In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reason station id and tid fields are both in baid data and
in the reorder buffer per queue is that we couldn't access the
baid_data in the reorder timer functions.
Now that we do some pointer math and access it anyway, those
fields can be removed.
This save some space and some code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we may have up to 256 entries per reorder buffer, and possibly up
to 16 queues, we can use a LOT of memory for this (64k for each station).
Allocate it according to what we need, which is of course much less for HT
stations (only 16k at a max of 16 queues).
However, this comes at the expense of complicating the code a bit to
calculate the right entry structure to use for each frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger that collects data when a frame is released
because of the timer of the reordering buffer was not
implemented for 9000 devices.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always need to initialize the status argument to the success case
before calling iwl_mvm_send_cmd_status() or
iwl_mvm_send_cmd_pdu_status() (which calls the former) otherwise we
may get an uninitialized value back. In this case, we use
ADD_STA_SUCCESS as success.
Fixes: 732d06e9d9 ("iwlwifi: mvm: add station before allocating a queue")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_add_bcast_sta() and the iwl_mvm_rm_bcast_sta() functions
are only called in P2P flows. Add _p2p_ to the function names to make
this explicit.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d3 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API allows flushing queues based on station ID and TID in A000
devices. One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.
In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.
This bug has been fixed on 9000 devices and up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
-----BEGIN PGP SIGNATURE-----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=oYeO
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore. Mistakenly, this was changed to return an
error while fixing another bug.
If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.
Fixes: cd4d23c1ea ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we have 512 queues, add a wait for single TX
queue to gen2.
This replaces gen1 wait_tx_queues_empty, which was limited
to 32 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The function flushed only agg queue and no more traffic
is queued on it.
However, it waits for all queues to empty, which is not
necessary and may take more time.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid using the global flush and move to flush per
station whenever possible in DQA mode.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename current wait_tx_queue_empty to wait_tx_queues_empty since
it waits for multiple queues (up to 32).
Next patch will add a wait for single TX queue which is needed for
gen2 to be scalable for 512.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support change to ADD_STA API to support station types.
Each station is assigned its type.
This simplifies FW handling of the broadcast and multicast
stations:
* broadcast station is identified by its type and not the mac
address.
* multicast queue is no longer treated differently. The opening
and closing of it is done by referring to its station.
There is no need to specify it in the MAC command.
* When disabling TX to all station driver can disable the traffic
on multicast station, so FW doesn't have to do it.
Change is backward compatible.
Change the order of adding and removing the stations according to
FW requirements.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the fields aren't needed in new TX path.
Enlarging the struct to 512 queues will consume a lot of memory.
Remove all references to the struct in the new TX path.
Move mac80211 queue mapping outside, since it will be needed per
queue for TVQM mode.
Add warning in paths that shouldn't be hit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't use IEEE80211_INVAL_HW_QUEUE to mark a queue as
invalid since 255 will be a valid value for a TVQM queue
index.
Use IWL_MVM_INVALID_QUEUE instead for accessing txq_id.
reserved_queue can stay a u8 since reserved_queue is not
used when TVQM is enabled.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
cab_queue can now get bigger than u8, since in TVQM we will support
512 queues..
Support it by maintaining internal mapping between the actual number
and mac80211 queue (IWL_MVM_DQA_GCAST_QUEUE).
For pre-a000 the internal queue will be the same as the mac80211
queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reserved queue is never used, save the trouble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove an extra variable 'queue' that already exists.
Also, since there are no code paths that use 'queue'
without intializing it, remove the unnecessary zero
initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While freeing inactive queue, check mvmsta to be valid before
dereferencing it. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the end, the firmware doesn't want the SP len as present
in the WMM IE, but rather the actual number of frames.
Fixes: bd3c6cf901a8 ("iwlwifi: mvm: tell the firmware about the U-APSD parameters")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get SN that is smaller than SSN of the aggregation,
we shouldn't apply any reordering on them.
Further more, HW NSSN will be zeroed, which can cause us
to make some invalid decisions.
Detect the situation and invalidate the BAID.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In TVQM firmware returns the value of the queue ID and code
should accept it.
The TX queue config API was changed. Move to new API.
This has to be done in parallel in mvm and pcie.
