If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/power/supply/max8997_charger.ko | grep alias
$
After this patch:
$ modinfo drivers/power/supply/max8997_charger.ko | grep alias
alias: platform:max8997-battery
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
According to the datasheet, MAX17040 has six 16-bit registers.
Register reads and writes are only valid if all 16 bits are transferred.
Any write command that is terminated early is ignored.
So it's better to change register transacton length from 8 bits to 16 bits.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
To avoid canceling the delayed workqueue needlessly, and scheduling an
immediate polling. Check if the new poll_interval value is different
than the previous setting.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
In drivers/power/supply/ab8500_fg.c, fix two typos and adjust the function
name in two cases to correspond to the names of the defined functions.
In drivers/power/supply/power_supply_core.c, change two variable names to
the names of the corresponding parameters.
Issue detected using Coccinelle (http://coccinelle.lip6.fr/)
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a driver which allows powering off the system via an Intel PIIX4
southbridge, by entering the PIIX4 SOff state. This is useful on the
MIPS Malta development board, where it will power down the FPGA based
board until its ON/NMI button is pressed, or the QEMU implementation of
the MIPS Malta board where it will cause QEMU to exit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix issue with poll_interval being not updated till the previous
interval expired.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Liam Breck <liam@networkimprov.net>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There where still a few lingering references to pdata after commit
power: supply: sbs-battery: simplify DT parsing.
Remove pdata from struct·sbs_info and conditional checks to ser if this
was set from the i2c read / write functions.
Instead of call max in each function for incrementing poll_retry_count
do it once in the probe function.
Fixup null pointer dereference in to pdata in sbs_external_power_changed.
Change retry counts to u32 to avoid need for max.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch removes support for STiH415/6 SoC's from the
st-poweroff driver, as support for these platforms is
being removed from the kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <linux-pm@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A dev_err message spans two lines and the literal string is missing
a white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
According to the Smart Battery Data Specification, the use
of ManufacturerAcess (register 0x0) is implementation-defined.
It appears that some batteries use writes to this register
in order to implement certain functionality, but others may
simply NAK all writes to it. As a result, write failures to
ManufacturerAccess should not be used as an indicator of
battery presence, nor as a failure to enter sleep mode.
The failed write access was seen with SANYO AP13J3K.
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
bq->charger is initialized in bq24257_power_supply_init.
Therefore, bq24257_power_supply_init should be called before the
registration of the IRQ handler bq24257_irq_handler_thread that calls
power_supply_changed(bq->charger).
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Cc: Aurelien Chanot <chanot.a@gmail.com>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Fixes: 2219a93596 ("power_supply: Add TI BQ24257 charger driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use a more common logging style.
Miscellanea:
o Use pr_warn
o Coalesce formats adding missing spaces
o Argument alignment
o Remove unnecessary OOM messages as k.alloc does stack dumps
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nishanth Menon <nm@ti.com>
[khilman: update shortlog]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the change to use the gpio descriptor interface, we get a warning if
-Wmaybe-uninitialized is added back to the build flags (it is currently
disabled:
drivers/power/supply/sbs-battery.c: In function 'sbs_probe':
drivers/power/supply/sbs-battery.c:760:28: error: 'pdata' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that if neither the DT properties nor a platform_data
pointer are provided, the chip->pdata pointer gets set to an uninitialized
value.
Looking at the code some more, I found that the sbs_of_populate_pdata
function is more complex than necessary and has confusing calling
conventions of possibly returning a valid pointer, a NULL pointer
or an ERR_PTR pointer (in addition to the uninitialized pointer).
To fix all of that, this gets rid of the chip->pdata pointer and
simply moves the two integers into the sbs_info structure. This
makes it much clearer from reading sbs_probe() what the precedence
of the three possible values are (pdata, DT, hardcoded defaults)
and completely avoids the #ifdef CONFIG_OF guards as
of_property_read_u32() gets replaced with a compile-time stub
when that is disabled, and returns an error if passed a NULL of_node
pointer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 3b5dd3a494 ("power: supply: sbs-battery: Use gpio_desc and sleeping calls for battery detect")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This requests the status GPIO with initial input setup. It is required
to read the GPIO status at probe time and thus correctly avoid sending
I2C messages when AC is not plugged.
When requesting the GPIO without initial input setup, it always reads 0
which causes probe to fail as it assumes the charger is connected, sends
I2C messages and fails.
While at it, this switches the driver over to gpiod API.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Switch to using new gpio_desc interface and devm gpio get calls to
automatically manage gpio resource. Use gpiod_get_value which handles
active high / low calls.
If gpio_detect is set then force loading of the driver as it is
reasonable to assume that the battery may not be present.
Update the is_present flag immediately in the IRQ.
Remove legacy gpio specification from platform data.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the power supply's current max property,
POWER_SUPPLY_PROP_CURRENT_MAX.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the power supply capacity level property, it corresponds to
POWER_SUPPLY_CAPACITY_LEVEL_*.
It also utilizes the precision voltage detector function module
to catch the low battery voltage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The power supply type property is varying as the external power
supply changes. It is not a constant.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the charger status change interrupt support, it will report
the power supply changed event.
