This patch moves code for wowlan magic-packet and patterns to a function
mwifiex_set_mef_filter.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of these messages.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As we are releasing the lock, during next iteration we may end
up getting page fault if other thread has already deleted that
node.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wakeup pending wait queues in unload path. This will help to avoid
soft lockup issues in corner cases.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If host fails to wakeup the firmware, we will trigger card reset
after 3 second timeout.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
200ms is the requirement to allow VDD1.1 and VDD1.8 to
drop to have proper reset.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Workqueue needs to be flushed early when removing card, otherwise
soft lockup issue may happen because main_process is triggered by
interrupt while card is being removed.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This flag is never set but checked at two places. We will get rid of
this code.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to get number of BA streams
supported information from FW. Some newer chips(e.g. 8897 series)
support 4 BA streams for TX; so driver should not disallow BA stream
setup just after 2 streams have been established.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for DMA alignment of 64 bytes for TX packets.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes memory corruption reported by community developer.
"Memory corruption occurs in mwifiex_ret_802_11_key_material_v1()
when a short command response is received without a key length
causing non initialised memory to be interpreted as the key
length resulting in a memcpy() overwriting the part of the
driver's private data structure beyond the key area."
For v1 key material API firmwares, there is no need to send
command to delete WEP key. WEP encryption/decryption is controlled
by mac_control command.
This patch avoids sending key material command in del_key case.
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the bcm43340 and bcm43341 wireless
chipsets. These two chipsets are identical from wireless parts
perspective. As such they use the same firmware image.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rob Herring <rob.herring@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
[arend@broadcom.com: squash to single commit, remove 43341 chipid]
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds module parameter for auto deepsleep configuration.
By default, module_param is 0 and auto deep sleep is enabled.
If mwifiex driver is loaded with disable_auto_ds=1, deep sleep
configuration would not be downloaded to FW and FW would not enter
deepsleep upon initializing.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch saves sdio registers value before firmware dump,
this can be used to find out reason for FW dump.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to dump driver information to a file
when firmware dump happens. This information can be used to
root casue FW crash.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_debug_info also need be save to file when firmware dump happens.
Move its dump implementation function to commmon utilility file, thus it
can be reused in firmware dump function.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move mwifiex_pm_wakeup_card_complete handler to source file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add a new debugfs item histogram used for reporting
rx data packet statitics(rx rate, snr, noise floor, signal strenth)
to userspace.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add receive beacon count and miss beacon count statistics
in debugfs getlog item.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add provision to show TDLS peer table in debugfs file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver gets beacon info containing a country IE from user-space
upon .start_ap() callback, it will enable regulatory 802.11d support.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cfg80211 change_station to signal the completion of 802.1x
to firmware. This allows FW to take appropriate actions.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user-space uses a valid ISO-3166-1 country code for its
regulatory domain selection, the driver will try to configure
the firmware to use the same.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When there is no room in the ring for rxbufpost an error is logged,
however this happens quite frequently and can be considered normal
and is certainly recoverable. This patch changes the erorr into
a normal msgbuf log.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a device is configured for AP mode and it is configured for
WEP then the keys are plumbed first, followed by AP configuration.
During configuration a down command is given to the firmware which
will clear the configured keys. This patch reprograms the WEP keys
after AP has been brought up.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The source file chip.c contained some duplicate defines and
some unused ones. Removing them.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The physical addresses being used by pcie and msgbuf were using
a cast to long, which incorrectly caused it to limit the address
to 32bit. Now explicit u64 is used where needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gLE1
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2014-12-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* more work on d0i3 power state
* enhancements to the firmware debugging infrastructure
* support for 2 concurrent channel contexts
* fixes / cleanups in the rate control
* general cleanups
This allows 3160 / 7260 / 7265 / 7265D / 8000 devices to
use the latest version of the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.
This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flag that enables match found notification to align with
FW API change.
Cc: <stable@vger.kernel.org> [3.17+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When tid_tspec was set to IWL_TID_NON_QOS (8) this led to an
out of bounds access to the tid_to_mac80211_ac array whose size
is 7. Fix this.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
commit 5c90422439
"iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it"
broke Rx with 2 chains for diversity.
This had an impact on throughput where we're using only a single
stream (11a/b/g APs, single stream APs, static SMPS).
Fixes: 5c90422439 ("iwlwifi: mvm: don't allow diversity if BT Coex / TT forbid it")
Cc: Stable <stable@vger.kernel.org> [3.16+]
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The trans cfg was not replaced for 7265-D cards. This led to a check of
the min-NVM version against a 7265-C card, causing very-old 7265-D cards
to operate incorrectly with the driver.
