Both raid1 and raid10 share common resync
block size and page count, so move them into md.h.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
All bio_add_page() is for adding one page into resync bio,
which is big enough to hold RESYNC_PAGES pages, and
the current bio_add_page() doesn't check queue limit any more,
so it won't fail at all.
remove unused label (shaohua)
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Previously, we clone both bio and repl_bio in raid10_write_request,
then add the cloned bio to plug->pending or conf->pending_bio_list
based on plug or not, and most of the logics are same for the two
conditions.
So introduce raid10_write_one_disk for it, and use replacement parameter
to distinguish the difference. No functional changes in the patch.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid10 currently repurposes bi_phys_segments on each
incoming bio to count how many r10bio was used to encode the
request.
We need to know when the number of attached r10bio reaches
zero to:
1/ call bio_endio() when all IO on the bio is finished
2/ decrement ->nr_pending so that resync IO can proceed.
Now that the bio has its own __bi_remaining counter, that
can be used instead. We can call bio_inc_remaining to
increment the counter and call bio_endio() every time an
r10bio completes, rather than only when bi_phys_segments
reaches zero.
This addresses point 1, but not point 2. bio_endio()
doesn't (and cannot) report when the last r10bio has
finished, so a different approach is needed.
So: instead of counting bios in ->nr_pending, count r10bios.
i.e. every time we attach a bio, increment nr_pending.
Every time an r10bio completes, decrement nr_pending.
Normally we only increment nr_pending after first checking
that ->barrier is zero, or some other non-trivial tests and
possible waiting. When attaching multiple r10bios to a bio,
we only need the tests and the waiting once. After the
first increment, subsequent increments can happen
unconditionally as they are really all part of the one
request.
So introduce inc_pending() which can be used when we know
that nr_pending is already elevated.
Note that this fixes a bug. freeze_array() contains the line
atomic_read(&conf->nr_pending) == conf->nr_queued+extra,
which implies that the units for ->nr_pending, ->nr_queued and extra
are the same.
->nr_queue and extra count r10_bios, but prior to this patch,
->nr_pending counted bios. If a bio ever resulted in multiple
r10_bios (due to bad blocks), freeze_array() would not work correctly.
Now it does.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When raid1 or raid10 find they will need to allocate a new
r1bio/r10bio, in order to work around a known bad block, they
account for the allocation well before the allocation is
made. This separation makes the correctness less obvious
and requires comments.
The accounting needs to be a little before: before the first
rXbio is submitted, but that is all.
So move the accounting down to where it makes more sense.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD fixes from Shaohua Li:
- fix a parity calculation bug of raid5 cache by Song
- fix a potential deadlock issue by me
- fix two endian issues by Jason
- fix a disk limitation issue by Neil
- other small fixes and cleanup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid1: fix a trivial typo in comments
md/r5cache: fix set_syndrome_sources() for data in cache
md: fix incorrect use of lexx_to_cpu in does_sb_need_changing
md: fix super_offset endianness in super_1_rdev_size_change
md/raid1/10: fix potential deadlock
md: don't impose the MD_SB_DISKS limit on arrays without metadata.
md: move funcs from pers->resize to update_size
md-cluster: remove useless memset from gather_all_resync_info
md-cluster: free md_cluster_info if node leave cluster
md: delete dead code
md/raid10: submit bio directly to replacement disk
Commit 79bd99596b ("blk: improve order of bio handling in generic_make_request()")
changed current->bio_list so that it did not contain *all* of the
queued bios, but only those submitted by the currently running
make_request_fn.
There are two places which walk the list and requeue selected bios,
and others that check if the list is empty. These are no longer
correct.
So redefine current->bio_list to point to an array of two lists, which
contain all queued bios, and adjust various code to test or walk both
lists.
