In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
setup_timer() was already being called before the open-coded init_timer()
and .data assignment. These are removed as well.
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Per the IBTA spec, QP destroy shall fail if the QP is attached
to multicast groups, although the spec is silent on modify_qp
to reset state. It implies that ULP must deregister QP from
all mcast groups for destroy to succeed.
The faulty patch "IB/ipoib: Update broadcast object if PKey value
was changed in index 0" exposed two issues in rdmavt:
1. Rvt QP reset waits for qp references to go to zero.
This will hang if QP is attached to multicast groups.
2. The mcast group detach will fail for a QP in reset state
therefore preventing ULP from correcting the issue.
This patch moves the reference count wait to the the destroy QP
path and allows a QP mcast detach to work in the reset state.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A destroy of an MR prior to destroying the QP can cause the following
diagnostic if the QP is referencing the MR being de-registered:
hfi1 0000:05:00.0: hfi1_0: rvt_dereg_mr timeout mr ffff8808562108
00 pd ffff880859b20b00
The solution is to when the a non-zero refcount is encountered when
the MR is destroyed the QPs needs to be iterated looking for QPs in
the same PD as the MR. If rvt_qp_mr_clean() detects any such QP
references the rkey/lkey, the QP needs to be put into an error state
via a call to rvt_qp_error() which will trigger the clean up of any
stuck references.
This solution is as specified in IBTA 1.3 Volume 1 11.2.10.5.
[This is reproduced with the 0.4.9 version of qperf and the rc_bw test]
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There are currently 3 spots in the qib and hfi1 driver that have
knowledge of the internal QP hash list that should only be in
scope to rdmavt QP code.
Add an iterator API for processing all QPs to hide the
nature of the RCU hashlist.
The API consists of:
- rvt_qp_iter_init()
* For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter_next()
* For iterating QPs one at a time for seq_file semantics
- rvt_qp_iter()
* For iterating all QPs
The first two are used for things like seq_file prints.
The last is for code that just needs to iterate all QPs
in the system.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
hfi1 and qib were converted in previous patches, do the same for rdmavt.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rvt_check_ah() delegates lid verification to underlying
driver. Underlying driver uses different conditions to
check for dlid depending on whether the device supports
extended LIDs
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The pmtu field doens't have be stored in the QP structure
as it can easily be calculated when needed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure we can't come up with an array size that is bigger than the array
by applying the QPN mask before the divide in the free_qpn function.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The free_qpn() function from the hfi1/qib driver which was the basis for
rdmavt_free_qpn() function was accidentally left in the code. Remove it.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
SGEs that are contiguous needlessly consume driver dependent TX resources.
The lkey validation logic is enhanced to compress the SGE that ends
up in the send wqe when consecutive addresses are detected.
The lkey validation API used to return 1 (success) or 0 (fail).
The return value is now an -errno, 0 (compressed), or 1 (uncompressed). A
additional argument is added to pass the last SQE for the compression.
Loopback callers always pass a NULL to last_sge since the optimization is
of little benefit in that situation.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify core and driver components to use accessor functions
introduced to access individual fields of rdma_ah_attr
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The wqe should be read only and in fact the superfluous reset of the
RVT_SEND_RESERVE_USED flag causes an issue where reserved operations
elicit a bad completion to the ULP.
The maintenance of the flag is now entirely within rvt_post_one_wr()
where a reserved operation will set the flag and a non-reserved operation
will insure the operation that is about to be posted has the flag reset.
Fixes: Commit 856cc4c237 ("IB/hfi1: Add the capability for reserved operations")
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RC timeout counter isn't getting incremented.
Increment counter and add the trace for it.
Fixes: 87c23b4ab018 ("IB/rdmavt: Adding timer logic to rdmavt")
Reviewed-by: Brian Welty <brian.welty@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix is to get additional debugging information.
The following fields are added:
- wqe
- qpt
- num_sge
- ssn
- pid
- send_flags
These additional fields provide for more focused filtering
and triggering.
The patch also moves the trace to just before the wqe is
posted to get the most accurate information and future proofs
the code to trace all possible reserved opcodes.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The work to create a completion helper moved the translation of send
wqe operations to completion opcodes to rdmvat.