This interrupt is generated by one of the conditions as below:
- the state machine jumps out of or into the EOC state
- the CHGIN input voltage goes out of or into the valid range.
- the battery temperature goes out of or into the valid range.
- the PRECHARGE time-out occurs.
- the total charge time-out occurs.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When get the property, first check the charger state machine,
then check the status bit to decide what value is assigned to
the corresponding property.
Retain the SUSCHG bit of REG 0x71 when configure the timers to
avoid losting the charger suspending info after boot.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove "battery_temperature" member, it is redundant, it is the
hardware's responsibility to handle TH pin properly.
It is unnecessary to use the dt property to check if there is
a battery temperature monitor or not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since the act8945a_charger is regarded as a sub-device, all properties will
be assigned to its own device node. All properties can be achieved from its
own node, instead of from its parent device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When the charger is missing (disconnected), it is safe to assume that
the charger chip is no charging.
This is especially relevant when a status GPIO is present and the
charger is getting disconnected. bq24735_charger_is_charging will be
triggered due to the interrupt then, it will attempt to read whether it
is charging through i2c, which will fail as the charger is disconnected.
This also fixes that specific issue.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "monitor_wqueue" is used to monitor the battery
status. It has been identity converted.
It queues multiple work items viz &di->monitor_work,
&di->set_charged_work, which require execution ordering.
Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "fg_wq" is used for running the FG algorithm periodically.
It has been identity converted.
It has multiple work items viz fg_periodic_work, fg_low_bat_work,
fg_reinit_work, fg_work, fg_acc_cur_work and fg_check_hw_failure_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has been set to guarantee forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "wq" is used for handling battery related tasks.
It has a single work item viz &mb->update and hence it doesn't require
execution ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for the IRQs and checking HW state of
the charger. It has been identity converted.
It has multiple work items viz usb_charger_attached_work, kick_wd_work,
check_vbat_work, check_hw_failure_work, usb_charger_attached_work,
ac_work, ac_charger_attached_work, attach_work and check_usbchgnotok_work,
which require execution ordering. Hence, a dedicated ordered workqueue
has been used here.
The WQ_MEM_RECLAIM flag has also been set to ensure
forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "monitor_wqueue" is used to monitor the PMIC battery status.
It queues a single work item (pbi->monitor_battery) and hence doesn't
require ordering. Hence, alloc_workqueue has been used to replace the
deprecated create_singlethread_workqueue instance.
Since PMIC battery status needs to be monitored for any change, the
WQ_MEM_RECLAIM flag has been set to ensure forward progress under memory
pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "charger_wq" is used for running all the charger related
tasks. This involves charger detection, checking for HW failure and HW
status. This workqueue has been identity converted.
It queues multiple workitems viz &pm2->check_main_thermal_prot_work,
&pm2->check_hw_failure_work, &pm2->ac_work. Hence, the deprecated
create_singlethread_workqueue() instance has been replaced with a
dedicated ordered workqueue.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The workqueue "btemp_wq" is used for measuring the temperature
periodically. It queues a single workitem (btemp_periodic_work) and
hence doesn't require ordering. Thus, the deprecated
create_singlethread_workqueue() instance has been replaced with
alloc_workqueue().
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure.
Since there is a single work item, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
alloc_ordered_workqueue() with WQ_MEM_RECLAIM set replaces
deprecated create_singlethread_workqueue(). This is the identity
conversion.
The workqueue "chargalg_wq" is used for running the charging algorithm.
It has multiple workitems viz &di->chargalg_periodic_work,
&di->chargalg_wd_work, &di->chargalg_work per abx500_chargalg, which
require ordering. It has been identity converted.
Also, WQ_MEM_RECLAIM has been set to ensure forward progress under
memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the managed resource version of reboot_mode_register().
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Provide managed resource version of reboot_mode_register() and
reboot_mode_unregister() to simplify implementations.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Battery capacity level is a standard feature of sbs battery
That can be used to tell what the remainig battery capacity is, and
can tell if the battery has not been calibrated/initialized, which makes
the capacity and charging/discharging percentages invalid.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add missing platform_set_drvdata() in tps65217_charger_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Fixes: 3636859b28 ("power_supply: Add support for tps65217-charger")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_power_supply_register instead of power_supply_register.
Remove call to power_supply_unregister.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently the battery detect gpio can not be used with a chained interrupt
controller that requires threaded irq handlers. Use threaded irq instead.
In addition this was not going to be working at present because
chip->power_supply is assigned after the request irq call.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use devm_kzalloc to allow memory to be freed automatically on
driver probe failure or removal.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The bq27000 and bq27010 have a single byte FLAGS register.
Other gauges have 16 bit FLAGS registers.
For reading the FLAGS register it is sufficient to read the single
register instead of reading RSOC at the next higher address as
well and then ignore the high byte.
This does not change functionality but optimizes i2c and hdq
traffic.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make use of IRQ resources defined in tps65217 mfd code. If they are valid
we use them instead separate poll task, in order to define AC power state.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
