types of FCBs.
The hw spec for the RxFCB feature is as follows:
In the case of RxBD rings, FCBs (Frame Control Block) are inserted by
the eTSEC whenever RCTRL[PRSDEP] is set to a non-zero value. Only one
FCB is inserted per frame (in the buffer pointed to by the RxBD with
bit F set). TOE acceleration for receive is enabled for all rx frames
in this case.
This patch introduces priv->uses_rxfcb field to quickly signal RxFCB
insertion in accordance with the specification above.
The dependency on FSL_GIANFAR_DEV_HAS_TIMER was also eliminated as
another source of confusion. The actual dependency is to priv->hwts_rx_en.
Upon changing priv->hwts_rx_en via IOCTL, the gfar device is being
restarted and on init_mac() the priv->hwts_rx_en flag determines RxFCB
insertion, and rctrl is programmed accordingly. The patch takes care
of this case too.
Though maybe not as self documenting as the inlining version uses_fcb(),
priv->uses_rxfcb has the main purpose to quickly signal, on the hot path,
that the incoming frame has a *Rx* FCB block inserted which needs to be
pulled out before passing the skb to the stack. This is a performance
critical operation, it needs to happen fast, that's why uses_rxfcb is
placed in the first cacheline of gfar_private.
This is also why a cached rctrl cannot be used instead: 1) because
we don't have 32 bits available in the first cacheline of gfar_priv
(but only 16); 2) bit operations are expensive on the hot path.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The controller's ref manual states clearly that when the hw Rx vlan
offload feature is enabled, meaning that the VLEX bit from RCTRL is
correctly enabled, then the hw performs automatic VLAN tag extraction
and deletion from the ethernet frames. So there's no point in trying to
increase the rx buff size when rxvlan is on, as the frame is actually
smaller.
And the Tx vlan hw accel feature (VLINS) has nothing to do with rx buff
size computation.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No return code is expected from gfar_process_frame(), hence
change it to return void.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group run-time critical fields within the 1st cacheline (32B)
followed by the tx|rx_queue reference arrays and the interrupt
group instances (gfargrp), all cacheline aligned.
This has several benefits. Firstly comes the performance benefit
by having the members required by the driver's hot path re-grouped
in the structure's first cache lines, whereas the unimportant
members were pushed towards the end of the struct.
Another benefit comes from eliminating a 24 byte memory hole that
was rendering gfar_priv's 2nd cacheline useless. The default gcc
layout of gfar_private leaves an implicit 24 byte hole after the
errata (enum) member. This patch fixes it.
The uchar bitfields were pushed towards the end of the struct
as these are not run-time performance critical (used for init
time operations). Because there is no other 2 byte member
around to couple the uchar bitfields memeber with, we will
have an addititnal 2 byte hole after the bitfields. This is
unsignificant however, and it doesn't influence gfar_priv's
size, because the whole structure is padded to be a 32B multiple.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device pointer (dev) to simplify the code and to
avoid double indirections, especially on the hot path.
Basically, instead of accessing priv to get the ofdev
reference and then accessing the ofdev structure to
dereference the needed dev pointer, we will get the
dev pointer directly from priv.
The dev pointer is required on the hot path, see gfar_new_rxbdp
or gfar_clean_rx_ring (or xmit), and this patch makes
it available directly from priv's 1st cacheline.
This change is reflected at asm level too, taking (the hot)
gfar_new_rxbdp():
initial version -
18c0: 7c 7e 1b 78 mr r30,r3
18d0: 81 69 04 3c lwz r11,1084(r9)
18d8: 34 6b 00 10 addic. r3,r11,16
18dc: 41 82 00 08 beq- 18e4
patched version -
18d0: 80 69 04 38 lwz r3,1080(r9)
18d8: 2f 83 00 00 cmpwi cr7,r3,0
18dc: 41 9e 00 08 beq- cr7,18e4
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker says:
====================
Eric noticed that the handling of local u64 ethtool counters for
this driver commonly found on Freescale ppc-32 boards was racy.