This precludes having driver dependent operations. Make the translation
driver dependent by doing the translation in the driver prior to the
rvt_qp_swqe_complete() call using restored translation tables.
Fixes: Commit f2dc9cdce8 ("IB/rdmavt: Add a send completion helper")
Fixes: Commit 0771da5a6e ("IB/hfi1,IB/qib: Use new send completion helper")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rename RVT AETH defines and export in rdma/ib_hdrs.h
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return usec from an index into ib_rvt_rnr_table.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To move common code across target to rdmavt for code reuse.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add rvt_rc_error() and rvt_comm_est() as shared functions in
rdmavt, moved from hfi1/qib logic.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rvt_create_qp() creates qp->ip only when a qp creation request comes from
userspace (udata is not NULL). If we exceed the number of available
queue pairs however, the error path always attempts to put a kref to this
structure. If the requestor is inside the kernel, this leads to a crash.
We fix this by checking that qp->ip is not NULL before caling kref_put().
Signed-off-by: Jim Foraker <foraker1@llnl.gov>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is for use by client drivers to drive
send completions into a CQ.
A new exported table allows for the mapping
of ib_wr_opcode into a ib_wc_opcode.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Corrected function name in comment from qib_ to rvt_.
Signed-off-by: Parav Pandit <pandit.parav@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds lockdep asserts in key code paths for
insuring lock correctness.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add an rvt_qp_init() to initialize specific
common fields as the qp is created or reset.
The routine is shared by the rvt_reset_qp() and
the rvt_create_qp().
The intent is that lock dep assertions will only
appear in the rvt_reset_qp().
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The reset calldown is misplaced.
It should only be called in the code that actually
transitions the QP to reset.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The __must_hold() is sufficent to correct the sparse
context imbalance inside a function.
Per Documentation/sparse.txt:
__must_hold - The specified lock is held on function entry and exit.
Fixes: Commit c0a67f6ba3 ("IB/rdmavt: Annotate rvt_reset_qp()")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This improves readability and hides the reference count
mechanism from the client drivers.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The unwind logic for creating a user QP has a double vfree
of the non-shared receive queue when handling a "too many qps"
failure.
The code unwinds the mmmap info by decrementing a reference
count which will call rvt_release_mmap_info() which in turn
does the vfree() of the r_rq.wq. The unwind code then does
the same free.
Fix by guarding the vfree() with the same test that is done
in close and only do the vfree() if qp->ip is NULL.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The use of the specific opcode test is redundant since
all ack entry users correctly manipulate the mr pointer
to selectively trigger the reference clearing.
The overly specific test hinders the use of implementation
specific operations.
The change needs to get rid of the union to insure that
an atomic value is not seen as an MR pointer.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hanging has been observed while writing a file over NFSoRDMA. Dmesg on
the server contains messages like these:
[ 931.992501] svcrdma: Error -22 posting RDMA_READ
[ 952.076879] svcrdma: Error -22 posting RDMA_READ
[ 982.154127] svcrdma: Error -22 posting RDMA_READ
[ 1012.235884] svcrdma: Error -22 posting RDMA_READ
[ 1042.319194] svcrdma: Error -22 posting RDMA_READ
Here is why:
With the base memory management extension enabled, FRMR is used instead
of FMR. The xprtrdma server issues each RDMA read request as the following
bundle:
(1)IB_WR_REG_MR, signaled;
(2)IB_WR_RDMA_READ, signaled;
(3)IB_WR_LOCAL_INV, signaled & fencing.
These requests are signaled. In order to generate completion, the fast
register work request is processed by the hfi1 send engine after being
posted to the work queue, and the corresponding lkey is not valid until
the request is processed. However, the rdmavt driver validates lkey when
the RDMA read request is posted and thus it fails immediately with error
-EINVAL (-22).
This patch changes the work flow of local operations (fast register and
local invalidate) so that fast register work requests are always
processed immediately to ensure that the corresponding lkey is valid
when subsequent work requests are posted. Local invalidate requests are
processed immediately if fencing is not required and no previous local
invalidate request is pending.
