The ETHTOOL_GLINKSETTINGS command is deprecating the ETHTOOL_GSET
command and likewise it shouldn't require the CAP_NET_ADMIN capability.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typical NAPI drivers use napi_consume_skb(skb) at TX completion time.
This put skb in a percpu special queue, napi_alloc_cache, to get bulk
frees.
It turns out the queue is not flushed and hits the NAPI_SKB_CACHE_SIZE
limit quite often, with skbs that were queued hundreds of usec earlier.
I measured this can take ~6000 nsec to perform one flush.
__kfree_skb_flush() can be called from two points right now :
1) From net_tx_action(), but only for skbs that were queued to
sd->completion_queue.
-> Irrelevant for NAPI drivers in normal operation.
2) From net_rx_action(), but only under high stress or if RPS/RFS has a
pending action.
This patch changes net_rx_action() to perform the flush in all cases and
after more urgent operations happened (like kicking remote CPUS for
RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from sk_filter_trim_cap().
eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).
Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This program type is similar to BPF_PROG_TYPE_SOCKET_FILTER, except that
it does not allow BPF_LD_[ABS|IND] instructions and hooks up the
bpf_skb_load_bytes() helper.
Programs of this type will be attached to cgroups for network filtering
and accounting.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.
We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.
Fixes: 968ad9da7e ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE")
Fixes: 310d9ad57a ("net: phy: Add downshift get/set support in Microsemi PHYs driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.
The supported modes: none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RT netlink, calcit() function should return the minimal size for
netlink dump message. This will make sure that dump message for every
network device can be stored.
Currently, rtnl_calcit() function doesn't account the size of header of
netlink message, this patch will fix it.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The threshold for OOM protection is too small for systems with large
number of CPUs. Applications report ENOBUFs on connect() every 10
minutes.
The problem is that the variable net->xfrm.flow_cache_gc_count is a
global counter while the variable fc->high_watermark is a per-CPU
constant. Take the number of CPUs into account as well.
Fixes: 6ad3122a08 ("flowcache: Avoid OOM condition under preasure")
Reported-by: Lukáš Koldrt <lk@excello.cz>
Tested-by: Jan Hejl <jh@excello.cz>
Signed-off-by: Miroslav Urbanek <mu@miroslavurbanek.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Andre Noll reported panics after my recent fix (commit 34fad54c25
"net: __skb_flow_dissect() must cap its return value")
After some more headaches, Alexander root caused the problem to
init_default_flow_dissectors() being called too late, in case
a network driver like IGB is not a module and receives DHCP message
very early.
Fix is to call init_default_flow_dissectors() much earlier,
as it is a core infrastructure and does not depend on another
kernel service.
Fixes: 06635a35d1 ("flow_dissect: use programable dissector in skb_flow_dissect and friends")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andre Noll <maan@tuebingen.mpg.de>
Diagnosed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the link is filtered out, loop index should also be updated. If not,
loop index will not be correct.
Fixes: dc599f76c2 ("net: Add support for filtering link dump by master device and kind")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
size_t is way too much for an integer not exceeding 64.
Space savings: 10 bytes!
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-10 (-10)
function old new delta
napi_consume_skb 165 163 -2
__kfree_skb_flush 56 53 -3
__kfree_skb_defer 97 92 -5
Total: Before=154865639, After=154865629, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing NDA_VLAN attribute's size.
Fixes: 1e53d5bb88 ("net: Pass VLAN ID to rtnl_fdb_notify.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding validation support for the ETHTOOL_PHY_DOWNSHIFT. Functional
implementation needs to be done in the individual PHY drivers.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding get_tunable/set_tunable function pointer to the phy_driver
structure, and uses these function pointers to implement the
ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE ioctls.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make struct pernet_operations::id unsigned.
There are 2 reasons to do so:
1)
This field is really an index into an zero based array and
thus is unsigned entity. Using negative value is out-of-bound
access by definition.
2)
On x86_64 unsigned 32-bit data which are mixed with pointers
via array indexing or offsets added or subtracted to pointers
are preffered to signed 32-bit data.
"int" being used as an array index needs to be sign-extended
to 64-bit before being used.
void f(long *p, int i)
{
g(p[i]);
}
roughly translates to
movsx rsi, esi
mov rdi, [rsi+...]
call g
MOVSX is 3 byte instruction which isn't necessary if the variable is
unsigned because x86_64 is zero extending by default.
Now, there is net_generic() function which, you guessed it right, uses
"int" as an array index:
static inline void *net_generic(const struct net *net, int id)
{
...
ptr = ng->ptr[id - 1];
...
}
And this function is used a lot, so those sign extensions add up.
Patch snipes ~1730 bytes on allyesconfig kernel (without all junk
messing with code generation):
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
Unfortunately some functions actually grow bigger.
This is a semmingly random artefact of code generation with register
allocator being used differently. gcc decides that some variable
needs to live in new r8+ registers and every access now requires REX
prefix. Or it is shifted into r12, so [r12+0] addressing mode has to be
used which is longer than [r8]
However, overall balance is in negative direction:
add/remove: 0/0 grow/shrink: 70/598 up/down: 396/-2126 (-1730)
function old new delta
nfsd4_lock 3886 3959 +73
tipc_link_build_proto_msg 1096 1140 +44
mac80211_hwsim_new_radio 2776 2808 +32
tipc_mon_rcv 1032 1058 +26
svcauth_gss_legacy_init 1413 1429 +16
tipc_bcbase_select_primary 379 392 +13
nfsd4_exchange_id 1247 1260 +13
nfsd4_setclientid_confirm 782 793 +11
...
put_client_renew_locked 494 480 -14
ip_set_sockfn_get 730 716 -14
geneve_sock_add 829 813 -16
nfsd4_sequence_done 721 703 -18
nlmclnt_lookup_host 708 686 -22
nfsd4_lockt 1085 1063 -22
nfs_get_client 1077 1050 -27
tcf_bpf_init 1106 1076 -30
nfsd4_encode_fattr 5997 5930 -67
Total: Before=154856051, After=154854321, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei reports we still allocate netns ID from idr after we destroy
it in cleanup_net().
cleanup_net():
...
idr_destroy(&net->netns_ids);
...
list_for_each_entry_reverse(ops, &pernet_list, list)
ops_exit_list(ops, &net_exit_list);
-> rollback_registered_many()
-> rtmsg_ifinfo_build_skb()
-> rtnl_fill_ifinfo()
-> peernet2id_alloc()
After that point we should not even access net->netns_ids, we
should check the death of the current netns as early as we can in
peernet2id_alloc().
For net-next we can consider to avoid sending rtmsg totally,
it is a good optimization for netns teardown path.
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Reported-by: Andrei Vagin <avagin@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of netpoll_poll_lock() own NAPI_STATE_SCHED
Callers of netpoll_poll_unlock() have BH blocked between
the NAPI_STATE_SCHED being cleared and poll_lock is released.
We can avoid the spinlock which has no contention, and use cmpxchg()
on poll_owner which we need to set anyway.
This removes a possible lockdep violation after the cited commit,
since sk_busy_loop() re-enables BH before calling busy_poll_stop()
Fixes: 217f697436 ("net: busy-poll: allow preemption in sk_busy_loop()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers use napi_complete_done() or napi_complete() when
they drained RX ring and right before re-enabling device interrupts.
In busy polling, we can avoid interrupts being delivered since
we are polling RX ring in a controlled loop.
Drivers can chose to use napi_complete_done() return value
to reduce interrupts overhead while busy polling is active.
This is optional, legacy drivers should work fine even
if not updated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job"),
sk_busy_loop() needs a bit of care :
softirqs might be delayed since we do not allow preemption yet.
This patch adds preemptiom points in sk_busy_loop(),
and makes sure no unnecessary cache line dirtying
or atomic operations are done while looping.
A new flag is added into napi->state : NAPI_STATE_IN_BUSY_POLL
This prevents napi_complete_done() from clearing NAPIF_STATE_SCHED,
so that sk_busy_loop() does not have to grab it again.
Similarly, netpoll_poll_lock() is done one time.
This gives about 10 to 20 % improvement in various busy polling
tests, especially when many threads are busy polling in
configurations with large number of NIC queues.
This should allow experimenting with bigger delays without
hurting overall latencies.
Tested:
On a 40Gb mlx4 NIC, 32 RX/TX queues.
echo 70 >/proc/sys/net/core/busy_read
for i in `seq 1 40`; do echo -n $i: ; ./super_netperf $i -H lpaa24 -t UDP_RR -- -N -n; done
Before: After:
1: 90072 92819
2: 157289 184007
3: 235772 213504
4: 344074 357513
5: 394755 458267
6: 461151 487819
7: 549116 625963
8: 544423 716219
9: 720460 738446
10: 794686 837612
11: 915998 923960
12: 937507 925107
13: 1019677 971506
14: 1046831 1113650
15: 1114154 1148902
16: 1105221 1179263
17: 1266552 1299585
18: 1258454 1383817
19: 1341453 1312194
20: 1363557 1488487
21: 1387979 1501004
22: 1417552 1601683
23: 1550049 1642002
24: 1568876 1601915
25: 1560239 1683607
26: 1640207 1745211
27: 1706540 1723574
28: 1638518 1722036
29: 1734309 1757447
30: 1782007 1855436
31: 1724806 1888539
32: 1717716 1944297
33: 1778716 1869118
34: 1805738 1983466
35: 1815694 2020758
36: 1893059 2035632
37: 1843406 2034653
38: 1888830 2086580
39: 1972827 2143567
40: 1877729 2181851
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_xdp_size() only considers the size of the actual payload attribute,
and misses the space taken by the attribute used for nesting (IFLA_XDP).