However, before converting them over to atomic64_t, I noticed
that an internal struct was being used to determine the offsets
for exporting this data into the ethtool buffer, and in doing
so, it assumed that the counters would always be u64. Rather
than keep this implicit assumption, a simple code cleanup gets
rid of the struct completely, and leaves less conversion sites.
The alternative solution would have been to take advantage of
the fact that the counters are all relating to error conditions,
and hence make them internally u32. In doing so, we'd be assuming
that U32_MAX of any particular error condition is highly unlikely.
This might have made sense if any increments were in a hot path.
Tested with "ethtool -S eth0" on sbc8548 board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at some asm dump for an unrelated change, Eric
noticed in the following stats count increment code:
50b8: 81 3c 01 f8 lwz r9,504(r28)
50bc: 81 5c 01 fc lwz r10,508(r28)
50c0: 31 4a 00 01 addic r10,r10,1
50c4: 7d 29 01 94 addze r9,r9
50c8: 91 3c 01 f8 stw r9,504(r28)
50cc: 91 5c 01 fc stw r10,508(r28)
that a 64 bit counter was used on ppc-32 without sync
and hence the "ethtool -S" output was racy.
Here we convert all the values to use atomic64_t so that
the output will always be consistent.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The gfar_stats struct is only used in copying out data
via ethtool. It is declared as the extra stats, followed
by the rmon stats. However, the rmon stats are never
actually ever used in the driver; instead the rmon data
is a u32 register read that is cast directly into the
ethtool buf.
It seems the only reason rmon is in the struct at all is
to give the offset(s) at which it should be exported into
the ethtool buffer. But note gfar_stats doesn't contain
a gfar_extra_stats as a substruct -- instead it contains
a u64 array of equal element count. This implicitly means
we have two independent declarations of what gfar_extra_stats
really is. Rather than have this duality, we already have
defines which give us the offset directly, and hence do not
need the struct at all.
Further, since we know the extra_stats is unconditionally
always present, we can write it out to the ethtool buf
1st, and then optionally write out the rmon data. There
is no need for two independent loops, both of which are
simply copying out the extra_stats to buf offset zero.
This also helps pave the way towards allowing the extra
stats fields to be converted to atomic64_t values, without
having their types directly influencing the ethtool stats
export code (gfar_fill_stats) that expects to deal with u64.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Until now, the MPC5200 FEC ethernet driver relied upon the bootloader
(U-Boot) to write the MAC address into the ethernet controller
registers. The Linux driver should not rely on such a thing. So
lets read the MAC address from the DT as it should be done here.
The following priority is now used to read the MAC address:
1) First, try OF node MAC address, if not present or invalid, then:
2) Read from MAC address registers, if invalid, then:
3) Log a warning message, and choose a random MAC address.
This fixes a problem with a MPC5200 board that uses the SPL U-Boot
version without FEC initialization before Linux booting for
boot speedup.
Additionally a status line is now be printed upon successful
driver probing, also displaying this MAC address.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.8.0-rc5+ #82 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&fep->hw_lock)->rlock){..-...}, at: [<8034e2f8>] fec_enet_start_xmit+0x48/0x 2cc
but this lock took another, SOFTIRQ-unsafe lock in the past:
(prepare_lock){+.+.+.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(prepare_lock);
local_irq_disable()
lock(&(&fep->hw_lock)->rlock);
lock(prepare_lock);
<Interrupt>
lock(&(&fep->hw_lock)->rlock);
*** DEADLOCK ***
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old method will cause init spinlock twice.
New method will avoid init spinlock twice and fix miss init spinlock
at fec_restart.
BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
[<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
[<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
[<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
r5:805f6f8c r4:bfae0f8c
[<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0 )
r5:806b4950 r4:bfae0f8c
[<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs ave+0x18/0x20)
[<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_ cyclecounter+0x3c/0x120)
r4:bfae0f8c r3:00000002
[<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta rt+0x56c/0x5f8)
r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
[<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee873fda3b
"gianfar: Pack struct gfar_priv_grp into three cachelines"
causes the following null dereference at driver init on sbc8548:
libphy: Freescale PowerQUICC MII Bus: probed
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01d6a38
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01d6a38] gfar_parse_group+0x228/0x280
LR [c01d6a34] gfar_parse_group+0x224/0x280
Call Trace:
[ef82dd60] [c01d6a34] gfar_parse_group+0x224/0x280 (unreliable)
[ef82dd90] [c01d73a4] gfar_probe+0x284/0xfe0
The reason is that the commit also changed the allocation of the
Rx and error handling irq structs to be skipped for !MQ_MG_MODE.
In the !MQ_MG_MODE case, only the Tx irq struct is allocated.
Digging further, we see that MQ_MG_MODE is set only if we find
the OF compatible string "fsl,etsec2".
A quick grep in the dts directory shows lots of boards that support
Rx/Tx/Err, but without this specific compat string. And hence they
go after the unallocated Rx/Error structs and cause the above oops.
Hence such a change can not be deployed until all the dts files
are updated and sufficiently deployed. Further, the optimization
is of limited value, since the kmalloc'd struct in question has only
a single unsigned int, and an (IFNAMSIZ + 6) sized string.
Note that no changes to the freeing code are needed here, as it
already did an unconditional free of Rx/Tx/Error gfar_irqinfo.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove unused members(!): imask, ievent
* move space consuming interrupt name strings (int_name_* members) to
external structures, unessential for the driver's hot path
* keep high priority hot path data within the first 2 cache lines
This reduces struct gfar_priv_grp from 6 to 3 cache lines.
(Also fixed checkpatch warnings for the old code, in the process.)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out redundant code (improve readability, source code size).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resize and regroup structure members to eliminate memory holes and
to pack the structure into 2 cache lines (from 3).
tx_ring_size was resized from 4 to 2 bytes and few members were re-grouped
in order to eliminate byte holes and achieve compactness.
Where possible, few members were grouped according to their usage and access
order (i.e. start_xmit vs. clean_tx_ring members), less important members
were pushed at the end.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the
net dev requires it (IFF_PROMISC flag set).
This way the promisc mode is preserved accross device reset conditions
like tx timeout, device restore, a.s.o.
Signed-off-by: Voncken C Acksys <cedric.voncken@acksys.fr>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in/out_be32 accessors are Power arch centric whereas
ioread/writebe32 are available in other arches. Also, unlike
in/out_be32, ioread/writebe32 expect non-volatile address arguments.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning when building with W=1 option:
drivers/net/ethernet/freescale/fec.c:810:1: warning: '__inline__' is not at beginning of declaration [-Wold-style-declaration]
The inline declaration is pointless in this function, so just remove it.
While at it, also remove the other 'inline' declarations.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report correct hardware stamping capability by ethtool interface.
The v1.0 ptp4l check it.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
MX6 and mx28 support enhanced DMA descriptor buff to support 1588
ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff.
Check fec type and choose correct DMA descriptor buff type.
Remove static config CONFIG_FEC_PTP.
ptp function will be auto detected.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families. Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives
are updated for the new file locations.
Tested by recompiling for MPC5200 with all bestcomm users enabled.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Beside imx6q, the kernel built from imx_v6_v7_defconfig is also
supposed to be running on other IMX SoCs that do not have the PTP
block. Before fec driver gets fixed to run-time detect target hardware
rather than conditional compiling with #ifdef CONFIG_FEC_PTP, let's
give it a quick fix in Kconfig to forbid FEC_PTP on those IMX SoCs that
do not support PTP.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gianfar ethernet device is down prior to hibernating a
system, it will no longer be present upon system restore.
For example:
~# ifconfig eth0 down
~# echo disk > /sys/power/state
<trigger a restore from hibernation>
~# ifconfig eth0 up
SIOCSIFFLAGS: No such device
This happens because the restore function bails out early upon
finding devices that were not up at hibernation. In doing so,
it never gets to the netif_device_attach call at the end of
the restore function. Adding the netif_device_attach as done
here also makes the gfar_restore code consistent with what is
done in the gfar_resume code.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should gfar_init_bds() return with -ENOMEM inside gfar_alloc_skb_resources(),
free_skb_resources() will be called twice in a row on the "cleanup" path,
leading to duplicate kfree() calls for rx_|tx_queue->rx_|tx_skbuff resulting
in segmentation fault.