To allow completion generation for signaled local operations that have
been processed before posting to the work queue, an internal send flag
RVT_SEND_COMPLETION_ONLY is added. The hfi1 send engine checks this flag
and only generates completion for such requests.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix allows for support of in-kernel reserved operations
without impacting the ULP user.
The low level driver can register a non-zero value which
will be transparently added to the send queue size and hidden
from the ULP in every respect.
ULP post sends will never see a full queue due to a reserved
post send and reserved operations will never exceed that
registered value.
The s_avail will continue to track the ULP swqe availability
and the difference between the reserved value and the reserved
in use will track reserved availabity.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some work requests are local operations, such as IB_WR_REG_MR and
IB_WR_LOCAL_INV. They differ from non-local operations in that:
(1) Local operations can be processed immediately without being posted
to the send queue if neither fencing nor completion generation is needed.
However, to ensure correct ordering, once a local operation is posted to
the work queue due to fencing or completion requiement, all subsequent
local operations must also be posted to the work queue until all the
local operations on the work queue have completed.
(2) Local operations don't send packets over the wire and thus don't
need (and shouldn't update) the packet sequence numbers.
Define a new a flag bit for the post send table to identify local
operations.
Add a new field to the QP structure to track the number of local
operations on the send queue to determine if direct processing of new
local operations should be enabled/disabled.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change rvt_post_one_wr to use the new table mechanism for
post send.
Validate that each low level driver specifies the table.
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add flexibility for driver dependent operations in post send
because different drivers will have differing post send
operation support.
This includes data structure definitions to support a table
driven scheme along with the necessary validation routine
using the new table.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current drivers return errors from this calldown
wrapped in an ERR_PTR().
The rdmavt code incorrectly tests for NULL.
The code is fixed to use IS_ERR() and change ret according
to the driver return value.
Cc: Stable <stable@vger.kernel.org> # 4.6+
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since rvt_reset_qp already zero's out qp->s_ack_queue head and tail
pointers, there is no need to zero out qp->s_ack_queue itself.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Correct calculation of the low order bits which should be unset
based on use of qos_shift parameter when assigning QPN.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch avoids that sparse reports the following warning:
rdmavt/qp.c:507:17: warning: context imbalance in 'rvt_reset_qp' - unexpected unlock
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdmavt allows the driver to specify the size of the ack queue, but
only uses it for the modify QP limit testing for setting the atomic
limit value.
The driver dependent size is now used to size the s_ack_queue ring
dynamicially.
Since the driver knows its size, the driver will use its define
for any ring size dependent code.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The usage of the various vmalloc APIs do not consistently zero memory
when allocating the swqe. Insure zeroing variants are used.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The awkward coding for setting the allowed_ops field
was tripping an smatch warning.
This patch uses the more appropriate defines from include/rdma
to avoid the issue.
As part of the patch remove a mask that was duplicated
in rdmavt include files and use that mask as appropriate.
Fixes: 8bea6b1cfe6f ("IB/rdmavt: Add create queue pair functionality")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
call_send is used to determine whether to send immediately or schedule
a send for later. The current logic in rdmavt is inverted and has a
negative impact on the latency of the hfi1 and qib drivers. Fix this
regression by correctly calling send immediately when call_send is set.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Accordingly IB Spec post WR to receive queue must
complete with error if QP is in Error state.
Please refer to C10-42, C10-97.2.1
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tracking user/QP ownership is needed to debug issues with
user ULPs like OpenMPI.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The non-rdamvt versions of qib and hfi1 allow for a differing
heuristic to override a schedule progress in favor of a direct
call the the progress routine.
This patch adds that for both drivers and rdmavt.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove exported functions which are no longer required as the
functionality has moved into rdmavt. This also requires re-ordering some
of the functions since their prototype no longer appears in a header
file. Rather than add forward declarations it is just cleaner to
re-order some of the functions.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While hfi1 and qib were still supporting bits and pieces of core verbs
components there needed to be a way to convey if rdmavt should handle
allocation and initialize of resources like the queue pair table. Now
that all of this is moved into rdmavt there is no need for these flags.