Signed-off-by: NeilBrown <neilb@suse.com>
Fixes: 79bd99596b ("blk: improve order of bio handling in generic_make_request()")
Signed-off-by: Jens Axboe <axboe@fb.com>
Neil Brown pointed out a potential deadlock in raid 10 code with
bio_split/chain. The raid1 code could have the same issue, but recent
barrier rework makes it less likely to happen. The deadlock happens in
below sequence:
1. generic_make_request(bio), this will set current->bio_list
2. raid10_make_request will split bio to bio1 and bio2
3. __make_request(bio1), wait_barrer, add underlayer disk bio to
current->bio_list
4. __make_request(bio2), wait_barrer
If raise_barrier happens between 3 & 4, since wait_barrier runs at 3,
raise_barrier waits for IO completion from 3. And since raise_barrier
sets barrier, 4 waits for raise_barrier. But IO from 3 can't be
dispatched because raid10_make_request() doesn't finished yet.
The solution is to adjust the IO ordering. Quotes from Neil:
"
It is much safer to:
if (need to split) {
split = bio_split(bio, ...)
bio_chain(...)
make_request_fn(split);
generic_make_request(bio);
} else
make_request_fn(mddev, bio);
This way we first process the initial section of the bio (in 'split')
which will queue some requests to the underlying devices. These
requests will be queued in generic_make_request.
Then we queue the remainder of the bio, which will be added to the end
of the generic_make_request queue.
Then we return.
generic_make_request() will pop the lower-level device requests off the
queue and handle them first. Then it will process the remainder
of the original bio once the first section has been fully processed.
"
Note, this only happens in read path. In write path, the bio is flushed to
underlaying disks either by blk flush (from schedule) or offladed to raid1/10d.
It's queued in current->bio_list.
Cc: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org (v3.14+, only the raid10 part)
Suggested-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Shaohua Li <shli@fb.com>
raid1_resize and raid5_resize should also check the
mddev->queue if run underneath dm-raid.
And both set_capacity and revalidate_disk are used in
pers->resize such as raid1, raid10 and raid5. So
move them from personality file to common code.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit 57c67df(md/raid10: submit IO from originating thread instead of
md thread) submits bio directly for normal disks but not for replacement
disks. There is no point we shouldn't do this for replacement disks.
Cc: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Pull md updates from Shaohua Li:
"Mainly fixes bugs and improves performance:
- Improve scalability for raid1 from Coly
- Improve raid5-cache read performance, disk efficiency and IO
pattern from Song and me
- Fix a race condition of disk hotplug for linear from Coly
- A few cleanup patches from Ming and Byungchul
- Fix a memory leak from Neil
- Fix WRITE SAME IO failure from me
- Add doc for raid5-cache from me"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (23 commits)
md/raid1: fix write behind issues introduced by bio_clone_bioset_partial
md/raid1: handle flush request correctly
md/linear: shutup lockdep warnning
md/raid1: fix a use-after-free bug
RAID1: avoid unnecessary spin locks in I/O barrier code
RAID1: a new I/O barrier implementation to remove resync window
md/raid5: Don't reinvent the wheel but use existing llist API
md: fast clone bio in bio_clone_mddev()
md: remove unnecessary check on mddev
md/raid1: use bio_clone_bioset_partial() in case of write behind
md: fail if mddev->bio_set can't be created
block: introduce bio_clone_bioset_partial()
md: disable WRITE SAME if it fails in underlayer disks
md/raid5-cache: exclude reclaiming stripes in reclaim check
md/raid5-cache: stripe reclaim only counts valid stripes
MD: add doc for raid5-cache
Documentation: move MD related doc into a separate dir
md: ensure md devices are freed before module is unloaded.
md/r5cache: improve journal device efficiency
md/r5cache: enable chunk_aligned_read with write back cache
...
Firstly bio_clone_mddev() is used in raid normal I/O and isn't
in resync I/O path.
Secondly all the direct access to bvec table in raid happens on
resync I/O except for write behind of raid1, in which we still
use bio_clone() for allocating new bvec table.
So this patch replaces bio_clone() with bio_clone_fast()
in bio_clone_mddev().
Also kill bio_clone_mddev() and call bio_clone_fast() directly, as
suggested by Christoph Hellwig.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Shaohua Li <shli@fb.com>
We will want to have struct backing_dev_info allocated separately from
struct request_queue. As the first step add pointer to backing_dev_info
to request_queue and convert all users touching it. No functional
changes in this patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Refactor raid10_make_request into seperate read and write functions to
clean up the code.