Fixes: d1fdd91386 ("rtnl: add option for setting link xdp prog")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size reported by rtnl_vfinfo_size doesn't match the space used by
rtnl_fill_vfinfo.
rtnl_vfinfo_size currently doesn't account for the nest attributes
used by statistics (added in commit 3b766cd832), nor for struct
ifla_vf_tx_rate (since commit ed616689a3, which added ifla_vf_rate
to the dump without removing ifla_vf_tx_rate, but replaced
ifla_vf_tx_rate with ifla_vf_rate in the size computation).
Fixes: 3b766cd832 ("net/core: Add reading VF statistics through the PF netdevice")
Fixes: ed616689a3 ("net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 14135f30e3 ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Tom patch, thoff field could point past the end of the buffer,
this could fool some callers.
If an skb was provided, skb->len should be the upper limit.
If not, hlen is supposed to be the upper limit.
Fixes: a6e544b0a8 ("flow_dissector: Jump to exit code in __skb_flow_dissect")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yibin Yang <yibyang@cisco.com
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bpf program calls bpf_redirect(dev, 0) and dev is
an ipip/ip6tnl, it currently includes the mac header.
e.g. If dev is ipip, the end result is IP-EthHdr-IP instead
of IP-IP.
The fix is to pull the mac header. At ingress, skb_postpull_rcsum()
is not needed because the ethhdr should have been pulled once already
and then got pushed back just before calling the bpf_prog.
At egress, this patch calls skb_postpull_rcsum().
If bpf_redirect(dev, BPF_F_INGRESS) is called,
it also fails now because it calls dev_forward_skb() which
eventually calls eth_type_trans(skb, dev). The eth_type_trans()
will set skb->type = PACKET_OTHERHOST because the mac address
does not match the redirecting dev->dev_addr. The PACKET_OTHERHOST
will eventually cause the ip_rcv() errors out. To fix this,
____dev_forward_skb() is added.
Joint work with Daniel Borkmann.
Fixes: cfc7381b30 ("ip_tunnel: add collect_md mode to IPIP tunnel")
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more users except from net/core/dev.c
napi_hash_add() can now be static.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new type of interfaceless lightweight tunnel (SEG6),
enabling the encapsulation and injection of SRH within locally emitted
packets and forwarded packets.
>From a configuration viewpoint, a seg6 tunnel would be configured as follows:
ip -6 ro ad fc00::1/128 encap seg6 mode encap segs fc42::1,fc42::2,fc42::3 dev eth0
Any packet whose destination address is fc00::1 would thus be encapsulated
within an outer IPv6 header containing the SRH with three segments, and would
actually be routed to the first segment of the list. If `mode inline' was
specified instead of `mode encap', then the SRH would be directly inserted
after the IPv6 header without outer encapsulation.
The inline mode is only available if CONFIG_IPV6_SEG6_INLINE is enabled. This
feature was made configurable because direct header insertion may break
several mechanisms such as PMTUD or IPSec AH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid having dangling function pointers left behind, reset calcit in
rtnl_unregister(), too.
This is no issue so far, as only the rtnl core registers a netlink
handler with a calcit hook which won't be unregistered, but may become
one if new code makes use of the calcit hook.
Fixes: c7ac8679be ("rtnetlink: Compute and store minimum ifinfo...")
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receiving a GSO packet in dev_gro_receive() is not uncommon
in stacked devices, or devices partially implementing LRO/GRO
like bnx2x. GRO is implementing the aggregation the device
was not able to do itself.
Current code causes reorders, like in following case :
For a given flow where sender sent 3 packets P1,P2,P3,P4
Receiver might receive P1 as a single packet, stored in GRO engine.
Then P2-P4 are received as a single GSO packet, immediately given to
upper stack, while P1 is held in GRO engine.
This patch will make sure P1 is given to upper stack, then P2-P4
immediately after.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Install the callbacks via the state machine. Use multi state support to avoid
custom list handling for the multiple instances.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20161103145021.28528-10-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Without this check, it is not possible to create two rules that
are identical except for their UID ranges. For example:
root@net-test:/# ip rule add prio 1000 lookup 300
root@net-test:/# ip rule add prio 1000 uidrange 100-200 lookup 300
RTNETLINK answers: File exists
root@net-test:/# ip rule add prio 1000 uidrange 100-199 lookup 100
root@net-test:/# ip rule add prio 1000 uidrange 200-299 lookup 200
root@net-test:/# ip rule add prio 1000 uidrange 300-399 lookup 100
RTNETLINK answers: File exists
Tested: https://android-review.googlesource.com/#/c/299980/
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set sk_err when dequeuing errors from the error queue.
Doing so results in:
a) Bugs: By overwriting existing sk_err values, it possibly
hides legitimate errors. It is also incorrect when local
errors are queued with ip_local_error. That happens in the
context of a system call, which already returns the error
code.
b) Inconsistent behavior: When there are pending errors on
the error queue, sk_err is sometimes 0 (e.g., for
the first timestamp on the error queue) and sometimes
set to an error code (after dequeuing the first
timestamp).
c) Suboptimality: Setting sk_err to ENOMSG on simple
TX timestamps can abort parallel reads and writes.
Removing this line doesn't break userspace. This is because
userspace code cannot rely on sk_err for detecting whether
there is something on the error queue. Except for ICMP messages
received for UDP and RAW, sk_err is not set at enqueue time,
and as a result sk_err can be 0 while there are plenty of
errors on the error queue.
For ICMP packets in UDP and RAW, sk_err is set when they are
enqueued on the error queue, but that does not result in aborting
reads and writes. For such cases, sk_err is only readable via
getsockopt(SO_ERROR) which will reset the value of sk_err on
its own. More importantly, prior to this patch,
recvmsg(MSG_ERRQUEUE) has a race on setting sk_err (i.e.,
sk_err is set by sock_dequeue_err_skb without atomic ops or
locks) which can store 0 in sk_err even when we have ICMP
messages pending. Removing this line from sock_dequeue_err_skb
eliminates that race.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag IFF_NO_QUEUE marks virtual device drivers that doesn't need a
default qdisc attached, given they will be backed by physical device,
that already have a qdisc attached for pushback.
It is still supported to attach a qdisc to a IFF_NO_QUEUE device, as
this can be useful for difference policy reasons (e.g. bandwidth
limiting containers). For this to work, the tx_queue_len need to have
a sane value, because some qdiscs inherit/copy the tx_queue_len
(namely, pfifo, bfifo, gred, htb, plug and sfb).
Commit a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling
ether_setup()") caught situations where some drivers didn't initialize
tx_queue_len. The problem with the commit was choosing 1 as the
fallback value.
A qdisc queue length of 1 causes more harm than good, because it
creates hard to debug situations for userspace. It gives userspace a
false sense of a working config after attaching a qdisc. As low
volume traffic (that doesn't activate the qdisc policy) works,
like ping, while traffic that e.g. needs shaping cannot reach the
configured policy levels, given the queue length is too small.
This patch change the value to DEFAULT_TX_QUEUE_LEN, given other
IFF_NO_QUEUE devices (that call ether_setup()) also use this value.
Fixes: a813104d92 ("IFF_NO_QUEUE: Fix for drivers not calling ether_setup()")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol sockets (struct sock) don't have UIDs, but most of the
time, they map 1:1 to userspace sockets (struct socket) which do.
Various operations such as the iptables xt_owner match need
access to the "UID of a socket", and do so by following the
backpointer to the struct socket. This involves taking
sk_callback_lock and doesn't work when there is no socket
because userspace has already called close().
Simplify this by adding a sk_uid field to struct sock whose value
matches the UID of the corresponding struct socket. The semantics
are as follows:
1. Whenever sk_socket is non-null: sk_uid is the same as the UID
in sk_socket, i.e., matches the return value of sock_i_uid.
Specifically, the UID is set when userspace calls socket(),
fchown(), or accept().
2. When sk_socket is NULL, sk_uid is defined as follows:
- For a socket that no longer has a sk_socket because
userspace has called close(): the previous UID.
- For a cloned socket (e.g., an incoming connection that is
established but on which userspace has not yet called
accept): the UID of the socket it was cloned from.
- For a socket that has never had an sk_socket: UID 0 inside
the user namespace corresponding to the network namespace
the socket belongs to.
Kernel sockets created by sock_create_kern are a special case
of #1 and sk_uid is the user that created them. For kernel
sockets created at network namespace creation time, such as the
per-processor ICMP and TCP sockets, this is the user that created
the network namespace.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At accept() time, it is possible the parent has a non zero
sk_err_soft, leftover from a prior error.
Make sure we do not leave this value in the child, as it
makes future getsockopt(SO_ERROR) calls quite unreliable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting and using XPS when QoS via traffic
classes is enabled. With this change we will factor in the priority and
traffic class mapping of the packet and use that information to correctly
select the queue.
