The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
net: fsl/fman: address erratum A011043
This addresses a HW erratum on some QorIQ DPAA devices.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
When the issue was present, one could see such errors
during boot:
mdio_bus ffe4e5000: Error while reading PHY0 reg at 3.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fsl,erratum-a011043 to internal MDIO buses.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for erratum A011043: the MDIO_CFG[MDIO_RD_ER]
bit may be falsely set when reading internal PCS registers.
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Primarily bugfixes, mostly around handling index wrap-around correctly.
A couple of doc fixes and adding missing APIs.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAl4pJv4ACgkQDpNsjXcp
gj5OXgf/Q52Am0tLS6iC7XtcojjidnSFzpAqn9OGo7zuTsP+QURsiZAXJpjvUF8y
kGIcD9R/tobEADkyDnj8D64yO+CqT1PlkaYvO5R+nYx/WTtmvr3/O/7Y4/ZTAwcf
tTvj3yXlKbsA+9YJa34t43Ul4EDCOrQTz+oIZUQsiaRNzIdmCCguLg5gOkIhoXt6
wJwp2Fc3YN6McBBpZH2z0GRwdJWPcixtKH0RNhOyGUiWBhkWYFXNvNEdxKJmTXdK
qqkoW9So8IkyyoXdW8ZpQqCCk9tPRv9+7adDFVwl/T8q/RBrHNtcyQqJL3EsScsi
9IqCrKldzRenk0v6lG+mgJEuTvYs8A==
=7cpi
-----END PGP SIGNATURE-----
Merge tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"Primarily bugfixes, mostly around handling index wrap-around
correctly.
A couple of doc fixes and adding missing APIs.
I had an oops live on stage at linux.conf.au this year, and it turned
out to be a bug in xas_find() which I can't prove isn't triggerable in
the current codebase. Then in looking for the bug, I spotted two more
bugs.
The bots have had a few days to chew on this with no problems
reported, and it passes the test-suite (which now has more tests to
make sure these problems don't come back)"
* tag 'xarray-5.5' of git://git.infradead.org/users/willy/linux-dax:
XArray: Add xa_for_each_range
XArray: Fix xas_find returning too many entries
XArray: Fix xa_find_after with multi-index entries
XArray: Fix infinite loop with entry at ULONG_MAX
XArray: Add wrappers for nested spinlocks
XArray: Improve documentation of search marks
XArray: Fix xas_pause at ULONG_MAX
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and calling
trace_set_default_clock()
This v2 version contains:
- A fix to a bug found with the double perf_event linking patch
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXinakBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qhNZAQCi86p9eW3f3w7hM2hZcirC+mQKVZgp
2rO4zIAK5V6G7gEAh6I7VZa50a6AE647ZjryE7ufTRUhmSFMWoG0kcJ7OAk=
=/J9n
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix a function comparison warning for a xen trace event macro
- Fix a double perf_event linking to a trace_uprobe_filter for
multiple events
- Fix suspicious RCU warnings in trace event code for using
list_for_each_entry_rcu() when the "_rcu" portion wasn't needed.
- Fix a bug in the histogram code when using the same variable
- Fix a NULL pointer dereference when tracefs lockdown enabled and
calling trace_set_default_clock()
- A fix to a bug found with the double perf_event linking patch"
* tag 'trace-v5.5-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobe: Fix to make trace_uprobe_filter alignment safe
tracing: Do not set trace clock if tracefs lockdown is in effect
tracing: Fix histogram code when expression has same var as value
tracing: trigger: Replace unneeded RCU-list traversals
tracing/uprobe: Fix double perf_event linking on multiprobe uprobe
tracing: xen: Ordered comparison of function pointers
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl4p1+MTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi4YtCACPHyE8aoDTHZF8UZ9bHKNFVt4C1bRx
ihFB6/PzmIfFw4Cbf+yTW85q3zqJ/6eJIOZF4dlwoFWK+osSk8sYRaOvlEovysbR
sYiAbcOxePj9tSPdrWLYB/5ELtwMTloxBo7mPiJYt127UntWlPGfiz4sdHJBt1zI
IBPOIeACJKGe0+Wtj0mGsXk+WhEB3nFk2DINnLuFc4tG6yXkFNq5/fnXrgVTlUTF
4EwDQgHBUIqKDJarSyIBzud6VVshS7VaMAu8h9kwPScN4sG1y4ucgFzXIc4JfqRN
TnEV48hdRQMVuQtsvuzAMPQvsjMlIXUSTGZzs4XPbEBjgAP8+MP+PJvL
=XVg1
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.5-rc8' of https://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for a potential use-after-free from Jeff, marked for stable"