Fixes: 3fd0d3c170 ("iwlwifi: pcie: support 7265-D devices")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This driver uses the function, clocksource_khz2mult, and so it really must
include clocksource.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* ath9k: enable Transmit Power Control (TPC) for ar9003 chips
* rtlwifi: cleanup and updates from the vendor driver
* rsi: fix memory leak related to firmware image
* ath: parameter fix for FCC DFS pattern
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUpqFFAAoJEG4XJFUm622brwUH/iLBBtWvqbhFMKDlA9eUG0hD
z+LQkPtNR5gLYk11Qne7H8BjILDWgzdQcbyAUEpCnuplDThCDfj+8JB51gfNGpqU
pv9XwVO2Nf0afh4+hJBkBREI0vAJDod860AG+PV3E5G/WZZyt2MDxF9mk3IbvKVd
APR7cnUxsAltxjr7IWvPFY43wtbRJHbGM8EUVGkXDBaARaPipTJ7GqhwUyv45jCo
LRnW0VQ5njMZZD6DfteB9BiE+2GfZF9Ay4aOzRVJGc83NMHDBQxD7VSHVrBBgCt1
L+Ikz8O0UHG9TsoAGZqEcJ12o2iGWjVFm4TecEYsuhRA1fJmXJOispl/lnudZus=
=ZbEI
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Changes:
* ath9k: enable Transmit Power Control (TPC) for ar9003 chips
* rtlwifi: cleanup and updates from the vendor driver
* rsi: fix memory leak related to firmware image
* ath: parameter fix for FCC DFS pattern
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the function smt_ifconfig() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
dbgi_rd_rsp3() dbgi_wr_addr3()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg say:
====================
pull request: bluetooth-next 2014-12-31
Here's the first batch of bluetooth patches for 3.20.
- Cleanups & fixes to ieee802154 drivers
- Fix synchronization of mgmt commands with respective HCI commands
- Add self-tests for LE pairing crypto functionality
- Remove 'BlueFritz!' specific handling from core using a new quirk flag
- Public address configuration support for ath3012
- Refactor debugfs support into a dedicated file
- Initial support for LE Data Length Extension feature from Bluetooth 4.2
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.
Also, the hardcoded clock value is not a proper way for all SoCs.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the reset is just clock setting, individual mdio reset is
not available.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is based on stmmac driver.
changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)
changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of -1 with EAGAIN, read on a O_NONBLOCK tun fd will return 0. This
fixes this by properly returning the error code from __skb_recv_datagram.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validated that this was actually using the unsigned comparison with gdb.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds generic statistics for enic. As of now dma_map_error is the only
member. dma_map_erro is incremented every time dma maping error happens.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks for pci_dma_mapping_error() after dma mapping the data.
If the dma mapping fails we remove the previously queued frags and return
NETDEV_TX_OK.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes vnic_wq_buf doubly liked list. This is needed for dma_mapping
error check, in case some frag's dma map fails, we need to move back and remove
previously queued buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us
Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following spare warning:
drivers/net/ethernet/freescale/gianfar.c:3521:60: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:3521:60: expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:3521:60: got unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16: warning: incorrect type in assignment (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:205:16: expected unsigned int [usertype] *rfbptr
drivers/net/ethernet/freescale/gianfar.c:205:16: got unsigned int [noderef] <asn:2>*<noident>
drivers/net/ethernet/freescale/gianfar.c:2918:44: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/freescale/gianfar.c:2918:44: expected unsigned int [noderef] <asn:2>*addr
drivers/net/ethernet/freescale/gianfar.c:2918:44: got unsigned int [usertype] *rfbptr
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to do header check for virtio-net since:
- Host sets dodgy for all gso packets from guest and check the header.
- Host should be prepared for all kinds of evil packets from guest, since
malicious guest can send any kinds of packet.
So this patch sets NETIF_F_GSO_ROBUST for virtio-net to skip the check.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the end asm/mach/irda.h header is not used by anybody except sa1100.
Move the header to the platform data includes dir and rename it to
irda-sa11x0.h.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timecounter implementation will drop a variable amount
of resolution, depending on the magnitude of the time delta. In
other words, reading the clock too often or too close to a time
stamp conversion will introduce errors into the time values. This
patch fixes the issue by introducing a fractional nanosecond field
that accumulates the low order bits.
Reported-by: Janusz Użycki <j.uzycki@elproma.com.pl>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will remove the bug of havine zero perm_extended_addr address.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If allocation of memory fails instead of going to ret goto label
and returning from there, we can directly return -ENOMEM on failure.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Organize and cleanup the consts used by rs.
This is part of making some of these configurable.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make passive scan fragmentation depends on the number of active
interfaces. In case of single-MAC, make passive scan less fragmented.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to config the FW and to allocate monitor buffer driver should
run the function iwl_pcie_apply_destination immediately after FW sections
are loaded.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This configuration defines the ratio between number of scan iterations
where EBS is involved to those where it is not.
This configuration was left unconfigured due to inaccurate documentation.
Fix documentation as well.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set the wakeup flag (of the d3 command) to configure the fw
to wakeup when sysassert happens while in d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A new TLV supplies the ADMA address for SDIO mode, allowing
the driver to configure the default base address to be this
(as given in the FW), rather than hardcoding the values to
use until the FW sends the ALIVE message.
Use the value given by the FW in the IWL_UCODE_TLV_SDIO_ADMA_ADDR
TLV for setting the default SDTM base address until the FW sends
the ALIVE message. If it isn't given in the FW - use the current
hardcoded values.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A number of places (still) use a direct operation, use
iwl_mvm_sta_from_mac80211() consistently. In one place
also move it into the variable initializer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are a few places not using it, use it at those places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some implementations (i.e. mini_rpm) assume the references
are managed only while the device is started.
Move the stale reference cleanup before stopping the
device in order to make them happy.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver and the firmware now support 2 different channels
at the same time. Advertise this capability to the stack.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
On hw restart, make sure to wait for d0i3 exit
(by checking the IN_D0I3 status bit).
This is needed in order to avoid the stale
d0i3_exit_work from doing harm (e.g. unref
cleared reference).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Consider the iwlwifi module param d0i3_disable when
considering whether d0i3 is supported.