This allows us to define a set of queues for a given traffic class via
mqprio and then configure the XPS mapping for those queues so that the
traffic flows can avoid head-of-line blocking between the individual CPUs
if so desired.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the code for removing queues from the XPS map and makes
it so that we can apply the code any time we change either the number of
traffic classes or the mapping of a given block of queues. This way we
avoid having queues pulling traffic from a foreign traffic class.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysfs attribute for a Tx queue that allows us to determine the
traffic class for a given queue. This will allow us to more easily
determine this in the future. It is needed as XPS will take the traffic
class for a group of queues into account in order to avoid pulling traffic
from one traffic class into another.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions for configuring the traffic class to queue mappings have
other effects that need to be addressed. Instead of trying to export a
bunch of new functions just relocate the functions so that we can
instrument them directly with the functionality they will need.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
netdev_walk_all_lower_dev is not properly walking the lower device
list. Commit 1a3f060c1a made netdev_walk_all_lower_dev similar
to netdev_walk_all_upper_dev_rcu and netdev_walk_all_lower_dev_rcu
but failed to update its netdev_next_lower_dev iterator. This patch
fixes that.
Fixes: 1a3f060c1a ("net: Introduce new api for walking upper and
lower devices")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
ethtool -K eth0 tso off tx on
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N
ethtool -K eth0 tx off
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N
v2:
- add EXPORT_SYMBOL_GPL(validate_xmit_skb_list)
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
No one can see these events, because a network namespace can not be
destroyed, if it has sockets.
Unlike other devices, uevent-s for network devices are generated
only inside their network namespaces. They are filtered in
kobj_bcast_filter()
My experiments shows that net namespaces are destroyed more 30% faster
with this optimization.
Here is a perf output for destroying network namespaces without this
patch.
- 94.76% 0.02% kworker/u48:1 [kernel.kallsyms] [k] cleanup_net
- 94.74% cleanup_net
- 94.64% ops_exit_list.isra.4
- 41.61% default_device_exit_batch
- 41.47% unregister_netdevice_many
- rollback_registered_many
- 40.36% netdev_unregister_kobject
- 14.55% device_del
+ 13.71% kobject_uevent
- 13.04% netdev_queue_update_kobjects
+ 12.96% kobject_put
- 12.72% net_rx_queue_update_kobjects
kobject_put
- kobject_release
+ 12.69% kobject_uevent
+ 0.80% call_netdevice_notifiers_info
+ 19.57% nfsd_exit_net
+ 11.15% tcp_net_metrics_exit
+ 8.25% rpcsec_gss_exit_net
It's very critical to optimize the exit path for network namespaces,
because they are destroyed under net_mutex and many namespaces can be
destroyed for one iteration.
v2: use dev_set_uevent_suppress()
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about an uninitialized pointer dereference in the vlan
priority handling:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
net/core/flow_dissector.c:281:61: error: 'vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As pointed out by Jiri Pirko, the variable is never actually used
without being initialized first as the only way it end up uninitialized
is with skb_vlan_tag_present(skb)==true, and that means it does not
get accessed.
However, the warning hints at some related issues that I'm addressing
here:
- the second check for the vlan tag is different from the first one
that tests the skb for being NULL first, causing both the warning
and a possible NULL pointer dereference that was not entirely fixed.
- The same patch that introduced the NULL pointer check dropped an
earlier optimization that skipped the repeated check of the
protocol type
- The local '_vlan' variable is referenced through the 'vlan' pointer
but the variable has gone out of scope by the time that it is
accessed, causing undefined behavior
Caching the result of the 'skb && skb_vlan_tag_present(skb)' check
in a local variable allows the compiler to further optimize the
later check. With those changes, the warning also disappears.
Fixes: 3805a938a6 ("flow_dissector: Check skb for VLAN only if skb specified.")
Fixes: d5709f7ab7 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port_type_set() is been called and the new port type set is the same
as the old one, just return success.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_mutex can be locked for a long time. It may be because many
namespaces are being destroyed or many processes decide to create
a network namespace.
Both these operations are heavy, so it is better to have an ability to
kill a process which is waiting net_mutex.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use case is mainly for soreuseport to select sockets for the local
numa node, but since generic, lets also add this for other networking
and tracing program types.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic sock operations that udp code can use with its own
memory accounting schema. No functional change is introduced
in the existing APIs.
v4 -> v5:
- avoid whitespace changes
v2 -> v4:
- avoid exporting __sock_enqueue_skb
v1 -> v2:
- avoid export sock_rmem_free
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bc51dddf98 ("netns: avoid disabling irq for
netns id") as it was found to cause problems with systems running
SELinux/audit, see the mailing list thread below:
* http://marc.info/?t=147694653900002&r=1&w=2
Eventually we should be able to reintroduce this code once we have
rewritten the audit multicast code to queue messages much the same
way we do for unicast messages. A tracking issue for this can be
found below:
* https://github.com/linux-audit/audit-kernel/issues/23
Reported-by: Stephen Smalley <sds@tycho.nsa.gov>
Reported-by: Elad Raz <e@eladraz.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039
Fixes: 9b174d88c2 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f19 ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a panic when calling eth_get_headlen(). Noticed on i40e driver.
Fixes: d5709f7ab7 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: Eric Garver <e@erig.me>
Reviewed-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
reuseport_add_sock() is not used from a module,
no need to export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjacency code only has debugs for the insert case. Add debugs for
the remove path and make both consistently worded to make it easier
to follow the insert and removal with reference counts.
In addition, change the BUG to a WARN_ON. A missing adjacency at
removal time is not cause for a panic.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only direct adjacencies are maintained. All upper or lower devices can
be learned via the new walk API which recursively walks the adj_list for
upper devices or lower devices.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces netdev_walk_all_upper_dev_rcu,
netdev_walk_all_lower_dev and netdev_walk_all_lower_dev_rcu. These
functions recursively walk the adj_list of devices to determine all upper
and lower devices.
The functions take a callback function that is invoked for each device
in the list. If the callback returns non-0, the walk is terminated and
the functions return that code back to callers.
v3
- simplified netdev_has_upper_dev_all_rcu and __netdev_has_upper_dev and
removed typecast as suggested by Stephen
v2
- fixed definition of netdev_next_lower_dev_rcu to mirror the upper_dev
version.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 93409033ae ("net: Add netdev all_adj_list refcnt propagation to
fix panic") propagated the refnr to insert and remove functions tracking
the netdev adjacency graph. However, for the insert path the refnr can
only be 1. Accordingly, remove the refnr argument to make that clear.
ie., the refnr arg in 93409033ae was only needed for the remove path.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check is for max_mtu but message reports min_mtu.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Jesper commit back in linux-3.18, we trigger a lockdep
splat in proc_create_data() while allocating memory from
pktgen_change_name().
This patch converts t->if_lock to a mutex, since it is now only
used from control path, and adds proper locking to pktgen_change_name()
1) pktgen_thread_lock to protect the outer loop (iterating threads)
2) t->if_lock to protect the inner loop (iterating devices)
Note that before Jesper patch, pktgen_change_name() was lacking proper
protection, but lockdep was not able to detect the problem.
Fixes: 8788370a1d ("pktgen: RCU-ify "if_list" to remove lock in next_to_run()")
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users of lwt tunnels may set up some secondary state in build_state
function. Add a corresponding destroy_state function to allow users to
clean up state. This destroy state function is called from lwstate_free.
Also, we now free lwstate using kfree_rcu so user can assume structure
is not freed before rcu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
extract as much possible uncertainty from a running system at boot time as
possible, hoping to capitalize on any possible variation in CPU operation
(due to runtime data differences, hardware differences, SMP ordering,
thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example for
how to manipulate kernel code using the gcc plugin internals.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>
iQIcBAABCgAGBQJX/BAFAAoJEIly9N/cbcAmzW8QALFbCs7EFFkML+M/M/9d8zEk
1QbUs/z8covJTTT1PjSdw7JUrAMulI3S00owpcQVd/PcWjRPU80QwfsXBgIB0tvC
Kub2qxn6Oaf+kTB646zwjFgjdCecw/USJP+90nfcu2+LCnE8ReclKd1aUee+Bnhm
iDEUyH2ONIoWq6ta2Z9sA7+E4y2ZgOlmW0iga3Mnf+OcPtLE70fWPoe5E4g9DpYk
B+kiPDrD9ql5zsHaEnKG1ldjiAZ1L6Grk8rGgLEXmbOWtTOFmnUhR+raK5NA/RCw
MXNuyPay5aYPpqDHFm+OuaWQAiPWfPNWM3Ett4k0d9ZWLixTcD1z68AciExwk7aW
SEA8b1Jwbg05ZNYM7NJB6t6suKC4dGPxWzKFOhmBicsh2Ni5f+Az0BQL6q8/V8/4
8UEqDLuFlPJBB50A3z5ngCVeYJKZe8Bg/Swb4zXl6mIzZ9darLzXDEV6ystfPXxJ
e1AdBb41WC+O2SAI4l64yyeswkGo3Iw2oMbXG5jmFl6wY/xGp7dWxw7gfnhC6oOh
afOT54p2OUDfSAbJaO0IHliWoIdmE5ZYdVYVU9Ek+uWyaIwcXhNmqRg+Uqmo32jf
cP5J9x2kF3RdOcbSHXmFp++fU+wkhBtEcjkNpvkjpi4xyA47IWS7lrVBBebrCq9R
pa/A7CNQwibIV6YD8+/p
=1dUK
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
This reverts commit 6ae23ad362.