Do not move yet to 512 queues since there are some opens
with enabling it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer firmware versions will be able to handle all the
WMM-PS flows internally when we act as a GO. The firwmare
relies on the fact that the drivers puts frames for
different peers in different queues (DQA) to achieve this.
The driver will not be aware of the power state of the peers
anymore.
Tell the firmware about the WMM-PS parameters of earch peer
that connects to us so that it can know what are the
trigger-enabled ACs, the delivery-enableds ACs and the
Service Period length.
This API change is backward compatible since older firmware
versions will simply ignore the newly added values.
Since we don't support ieee80211 TSPECs for now, just copy
the trigger-enabled ACs to the delivery enabled ones.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.
In addition, due to SN offload having TX queue shared between TIDs
is impossible
Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.
From driver perspective we have here a new design:
Queue sharing and inactivity checks are disabled.
Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently aux & broadcast queues are added before calling add
station, which results with a SCD_QUEUE_CFG command sent with
a station id unknown yet to fw.
While this works for pre-a000 firmware, the a000 fw requires
the order to be reversed.
The reason the change is only for a000 devices and not for
previous devices is that we cannot reverse the order since
the tfd_queue_mask containing the aux queue will cause FW to
assert on adding a queue mask with a queue that is not enabled.
This is not a problem in a000 fw since the tfd_queue_mask was
removed from the add sta API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some small fixes here and there;
* The usual cleanups and small improvements;
* Work to support A000 devices continues;
* New FW API version;
* Some debugging improvements;
-----BEGIN PGP SIGNATURE-----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=iKI9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Patches intended for v4.12:
* Some small fixes here and there;
* The usual cleanups and small improvements;
* Work to support A000 devices continues;
* New FW API version;
* Some debugging improvements;
In a000 devices FW will assign the queue number. Prepare for
that by getting rid of static defines and store them in variables.
Enlarge to u16 since we may have up to 512 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The command was changed to support PN offload and TKIP offload.
The FW will do TKIP calculations in D0 only for a000 devices,
but API is aligned anyway.
However, for all devices we can stop sending the wowlan tkip
command.
Firmware will fetch the keys from the station key command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multicast queue is associated with the broadcast
station.
This raises quite a few issues:
The multicast queue has a special treatment:
- It is sent in the MAC context command
- It is excluded from tfd_queue_mask
In DQA mode we end up enabling two queues - the probe response
queue and the multicast queue - with the same station (broadcast)
and TID while in DQA mode it should be unique RA-TID.
Firmware will enforce it for a000 devices, so this allocation
will fail.
In addition, in a000 devices the FW will set the FIFO and not
the driver. So there is a need for FW to know when we enable
the queue that it is multicast queue so it will be bound to
the multicast FIFO. There is no such way in current design.
In order to simplify driver and firmware handling of this queue
create a multicast station.
This solves the unique RA-TID issue in the short term and serves
as preparation for the long term.
In the long term we will also add a flag marking this station for
the FW as the multicast station.
Once we will do that the FW will know this is the multicast queue
immediately when it is added and bind it to the correct FIFO.
It will also enable removing the special treatment of the
queue in the MAC context command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYnHNpAAoJEG4XJFUm622b48QH/iQ7eCZMSYBOb3QIqJnpEkD/
k1xtch60J/JBTw11mS8TvvqyA19BnLZmLIIbbVWLTPeL5S4MJBGmEISHE9dc3FmY
CP//GjQYdxSm7VgZJSUKolQOIsY4kj/WuY4eoJzWiOfaloXHk0ascNrigdXCUSec
lRM8sX77KY/30qKJGN/Yc1ccT8zmRa/Skdt7JSHzNKakHiykqvR6NgRa6stf3g5K
NJAIrZO7K1Yndr187EsX4mr3ataAeo5+YHxoIReuYq2pcrZ6uSDsO3tJfC+4upqR
SrN/x6ds5SUYCKfwy0i/oxwuzYb8hWFH0m+yXhdkNPoaIyhgGHqzCVzdzbaqcDw=
=IyB5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing an IGTK, iwl_mvm_send_sta_igtk() was
called before station ID was retrieved, so the function
was invoked with an invalid station ID. Fix this by first
getting the station ID.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192411
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.