(There is currently no need to differentiate between
supported and enabled, so keep the function as-is)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.
Use this mode in case of pcie trans.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Allow configuring additional d0i3 mode, in which the
fw will be configured to enter d0i3 only on suspend
(while keeping the wake_lock accounting as usual)
The d0i3 mode to use will be determined by the
underlying trans layer.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
d3 and d0i3 shouldn't be mutually exclusive. Set supported
wowlan triggers by looking for each of them, and check
on suspend/resume which flow should be used ("any" trigger
is supported by d0i3, and all the others by d3)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement the ref/unref trans ops and track both tx and
host command queues (and hold references while they
are not empty).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to add the offset. The type of the generic
memory dump will let the parser know that this is SRAM.
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of adding a dump type for each type of memory, change
the SMEM type to be a general purpose memory dump. Add the
type of the memory and its offset in the device in the dump
itself. This will allow an external parser to know where
this memory came from.
Note that since this type isn't really in use yet, this is
not a real problem.
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In NICs that have SMEM - add its content to the dump data
for later debug.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
nvm_file in family 8000 B step and A step differ. This means
that the driver should support 2 file name as default.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case the rate mask for one of the modulations was zero the
max rate idx for that modulation was set to 32 (BITS_PER_LONG).
This is bad as it would later lead to an out of bounds access
to the expected tpt table. In most cases there was no real effect
as the expected tpt was set to 0 and this led to avoiding the
modulation effectively.
Fix the out of bounds access and explicitly skip the modulation
in case there's no rate allowed in it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Clear the thermal throttling values when entering CT-kill, since
everything will be reinitialized anyway when we exit CT-kill.
Additionally, clear the dynamic_smps value in the initialization
funciton, for consistency.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The HW step member was left out of the core dump information. Fix this.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware is able to compensate the rssi when we hear
the frame on a different channel.
This is true for an offset up to 3 channels.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to collect the logs even if the firmware hasn't
crashed. Of course, crashing the firmware is an option, but
this is easier and nicer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the driver is unload, the Manageability Engine should
know about that - send an event to inform it about this
event.
Reviewed-by: Reuven Borok <reuven.borok@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: Moshe Harel <moshe.harel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The allocation of the DCCM between the data and the stack
can theoretically change without notice to the driver, but
the total size is HW-fixed. Since the stack CCM (runtime
stack) has also data important to the FW - this patch allows
pulling the whole DCCM in one piece and adds it to the dump
data.
If the size isn't known - just use the data part of the
DCCM as it appears in the FW TLVs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The module version "in-tree:" or "in-tree:d" is useless; there
should be better (functional) ways to detect whether debugging
is enabled and other than that the version says nothing.
Therefore remove the driver version completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For linux-3.18.0
The driver lacks pci_disable_device in error handling code of
ne2k_pci_init_one, so the device enabled by pci_enable_device is not
disabled when errors occur.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __bond_release_one(), when the interface is not a slave or not a slave of
"this" master, it log error message.
The message actually should be a debug message matching what bond_enslave()
does.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable that driver because Wireless Extensions is now disabled by default.
o Mika fixed brcmfmac not to crash when platform data is not populated
o Emmanuel provided few fixes to iwlwifi, he says:
"I have here new device IDs and a fix for double free bug I
introduced. I also fix an issue with the RFKILL interrupt - the HW
needs us to ACK the interrupt again after we reset it. Liad fixes an
issue with the firmware debugging infrastructure. While working on
torture scenarios of firmware restarts, Eliad found an issue which
he fixed."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUnUpQAAoJEG4XJFUm622bcoUIAISxktWxN6NOIrdQTcnm0fNz
AQZpCOlry0FNmEFSRJkcsNOD1Hv62iZqtSnwKQOOFMi8Rav9W+MIw0M16ieWsBTb
tt5PQjWH4KeAU64BmWsvtStRSRQf0xO7mR3ZlW6gD1rpwxtAggWxzF7hc61wYj0p
TOfbUuCvXLHWsc1YI/Ec9nfkVmEqWyzw4duuGh2lpOoEpAJz3BE0W10l5e5KMLK6
o/YiA3nk52jboTt0QZ8NbGCYAvXRhShI5CI5N9IHLm3pvJv1zNTv8JPUw38bH385
+IuP2s4bp6wDno75R/kWfYBppKXoOFrINFpU/7p9lhUF50qVoUmFfAFYPzWI2WI=
=aYZX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2014-12-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
o Paul made a Kconfig dependency fix to ipw2200, it was not possible to
enable that driver because Wireless Extensions is now disabled by default.
o Mika fixed brcmfmac not to crash when platform data is not populated
o Emmanuel provided few fixes to iwlwifi, he says:
"I have here new device IDs and a fix for double free bug I
introduced. I also fix an issue with the RFKILL interrupt - the HW
needs us to ACK the interrupt again after we reset it. Liad fixes an
issue with the firmware debugging infrastructure. While working on
torture scenarios of firmware restarts, Eliad found an issue which
he fixed."
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second init_completion call should be a reinit_completion here.
patch is against 3.18.0 linux-next
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This property is no longer used in the code yet the code looks for it in the device tree.
It does not cause an error if it's not in the tree.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic config_init callback also for KSZ8021 and KSZ8031.
This has been avoided this far due to commit b838b4aced ("phy/micrel:
KSZ8031RNL RMII clock reconfiguration bug"), which claims that the PHY
becomes unresponsive if the broadcast-disable flag is set before
configuring the clock mode.