* tag 'ceph-for-5.5-rc8' of https://github.com/ceph/ceph-client:
ceph: hold extra reference to r_parent over life of request
Prevent the kernel from crashing during resume from hibernation
if free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl4psjQSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxpOcP/1UTGUr+VdGfBBjG5WlgCY0Jrd50Y78b
RoVNDR/NvSVSuIs44AgrnfyQiz2Y8jG6qY1iSAbIXmFl37/4+kGhkNmd6pV/xFUc
TdZZotFwFlRQjmeQxxH0kNXuAY6nJ2RwELWrjXqM8PuNjNKIEpfS+0fSaWexHqIm
MDArxcDHkvZU5SnnRQM+LkT/EmbEheB7tgm7vGGqMLsSKc0gUsBmVCURe/lLAH5o
EUKX4FI2jCy+LlmSdZ3EDjf1cstm3YXLiegTLSq1Jh3mFHXkFTwJMmidiz21qXJh
Hc4r3iG0NZ37J8HXpwuq++KlhvNbhHJz+ZgC1IYls16RNYh5mUzxtMHWdSyyqlrW
+z8gBVUyeJUYos5Kjb/NKSt43gnz7Uhy0UVbQXD66hgajXe71CQZQq/D5CMeTdJL
jWNaeGYnhskz3IW2vnrs9Ucf6RHHWezXk51kVsyJXadiLhTdOv7DKahDKVwC/Hvf
kyN1W0F5PZpF50yYmnhJgqDfxkGBNKpwXxTAGk6X0WQFaWeh/2FkX045UdJzBbHu
fa1taTM/5RfPlbWq0wLPeHHSP4M2I0ndeWXZk88vUwwMfm9Wo+FNBhgs/EZfeuKD
16sVMsX0r7R1bG+hEj+mvNeLWqfgz7MpGludCkV1dHIDkn2esxx6JqaWxR/UnLHb
D3fZM/cKGdpY
=kDFG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Prevent the kernel from crashing during resume from hibernation if
free pages contain leftover data from the restore kernel and
init_on_free is set (Alexander Potapenko)"
* tag 'pm-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: fix crashes with init_on_free=1
In commit 9f79b78ef7 ("Convert filldir[64]() from __put_user() to
unsafe_put_user()") I changed filldir to not do individual __put_user()
accesses, but instead use unsafe_put_user() surrounded by the proper
user_access_begin/end() pair.
That make them enormously faster on modern x86, where the STAC/CLAC
games make individual user accesses fairly heavy-weight.
However, the user_access_begin() range was not really the exact right
one, since filldir() has the unfortunate problem that it needs to not
only fill out the new directory entry, it also needs to fix up the
previous one to contain the proper file offset.
It's unfortunate, but the "d_off" field in "struct dirent" is _not_ the
file offset of the directory entry itself - it's the offset of the next
one. So we end up backfilling the offset in the previous entry as we
walk along.
But since x86 didn't really care about the exact range, and used to be
the only architecture that did anything fancy in user_access_begin() to
begin with, the filldir[64]() changes did something lazy, and even
commented on it:
/*
* Note! This range-checks 'previous' (which may be NULL).
* The real range was checked in getdents
*/
if (!user_access_begin(dirent, sizeof(*dirent)))
goto efault;
and it all worked fine.
But now 32-bit ppc is starting to also implement user_access_begin(),
and the fact that we faked the range to only be the (possibly not even
valid) previous directory entry becomes a problem, because ppc32 will
actually be using the range that is passed in for more than just "check
that it's user space".
This is a complete rewrite of Christophe's original patch.
By saving off the record length of the previous entry instead of a
pointer to it in the filldir data structures, we can simplify the range
check and the writing of the previous entry d_off field. No need for
any conditionals in the user accesses themselves, although we retain the
conditional EINTR checking for the "was this the first directory entry"
signal handling latency logic.
Fixes: 9f79b78ef7 ("Convert filldir[64]() from __put_user() to unsafe_put_user()")
Link: https://lore.kernel.org/lkml/a02d3426f93f7eb04960a4d9140902d278cab0bb.1579697910.git.christophe.leroy@c-s.fr/
Link: https://lore.kernel.org/lkml/408c90c4068b00ea8f1c41cca45b84ec23d4946b.1579783936.git.christophe.leroy@c-s.fr/
Reported-and-tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8a23eb804c ("Make filldir[64]() verify the directory entry
filename is valid") added some minimal validity checks on the directory
entries passed to filldir[64](). But they really were pretty minimal.
This fleshes out at least the name length check: we used to disallow
zero-length names, but really, negative lengths or oevr-long names
aren't ok either. Both could happen if there is some filesystem
corruption going on.
