Michael Chan says:
====================
bnxt_en: Updates for net-next.
Update to latest firmware interface, add EEE feature, unsupported SFP+
module warning, and ethtool -s improvements.
v2: Removed the GEEPROM patch and added more comments to the get_eee patch.
====================
If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings. The
unknown speed and duplex should only be used for autoneg when link is
down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the forced speed is a valid speed supported by firmware.
If not supported, return -EINVAL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver
will print an appropriate warning to reflect the SFP+ module enforcement
policy done in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver only sets bit 0 of the async_event_fwd fields.
To be compatible with the latest spec, we need to set the
appropriate event bits handled by the driver. We should be handling
link change and PF driver unload events, so these 2 bits should be
set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to get|set EEE parameters.
v2: Added comment for preserving the tx_lpi_timer value in get_eee.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.
Update copyright year to 2016.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-04-05
This series contains updates to fm10k only.
Bruce provides nearly half of the patches in the series, most of which do
general cleanup of the driver. These include semantic cleanups,
checkpatch.pl fixes, update driver to use BIT() kernel macro, use
BUILD_BUG_ON() where appropriate and use ether_addr_copy() instead of
memcpy().
Jake provides the remaining patches in the series, starting with a fix
for a possible NULL pointer deference. Next delays initialization of the
service timer and service task until late in probe(). If we do not wait,
failures in probe do not properly cleanup the service timer or service
task items which result in a kernel panic. Added better reporting during
error conditions. Fixed another possible kernel panic where we were
clearing the interrupt scheme before we freed the mailbox IRQ. Added
helper functions for setting strings and data for ethtool stats. Fixed
comment mis-spelled words.
v2: Dropped patch 3 from the original submission, until a better solution
can be worked up based on feedback from Joe Perches and David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fm10k driver used its own code for generating a default indirection
table on device load, which was not the same as the default generated by
ethtool when indir_size of 0 is passed to SRXFH. Take advantage of
ethtool_rxfh_indir_default() and simplify code to write the redirection
table to reduce some code duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
s/funciton/function to resolve a typo, and cleanup grammar on a few
comments regarding processing the VF mailboxes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err
will be used uninitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability. Skip handling of the per-queue stats as these will be
reworked in a following patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In fm10k_set_num_queues, we previously assigned the base template. This
would always be overwritten by either fm10k_set_qos_queues or
fm10k_set_rss_queues. In either case, we don't need the base values, so
we can just remove them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Minor correction in the comment to reflect the correct function name
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the driver happens to read a register during the time in which the
device is undergoing reset, it will receive a value of 0xdeadbeef
instead of a valid value. Unfortunately, the driver may misinterpret
this as a valid value, especially if it's just looking for individual
bits.
Add an explicit check for this value when we are looking for admin queue
errors, and trigger reset recovery if we find it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no real error in an unknown event from the Firmware, we're just
posting a useful FYI notice, so this patch simply removes the "Error" word.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the VFLR bit after reset processing, instead of before. This
prevents double resets on VF init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Notify VFs in the reset interrupt handler, instead of the actual
reset initiation code. This allows the VFs to get properly notified for
all resets, including resets initiated by different PFs on the same
physical device.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some error scenarios, we may find ourselves trying to remove a
non-existent timer or worktask. This causes the kernel some bit
of consternation, so don't do it.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jiri Pirko says:
====================
mlxsw: small driver update, including switchdev doc update
Ido Schimmel (3):
mlxsw: spectrum: Reduce number of supported 802.1D bridges
switchdev: Use switch ID in suggested udev rule
mlxsw: spectrum: Add support for physical port names
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Export to userspace the front panel name of the port, so that udev can
rename the ports accordingly. The convention suggested by switchdev
documentation is used:
1) Non-split: pX
2) Split: pXsY
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there can be multiple switch ASICs on the same system we should
use the switch ID in order to differentiate between them and set the
switch name (e.g. swX) accordingly.
Also, replace the order of the "Switch ID" and "Port Netdev Naming"
sections following the above change.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resources allocated for these bridges at init time cannot be later used
for other purposes. While current number is supported by the device,
it's mostly theoretical with regards to any real use case, which leads
to poor utilization of device's resources. Solve that by reducing the
number.
The long term plan is to make this value (along with others) user
configurable via devlink and write it to NVRAM, so that it can be used
during the next init. Until then we must hardcode such values.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dropping into debug mode in a failed probe, make sure that
the AdminQ is left alive for possible hand debug of driver and
firmware states.
Move the mutex_init calls earlier in probe so that if init fails,
the admin queue interface is still available for debugging purposes.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning up the interrupt handling, clean up the IRQs only if
we actually got them set up. There are a couple of error recovery
paths that were violating this and causing the kernel a bit of
indigestion.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_common.c typically uses i40e_status as a return code,
but got missed this one case.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When updating a VSI, save off the number of allocated and unallocated
VSIs as we do when adding a VSI.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the duplicate definition of I40E_MAX_USER_PRIORITY
in i40e.h that is not needed.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simple cast to fix a sparse warning.
Fixes: commit 5453205cd0 ("i40e/i40evf: Enable support for
SKB_GSO_UDP_TUNNEL_CSUM")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk Tx clean for skbs. In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0. In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case. This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.
Fixes: 1a36d7fadd ("i40e/i40evf: use logical operators, not bitwise")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The only error case is when the malloc fails, in which case the clean up
loop does nothing at all, so remove it
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet says:
====================
net: various udp/tcp changes
First round of patches for linux-4.7
Add a generic facility for sockets to be freed after an RCU grace
period, if they need to.
Then UDP stack is changed to no longer use SLAB_DESTROY_BY_RCU,
in order to speedup rx processing for traffic encapsulated in UDP.
It gives a 17 % speedup for normal UDP reception in stress conditions.
Then TCP listeners are changed to use SOCK_RCU_FREE as well
to avoid touching sk_refcnt in synflood case :
I got up to 30 % performance increase for a mono listener.
Then three patches add SK_MEMINFO_DROPS to sock_diag
and add per socket rx drops accounting to TCP.
Last patch adds rate limiting on ACK sent on behalf of SYN_RECV
to better resist to SYNFLOOD targeting one or few flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Attackers like to use SYNFLOOD targeting one 5-tuple, as they
hit a single RX queue (and cpu) on the victim.
If they use random sequence numbers in their SYN, we detect
they do not match the expected window and send back an ACK.
This patch adds a rate limitation, so that the effect of such
attacks is limited to ingress only.
We roughly double our ability to absorb such attacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