Turns out that the problem seemingly worked-around by the above
mentioned commit was really due to a hardware-configuration issue, where
the PHY was in fact strapped to address 3 rather than 0.
Tested-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tpc entry to ath9k debugfs in order to enable/disable hw TPC
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable hw TPC by default on AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl8723be_phy_get_txpower_level() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl92ee_get_available_desc() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With this change, all of the drivers now use the common routine. As this
driver has VHT capability, an additional parameter is needed, thus all the
drivers had to be modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code uses macros to determine the parameters that are passed to the
rate setting routine. A simpler method is implemented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code uses macros to determine the parameters that are passed to the
rate setting routine. A simpler method is implemented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device RTL8821AE is the first if the rtlwifi devices to implement 802.11ac
capability. As a result, VHT rate descriptors are needed. In addition, the
driver is converted to use the descriptors in rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This common set of rate descriptors is renamed to be DESC_RATExx.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is also converted to use the rate-mapping code in the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver duplicates a routine found in the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver currently has its owm version of this routine that duplicates
a routine in rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Four of the drivers (92ce, 92cu, 92de, and 92se) supply an argument to the
rate-mapping routine that is never used, thus it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes match those of the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These changes were found in the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch applies changes found in the latest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change helps the device maintain a connection.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two of the macros that control power sequencing have values to be set that
contain bits that are not covered by the associated mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing method for loading both normal and WOWLAN firmware for the
device duplicates a lot of code. This solution is much cleaner.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The minimum number of pulses per burst on FCC radar type 5 is 1.
Use this number for correct radar detection.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory allocated by kmemdup() in rsi_load_ta_instructions() is leaked.
But duplication of firmware data here is useless,
so the patch removes kmemdup() at all.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the function rtl92d_set_fw_pwrmode_cmd() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver looks for pdata->oob_irq_supported to find out if wowl can be
supported. However, not all platforms populate pdata in which case we crash
the kernel because of NULL pointer dereference.
Fixes: 330b4e4be9 ("brcmfmac: Add wowl support for SDIO devices.")
Reported-by: Christophe Prigent <christophe.prigent@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 24a0aa212e ("cfg80211: make WEXT compatibility unselectable")
made it impossible to depend on CFG80211_WEXT. It does still allow to
select that symbol. (Yes, the commit summary is confusing.)
So make IPW2200 select CFG80211_WEXT, so that the ipw2200 driver can be
enabled in config again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of error vxlan_xmit_one() can free already freed skb.
Also fixes memory leak of dst-entry.
Fixes: acbf74a763 ("vxlan: Refactor vxlan driver to make use
of the common UDP tunnel functions").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phymode should use 11b only if NO_OFDM flags is set.
Hence check up channel flag for NO_OFDM and set to
11b.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Assoc peer command contain information about NSS.
When we will get IEEE80211_RC_NSS_CHANGED we should
also send (re) assoc peer command to be sure firmware
will know about it and RC will work correctly.
This was found during code review.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix TX problem when IBSS used in HT mode.
Before we used 6Mbps all the time for TX direction.
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Thermal cooling device support is added to control the temperature
by throttling the data transmission for the given duration. Throttling
is done using hw MAC quiet time setting. Period, duration and offset
from TBTT can be set up to quiet the MAC transmits for the required duty
cycle (% of quiet duration). The thermal device allows user to configure
duty cycle.
The quiet params are derived as follows.
period = max(25TU, beacon interval / number of bss)
duration = period * duty cycle / 100
Quiet mode can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI support to send pdev_set_quiet_mode command to target.
This will be used for thermal mitigation purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware uses bitmask in wmi_resource_config to configure
10.2 firmware features like airtime fairness and rx batch mode instead
of maintaining separete bool entry. This allows new features that can be
configure during init time without breaking backward compatibility.
kvalo: use WMI op version, bump up FW API to 4 to not break older versions of
ath10k
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The internal firmware version doesn't tell much to the user, it's more
informative to use that field to print the wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ATH10K_FW_FEATURE_WMI_10X should not be used for anymore as that's
now deprecated, instead use wmi op version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to manage firmware differences, we should not use
ATH10K_FW_FEATURE_WMI_10X outside ath10k_core_init_firmware_features(). To
achieve that create new field ar->max_num_vdevs and set it based on wmi op
version.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Decode and display Port Type and Module Type for ethtool get_settings() call
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit d75b1ade56 (net: less
interrupt masking in NAPI) breaks caif.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers caif tries to do a last-ditch check and if there is
more work it will call napi_schedule and then immediately process
some of this new work. Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in caif.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
iowrite32() will byteswap it's argument on big endian archs.
iowrite32be() will byteswap on little endian archs.
Since we don't want to do this unnecessary byteswap on the fast path,
doorbell is stored in the NIC's native endianness. Using the right
iowrite() according to the arch endianness.
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: David Laight <david.laight@aculab.com>
Fixes: 6a4e812 ("net/mlx4_en: Avoid calling bswap in tx fast path")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For linux-3.18.0
The driver lacks netif_napi_del in the normal path and error path
to match the call of netif_napi_add in rtl8139_init_one.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For linux-3.18.0
When pci_request_regions is failed in rtl8139_init_board, pci_disable_device
is not called to disable the device which are enabled by pci_enable_device,
because of disable_dev_on_err is not assigned 1.