Now, most filesystems tend to use just an "unsigned char" or similar for
the length of a directory entry name, so even with a corrupt filesystem
you should never see anything odd like that. But since we then use the
name length to create the directory entry record length, let's make sure
it actually is half-way sensible.
Note how POSIX states that the size of a path component is limited by
NAME_MAX, but we actually use PATH_MAX for the check here. That's
because while NAME_MAX is generally the correct maximum name length
(it's 255, for the same old "name length is usually just a byte on
disk"), there's nothing in the VFS layer that really cares.
So the real limitation at a VFS layer is the total pathname length you
can pass as a filename: PATH_MAX.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Should work properly with the latest sbios on 5.5 and newer
kernels.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set d0 and d1 pin directions for spi0 and spi1 as per their pinmux.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When submitting v2 of "fou: Support binding FoU socket" (1713cb37bf),
I accidentally sent the wrong version of the patch and one fix was
missing. In the initial version of the patch, as well as the version 2
that I submitted, I incorrectly used ".type" for the two V6-attributes.
The correct is to use ".len".
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 1713cb37bf ("fou: Support binding FoU socket")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0034d395f8 ("powerpc/mm/hash64: Map all the kernel regions in
the same 0xc range") has a bug in the definition of MIN_USER_CONTEXT.
The result is that the context id used for the vmemmap and the lowest
context id handed out to userspace are the same. The context id is
essentially the process identifier as far as the first stage of the
MMU translation is concerned.
This can result in multiple SLB entries with the same VSID (Virtual
Segment ID), accessible to the kernel and some random userspace
process that happens to get the overlapping id, which is not expected
eg:
07 c00c000008000000 40066bdea7000500 1T ESID= c00c00 VSID= 66bdea7 LLP:100
12 0002000008000000 40066bdea7000d80 1T ESID= 200 VSID= 66bdea7 LLP:100
Even though the user process and the kernel use the same VSID, the
permissions in the hash page table prevent the user process from
reading or writing to any kernel mappings.
It can also lead to SLB entries with different base page size
encodings (LLP), eg:
05 c00c000008000000 00006bde0053b500 256M ESID=c00c00000 VSID= 6bde0053b LLP:100
09 0000000008000000 00006bde0053bc80 256M ESID= 0 VSID= 6bde0053b LLP: 0
Such SLB entries can result in machine checks, eg. as seen on a G5:
Oops: Machine check, sig: 7 [#1]
BE PAGE SIZE=64K MU-Hash SMP NR_CPUS=4 NUMA Power Mac
NIP: c00000000026f248 LR: c000000000295e58 CTR: 0000000000000000
REGS: c0000000erfd3d70 TRAP: 0200 Tainted: G M (5.5.0-rcl-gcc-8.2.0-00010-g228b667d8ea1)
MSR: 9000000000109032 <SF,HV,EE,ME,IR,DR,RI> CR: 24282048 XER: 00000000
DAR: c00c000000612c80 DSISR: 00000400 IRQMASK: 0
...
NIP [c00000000026f248] .kmem_cache_free+0x58/0x140
LR [c088000008295e58] .putname 8x88/0xa
Call Trace:
.putname+0xB8/0xa
.filename_lookup.part.76+0xbe/0x160
.do_faccessat+0xe0/0x380
system_call+0x5c/ex68
This happens with 256MB segments and 64K pages, as the duplicate VSID
is hit with the first vmemmap segment and the first user segment, and
older 32-bit userspace maps things in the first user segment.
On other CPUs a machine check is not seen. Instead the userspace
process can get stuck continuously faulting, with the fault never
properly serviced, due to the kernel not understanding that there is
already a HPTE for the address but with inaccessible permissions.
On machines with 1T segments we've not seen the bug hit other than by
deliberately exercising it. That seems to be just a matter of luck
though, due to the typical layout of the user virtual address space
and the ranges of vmemmap that are typically populated.
To fix it we add 2 to MIN_USER_CONTEXT. This ensures the lowest
context given to userspace doesn't overlap with the VMEMMAP context,
or with the context for INVALID_REGION_ID.
Fixes: 0034d395f8 ("powerpc/mm/hash64: Map all the kernel regions in the same 0xc range")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: Christian Marillat <marillat@debian.org>
Reported-by: Romain Dolbeau <romain@dolbeau.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Account for INVALID_REGION_ID, mostly rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200123102547.11623-1-mpe@ellerman.id.au
Hayes Wang says:
====================
r8152: serial fixes
v3:
1. Fix the typos for patch #5 and #6.
2. Modify the commit message of patch #9.
v2:
For patch #2, move declaring the variable "ocp_data".
v1:
These patches are used to fix some issues for RTL8153.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The optee driver uses specific page table types to verify if a memory
region is normal. These types are not defined in nommu systems. Trying
to compile the driver in these systems results in a build error:
linux/drivers/tee/optee/call.c: In function ‘is_normal_memory’:
linux/drivers/tee/optee/call.c:533:26: error: ‘L_PTE_MT_MASK’ undeclared
(first use in this function); did you mean ‘PREEMPT_MASK’?