Shaohua: add the recovery check back to read path
Signed-off-by: Robert LeBlanc <robert@leblancnet.us>
Signed-off-by: Shaohua Li <shli@fb.com>
The mddev->flags are used for different purposes. There are a lot of
places we check/change the flags without masking unrelated flags, we
could check/change unrelated flags. These usage are most for superblock
write, so spearate superblock related flags. This should make the code
clearer and also fix real bugs.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When writing to a fastfail device, we use MD_FASTFAIL unless
it is the only device being written to. For
resync/recovery, assume there was a working device to read
from so always use MD_FASTFAIL.
If a write for resync/recovery fails, we just fail the
device - there is not much else to do.
If a normal write fails, but the device cannot be marked
Faulty (must be only one left), we queue for write error
handling which calls narrow_write_error() to write the block
synchronously without any failfast flags.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If a device is marked FailFast, and it is not the only
device we can read from, we mark the bio as MD_FAILFAST.
If this does fail-fast, we don't try read repair but just
allow failure.
If it was the last device, it doesn't get marked Faulty so
the retry happens on the same device - this time without
FAILFAST. A subsequent failure will not retry but will just
pass up the error.
During resync we may use FAILFAST requests, and on a failure
we will simply use the other device(s).
During recovery we will only use FAILFAST in the unusual
case were there are multiple places to read from - i.e. if
there are > 2 devices. If we get a failure we will fail the
device and complete the resync/recovery with remaining
devices.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This can only be supported on personalities which ensure
that md_error() never causes an array to enter the 'failed'
state. i.e. if marking a device Faulty would cause some
data to be inaccessible, the device is status is left as
non-Faulty. This is true for RAID1 and RAID10.
If we get a failure writing metadata but the device doesn't
fail, it must be the last device so we re-write without
FAILFAST to improve chance of success. We also flag the
device as LastDev so that future metadata updates don't
waste time on failfast writes.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Both raid1 and raid10 will sometimes delay handling an IO request,
such as when resync is happening or there are too many requests queued.
Add some blktrace messsages so we can see when that is happening when
looking for performance artefacts.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The block tracing infrastructure (accessed with blktrace/blkparse)
supports the tracing of mapping bios from one device to another.
This is currently used when a bio in a partition is mapped to the
whole device, when bios are mapped by dm, and for mapping in md/raid5.
Other md personalities do not include this tracing yet, so add it.
When a read-error is detected we redirect the request to a different device.
This could justifiably be seen as a new mapping for the originial bio,
or a secondary mapping for the bio that errors. This patch uses
the second option.
When md is used under dm-raid, the mappings are not traced as we do
not have access to the block device number of the parent.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
When writing to an array with a bitmap enabled, the writes are grouped
in batches which are preceded by an update to the bitmap.
It is quite likely if that a drive develops a problem which is not
media related, that the bitmap write will be the first to report an
error and cause the device to be marked faulty (as the bitmap write is
at the start of a batch).
In this case, there is point submiting the subsequent writes to the
failed device - that just wastes times.
So re-check the Faulty state of a device before submitting a
delayed write.
This requires that we keep the 'rdev', rather than the 'bdev' in the
bio, then swap in the bdev just before final submission.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This is the counterpart of raid10 fix. If a write error occurs, raid10
will try to rewrite the bio in small chunk size. If the rewrite fails,
raid10 will record the error in bad block. narrow_write_error will
always use WRITE for the bio, but actually it could be a discard. Since
discard bio hasn't payload, write the bio will cause different issues.
But discard error isn't fatal, we can safely ignore it. This is what
this patch does.
This issue should exist since discard is added, but only exposed with
recent arbitrary bio size feature.