This patch fix this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The s6000 Xtensa support has been removed from the kernel in
4006e565e1. There are no other chips using this driver.
While the Mentor/Alcatel PE-MCXMAC IP core is also used in other
designs (Freescale Gianfar/UCC, QLogic NetXen, Solarflare, Agere
ET-1310, Netlogic XLR/XLS), none of these use this driver as it
heavily depends on the s6000 DMA engine. In fact, there is no
code sharing across any of the aforementioned devices.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the function port_cfg_dis_learn() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Please queue for -stable.
Reported-by: Nils Holland <nholland@tisys.org>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changed names are union fields with the same size, so the existing code
still works. But, we now update these variables to the correct names.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit d75b1ade56 (net: less
interrupt masking in NAPI) breaks virtio_net in an insidious way.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers virtio_net tries to do a last-ditch check and if
there is more work it will call napi_schedule and then immediately
process some of this new work. Should the entire budget be consumed
while processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in virtio_net.
The worst part of this bug is that the list corruption causes other
napi users to be moved off-list. In my case I was chasing a stall
in IPsec (IPsec uses netif_rx) and I only belatedly realised that it
was virtio_net which caused the stall even though the virtio_net
poll was still functioning perfectly after IPsec stalled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both stmmac_open() and stmmac_resume() call stmmac_hw_setup(), and
stmmac_hw_setup() call stmmac_init_ptp() unconditionally. However, only
stmmac_release() calls stmmac_release_ptp(). Since stmmac_suspend()
doesn't call stmmac_release_ptp(), stmmac_resume() also needn't call
stmmac_init_ptp().
This patch also fix a "scheduling while atomic" problem when resume
from suspend/hibernation. Because stmmac_init_ptp() will trigger
scheduling while stmmac_resume() hold a spinlock.
Callgraph of "scheduling while atomic":
stmmac_resume() --> stmmac_hw_setup() --> stmmac_init_ptp() -->
stmmac_ptp_register() --> ptp_clock_register() --> device_create() -->
device_create_groups_vargs() --> device_add() --> devtmpfs_create_node()
--> wait_for_common() --> schedule_timeout() --> __schedule()
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Binderman reports that the conditions in the first loop
are the wrong way around - checking the array contents before
the size.
Instead of leaving the empty loop there and reordering the two
checks unify it into a single loop that skips over non-matches
and exits after the first match.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I also fix an issue with the RFKILL interrupt - the HW needs us to ACK
the interrupt again after we reset it.
Liad fixes an issue with the firmware debugging infrastructure.
While working on torture scenarios of firmware restarts, Eliad found an
issue which he fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1yv
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-for-kalle-2014-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
I have here new device IDs and a fix for double free bug I introduced.
I also fix an issue with the RFKILL interrupt - the HW needs us to ACK
the interrupt again after we reset it.
Liad fixes an issue with the firmware debugging infrastructure.
While working on torture scenarios of firmware restarts, Eliad found an
issue which he fixed.
when skb_gso_segment returns error, the original skb should be freed
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- On-demand paging support in core midlayer and mlx5 driver. This lets
userspace create non-pinned memory regions and have the adapter HW
trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MCO9
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.19:
- On-demand paging support in core midlayer and mlx5 driver. This
lets userspace create non-pinned memory regions and have the
adapter HW trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (56 commits)
IB/mlx5: Implement on demand paging by adding support for MMU notifiers
IB/mlx5: Add support for RDMA read/write responder page faults
IB/mlx5: Handle page faults
IB/mlx5: Page faults handling infrastructure
IB/mlx5: Add mlx5_ib_update_mtt to update page tables after creation
IB/mlx5: Changes in memory region creation to support on-demand paging
IB/mlx5: Implement the ODP capability query verb
mlx5_core: Add support for page faults events and low level handling
mlx5_core: Re-add MLX5_DEV_CAP_FLAG_ON_DMND_PG flag
IB/srp: Allow newline separator for connection string
IB/core: Implement support for MMU notifiers regarding on demand paging regions
IB/core: Add support for on demand paging regions
IB/core: Add flags for on demand paging support
IB/core: Add support for extended query device caps
IB/mlx5: Add function to read WQE from user-space
IB/core: Add umem function to read data from user-space
IB/core: Replace ib_umem's offset field with a full address
IB/mlx5: Enhance UMR support to allow partial page table update
IB/mlx5: Remove per-MR pas and dma pointers
RDMA/ocrdma: Always resolve destination mac from GRH for UD QPs
...
This version check allows the driver to only work with v=1 hardware
however there is no driver-facing difference with newer versions
(confirmed by Atmel FAEs) so this check needlessly prevents the driver
from being used with radios now in production.
Tested on AT86RF212B radio (which came up as v=3).
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver was reading the PART_NUM register for both the part number
(type of device) and the part version, the version is actually in
register 0x1D, VERSION_NUM. I believe that this was a copy-paste error.
Tested on AT86RF212B where the part is detected to be the expected part
number (0x07) and version (0x03 on mine).
