Currently the error checking logic in the dp_debug module could
pass zero to PTR_ERR and it causes the below kbot warnings:
drivers/gpu/drm/msm/dp/dp_debug.c:378 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:387 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:396 dp_debug_init()
warn: passing zero to 'PTR_ERR'
drivers/gpu/drm/msm/dp/dp_debug.c:405 dp_debug_init()
warn: passing zero to 'PTR_ERR'
Debugfs functions are not supposed to be checked in the normal
case so delete this code. Also it silences the above Smatch
warnings that we're checking for NULL when these functions only
return error pointers.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1614971839-2686-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Set the flag vblank_disable_immediate = true to turn off vblank irqs
immediately as soon as drm_vblank_put is requested so that there are
no irqs triggered during idle state. This will reduce cpu wakeups
and help in power saving.
To enable vblank_disable_immediate flag the underlying KMS driver
needs to support high precision vblank timestamping and also a
reliable way of providing vblank counter which is incrementing
at the leading edge of vblank.
This patch also brings in changes to support vblank_disable_immediate
requirement in dpu driver.
Changes in v1:
- Specify reason to add vblank timestamp support. (Rob).
- Add changes to provide vblank counter from dpu driver.
Changes in v2:
- Fix warn stack reported by Rob Clark with v2 patch.
Changes in v3:
- Move back to HW frame counter (Rob).
Changes in v4:
- Frame count mismatch was causing a DRM WARN stack spew.
DPU HW will increment the frame count at the end of
the sync, where as vblank will be triggered at the
fetch_start counter which is calculated as v_total - vfp.
This is to start fetching early for panels with low
vbp w.r.t hw latency lines.
Add logic to detect the line count if it falls between
vactive and v_total then return incremented frame count value.
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Link: https://lore.kernel.org/r/1613651746-12783-1-git-send-email-kalyan_t@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
After spending a non-negligible time trying to figure out why
dpu_kms_init() would dereference a NULL dpu_kms->pdev, it turns out that
in addition to adding the new compatible to the msm_drv of_match_table
one also need to teach add_display_components() to register the child
nodes - which includes the DPU platform_device.
Replace the open coded test for compatibles with a check against the
match data of the mdss device to save others this trouble in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210317025634.3987908-1-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
In normal cases the gem obj lock is acquired first before mm_lock. The
exception is iterating the various object lists. In the shrinker path,
deadlock is avoided by using msm_gem_trylock() and skipping over objects
that cannot be locked. But for debugfs the straightforward thing is to
split things out into a separate list of all objects protected by it's
own lock.
Fixes: d984457b31 ("drm/msm: Add priv->mm_lock to protect active/inactive lists")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
When the system is under heavy memory pressure, we can end up with lots
of concurrent calls into the shrinker. Keeping a running tab on what we
can shrink avoids grabbing a lock in shrinker->count(), and avoids
shrinker->scan() getting called when not profitable.
Also, we can keep purged objects in their own list to avoid re-traversing
them to help cut down time in the critical section further.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210401012722.527712-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
A few functions that were intentended for the perf events support are
currently declared in arch/x86/events/amd/iommu.h, which mens they are
not in scope for the actual function definition. Also amdkfd has started
using a few of them using externs in a .c file. End that misery by
moving the prototypes to the proper header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210402143312.372386-5-hch@lst.de
Signed-off-by: Joerg Roedel <jroedel@suse.de>
We should set the platform device's driver data to NULL here so that
code doesn't assume the struct drm_device pointer is valid when it could
have been destroyed. The lifetime of this pointer is managed by a kref
but when msm_drm_init() fails we call drm_dev_put() on the pointer which
will free the pointer's memory. This driver uses the component model, so
there's sort of two "probes" in this file, one for the platform device
i.e. msm_pdev_probe() and one for the component i.e. msm_drm_bind(). The
msm_drm_bind() code is using the platform device's driver data to store
struct drm_device so the two functions are intertwined.
This relationship becomes a problem for msm_pdev_shutdown() when it
tests the NULL-ness of the pointer to see if it should call
drm_atomic_helper_shutdown(). The NULL test is a proxy check for if the
pointer has been freed by kref_put(). If the drm_device has been
destroyed, then we shouldn't call the shutdown helper, and we know that
is the case if msm_drm_init() failed, therefore set the driver data to
NULL so that this pointer liveness is tracked properly.