Cc: Sitsofe Wheeler <sitsofe@gmail.com>
Cc: stable@vger.kernel.org (v3.6)
Signed-off-by: Shaohua Li <shli@fb.com>
Pull MD fixes from Shaohua Li:
"This includes several bug fixes:
- Alexey Obitotskiy fixed a hang for faulty raid5 array with external
management
- Song Liu fixed two raid5 journal related bugs
- Tomasz Majchrzak fixed a bad block recording issue and an
accounting issue for raid10
- ZhengYuan Liu fixed an accounting issue for raid5
- I fixed a potential race condition and memory leak with DIF/DIX
enabled
- other trival fixes"
* tag 'md/4.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid5: avoid unnecessary bio data set
raid5: fix memory leak of bio integrity data
raid10: record correct address of bad block
md-cluster: fix error return code in join()
r5cache: set MD_JOURNAL_CLEAN correctly
md: don't print the same repeated messages about delayed sync operation
md: remove obsolete ret in md_start_sync
md: do not count journal as spare in GET_ARRAY_INFO
md: Prevent IO hold during accessing to faulty raid5 array
MD: hold mddev lock to change bitmap location
raid5: fix incorrectly counter of conf->empty_inactive_list_nr
raid10: increment write counter after bio is split
For failed write request record block address on a device, not block
address in an array.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
md pending write counter must be incremented after bio is split,
otherwise it gets decremented too many times in end bio callback and
becomes negative.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Reviewed-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
RAID10 random read performance is lower than expected due to excessive spinlock
utilisation which is required mostly for rebuild/resync. Simplify allow_barrier
as it's in IO path and encounters a lot of unnecessary congestion.
As lower_barrier just takes a lock in order to decrement a counter, convert
counter (nr_pending) into atomic variable and remove the spin lock. There is
also a congestion for wake_up (it uses lock internally) so call it only when
it's really needed. As wake_up is not called constantly anymore, ensure process
waiting to raise a barrier is notified when there are no more waiting IOs.
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The md code stores the exact time of the last error in the
last_read_error variable using a timespec structure. It only
ever uses the seconds portion of that though, so we can
use a scalar for it.
There won't be an overflow in 2038 here, because it already
used monotonic time and 32-bit is enough for that, but I've
decided to use time64_t for consistency in the conversion.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Every time a device is removed with ->hot_remove_disk() a synchronize_rcu() call is made
which can delay several milliseconds in some case.
If lots of devices fail at once - as could happen with a large RAID10 where one set
of devices are removed all at once - these delays can add up to be very inconcenient.
As failure is not reversible we can check for that first, setting a
separate flag if it is found, and then all synchronize_rcu() once for
all the flagged devices. Then ->hot_remove_disk() function can skip the
synchronize_rcu() step if the flag is set.
fix build error(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
It is important that we never increment rdev->nr_pending on a Faulty
device as ->hot_remove_disk() assumes that once the Faulty flag is visible
no code will take a new reference.
Some places take a new reference after only check In_sync. This should
be safe as the two are changed together. However to make the code more
obviously safe, add checks for 'Faulty' as well.
Note: the actual rule is:
Never increment nr_pending if Faulty is set and Blocked is clear,
never clear Faulty, and never set Blocked without holding a reference
through nr_pending.
fix build error (Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
'tmp' is only ever used to extract 'tmp->rdev', so just use 'rdev' directly.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
rdev already holds conf->mirrors[d].rdev, so no need to load it again.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
Reshape isn't always suitably careful as in the past rdev couldn't be
removed during reshape. It can now, so add protection.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
Previously they could not become NULL during a resync/recovery/reshape either.
However when remove_and_add_spares() was added to hot_remove_disk(), that
changed.
So raid10_sync_request didn't previously need to protect rdev access,
but now it does.
Fix missed check(Shaohua)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
mirrors[].rdev can become NULL at any point unless:
- a counted reference is held
- ->reconfig_mutex is held, or
- rcu_read_lock() is held
raid10_status holds none of these. So add rcu_read_lock()
protection.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
If you have a raid10 with a replacement device that is resyncing -
e.g. after a crash before the replacement was complete - the write to
the replacement will increment nr_pending on the wrong device, which
will lead to strangeness.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Re-checking the faulty flag here brings no value.
The comment about "risk" refers to the risk that the device could
be in the process of being removed by ->hot_remove_disk().