Signed-off-by: Andrey Yurovsky <andrey@snupi.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The attribute extra_tx_headroom should already be zero.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the context pointer to the parameter given one inside
function at86rf230_async_state_change_start. This could occur problem if
context isn't pointed to lp->state.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch makes the at86rf230_async_error inline. This function is
small enough to handle inline.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes an unnecessary if branch inside the tx complete
handler.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <s.schmidt@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC: Alan Ott <alan@signal11.us>
Signed-off-by: Stefan Schmidt <s.schmidt@samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the default cca setting after device reset for at86rf230
driver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current cca setting handle is a driver specific call. We need to
introduce some 802.15.4 specific layer and mapping 802.15.4 cca modes to
driver specific ones inside the 802.15.4 driver. This patch will add
such 802.15.4 layer and mapping the cca settings to driver specific ones.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An earlier commit to resolve an issue with encapsulation offloads missed
setting a bit in the outer netdev features flag. This results in loss of TSO
feature on a VxLAN interface.
Fixes: 630f4b70 ("Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc96f648df (xen-netback: make
feature-rx-notify mandatory) incorrectly assumed that there were no
frontends in use that did not support this feature. But the frontend
driver in MiniOS does not and since this is used by (qemu) stubdoms,
these stopped working.
Netback sort of works as-is in this mode except:
- If there are no Rx requests and the internal Rx queue fills, only
the drain timeout will wake the thread. The default drain timeout
of 10 s would give unacceptable pauses.
- If an Rx stall was detected and the internal Rx queue is drained,
then the Rx thread would never wake.
Handle these two cases (when feature-rx-notify is disabled) by:
- Reducing the drain timeout to 30 ms.
- Disabling Rx stall detection.
Reported-by: John <jw@nuclearfallout.net>
Tested-by: John <jw@nuclearfallout.net>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QSA module was getting decoded as QSFP module in ethtool get settings, this
patch fixes it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.
Fixes: f6f6424ba7 ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit contains 2 fixes for the 128B CQE/EQE stride feaure.
Wei found that mlx4_QUERY_HCA function marked the wrong capability
in flags (64B CQE/EQE), when CQE/EQE stride feature was enabled.
Also added small fix in initial CQE ownership bit assignment, when CQE
is size is not default 32B.
Fixes: 77507aa24 (net/mlx4: Enable CQE/EQE stride support)
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do camera capture test on i.MX6q sabresd board, and save the capture data to
nfs rootfs. The command is:
gst-launch-1.0 -e imxv4l2src device=/dev/video1 num-buffers=2592000 ! tee name=t !
queue ! imxv4l2sink sync=false t. ! queue ! vpuenc ! queue ! mux. pulsesrc num-buffers=3720937
blocksize=4096 ! 'audio/x-raw, rate=44100, channels=2' ! queue ! imxmp3enc ! mpegaudioparse !
queue ! mux. qtmux name=mux ! filesink location=video_recording_long.mov
After about 10 hours running, there have net watchdog timeout kernel dump:
...
WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x2b4/0x2d8()
NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.24-01051-gdb840b7 #440
[<80014e6c>] (unwind_backtrace) from [<800118ac>] (show_stack+0x10/0x14)
[<800118ac>] (show_stack) from [<806ae3f0>] (dump_stack+0x78/0xc0)
[<806ae3f0>] (dump_stack) from [<8002b504>] (warn_slowpath_common+0x68/0x8c)
[<8002b504>] (warn_slowpath_common) from [<8002b558>] (warn_slowpath_fmt+0x30/0x40)
[<8002b558>] (warn_slowpath_fmt) from [<8055e0d4>] (dev_watchdog+0x2b4/0x2d8)
[<8055e0d4>] (dev_watchdog) from [<800352d8>] (call_timer_fn.isra.33+0x24/0x8c)
[<800352d8>] (call_timer_fn.isra.33) from [<800354c4>] (run_timer_softirq+0x184/0x220)
[<800354c4>] (run_timer_softirq) from [<8002f420>] (__do_softirq+0xc0/0x22c)
[<8002f420>] (__do_softirq) from [<8002f804>] (irq_exit+0xa8/0xf4)
[<8002f804>] (irq_exit) from [<8000ee5c>] (handle_IRQ+0x54/0xb4)
[<8000ee5c>] (handle_IRQ) from [<80008598>] (gic_handle_irq+0x28/0x5c)
[<80008598>] (gic_handle_irq) from [<800123c0>] (__irq_svc+0x40/0x74)
Exception stack(0x80d27f18 to 0x80d27f60)
7f00: 80d27f60 0000014c
7f20: 8858c60e 0000004d 884e4540 0000004d ab7250d0 80d34348 00000000 00000000
7f40: 00000001 00000000 00000017 80d27f60 800702a4 80476e6c 600f0013 ffffffff
[<800123c0>] (__irq_svc) from [<80476e6c>] (cpuidle_enter_state+0x50/0xe0)
[<80476e6c>] (cpuidle_enter_state) from [<80476fa8>] (cpuidle_idle_call+0xac/0x154)
[<80476fa8>] (cpuidle_idle_call) from [<8000f174>] (arch_cpu_idle+0x8/0x44)
[<8000f174>] (arch_cpu_idle) from [<80064c54>] (cpu_startup_entry+0x100/0x158)
[<80064c54>] (cpu_startup_entry) from [<80cd8a9c>] (start_kernel+0x304/0x368)
---[ end trace 09ebd32fb032f86d ]---
...
There might have a race in napi_schedule(), leaving interrupts disabled forever.
After these patch, the case still work more than 40 hours running.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d75b1ade56 (net: less interrupt
masking in NAPI) the napi instance is removed from the per-cpu list
prior to calling the n->poll(), and is only requeued if all of the
budget was used. This inadvertently broke netfront because netfront
does not use NAPI correctly.