Fixes: 9794c64f30 ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing inactive queue - use the central disable queue
function. This is needed due to a000 changes to come, but is
a proper cleanup anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the sta_id variable, to avoid this compile warning when
compiling with W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c: In function ‘iwl_mvm_change_queue_owner’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c:871:5: warning: variable ‘sta_id’ set but not used [-Wunused-but-set-variable]
s8 sta_id;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware restarts in a situation in which any station
has no queue reserved anymore because that queue was used, the
code will crash trying to access the queue_info array at the
offset 255, which is far too big. Fix this by checking that a
queue is actually reserved before writing its status.
Fixes: 8d98ae6eb0 ("iwlwifi: mvm: re-assign old queues after hw restart in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a peer associates, the firmware will soon want to know
its AID to be able to compute the TIM IE by itself.
In DQA, the firmware has all the information it needs to
update the TIM internally. The only missing part is the
AID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When using RSS on 9000 series devices, we can't rely on processing the
received frames for station powersave handling, since they could be
processed on different CPUs and out of order.
In order to still manage the powersave of stations, the firmware sends
a notification on sleep->wake, wake->sleep and - for U-APSD - frames
received with PM while already sleeping (with the TID.)
With this, the driver can set AP_LINK_PS, which is required for real
parallel RX. In addition, this requires checking for PS-Poll frames
and calling ieee80211_sta_pspoll() appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA has deferred traffic to TX, an appropriate bit
is turned on in %deferred_tx_frames to indicate deferred
traffic. This marking is never turned off, resulting in
iterating over TIDs with no deferred traffic.
Although this didn't cause any failures/errors/bugs, there
is still no point of iterating over these TIDs when not
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a TXQ's marking as a reserved queue is removed,
when removing the STA the driver might try to access
out of bounds memory. Make sure the reserved queue
is freed only if it is still reserved.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a TXQ's owner is changed, the FW is indeed notified, but
the driver doesn't update the current metadata to reflect the
owner change. Fix that.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we unshare a queue, the ADD_STA was not properly
initialised.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in making this an out-of-line function
since it just calls a single other function with a few
changed parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use setup_timer function instead of initializing timer with the function
and data fields
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA is removed in DQA mode, if no traffic went through
its reserved queue, the txq continues to be marked as
reserved and no STA can use it.
Make sure that in such a case the reserved queue is marked
as free when the STA is removed.
Fixes: commit 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the SCD_QUEUE_CFG command was introduced the driver
calls iwl_trans_txq_enable_cfg() with a NULL for scd_cfg
parameter.
This makes the transport avoid writing to the SCD pointers,
since it can cause races with firmware, which is also accessing
the registers.
The transport only updates the write pointer in that case.
Fix a wrong call to iwl_trans_txq_enable() which caused a
scd_cfg parameter to be sent to transport, resulting with an
access to SCD registers.
Fixes: 58f2cc57dc ("iwlwifi: mvm: support dqa-mode scd queue redirection")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Every active TXQ is assigned to a TID given through the
SCD_CONFIG_CMD, and acts as an identifier in the FW. However,
there may be cases this ownership needs to be changed.
For example, in the following scenario:
1. TID x is owner of a queue
2. Due to a shortage of queues, TID y and z share with x
3. TID x becomes inactive and needs to be removed from the
shared queue.
In this scenario, if another queue is freed and traffic on x
continues, we can't allocate it a new queue as long as it is
the owner of the first queue.
Support moving ownership of a TXQ to a different TID (same
STA) without stopping the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to the addition of another option in the SCD_CONFIG_CMD's
%enable field, change the assignment of this field to use
defines rather than hard-code the value itself.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When working in DQA mode, if a queue is shared and a HW restart
occurs, there might be a possible race condition between
stations on the queues, and an existing queue might be left
with no queues.
To solve this, make sure in DQA mode to re-assign the same
queues as before the HW restart.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending the SCD_QUEUE_CONFIG command, the queue is
associated to a specific TID. If later there is a need to
use this TID on a different queue instead, it first needs to
be unassociated from the first queue.
Keep track for every queue what TID is associated with it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a shared queue becomes unshared, aggregations should be
re-enabled if they've existed before. Make sure that they do
this, if required.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for installing and removing GMAC key
for newer FW versions that support GCM and MFP.
GMAC provides authentication and integrity for multicast management
frames.
Firmware API was changed, update the driver accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