The code has been in kernel since 4.4 but there are no in tree
code that uses. Unused code is broken code, remove it.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "vf_vlan_info" struct ends with a 2 byte struct hole so we have to
memset it to ensure that no stack information is revealed to user space.
Fixes: 79aab093a0 ('net: Update API for VF vlan protocol 802.1ad support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking into an MTU issue with sfc, I started noticing that almost
every NIC driver with an ndo_change_mtu function implemented almost
exactly the same range checks, and in many cases, that was the only
practical thing their ndo_change_mtu function was doing. Quite a few
drivers have either 68, 64, 60 or 46 as their minimum MTU value checked,
and then various sizes from 1500 to 65535 for their maximum MTU value. We
can remove a whole lot of redundant code here if we simple store min_mtu
and max_mtu in net_device, and check against those in net/core/dev.c's
dev_set_mtu().
In theory, there should be zero functional change with this patch, it just
puts the infrastructure in place. Subsequent patches will attempt to start
using said infrastructure, with theoretically zero change in
functionality.
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __latent_entropy gcc attribute can be used only on functions and
variables. If it is on a function then the plugin will instrument it for
gathering control-flow entropy. If the attribute is on a variable then
the plugin will initialize it with random contents. The variable must
be an integer, an integer array type or a structure with integer fields.
These specific functions have been selected because they are init
functions (to help gather boot-time entropy), are called at unpredictable
times, or they have variable loops, each of which provide some level of
latent entropy.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
[kees: expanded commit message]
Signed-off-by: Kees Cook <keescook@chromium.org>
Merge updates from Andrew Morton:
- fsnotify updates
- ocfs2 updates
- all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (127 commits)
console: don't prefer first registered if DT specifies stdout-path
cred: simpler, 1D supplementary groups
CREDITS: update Pavel's information, add GPG key, remove snail mail address
mailmap: add Johan Hovold
.gitattributes: set git diff driver for C source code files
uprobes: remove function declarations from arch/{mips,s390}
spelling.txt: "modeled" is spelt correctly
nmi_backtrace: generate one-line reports for idle cpus
arch/tile: adopt the new nmi_backtrace framework
nmi_backtrace: do a local dump_stack() instead of a self-NMI
nmi_backtrace: add more trigger_*_cpu_backtrace() methods
min/max: remove sparse warnings when they're nested
Documentation/filesystems/proc.txt: add more description for maps/smaps
mm, proc: fix region lost in /proc/self/smaps
proc: fix timerslack_ns CAP_SYS_NICE check when adjusting self
proc: add LSM hook checks to /proc/<tid>/timerslack_ns
proc: relax /proc/<tid>/timerslack_ns capability requirements
meminfo: break apart a very long seq_printf with #ifdefs
seq/proc: modify seq_put_decimal_[u]ll to take a const char *, not char
proc: faster /proc/*/status
...
The cgroup core and the memory controller need to track socket ownership
for different purposes, but the tracking sites being entirely different
is kind of ugly.
Be a better citizen and rename the memory controller callbacks to match
the cgroup core callbacks, then move them to the same place.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20160914194846.11153-3-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS splice updates from Al Viro:
"There's a bunch of branches this cycle, both mine and from other folks
and I'd rather send pull requests separately.
This one is the conversion of ->splice_read() to ITER_PIPE iov_iter
(and introduction of such). Gets rid of a lot of code in fs/splice.c
and elsewhere; there will be followups, but these are for the next
cycle... Some pipe/splice-related cleanups from Miklos in the same
branch as well"
* 'work.splice_read' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
pipe: fix comment in pipe_buf_operations
pipe: add pipe_buf_steal() helper
pipe: add pipe_buf_confirm() helper
pipe: add pipe_buf_release() helper
pipe: add pipe_buf_get() helper
relay: simplify relay_file_read()
switch default_file_splice_read() to use of pipe-backed iov_iter
switch generic_file_splice_read() to use of ->read_iter()
new iov_iter flavour: pipe-backed
fuse_dev_splice_read(): switch to add_to_pipe()
skb_splice_bits(): get rid of callback
new helper: add_to_pipe()
splice: lift pipe_lock out of splice_to_pipe()
splice: switch get_iovec_page_array() to iov_iter
splice_to_pipe(): don't open-code wakeup_pipe_readers()
consistent treatment of EFAULT on O_DIRECT read/write
Pull namespace updates from Eric Biederman:
"This set of changes is a number of smaller things that have been
overlooked in other development cycles focused on more fundamental
change. The devpts changes are small things that were a distraction
until we managed to kill off DEVPTS_MULTPLE_INSTANCES. There is an
trivial regression fix to autofs for the unprivileged mount changes
that went in last cycle. A pair of ioctls has been added by Andrey
Vagin making it is possible to discover the relationships between
namespaces when referring to them through file descriptors.
The big user visible change is starting to add simple resource limits
to catch programs that misbehave. With namespaces in general and user
namespaces in particular allowing users to use more kinds of
resources, it has become important to have something to limit errant
programs. Because the purpose of these limits is to catch errant
programs the code needs to be inexpensive to use as it always on, and
the default limits need to be high enough that well behaved programs
on well behaved systems don't encounter them.
To this end, after some review I have implemented per user per user
namespace limits, and use them to limit the number of namespaces. The
limits being per user mean that one user can not exhause the limits of
another user. The limits being per user namespace allow contexts where
the limit is 0 and security conscious folks can remove from their
threat anlysis the code used to manage namespaces (as they have
historically done as it root only). At the same time the limits being
per user namespace allow other parts of the system to use namespaces.
Namespaces are increasingly being used in application sand boxing
scenarios so an all or nothing disable for the entire system for the
security conscious folks makes increasing use of these sandboxes
impossible.
There is also added a limit on the maximum number of mounts present in
a single mount namespace. It is nontrivial to guess what a reasonable
system wide limit on the number of mount structure in the kernel would
be, especially as it various based on how a system is using
containers. A limit on the number of mounts in a mount namespace
however is much easier to understand and set. In most cases in
practice only about 1000 mounts are used. Given that some autofs
scenarious have the potential to be 30,000 to 50,000 mounts I have set
the default limit for the number of mounts at 100,000 which is well
above every known set of users but low enough that the mount hash
tables don't degrade unreaonsably.
These limits are a start. I expect this estabilishes a pattern that
other limits for resources that namespaces use will follow. There has
been interest in making inotify event limits per user per user
namespace as well as interest expressed in making details about what
is going on in the kernel more visible"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (28 commits)
autofs: Fix automounts by using current_real_cred()->uid
mnt: Add a per mount namespace limit on the number of mounts
netns: move {inc,dec}_net_namespaces into #ifdef
nsfs: Simplify __ns_get_path
tools/testing: add a test to check nsfs ioctl-s
nsfs: add ioctl to get a parent namespace
nsfs: add ioctl to get an owning user namespace for ns file descriptor
kernel: add a helper to get an owning user namespace for a namespace
devpts: Change the owner of /dev/pts/ptmx to the mounter of /dev/pts
devpts: Remove sync_filesystems
devpts: Make devpts_kill_sb safe if fsi is NULL
devpts: Simplify devpts_mount by using mount_nodev
devpts: Move the creation of /dev/pts/ptmx into fill_super
devpts: Move parse_mount_options into fill_super
userns: When the per user per user namespace limit is reached return ENOSPC
userns; Document per user per user namespace limits.
mntns: Add a limit on the number of mount namespaces.
netns: Add a limit on the number of net namespaces
cgroupns: Add a limit on the number of cgroup namespaces
ipcns: Add a limit on the number of ipc namespaces
...
This is a respin of a patch to fix a relatively easily reproducible kernel
panic related to the all_adj_list handling for netdevs in recent kernels.
The following sequence of commands will reproduce the issue:
ip link add link eth0 name eth0.100 type vlan id 100
ip link add link eth0 name eth0.200 type vlan id 200
ip link add name testbr type bridge
ip link set eth0.100 master testbr
ip link set eth0.200 master testbr
ip link add link testbr mac0 type macvlan
ip link delete dev testbr
This creates an upper/lower tree of (excuse the poor ASCII art):
/---eth0.100-eth0
mac0-testbr-
\---eth0.200-eth0
When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from
the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one
reference to eth0 is added, so this results in a panic.
This change adds reference count propagation so things are handled properly.
Matthias Schiffer reported a similar crash in batman-adv:
https://github.com/freifunk-gluon/gluon/issues/680https://www.open-mesh.org/issues/247
which this patch also seems to resolve.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_vlan_pop/push were too generic, trying to support the cases where
skb->data is at mac header, and cases where skb->data is arbitrarily
elsewhere.
Supporting an arbitrary skb->data was complex and bogus:
- It failed to unwind skb->data to its original location post actual
pop/push.
(Also, semantic is not well defined for unwinding: If data was into
the eth header, need to use same offset from start; But if data was
at network header or beyond, need to adjust the original offset
according to the push/pull)
- It mangled the rcsum post actual push/pop, without taking into account
that the eth bytes might already have been pulled out of the csum.
Most callers (ovs, bpf) already had their skb->data at mac_header upon
invoking skb_vlan_pop/push.
Last caller that failed to do so (act_vlan) has been recently fixed.