If netfront had not used all of its budget it would do a final check
for any Rx responses and avoid calling napi_complete() if there were
more responses. It would still return under budget so it would never
be rescheduled. The final check would also not re-enable the Rx
interrupt.
Additionally, xenvif_poll() would also call napi_complete() /after/
enabling the interrupt. This resulted in a race between the
napi_complete() and the napi_schedule() in the interrupt handler. The
use of local_irq_save/restore() avoided by race iff the handler is
running on the same CPU but not if it was running on a different CPU.
Fix both of these by always calling napi_compete() if the budget was
not all used, and then calling napi_schedule() if the final checks
says there's more work.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-12-16
Please pull this batch of fixes intended for the 3.19 stream!
For the Bluetooth bits, Johan says:
"The patches consist of:
- Coccinelle warning fix
- hci_dev_lock/unlock fixes
- Fixes for pending mgmt command handling
- Fixes for properly following the force_lesc_support switch
- Fix for a Microsoft branded Broadcom adapter
- New device id for Atheros AR3012
- Fix for BR/EDR Secure Connections enabling"
Along with that...
Brian Norris avoids leaking some kernel memory contents via printk in brcmsmac.
Julia Lawall corrects some misspellings in a few drivers.
Larry Finger gives us one more rtlwifi fix to correct a porting oversight.
Wei Yongjun fixes a sparse warning in rtlwifi.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we get things like:
warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)
In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".
Signed-off-by: David S. Miller <davem@davemloft.net>
flags field in ifreq is only 16 bit wide, but
we read it as a 32 bit value.
If userspace doesn't zero-initialize unused fields,
this will lead to failures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware doesn't allow precise tx rate control so
P2P wasn't entirely spec compliant (it was using
CCK rates in some cases).
The only way to make sure firmware doesn't use CCK
rates is to have a vdev with P2P subtype used for
scanning and tx. This can be done via a special
dedicated P2P device interface support.
This also removes the ancient hack from ath10k in
favor of p2pdev.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per-vif bss_conf.ps should be used to configure
powersave.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting 0 ps timeout to firmware yields very poor
latency and traffic issues. This is the case when
multi-vif is active.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To comply with WMM-PS the device shouldn't wake up
with a NullFunc frame pair when tx-ing. Instead PM
bit on each tx frame should be used.
To make this work correctly firmware needs to be
told to use a different STA PS wake threshold when
u-APSD is enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some firmware revisions need peer phymode to be
specified as MODE_11B when associating as station
to a 11b AP. Otherwise they can starve other
stations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Setting fragmentation threshold has not been supported by
any of firmware versions, hence unregister the callback and
remove the function.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is no need to do the following:
select FIXED_PHY if NET_DSA_BCM_SF2=y, as this implies that we will not be
able to build and/or run the driver correctly when built as a module,
which is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()").
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if SYSTEMPORT=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()")
Fixes: a3862db2d3 ("net: systemport: hook SYSTEMPORT driver in the build")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do the following:
select FIXED_PHY if BCMGENET=y, as this implies that we will not be able
to build and/or run the driver correctly when built as a module, which
is no longer an issue since commit 37e9a69045 ("net: phy: export
fixed_phy_register()")
Fixes: b0ba512e225d ("net: bcmgenet: enable driver to work without device tree"
Fixes: bdaa53bde5 ("net: bcmgenet: hook into the build system")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add a handler function pointer in the mlx5_core_qp struct for page
fault events. Handle page fault events by calling the handler
function, if not NULL.
* Add on-demand paging capability query command.
* Export command for resuming QPs after page faults.
* Add various constants related to paging support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move check for DPDP out of the loop to make the code more readable.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The setting of this flag was missed in previous modifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Debug code prints the fifo name via custom dev_warn() wrappers. The
fifo_names array is only non-zero when debugging is manually enabled,
which is all well and good. However, it's *not* good that this array
uses zero-length arrays in the non-debug case, and so it doesn't
actually have any memory allocated to it. This means that as far as we
know, fifo_names[i] actually points to garbage memory.
I've seen this in my log:
[ 4601.205511] brcmsmac bcma0:1: wl0: brcms_c_d11hdrs_mac80211: �GeL txop exceeded phylen 137/256 dur 1602/1504
So let's give this array space enough to fill it with a NULL byte.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list@broadcom.com
Cc: netdev@vger.kernel.org
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes the following sparse warning:
drivers/net/wireless/rtlwifi/rtl8192cu/hw.c:1595:6: warning:
symbol 'usb_cmd_send_packet' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace a misspelled function name by %s and then __func__.
8821 was written as 8812.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside macb_probe(), when devm_request_irq() fails on queue q, there is no need
to call devm_free_irq() on queues 0..q-1 because the managed device resources
are released later when calling free_netdev().
Also removing devm_free_irq() call from macb_remove() for the same reason.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix a bug introduced by the multiqueue support patch:
"net/macb: add TX multiqueue support for gem"
the "bp" pointer to the netdev private data was dereferenced and used after the
associated memory had been freed by calling free_netdev().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_OF is not set:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c: In function ‘sti_dwmac_parse_data’:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:318: warning: ‘rs’ is used uninitialized in this function
of_property_read_string() will return -ENOSYS in this case, and rs will
be an uninitialized pointer.