They are no longer used in the drivers.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add, remove, and otherwise clean up existing comments that are leftover
from the initial code postings of rdmavt. Many of the comments were added
to provide an idea on the direction we were thinking of going. Now that the
design is solidified make a pass over and clean everything up. Also add
details where lacking.
Ensure all non static functions have nano comments.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These trace and error print statements would help in debugging issues which
are caused due to messed up QP ring buffer pointers.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds an additional lock to reduce contention on the s_lock.
This lock is used in post_send() so that the post_send is not
serialized with the send engine and other send related processing.
To do this the s_next_psn is now maintained on post_send() while
post_send() related fields are moved to a new cache line. There is
an s_avail maintained for the post_send() to mitigate trading cache
lines with the send engine. The lock is released/acquired around
releasing the just built packet to the egress mechanism.
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A busy_jiffies variable is maintained and updated when rc qps are
created and deleted. busy_jiffies is a scaled value of the number
of rc qps in the device. busy_jiffies is incremented every rc qp
scaling interval. busy_jiffies is added to the rc timeout
in add_retry_timer and mod_retry_timer. The rc qp scaling interval
is selected based on extensive performance evaluation of targeted
workloads.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Vennila Megavannan <vennila.megavannan@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use the new RNR timer for hfi1.
For qib, this timer doesn't exist, so exploit driver
callbacks to use the new timer as appropriate.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In addition to removing the modify queue pair verb from hfi1 we also
remove ancillary functions which existed only for modify queue pair and
are also already present in hfi1.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
alloc_qpn must use GFP and the hardware drivers should use it as well.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB core uses 1 relative indexing for ports. All of our data structures
use 0 based indexing. Add an inline function that we can use whenever we
need to validate a legal value and try to convert a port number to a
port index at the entrance into rdmavt.
Try to follow the policy that when we are talking about a port from IB
core point of view we refer to it as a port number. When port is an
index into our arrays refer to it as a port index.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change verbs memory allocations to the device numa node. This keeps memory
close to the device for optimal performance.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some hardware drivers requires additional checks on send WRs. Create an
optional call back to allow hardware drivers to reject a send WR.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fill in srq function stubs with code derived from hfi1 and qib.
Move necessary functions and data structure members as well.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Drivers using rdmavt can rely on rvt_query_qp instead of defining their own
query_qp functions.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update all files added by rdmavt which do not yet have 2016 as the
copyright year.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Low level drivers need to be able to check incoming attributes as well as be
able to adjust their private data on queue pair modification. Add 2 driver
callbacks, check_modify_qp and modify_qp, to facilitate this.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds in the multicast add and remove functions as well as the
ancillary infrastructure needed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds the simple post receive verbs call to rdmavt. The actual
interrupt handling and packet processing is still done in the low level
driver.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds in support the qp destroy verb call.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add in a post_send and post_one_send to rdmavt. The ULP will provide a WQE
to rdmavt which will then walk and queue each element. Rdmavt will then
queue the work to be done in the driver or kick the driver's progress
routine.
There needs to be a follow on patch which adds in another lock for the
head of the queue so that it can be added to and read from in parallel.
This will touch protocol handlers and require other changes in the
drivers. This will be done separately.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current code is problematic when the QP creation and ipoib is
used to support NFS and NFS desires to do IO for paging purposes.
In that case, the GFP_KERNEL allocation within create_qp causes
a deadlock in tight memory situations.
This fix adds support to create queue pair with GFP_NOIO flag for
connected mode only to cleanly fail the create queue pair in those
situations.
This was previously fixed in qib but needed to get ported to hfi1.
This patch handles that for both hardwares in the new rdmavt common
layer.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
qib needs to reserve only one qpn for non-verbs stuff. Also fixed the for
loop to reserve the end qpn.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Until all queue pair functionality is moved to rdmavt we need to provide
access to the reset function. This is only temporary and will be reverted
back to a static, non exported function in the end.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add table init as well as teardown for handling qpn maps. Drivers can still
provide this functionality by setting the QP_INIT_DRIVER bit.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This adds the post sned and recv function stubs.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adds the stubs for create, modify, destroy and query functions for queue
pairs.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