Therefore, to simplify things, no longer support arbitrary skb->data
inputs for skb_vlan_pop/push().
skb->data is expected to be exactly at mac_header; WARN otherwise.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since pipe_lock is the outermost now, we don't need to drop/regain
socket locks around the call of splice_to_pipe() from skb_splice_bits(),
which kills the need to have a socket-specific callback; we can just
call splice_to_pipe() and be done with that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With the newly added support for IFLA_VF_VLAN_LIST netlink messages,
we get a warning about potential uninitialized variable use in
the parsing of the user input when enabling the -Wmaybe-uninitialized
warning:
net/core/rtnetlink.c: In function 'do_setvfinfo':
net/core/rtnetlink.c:1756:9: error: 'ivvl$' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I have not been able to prove whether it is possible to arrive in
this code with an empty IFLA_VF_VLAN_LIST block, but if we do,
then ndo_set_vf_vlan gets called with uninitialized arguments.
This adds an explicit check for an empty list, making it obvious
to the reader and the compiler that this cannot happen.
Fixes: 79aab093a0 ("net: Update API for VF vlan protocol 802.1ad support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 879c7220e8 ("net: pktgen: Observe needed_headroom
of the device") increased the 'pkt_overhead' field value by
LL_RESERVED_SPACE.
As a side effect the generated packet size, computed as:
/* Eth + IPh + UDPh + mpls */
datalen = pkt_dev->cur_pkt_size - 14 - 20 - 8 -
pkt_dev->pkt_overhead;
is decreased by the same value.
The above changed slightly the behavior of existing pktgen users,
and made the procfs interface somewhat inconsistent.
Fix it by restoring the previous pkt_overhead value and using
LL_RESERVED_SPACE as extralen in skb allocation.
Also, change pktgen_alloc_skb() to only partially reserve
the headroom to allow the caller to prefetch from ll header
start.
v1 -> v2:
- fixed some typos in the comments
Fixes: 879c7220e8 ("net: pktgen: Observe needed_headroom of the device")
Suggested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 900f65d361 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()") we no longer need
to export sk_stream_write_space()
From: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/core.c
net/netfilter/nf_tables_netdev.c
Resolve two conflicts before pull request for David's net-next tree:
1) Between c73c248490 ("netfilter: nf_tables_netdev: remove redundant
ip_hdr assignment") from the net tree and commit ddc8b6027a
("netfilter: introduce nft_set_pktinfo_{ipv4, ipv6}_validate()").
2) Between e8bffe0cf9 ("net: Add _nf_(un)register_hooks symbols") and
Aaron Conole's patches to replace list_head with single linked list.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This commit ensures that the rcu read-side lock is held while the
ingress hook is called. This ensures that a call to nf_hook_slow (and
ultimately nf_ingress) will be read protected.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the newly enforced limit on the number of namespaces,
we get a build warning if CONFIG_NETNS is disabled:
net/core/net_namespace.c:273:13: error: 'dec_net_namespaces' defined but not used [-Werror=unused-function]
net/core/net_namespace.c:268:24: error: 'inc_net_namespaces' defined but not used [-Werror=unused-function]
This moves the two added functions inside the #ifdef that guards
their callers.
Fixes: 703286608a ("netns: Add a limit on the number of net namespaces")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Add a small helper that complements 36bbef52c7 ("bpf: direct packet
write and access for helpers for clsact progs") for invalidating the
current skb->hash after mangling on headers via direct packet write.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same motivation as in commit 80b48c4457 ("bpf: don't use raw processor
id in generic helper"), but this time for XDP typed programs. Thus, allow
for preemption checks when we have DEBUG_PREEMPT enabled, and otherwise
use the raw variant.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use skb_to_full_sk() helper introduced in commit bd5eb35f16
("xfrm: take care of request sockets") as otherwise we miss tcp synack
messages, since ownership is on request socket and therefore it would
miss the sk_fullsock() check. Use skb_to_full_sk() as also done similarly
in the bpf_get_cgroup_classid() helper via 2309236c13 ("cls_cgroup:
get sk_classid only from full sockets") fix to not let this fall through.
Fixes: 4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Andrey Vagin <avagin@openvz.org>
Each namespace has an owning user namespace and now there is not way
to discover these relationships.
Pid and user namepaces are hierarchical. There is no way to discover
parent-child relationships too.
Why we may want to know relationships between namespaces?
One use would be visualization, in order to understand the running
system. Another would be to answer the question: what capability does
process X have to perform operations on a resource governed by namespace
Y?
One more use-case (which usually called abnormal) is checkpoint/restart.
In CRIU we are going to dump and restore nested namespaces.
There [1] was a discussion about which interface to choose to determing
relationships between namespaces.
Eric suggested to add two ioctl-s [2]:
> Grumble, Grumble. I think this may actually a case for creating ioctls
> for these two cases. Now that random nsfs file descriptors are bind
> mountable the original reason for using proc files is not as pressing.
>
> One ioctl for the user namespace that owns a file descriptor.
> One ioctl for the parent namespace of a namespace file descriptor.
Here is an implementaions of these ioctl-s.
$ man man7/namespaces.7
...
Since Linux 4.X, the following ioctl(2) calls are supported for
namespace file descriptors. The correct syntax is:
fd = ioctl(ns_fd, ioctl_type);
where ioctl_type is one of the following:
NS_GET_USERNS
Returns a file descriptor that refers to an owning user names‐
pace.
NS_GET_PARENT
Returns a file descriptor that refers to a parent namespace.
This ioctl(2) can be used for pid and user namespaces. For
user namespaces, NS_GET_PARENT and NS_GET_USERNS have the same
meaning.
In addition to generic ioctl(2) errors, the following specific ones
can occur:
EINVAL NS_GET_PARENT was called for a nonhierarchical namespace.
EPERM The requested namespace is outside of the current namespace
scope.
[1] https://lkml.org/lkml/2016/7/6/158
[2] https://lkml.org/lkml/2016/7/9/101
Changes for v2:
* don't return ENOENT for init_user_ns and init_pid_ns. There is nothing
outside of the init namespace, so we can return EPERM in this case too.
> The fewer special cases the easier the code is to get
> correct, and the easier it is to read. // Eric
Changes for v3:
* rename ns->get_owner() to ns->owner(). get_* usually means that it
grabs a reference.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Cc: "W. Trevor King" <wking@tremily.us>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Return -EPERM if an owning user namespace is outside of a process
current user namespace.
v2: In a first version ns_get_owner returned ENOENT for init_user_ns.
This special cases was removed from this version. There is nothing
outside of init_user_ns, so we can return EPERM.
v3: rename ns->get_owner() to ns->owner(). get_* usually means that it
grabs a reference.
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The current error codes returned when a the per user per user
namespace limit are hit (EINVAL, EUSERS, and ENFILE) are wrong. I
asked for advice on linux-api and it we made clear that those were
the wrong error code, but a correct effor code was not suggested.
The best general error code I have found for hitting a resource limit
is ENOSPC. It is not perfect but as it is unambiguous it will serve
until someone comes up with a better error code.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Fix 'skb_vlan_pop' to use eth_type_vlan instead of directly comparing
skb->protocol to ETH_P_8021Q or ETH_P_8021AD.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 93515d53b1
"net: move vlan pop/push functions into common code"
skb_vlan_pop was moved from its private location in openvswitch to
skbuff common code.
In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured
that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was
considered a no-op).
This validation was moved as is into the new common 'skb_vlan_pop'.
Alas, in its original location (openvswitch), there was a guarantee that
'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN'
condition made sense.
However there's no such guarantee in the generic 'skb_vlan_pop'.
For short packets received in rx path going through 'skb_vlan_pop',
this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non
hw-accel case) or to fail moving next tag into hw-accel tag.
Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely:
It is superfluous since inner '__skb_vlan_pop' already verifies there
are VLAN_ETH_HLEN writable bytes at the mac_header.
Note this presents a slight change to skb_vlan_pop() users:
In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now
returns an error, as opposed to previous "no-op" behavior.
Existing callers (e.g. tc act vlan, ovs) usually drop the packet if
'skb_vlan_pop' fails.
Fixes: 93515d53b1 ("net: move vlan pop/push functions into common code")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reviewed-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This exports the functionality of extracting the tag from the payload,
without moving next vlan tag into hw accel tag.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 8a29111c7 ("net: gro: allow to build full sized skb")
gro may build buffers with a frag_list. This can hurt forwarding
because most NICs can't offload such packets, they need to be
segmented in software. This patch splits buffers with a frag_list
at the frag_list pointer into buffers that can be TSO offloaded.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is cloned, the associated sock_cgroup_data is duplicated
but not its reference on the cgroup. As a result, the cgroup reference
count will underflow when both sockets are destroyed later on.
Fixes: bd1060a1d6 ("sock, cgroup: add sock->sk_cgroup")
Link: http://lkml.kernel.org/r/20160914194846.11153-2-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a nested attribute of offload stats to if_stats_msg
named IFLA_STATS_LINK_OFFLOAD_XSTATS.
Under it, add SW stats, meaning stats only per packets that went via
slowpath to the cpu, named IFLA_OFFLOAD_XSTATS_CPU_HIT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds BPF_CALL_<n>() macros and converts all the eBPF helper functions
to use them, in a similar fashion like we do with SYSCALL_DEFINE<n>() macros
that are used today. Motivation for this is to hide all the register handling
and all necessary casts from the user, so that it is done automatically in the
background when adding a BPF_CALL_<n>() call.