While the fallback clock selection is already selected correctly in this
case, the string comparisons should be skipped too, else the system will
crash while dereferencing the uninitialized pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If GPIOLIB=n the following build errors occur:
drivers/net/ethernet/smsc/smc91x.c: In function 'try_toggle_control_gpio':
drivers/net/ethernet/smsc/smc91x.c:2204:2: error: implicit declaration of function 'devm_gpiod_get_index' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2204:7: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/net/ethernet/smsc/smc91x.c:2213:2: error: implicit declaration of function 'gpiod_direction_output' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2216:3: error: implicit declaration of function 'devm_gpiod_put' [-Werror=implicit-function-declaration]
drivers/net/ethernet/smsc/smc91x.c:2222:2: error: implicit declaration of function 'gpiod_set_value_cansleep' [-Werror=implicit-function-declaration]
Fix this by letting the driver depend on GPIOLIB if OF is selected.
Fixes: 7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be future-proof and for better readability the time comparisons are
modified to use time_before, time_after, and time_after_eq instead of
plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support asymmetric EQ allocations, we should query the device
capabilities prior to enabling SRIOV. As a side effect of adding that,
we are dumping the PF device capabilities twice. Avoid that by moving
the printing into a helper function which is called once.
Fixes: 7ae0e400cd ('net/mlx4_core: Flexible (asymmetric) allocation of
EQs and MSI-X vectors for PF/VFs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mlx4_load_one has a memory leak as it always allocates
dev_cap, but frees it only on error.
In addition, even if VFs exist when mlx4_load_one is called,
we still need to notify probed VFs that we're loading (by
incrementing pf_loading).
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few device IDs were added, reflect this change in the
driver.
Cc; <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the very unlikely case in which no firmware could be,
found. the same pointer was freed twice. Fix that.
Fixes: 490fefebb6 ("iwlwifi: define the .ucode file format for debug")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.
Fixes: 522713c81e ("iwlwifi: pcie: properly reset the device")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
On stop(), we already cleared our internal state,
and the restart_complete() callback won't be
called, so simply clear the IN_HW_RESTART flag.
Keeping the flag might result in invalid state
on the next start(), preventing the driver starting
properly.
Additionally, don't take IWL_MVM_REF_UCODE_DOWN on stop()
if hw restart was requested, as the ref was already
taken in this case.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Pull another networking update from David Miller:
"Small follow-up to the main merge pull from the other day:
1) Alexander Duyck's DMA memory barrier patch set.
2) cxgb4 driver fixes from Karen Xie.
3) Add missing export of fixed_phy_register() to modules, from Mark
Salter.
4) DSA bug fixes from Florian Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
net/macb: add TX multiqueue support for gem
linux/interrupt.h: remove the definition of unused tasklet_hi_enable
jme: replace calls to redundant function
net: ethernet: davicom: Allow to select DM9000 for nios2
net: ethernet: smsc: Allow to select SMC91X for nios2
cxgb4: Add support for QSA modules
libcxgbi: fix freeing skb prematurely
cxgb4i: use set_wr_txq() to set tx queues
cxgb4i: handle non-pdu-aligned rx data
cxgb4i: additional types of negative advice
cxgb4/cxgb4i: set the max. pdu length in firmware
cxgb4i: fix credit check for tx_data_wr
cxgb4i: fix tx immediate data credit check
net: phy: export fixed_phy_register()
fib_trie: Fix trie balancing issue if new node pushes down existing node
vlan: Add ability to always enable TSO/UFO
r8169:update rtl8168g pcie ephy parameter
net: dsa: bcm_sf2: force link for all fixed PHY devices
fm10k/igb/ixgbe: Use dma_rmb on Rx descriptor reads
r8169: Use dma_rmb() and dma_wmb() for DescOwn checks
...
Pull sparc update from David Miller:
"Not a lot of stuff this time around, mostly bug fixing:
- Fix alignment of 32-bit crosscall datastructure on Leon, from
Andreas Larsson.
- Several fixes to the virtual disk driver on sparc64 by Dwight
Engen, including handling resets of the service domain properly"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sunvdc: reconnect ldc after vds service domain restarts
sparc/ldc: create separate ldc_unbind from ldc_free
vio: create routines for inc,dec vio dring indexes
sunvdc: fix module unload/reload
sparc32, leon: Align ccall_info to prevent unaligned traps on crosscall
gem devices designed with multiqueue CANNOT work without this patch.
When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.
For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.
Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.
Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).
Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.
Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.
When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to tasklet_hi_enable are replaced by calls to
tasklet_enable since the 2 functions are redundant.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is present on older revisions of the DE2 development kit.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware 1.12.25.0 added support for QSA module, adding the driver code for it.
Also fixes some ethtool get settings for other module types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programs the firmware of the maximum outgoing iscsi pdu length per connection.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the bcmgenet driver as module, I get:
ERROR: "fixed_phy_register" [drivers/net/ethernet/broadcom/genet/genet.ko] undefined!
commit b0ba512e225d72 ("net: bcmgenet: enable driver to work without device
tree") which added a call to fixed_phy_register. But fixed_phy_register
needs to be exported if used from a module.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move IEEE80211_TX_CTL_PS_RESPONSE to info->control.flags since
this is used only in the TX path (by ath9k). This frees up
a bit which can be used for other purposes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both sunvdc and sunvnet implemented distinct functionality for incrementing
and decrementing dring indexes. Create common functions for use by both
from the sunvnet versions, which were chosen since they will still work
correctly in case a non power of two ring size is used.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