Fixes: 9d5cbf5fe4 ("drm/msm: add shutdown support for display platform_driver")
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Krishna Manikandan <mkrishn@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Message-Id: <20210325212822.3663144-1-swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
drm_vblank_restore() exists because certain power saving states
can clobber the hardware frame counter. The way it does this is
by guesstimating how many frames were missed purely based on
the difference between the last stored timestamp vs. a newly
sampled timestamp.
If we should call this function before a full frame has
elapsed since we sampled the last timestamp we would end up
with a possibly slightly different timestamp value for the
same frame. Currently we will happily overwrite the already
stored timestamp for the frame with the new value. This
could cause userspace to observe two different timestamps
for the same frame (and the timestamp could even go
backwards depending on how much error we introduce when
correcting the timestamp based on the scanout position).
To avoid that let's not update the stored timestamp at all,
and instead we just fix up the last recorded hw vblank counter
value such that the already stored timestamp/seq number will
match. Thus the next time a vblank irq happens it will calculate
the correct diff between the current and stored hw vblank counter
values.
Sidenote: Another possible idea that came to mind would be to
do this correction only if the power really was removed since
the last time we sampled the hw frame counter. But to do that
we would need a robust way to detect when it has occurred. Some
possibilities could involve some kind of hardare power well
transition counter, or potentially we could store a magic value
in a scratch register that lives in the same power well. But
I'm not sure either of those exist, so would need an actual
investigation to find out. All of that is very hardware specific
of course, so would have to be done in the driver code.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210218160305.16711-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user specifies zero width/height cmdline mode i915 will
blow up as the fbdev path will bypass the regular fb sanity
check that would otherwise have refused to create a framebuffer
with zero width/height.
The reason I thought to try this is so that I can force a specific
depth for fbdev without actually having to hardcode the mode
on the kernel cmdline. Eg. if I pass video=0x0-8 I will get an
8bpp framebuffer at my monitor's native resolution.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190607162611.23514-2-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When DRM_TOSHIBA_TC358762 is enabled and DRM_KMS_HELPER is disabled,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for DRM_PANEL_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && DRM_KMS_HELPER [=n]
Selected by [y]:
- DRM_TOSHIBA_TC358762 [=y] && HAS_IOMEM [=y] && DRM [=y] && DRM_BRIDGE [=y] && OF [=y]
This is because DRM_TOSHIBA_TC358762 selects DRM_PANEL_BRIDGE,
without depending on or selecting DRM_KMS_HELPER,
despite that config option depending on DRM_KMS_HELPER.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222215502.24487-1-julianbraha@gmail.com
commit f011951489 ("drm/mediatek: mtk_dpi: Create connector for bridges")
broke the display support for elm device since mtk_dpi calls
drm_bridge_attach with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR
while mtk_hdmi does not yet support this flag.
Fix this by accepting DRM_BRIDGE_ATTACH_NO_CONNECTOR in bridge attachment.
Implement the drm_bridge_funcs .detect() and .get_edid() operations, and
call drm_bridge_hpd_notify() to report HPD. This provides the
necessary API to support disabling connector creation.
In addition, the field 'conn' is removed from the mtk_hdmi struct since
mtk_hdmi don't create a connector. It is replaced with a pointer
'curr_conn' that points to the current connector which can be access
through the global state.
This patch is inspired by a similar patch for bridge/synopsys/dw-hdmi.c:
commit ec971aaa67
("drm: bridge: dw-hdmi: Make connector creation optional")
But with the difference that in mtk-hdmi only the option of not creating
a connector is supported.
Fixes: f011951489 ("drm/mediatek: mtk_dpi: Create connector for bridges")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The bridge operation '.enable' and the audio cb '.get_eld'
access hdmi->conn. In the future we will want to support
the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR and then we will
not have direct access to the connector.
The atomic version '.atomic_enable' allows accessing the
current connector from the state.
This patch switches the bridge to the atomic version to
prepare access to the connector in later patches.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The page table of AMDGPU requires an alignment to CPU page so we should
check ioctl parameters for it. Return -EINVAL if some parameter is
unaligned to CPU page, instead of corrupt the page table sliently.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Xi Ruoyao <xry111@mengyan1223.wang>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