This patch prevents the segmentation fault to happen in the future
(rx_|tx_sbkbuff set to NULL), and corrects the error path handling
for gfar_init_bds().
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move below calculate out of spin lock section
diff = fep->cc.mult;
diff *= ppb;
diff = div_u64(diff, 1000000000ULL);
diff is local variable and not neccesary in spin lock
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PPS.
Limit FEC_PTP option for i.MX chip only.
FEC_PTP default is on at mx6 platform.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a 36 bit dtb file, the driver complains "resource busy".
Investigating the source of the message leads one to the
gianfar_ptp_probe function.
Since the type of the device resource requested in this function
is IORESOURCE_MEM, it should use "iomem_resource" instead of
"ioports_resource".
Signed-off-by: Wei Yang <Wei.Yang@windriver.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch:
acb600d net: remove skb recycling
added dev_free_skb() to drivers/net/ethernet/freescale/ucc_geth.c
This is a typo and should be dev_kfree_skb(). This fixes this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit
87151b8689 (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is primarily to address transmission timeout occurrences, when
multiple H/W Tx queues are being used concurrently. Because in
the priority scheduling mode the controller does not service the
Tx queues equally (but in ascending index order), Tx timeouts are
being triggered rightaway for a basic test with multiple simultaneous
connections like:
iperf -c <server_ip> -n 100M -P 8
resulting in kernel trace:
NETDEV WATCHDOG: eth1 (fsl-gianfar): transmit queue <X> timed out
------------[ cut here ]------------
WARNING: at net/sched/sch_generic.c:255
...
and controller reset during intense traffic, and possibly further
complications.
This patch changes the default H/W Tx scheduling setting (TXSCHED)
for multi-queue devices, from priority scheduling mode to a weighted
round robin mode with equal weights for all H/W Tx queues, and
addresses the issue above.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build failure introduced in commit 66636287
("gianfar: Support the get_ts_info ethtool method."). Not only was a
global variable inconsistently named, but also it was not exported as
it should have been.
This fix is also needed in stable version 3.5.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the 'net' tree to get the recent set of netfilter bug fixes in
order to assist with some merge hassles Pablo is going to have to deal
with for upcoming changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO controller on the Frame Manager (Fman) is compatible with the
QE and Gianfar MDIO controllers, but we don't care about the TBI because
the Ethernet drivers (FMD) take care of programming it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of the new mdiobus_alloc_size() function to combine three
different memory allocations into one. This also simplies the error
handling.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the device tree probe function more data-driven, so that it no longer
searches the 'compatible' property more than once. The of_device_id[] array
allows for per-entry private data, so we use that to store details about each
type of node that the driver supports. This removes the need to check the
'compatible' property inside the probe function.
The driver supports four types on MDIO devices:
1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)
Gianfar, eTSEC2, and QE have different mappings for the TBIPA register, which
is needed to initialize the TBI PHY. In addition, the QE needs a special
hack because of the way the device tree is ordered.
All of this information is encapsulated in the fsl_pq_mdio_data structure,
so when an MDIO node is probed, per-device data and functions are used
to determine how to initialize the device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Replace printk with dev_err
2) Fix some whitespace mistakes
3) Rename "ofdev" to "pdev", since it's a platform_device now
4) Fix an inadvertent compound statement by replacing commas with semicolons
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few small functions were called only by other functions in the same
file, so merge them together. One function, for example, was calculating
the device address even though the caller was doing the same thing.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of the functions in fsl_pq_mdio.c are used by any other source file,
so there's no point in exporting them. Merge the header file into the
source file, make all the functions static, remove any EXPORT_SYMBOL
statements, and delete any #include "fsl_pq_mdio.h" statements.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit -
"b852b72 gianfar: fix bug caused by
87c288c6e9aa31720b72e2bc2d665e24e1653c3e"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to fsl_pq_mdio.c, this driver is for the 10G MDIO controller on
Freescale Frame Manager Ethernet controllers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit db83d136d7 (gianfar: Fix missing sock reference when
processing TX time stamps) added a potential sk_wmem_alloc imbalance
If the new skb has a different truesize than old one, we can get a
negative sk_wmem_alloc once new skb is orphaned at TX completion.