This makes current helpers easier to review, eases to write future helpers,
avoids getting the casting mess wrong, and allows for extending all helpers at
once (f.e. build time checks, etc). It also helps detecting more easily in
code reviews that unused registers are not instrumented in the code by accident,
breaking compatibility with existing programs.
BPF_CALL_<n>() internals are quite similar to SYSCALL_DEFINE<n>() ones with some
fundamental differences, for example, for generating the actual helper function
that carries all u64 regs, we need to fill unused regs, so that we always end up
with 5 u64 regs as an argument.
I reviewed several 0-5 generated BPF_CALL_<n>() variants of the .i results and
they look all as expected. No sparse issue spotted. We let this also sit for a
few days with Fengguang's kbuild test robot, and there were no issues seen. On
s390, it barked on the "uses dynamic stack allocation" notice, which is an old
one from bpf_perf_event_output{,_tp}() reappearing here due to the conversion
to the call wrapper, just telling that the perf raw record/frag sits on stack
(gcc with s390's -mwarn-dynamicstack), but that's all. Did various runtime tests
and they were fine as well. All eBPF helpers are now converted to use these
macros, getting rid of a good chunk of all the raw castings.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fetching ifindex, we don't need to test dev for being NULL since
we're always guaranteed to have a valid dev for clsact programs. Thus,
avoid this test in fast path.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BPF_SIZEOF() and BPF_FIELD_SIZEOF() macros to improve the code a bit
which otherwise often result in overly long bytes_to_bpf_size(sizeof())
and bytes_to_bpf_size(FIELD_SIZEOF()) lines. So place them into a macro
helper instead. Moreover, we currently have a BUILD_BUG_ON(BPF_FIELD_SIZEOF())
check in convert_bpf_extensions(), but we should rather make that generic
as well and add a BUILD_BUG_ON() test in all BPF_SIZEOF()/BPF_FIELD_SIZEOF()
users to detect any rewriter size issues at compile time. Note, there are
currently none, but we want to assert that it stays this way.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor misc cleanups, f.e. use sizeof(__u32) instead of hardcoding
and in __bpf_skb_max_len(), I missed that we always have skb->dev valid
anyway, so we can drop the unneeded test for dev; also few more other
misc bits addressed here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is defined but never used. Flagged with W=1
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, TCP BDP has increased by several orders of magnitude,
and some people are considering to reach the 2 Gbytes limit.
Even with current window scale limit of 14, ~1 Gbytes maps to ~740,000
MSS.
In presence of packet losses (or reorders), TCP stores incoming packets
into an out of order queue, and number of skbs sitting there waiting for
the missing packets to be received can be in the 10^5 range.
Most packets are appended to the tail of this queue, and when
packets can finally be transferred to receive queue, we scan the queue
from its head.
However, in presence of heavy losses, we might have to find an arbitrary
point in this queue, involving a linear scan for every incoming packet,
throwing away cpu caches.
This patch converts it to a RB tree, to get bounded latencies.
Yaogong wrote a preliminary patch about 2 years ago.
Eric did the rebase, added ofo_last_skb cache, polishing and tests.
Tested with network dropping between 1 and 10 % packets, with good
success (about 30 % increase of throughput in stress tests)
Next step would be to also use an RB tree for the write queue at sender
side ;)
Signed-off-by: Yaogong Wang <wygivan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-By: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following few steps will crash kernel -
(a) Create bonding master
> modprobe bonding miimon=50
(b) Create macvlan bridge on eth2
> ip link add link eth2 dev mvl0 address aa:0:0:0:0:01 \
type macvlan
(c) Now try adding eth2 into the bond
> echo +eth2 > /sys/class/net/bond0/bonding/slaves
<crash>
Bonding does lots of things before checking if the device enslaved is
busy or not.
In this case when the notifier call-chain sends notifications, the
bond_netdev_event() assumes that the rx_handler /rx_handler_data is
registered while the bond_enslave() hasn't progressed far enough to
register rx_handler for the new slave.
This patch adds a rx_handler check that can be performed right at the
beginning of the enslave code to avoid getting into this situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never read or change netns id in hardirq context,
the only place we read netns id in softirq context
is in vxlan_xmit(). So, it should be enough to just
disable BH.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netns id should be already allocated each time we change
netns, that is, in dev_change_net_namespace() (more precisely
in rtnl_fill_ifinfo()). It is safe to just call peernet2id() here.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original codes depend on that the function parameters are evaluated from
left to right. But the parameter's evaluation order is not defined in C
standard actually.
When flow_keys_have_l4(&keys) is invoked before ___skb_get_hash(skb, &keys,
hashrnd) with some compilers or environment, the keys passed to
flow_keys_have_l4 is not initialized.
Fixes: 6db61d79c1 ("flow_dissector: Ignore flow dissector return value from ___skb_get_hash")
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.
To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)
This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.
This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 145dd5f9c8 ("net: flush the softnet backlog in process
context"), we can easily batch calls to flush_all_backlogs() for all
devices processed in rollback_registered_many()
Tested:
Before patch, on an idle host.
modprobe dummy numdummies=10000
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
1,211,798 context-switches
1.302137465 seconds time elapsed
After patch:
perf stat -e context-switches -a rmmod dummy
Performance counter stats for 'system wide':
225,523 context-switches
0.721623566 seconds time elapsed
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in process_backlog(), the process_queue dequeuing is
performed with local IRQ disabled, to protect against
flush_backlog(), which runs in hard IRQ context.
This patch moves the flush operation to a work queue and runs the
callback with bottom half disabled to protect the process_queue
against dequeuing.
Since process_queue is now always manipulated in bottom half context,
the irq disable/enable pair around the dequeue operation are removed.
To keep the flush time as low as possible, the flush
works are scheduled on all online cpu simultaneously, using the
high priority work-queue and statically allocated, per cpu,
work structs.
Overall this change increases the time required to destroy a device
to improve slightly the packets reinjection performances.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer use this handler, we can delete it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use SLAB_DESTROY_BY_RCU for UDP,
we do not need sk_prot_clear_portaddr_nulls() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the features bit field has bits for internal only use as well, it
may happen that the kernel exports RTAX_FEATURES attribute with zero
value which is pointless.
Fix this by making sure the attribute is added only if the exported
value is non-zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
As recently discussed during the task_under_cgroup_hierarchy() addition,
we should get rid of the ifdefs surrounding the bpf_skb_under_cgroup()
helper. If related functionality is not built-in, the helper cannot be
used anyway, which is also in line with what we do for all other helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to 555c8a8623 ("bpf: avoid stack copy and use skb ctx for
event output") for also adding the event output helper for XDP typed
programs. The event output helper has been very useful in particular for
debugging or event notification purposes, since it's much faster and
flexible than regular trace printk due to programmatically being able to
attach meta data. Same flags structure applies as with tc BPF programs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a bpf_skb_change_tail() helper for tc BPF programs. The
basic idea is to expand or shrink the skb in a controlled manner. The
eBPF program can then rewrite the rest via helpers like bpf_skb_store_bytes(),
bpf_lX_csum_replace() and others rather than passing a raw buffer for
writing here.
bpf_skb_change_tail() is really a slow path helper and intended for
replies with f.e. ICMP control messages. Concept is similar to other
helpers like bpf_skb_change_proto() helper to keep the helper without
protocol specifics and let the BPF program mangle the remaining parts.
A flags field has been added and is reserved for now should we extend
the helper in future.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have a skb_pkt_type_ok() helper for checking the type before
mangling, make use of it instead of open coding. Follow-up to commit
8b10cab64c ("net: simplify and make pkt_type_ok() available for other
users") that came in after d2485c4242 ("bpf: add bpf_skb_change_type
helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vlan priority check to the flow dissector by adding new flow
dissector struct, flow_dissector_key_vlan which includes vlan tag
fields.
vlan_id and flow_label fields were under the same struct
(flow_dissector_key_tags). It was a convenient setting since struct
flow_dissector_key_tags is used by struct flow_keys and by setting
vlan_id and flow_label under the same struct, we get precisely 24 or 48
bytes in flow_keys from flow_dissector_key_basic.
Now, when adding vlan priority support, the code will be cleaner if
flow_label and vlan tag won't be under the same struct anymore.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early in the datapath skb_vlan_untag function is called, stripped
the vlan from the skb and set skb->vlan_tci and skb->vlan_proto fields.
The current dissection doesn't handle stripped vlan packets correctly.
In some flows, vlan doesn't exist in skb->data anymore when applying
flow dissection on the skb, fix that.
In case vlan info wasn't stripped before applying flow_dissector (RPS
flow for example), or in case of skb with multiple vlans (e.g. 802.1ad),
get the vlan info from skb->data. The flow_dissector correctly skips
any number of vlans and stores only the first level vlan.
Fixes: 0744dd00c1 ('net: introduce skb_flow_dissect()')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NET_NS is disabled, registering pernet operations causes
init() to be called immediately with init_net as an argument. Unfortunately
this leads to some pernet ops, such as proc_net_ns_init() to be called too
early, when init_net namespace has not been fully initialized. This causes
issues when we want to change pernet ops to use more data from the net
namespace in question, for example reference user namespace that owns our
network namespace.
To fix this we could either play game of musical chairs and rearrange init
order, or we could do the same as when CONFIG_NET_NS is enabled, and
postpone calling pernet ops->init() until namespace is set up properly.