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~
PREEMPT_MASK
linux/drivers/tee/optee/call.c:533:26: note: each undeclared identifier is
reported only once for each function it appears in
linux/drivers/tee/optee/call.c:533:44: error: ‘L_PTE_MT_WRITEALLOC’ undeclared
(first use in this function)
return (pgprot_val(p) & L_PTE_MT_MASK) == L_PTE_MT_WRITEALLOC;
^~~~~~~~~~~~~~~~~~~
Make the optee driver depend on MMU to fix the compilation issue.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[jw: update commit title]
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
phylink and phylib are interconnected. It makes sense for phylib and
phy driver patches to be also reviewed by the phylink maintainer.
So add Russell King as a designed reviewer of phylib.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-panfrost: Fix mapping of globally visible BO's (Boris)
Cc: Wayne Lin <Wayne.Lin@amd.com>
CC: Boris Brezillon <boris.brezillon@collabora.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl4ov40ACgkQcywAJXLc
r3lceQgA0Oag+iEH5BPC2fkxtmv2VY0WA3fbyC3HHnLURdAODDFemCddqec9j4JQ
56A39V8jYZXcbX2d66Go9QHdCGjVH0a303+0H0OkV0ciY8XTjuRXkQHTnZ2SO3o8
7dQaLelHpbICLc5P4IQzgg5e94gFR3vRcs7lVMi5TlKRv5BN3B2kKFB4muSW28tM
aXzRl4fUaR2n3MO9ItiqgBh+4H3aqlbyRXwQ6flXXI7Cpme23HLjwuDmug3Vznau
oJUBVsyOmb2HBY+jtoCrsmiM1l7APZFZMguDd9Tmk4H+ZizEC5Zrdx4bkqlTlPWR
KwLP9xYp1HWpAuw8h4jwafy/px3cUA==
=mUse
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2020-01-22-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
-mst: Fix SST branch device handling (Wayne)
-panfrost: Fix mapping of globally visible BO's (Boris)
Cc: Wayne Lin <Wayne.Lin@amd.com>
CC: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122213725.GA22099@art_vandelay
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAl4orFoACgkQMOfwapXb+vIa4wCgg80d89IVa0KcC4JXKZ9q1gBw
ju4AnAn/JE9zDX9bbc1aRHUGdK/ZCa7Z
=uETI
-----END PGP SIGNATURE-----
Merge tag 'leds-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED fixes from Pavel Machek:
"Jacek's fix for an uninitialized gpio label is why I'm requesting this
pull; it fixes regression in debugging output in sysfs. Others are
just bugfixes that should be safe.
Everything has been in -next for while"
* tag 'leds-5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lm3532: add pointer to documentation and fix typo
leds: rb532: cleanup whitespace
ledtrig-pattern: fix email address quoting in MODULE_AUTHOR()
led: max77650: add of_match table
leds-as3645a: Drop fwnode reference on ignored node
leds: gpio: Fix uninitialized gpio label for fwnode based probe
In hwmon core, do not use the hwmon parent device for device managed
memory allocations, since parent device lifetime may not match hwmon
device lifetime.
Fix discrepancy between read and write values in adt7475 driver.
Fix alarms and voltage limits in nct7802 driver.
-----BEGIN PGP SIGNATURE-----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=achg
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- In hwmon core, do not use the hwmon parent device for device managed
memory allocations, since parent device lifetime may not match hwmon
device lifetime.
- Fix discrepancy between read and write values in adt7475 driver.
- Fix alarms and voltage limits in nct7802 driver.
* tag 'hwmon-for-v5.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (core) Do not use device managed functions for memory allocations
hwmon: (adt7475) Make volt2reg return same reg as reg2volt input
hwmon: (nct7802) Fix non-working alarm on voltages
hwmon: (nct7802) Fix voltage limits to wrong registers
in the same manner as commit d0f4185160 ("net, ip_tunnel: fix
namespaces move"), fix namespace moving as it was broken since commit
8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for
ipv6 this time; there is no reason to keep it for ip6_tunnel.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel")
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0d4a6608f6.
Williem reported that after commit 0d4a6608f6 ("udp: do rmem bulk
free even if the rx sk queue is empty") the memory allocated by
an almost idle system with many UDP sockets can grow a lot.
For stable kernel keep the solution as simple as possible and revert
the offending commit.
Reported-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Fixes: 0d4a6608f6 ("udp: do rmem bulk free even if the rx sk queue is empty")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