Now we no longer early orphan skbs in dev_hard_start_xmit(), this
probably can lead to fatal bugs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jiajun Wu <b06378@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro spin_event_timeout() was designed for simple polling of hardware
registers with a timeout, so use it when we poll the MIIMIND register.
This allows us to return an error code instead of polling indefinitely.
Note that PHY_INIT_TIMEOUT is a count of loop iterations, so we can't use
it for spin_event_timeout(), which asks for microseconds.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different boards may require different phy reset duration. Add property
phy-reset-duration for device tree probe, so that the boards that need
a longer reset duration can specify it in their device tree.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using gpio_request_one will require the probe fail-out call gpio_free,
which is missing currently. Change to use devm_gpio_request_one to
fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bootloader or platform initialization code does not enable the
power supply to fec phy, we need to do it in fec driver before calling
fec_reset_phy to have the phy powered on.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that bootloader or platform initialization does not set up
fec pins, the fec_reset_phy will not be able to succeed, because
fec_reset_phy is currently called before devm_pinctrl_get_select_default.
Move fec_reset_phy call to the place between devm_pinctrl_get_select_default
and fec_enet_init to have above case be taken care.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_defer_rx_timestamp was called with a freshly allocated skb but must
be called with rskb instead.
Signed-off-by: Stephan Gatzka <stephan@gatzka.org>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
FCB(Frame Control Block) isn't the part of netdev hard header.
Add FCB to hard_header_len will make GRO fail at MAC comparision stage.
Signed-off-by: Jiajun Wu <b06378@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: netdev@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Shawn Guo <shawn.guo@linaro.org> writes:
mxs common clk porting for v3.5. It depends on the following two branches.
[1] git://git.linaro.org/people/mturquette/linux.git clk-next
[2] http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm.git clkdev
As the mxs device tree conversion will constantly touch clock files,
to save the conflicts, the updated mxs/dt branch coming later will
based on this pull-request.
* 'clk/mxs' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: remove now unused timer_clk argument from mxs_timer_init
ARM: mxs: remove old clock support
ARM: mxs: switch to common clk framework
ARM: mxs: change the lookup name for fec phy clock
ARM: mxs: request clock for timer
clk: mxs: add clock support for imx28
clk: mxs: add clock support for imx23
clk: mxs: add mxs specific clocks
Includes an update to Linux 3.4-rc6
Conflicts:
drivers/clk/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Space allocated for int_name_<foo> is insufficient for
maximal device name, expand it.
Code to create int_name_<foo> is obscure, simplify it
by using sprintf.
Found by looking for unnecessary \ line continuations.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for MPC5125 FEC. The FEC on MPC5125 additionally
supports RMII PHY interface. Configure controller/PHY interface type
according to the optional phy-connection-type property in the ethernet
node. This property should be either "rmii" or "mii".
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __netif_subqueue_stopped() just does the following:
struct netdev_queue *txq = netdev_get_tx_queue(dev, queue_index);
return netif_tx_queue_stopped(txq);
and since we already have the txq in scope, we can just call that
directly in this case.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were two version strings, and neither one was being used.
Also in the same proximity were some unused #define that were
left over from the past. Delete them all.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add support for byte queue limits (BQL), based on the similar
modifications made to intel/igb/igb_main.c from Eric Dumazet
in commit bdbc063129
"igb: Add support for byte queue limits."
A local variable for tx_queue->qindex was introduced in
gfar_clean_tx_ring, since it is now used often enough to warrant it,
and it cleans up the readability somewhat as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Factor out the the existing allocation and free operations
so that they can be used individually.
This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).
This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself. Local variables are relocated as necessary.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