Note that we can not simply undo commit ed160e839d ("[NET]: Cleanup
pernet operation without CONFIG_NET_NS") and use the same implementations
for __register_pernet_operations() and __unregister_pernet_operations(),
because many pernet ops are marked as __net_initdata and will be discarded,
which wreaks havoc on our ops lists. Here we rely on the fact that we only
use lists until init_net is fully initialized, which happens much earlier
than discarding __net_initdata sections.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea for type_check in dev_get_nest_level() was to count the number
of nested devices of the same type (currently, only macvlan or vlan
devices).
This prevented the false positive lockdep warning on configurations such
as:
eth0 <--- macvlan0 <--- vlan0 <--- macvlan1
However, this doesn't prevent a warning on a configuration such as:
eth0 <--- macvlan0 <--- vlan0
eth1 <--- vlan1 <--- macvlan1
In this case, all the locks end up with a nesting subclass of 1, so
lockdep thinks that there is still a deadlock:
- in the first case we have (macvlan_netdev_addr_lock_key, 1) and then
take (vlan_netdev_xmit_lock_key, 1)
- in the second case, we have (vlan_netdev_xmit_lock_key, 1) and then
take (macvlan_netdev_addr_lock_key, 1)
By removing the linktype check in dev_get_nest_level() and always
incrementing the nesting depth, lockdep considers this configuration
valid.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the bpf_try_make_writable() helper and all call sites we have in BPF,
it's currently defect with regards to skbs when the write_len spans into
non-linear parts, no matter if cloned or not.
There are multiple issues at once. First, using skb_store_bits() is not
correct since even if we have a cloned skb, page frags can still be shared.
To really make them private, we need to pull them in via __pskb_pull_tail()
first, which also gets us a private head via pskb_expand_head() implicitly.
This is for helpers like bpf_skb_store_bytes(), bpf_l3_csum_replace(),
bpf_l4_csum_replace(). Really, the only thing reasonable and working here
is to call skb_ensure_writable() before any write operation. Meaning, via
pskb_may_pull() it makes sure that parts we want to access are pulled in and
if not does so plus unclones the skb implicitly. If our write_len still fits
the headlen and we're cloned and our header of the clone is not writable,
then we need to make a private copy via pskb_expand_head(). skb_store_bits()
is a bit misleading and only safe to store into non-linear data in different
contexts such as 357b40a18b ("[IPV6]: IPV6_CHECKSUM socket option can
corrupt kernel memory").
For above BPF helper functions, it means after fixed bpf_try_make_writable(),
we've pulled in enough, so that we operate always based on skb->data. Thus,
the call to skb_header_pointer() and skb_store_bits() becomes superfluous.
In bpf_skb_store_bytes(), the len check is unnecessary too since it can
only pass in maximum of BPF stack size, so adding offset is guaranteed to
never overflow. Also bpf_l3/4_csum_replace() helpers must test for proper
offset alignment since they use __sum16 pointer for writing resulting csum.
The remaining helpers that change skb data not discussed here yet are
bpf_skb_vlan_push(), bpf_skb_vlan_pop() and bpf_skb_change_proto(). The
vlan helpers internally call either skb_ensure_writable() (pop case) and
skb_cow_head() (push case, for head expansion), respectively. Similarly,
bpf_skb_proto_xlat() takes care to not mangle page frags.
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Fixes: 91bc4822c3 ("tc: bpf: add checksum helpers")
Fixes: 3697649ff2 ("bpf: try harder on clones when writing into skb")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Fixes: 4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Reference: http://patchwork.ozlabs.org/patch/658500/
Suggested-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
The PPTP is encapsulated by GRE header with that GRE_VERSION bits
must contain one. But current GRE RPS needs the GRE_VERSION must be
zero. So RPS does not work for PPTP traffic.
In my test environment, there are four MIPS cores, and all traffic
are passed through by PPTP. As a result, only one core is 100% busy
while other three cores are very idle. After this patch, the usage
of four cores are balanced well.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the per-device linked list into a hashtable. The primary
motivation for this change is that currently, we're not tracking all the
qdiscs in hierarchy (e.g. excluding default qdiscs), as the lookup
performed over the linked list by qdisc_match_from_root() is rather
expensive.
The ultimate goal is to get rid of hidden qdiscs completely, which will
bring much more determinism in user experience.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Admin should be able to set any state. Currently, this fails
when lladdr is not changed and state is changed from
NUD_CONNECTED to NUD_STALE:
ip neigh add 192.168.8.1 lladdr 00:11:22:33:44:55 nud perm dev wlan0
ip neigh show to 192.168.8.1
192.168.8.1 dev wlan0 lladdr 00:11:22:33:44:55 PERMANENT
ip neigh change 192.168.8.1 lladdr 00:11:22:33:44:55 nud stale dev wlan0
ip neigh show to 192.168.8.1
192.168.8.1 dev wlan0 lladdr 00:11:22:33:44:55 PERMANENT
Problem may be from 2.1.X days.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Chunhui He <hchunhui@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60 ("bpf: introduce bpf_skb_vlan_push/pop() helpers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to commit f8ffad69c9 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the vfs dentry hashing to mix in the parent pointer at the
_beginning_ of the hash, rather than at the end.
That actually improves both the hash and the code generation, because we
can move more of the computation to the "static" part of the dcache
setup, and do less at lookup runtime.
It turns out that a lot of other hash users also really wanted to mix in
a base pointer as a 'salt' for the hash, and so the slightly extended
interface ends up working well for other cases too.
Users that want a string hash that is purely about the string pass in a
'salt' pointer of NULL.
* merge branch 'salted-string-hash':
fs/dcache.c: Save one 32-bit multiply in dcache lookup
vfs: make the string hashes salt the hash
NUD_STALE is used when the caller(e.g. arp_process()) can't guarantee
neighbour reachability. If the entry was NUD_VALID and lladdr is unchanged,
the entry state should not be changed.
Currently the code puts an extra "NUD_CONNECTED" condition. So if old state
was NUD_DELAY or NUD_PROBE (they are NUD_VALID but not NUD_CONNECTED), the
state can be changed to NUD_STALE.
This may cause problem. Because NUD_STALE lladdr doesn't guarantee
reachability, when we send traffic, the state will be changed to
NUD_DELAY. In normal case, if we get no confirmation (by dst_confirm()),
we will change the state to NUD_PROBE and send probe traffic. But now the
state may be reset to NUD_STALE again(e.g. by broadcast ARP packets),
so the probe traffic will not be sent. This situation may happen again and
again, and packets will be sent to an non-reachable lladdr forever.
The fix is to remove the "NUD_CONNECTED" condition. After that the
"NEIGH_UPDATE_F_WEAK_OVERRIDE" condition (used by IPv6) in that branch will
be redundant, so remove it.
This change may increase probe traffic, but it's essential since NUD_STALE
lladdr is unreliable. To ensure correctness, we prefer to resolve lladdr,
when we can't get confirmation, even while remote packets try to set
NUD_STALE state.
Signed-off-by: Chunhui He <hchunhui@mail.ustc.edu.cn>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the __output_custom() routine we currently use with
bpf_skb_copy(). I missed that when len is larger than the size of the
current handle, we can issue multiple invocations of copy_func, and
__output_custom() advances destination but also source buffer by the
written amount of bytes. When we have __output_custom(), this is actually
wrong since in that case the source buffer points to a non-linear object,
in our case an skb, which the copy_func helper is supposed to walk.
Therefore, since this is non-linear we thus need to pass the offset into
the helper, so that copy_func can use it for extracting the data from
the source object.
Therefore, adjust the callback signatures properly and pass offset
into the skb_header_pointer() invoked from bpf_skb_copy() callback. The
__DEFINE_OUTPUT_COPY_BODY() is adjusted to accommodate for two things:
i) to pass in whether we should advance source buffer or not; this is
a compile-time constant condition, ii) to pass in the offset for
__output_custom(), which we do with help of __VA_ARGS__, so everything
can stay inlined as is currently. Both changes allow for adapting the
__output_* fast-path helpers w/o extra overhead.
Fixes: 555c8a8623 ("bpf: avoid stack copy and use skb ctx for event output")
Fixes: 7e3f977edd ("perf, events: add non-linear data support for raw records")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IFLA_XDP_ATTACHED nested attribute is meant for read-only, and while
do_setlink properly ignores it, it should be more paranoid and reject
commands that try to set it.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sets the bpf program represented by fd as an early filter in the rx path
of the netdev. The fd must have been created as BPF_PROG_TYPE_XDP.
Providing a negative value as fd clears the program. Getting the fd back
via rtnl is not possible, therefore reading of this value merely
provides a bool whether the program is valid on the link or not.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one new netdev op for drivers implementing the BPF_PROG_TYPE_XDP
filter. The single op is used for both setup/query of the xdp program,
modelled after ndo_setup_tc.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bpf prog type that is intended to run in early stages of the
packet rx path. Only minimal packet metadata will be available, hence a
new context type, struct xdp_md, is exposed to userspace. So far only
expose the packet start and end pointers, and only in read mode.
An XDP program must return one of the well known enum values, all other
return codes are reserved for future use. Unfortunately, this
restriction is hard to enforce at verification time, so take the
approach of warning at runtime when such programs are encountered. Out
of bounds return codes should alias to XDP_ABORTED.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dccp verifies packet integrity, including length, at initial rcv in
dccp_invalid_packet, later pulls headers in dccp_enqueue_skb.