However providing that the ->nr_pending count is incremented inside
an rcu_read_locked() region, there is no risk of that happening.
This is because the rdev pointer (in the personalities array) is set
to NULL before synchronize_rcu(), and ->nr_pending is tested
afterwards. If the rcu_read_locked region happens before the
synchronize_rcu(), the test will see that nr_pending has been incremented.
If it happens afterwards, the rdev pointer will be NULL so there is nothing
to increment.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
A performance drop of mkfs has been observed on RAID10 during resync
since commit 09314799e4 ("md: remove 'go_faster' option from
->sync_request()"). Resync sends so many IOs it slows down non-resync
IOs significantly (few times). Add a short delay to a resync. The
previous long sleep (1s) has proven unnecessary, even very short delay
brings performance right.
The change also applied to raid1. The problem has not been observed on
raid1, however it shares barriers code with raid10 so it might be an
issue for some setup too.
Suggested-by: NeilBrown <neilb@suse.com>
Link: http://lkml.kernel.org/r/20160609134555.GA9104@proton.igk.intel.com
Signed-off-by: Tomasz Majchrzak <tomasz.majchrzak@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have md
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Some code waits for a metadata update by:
1. flagging that it is needed (MD_CHANGE_DEVS or MD_CHANGE_CLEAN)
2. setting MD_CHANGE_PENDING and waking the management thread
3. waiting for MD_CHANGE_PENDING to be cleared
If the first two are done without locking, the code in md_update_sb()
which checks if it needs to repeat might test if an update is needed
before step 1, then clear MD_CHANGE_PENDING after step 2, resulting
in the wait returning early.
So make sure all places that set MD_CHANGE_PENDING are atomicial, and
bit_clear_unless (suggested by Neil) is introduced for the purpose.
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: <linux-kernel@vger.kernel.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
In case md runs underneath the dm-raid target, the mddev does not have
a request queue or gendisk, thus avoid accesses to it.
This patch adds two missing conditionals to the raid10 personality.
Signed-of-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
This is the raid10 counterpart of the bug fixed by Nate
(raid1: include bio_end_io_list in nr_queued to prevent freeze_array hang)
Fixes: 95af587e95(md/raid10: ensure device failure recorded before write request returns)
Cc: stable@vger.kernel.org (V4.3+)
Cc: Nate Dailey <nate.dailey@stratus.com>
Signed-off-by: Shaohua Li <shli@fb.com>
It is not safe for an integrity profile to be changed while i/o is
in-flight in the queue. Prevent adding new disks or otherwise online
spares to an array if the device has an incompatible integrity profile.
The original change to the blk_integrity_unregister implementation in
md, commmit c7bfced9a6 "md: suspend i/o during runtime
blk_integrity_unregister" introduced an immediate hang regression.
This policy of disallowing changes the integrity profile once one has
been established is shared with DM.
Here is an abbreviated log from a test run that:
1/ Creates a degraded raid1 with an integrity-enabled device (pmem0s) [ 59.076127]
2/ Tries to add an integrity-disabled device (pmem1m) [ 90.489209]
3/ Retries with an integrity-enabled device (pmem1s) [ 205.671277]
[ 59.076127] md/raid1:md0: active with 1 out of 2 mirrors
[ 59.078302] md: data integrity enabled on md0
[..]
[ 90.489209] md0: incompatible integrity profile for pmem1m
[..]
[ 205.671277] md: super_written gets error=-5
[ 205.677386] md/raid1:md0: Disk failure on pmem1m, disabling device.
[ 205.677386] md/raid1:md0: Operation continuing on 1 devices.
[ 205.683037] RAID1 conf printout:
[ 205.684699] --- wd:1 rd:2
[ 205.685972] disk 0, wo:0, o:1, dev:pmem0s
[ 205.687562] disk 1, wo:1, o:1, dev:pmem1s
[ 205.691717] md: recovery of RAID array md0
Fixes: c7bfced9a6 ("md: suspend i/o during runtime blk_integrity_unregister")
Cc: <stable@vger.kernel.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Reported-by: NeilBrown <neilb@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.com>