A call to sk_filter in-between can cause __skb_pull to wrap skb->len.
skb_copy_datagram_msg interprets this as a negative value, so
(correctly) fails with EFAULT. The negative length is reported in
ioctl SIOCINQ or possibly in a DCCP_WARN in dccp_close.
Introduce an sk_receive_skb variant that caps how small a filter
program can trim packets, and call this in dccp with the header
length. Excessively trimmed packets are now processed normally and
queued for reception as 0B payloads.
Fixes: 7c657876b6 ("[DCCP]: Initial implementation")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sockets can have a filter program attached that drops or trims
incoming packets based on the filter program return value.
Rose requires data packets to have at least ROSE_MIN_LEN bytes. It
verifies this on arrival in rose_route_frame and unconditionally pulls
the bytes in rose_recvmsg. The filter can trim packets to below this
value in-between, causing pull to fail, leaving the partial header at
the time of skb_copy_datagram_msg.
Place a lower bound on the size to which sk_filter may trim packets
by introducing sk_filter_trim_cap and call this for rose packets.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a tracepoint and allow user to trace messages going to and from
hardware associated with devlink instance.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Trofimovich reported that pulse audio sends SCM_CREDENTIALS
as a control message to TCP. Since __sock_cmsg_send does not
support SCM_RIGHTS and SCM_CREDENTIALS, it returns an error and
hence breaks pulse audio over TCP.
SCM_RIGHTS and SCM_CREDENTIALS are sent on the SOL_SOCKET layer
but they semantically belong to SOL_UNIX. Since all
cmsg-processing functions including sock_cmsg_send ignore control
messages of other layers, it is best to ignore SCM_RIGHTS
and SCM_CREDENTIALS for consistency (and also for fixing pulse
audio over TCP).
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: Sergei Trofimovich <slyfox@gentoo.org>
Tested-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.
Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the data plane is offloaded the traffic doesn't go through the
networking stack. Therefore, after first resolving a neighbour the NUD
state machine will transition it from REACHABLE to STALE until it's
finally deleted by the garbage collector.
To prevent such situations the offloading driver should notify the NUD
state machine on any neighbours that were recently used. The driver's
polling interval should be set so that the NUD state machine can
function as if the traffic wasn't offloaded.
Currently, there are no in-tree drivers that can report confirmation for
a neighbour, but only 'used' indication. Therefore, the polling interval
should be set according to DELAY_FIRST_PROBE_TIME, as a neighbour will
transition from REACHABLE state to DELAY (instead of STALE) if "a packet
was sent within the last DELAY_FIRST_PROBE_TIME seconds" (RFC 4861).
Send a netevent whenever the DELAY_FIRST_PROBE_TIME changes - either via
netlink or sysctl - so that offloading drivers can correctly set their
polling interval.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2 upper device needs to propagate neigh_construct/destroy calls down to
lower devices. Do this by defining default ndo functions and use them in
team, bond, bridge and vlan.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the following patch will allow upper devices to follow the call down
lower devices, we need to add dev here and not rely on n->dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_clear_hash() was invoked due to mangling of relevant headers and
BPF program needs skb->hash later on, we can add a helper to trigger hash
recalculation via bpf_get_hash_recalc().
The helper will return the newly retrieved hash directly, but later access
can also be done via skb context again through skb->hash directly (inline)
without needing to call the helper once more.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another xmit_mode to pktgen to allow testing xmit functionality
of qdiscs. The new mode "queue_xmit" injects packets at
__dev_queue_xmit() so that qdisc is called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 9b368814b3 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new event - NETDEV_CHANGE_TX_QUEUE_LEN, this
will be triggered when tx_queue_len. It could be used by net device
who want to do some processing at that time. An example is tun who may
want to resize tx array when tx_queue_len is changed.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.
This is already implemented in iproute2:
if (cmd == RTM_NEWRULE) {
req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
req.r.rtm_type = RTN_UNICAST;
}
Tested ipv4 and ipv6 with net-next linux on qemu x86
expected behavior after patch:
localhost ~ # ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0: from all lookup local
1005: from 10.46.177.97 lookup 104
32766: from all lookup main
32767: from all lookup default
There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomain
Signed-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.
It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.
Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.
bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc performance suffers when packets are dropped at enqueue()
time because drops (kfree_skb()) are done while qdisc lock is held,
delaying a dequeue() draining the queue.
Nominal throughput can be reduced by 50 % when this happens,
at a time we would like the dequeue() to proceed as fast as possible.
Even FQ is vulnerable to this problem, while one of FQ goals was
to provide some flow isolation.
This patch adds a 'struct sk_buff **to_free' parameter to all
qdisc->enqueue(), and in qdisc_drop() helper.
I measured a performance increase of up to 12 %, but this patch
is a prereq so that future batches in enqueue() can fly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing after ',', and this will introduce much more
noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the checkpatch.pl error to dev.c:
ERROR: do not initialise statics to 0
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc are changed under RTNL protection and often
while blocking BH and root qdisc spinlock.
When lots of skbs need to be dropped, we free
them under these locks causing TX/RX freezes,
and more generally latency spikes.
This commit adds rtnl_kfree_skbs(), used to queue
skbs for deferred freeing.
Actual freeing happens right after RTNL is released,
with appropriate scheduling points.
rtnl_qdisc_drop() can also be used in place
of disc_drop() when RTNL is held.
qdisc_reset_queue() and __qdisc_reset_queue() get
the new behavior, so standard qdiscs like pfifo, pfifo_fast...
have their ->reset() method automatically handled.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sch_atm returns this when TC_ACT_SHOT classification occurs.
But all other schedulers that use tc_classify
(htb, hfsc, drr, fq_codel ...) return NET_XMIT_SUCCESS | __BYPASS
in this case so just do that in atm.
BATMAN uses it as an intermediate return value to signal
forwarding vs. buffering, but it did not return POLICED to
callers outside of BATMAN.
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always mixed in the parent pointer into the dentry name hash, but we
did it late at lookup time. It turns out that we can simplify that
lookup-time action by salting the hash with the parent pointer early
instead of late.
A few other users of our string hashes also wanted to mix in their own
pointers into the hash, and those are updated to use the same mechanism.
Hash users that don't have any particular initial salt can just use the
NULL pointer as a no-salt.
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a bpf_check_basics_ok() and reject filters that are of invalid
size much earlier, so we don't do any useless work such as invoking
bpf_prog_alloc(). Currently, rejection happens in bpf_check_classic()
only, but it's really unnecessarily late and they should be rejected
at earliest point. While at it, also clean up one bpf_prog_size() to
make it consistent with the remaining invocations.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the stack's xmit_recursion limit for calls into dev_queue_xmit().
Currently, they are not handeled by the limiter when attached to clsact's
egress parent, for example, and a buggy program redirecting it to the
same device again could run into stack overflow eventually. It would be
good if we could notify an admin to give him a chance to react. We reuse
xmit_recursion instead of having one private to eBPF, so that the stack's
current recursion depth will be taken into account as well. Follow-up to
commit 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper") and
27b29f6305 ("bpf: add bpf_redirect() helper").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:168: warning: No description found for parameter 'running'
.//include/linux/netdevice.h:1867: warning: No description found for parameter 'qdisc_running_key'
Fixes: f9eb8aea2a ("net_sched: transform qdisc running bit into a seqcount")
Fixes: edb09eb17e ("net: sched: do not acquire qdisc spinlock in qdisc/class stats dump")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"make htmldocs" complains otherwise:
.//net/core/gen_stats.c:65: warning: No description found for parameter 'padattr'
.//net/core/gen_stats.c:101: warning: No description found for parameter 'padattr'
Fixes: 9854518ea0 ("sched: align nlattr properly when needed")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in kdump kernel, reduce memory usage by only using a single Queue
Set for multiqueue devices. So make netif_get_num_default_rss_queues()
return one, when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_net_device_by_node() function is defined in
<linux/of_net.h> but not included in the .c file that
implements it. Fix the following warning by including the
header:
net/core/net-sysfs.c:1494:19: warning: symbol 'of_find_net_device_by_node' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large tc dumps (tc -s {qdisc|class} sh dev ethX) done by Google BwE host
agent [1] are problematic at scale :
For each qdisc/class found in the dump, we currently lock the root qdisc
spinlock in order to get stats. Sampling stats every 5 seconds from
thousands of HTB classes is a challenge when the root qdisc spinlock is
under high pressure. Not only the dumps take time, they also slow
down the fast path (queue/dequeue packets) by 10 % to 20 % in some cases.
An audit of existing qdiscs showed that sch_fq_codel is the only qdisc
that might need the qdisc lock in fq_codel_dump_stats() and
fq_codel_dump_class_stats()
In v2 of this patch, I now use the Qdisc running seqcount to provide
consistent reads of packets/bytes counters, regardless of 32/64 bit arches.
I also changed rate estimators to use the same infrastructure
so that they no longer need to lock root qdisc lock.
[1]
http://static.googleusercontent.com/media/research.google.com/en//pubs/archive/43838.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Kevin Athey <kda@google.com>
Cc: Xiaotian Pei <xiaotian@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a single bit (__QDISC___STATE_RUNNING)
in sch->__state, use a seqcount.
This adds lockdep support, but more importantly it will allow us
to sample qdisc/class statistics without having to grab qdisc root lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
