The calculation of the left volume looks suspect, the value of
0x1f - ((val << 8) & 0x1f) is always 0x1f. The debug prior to the
assignment of value[1] prints the left volume setting using the
calculation 0x1f - (val >> 8) & 0x1f which looks correct to me.
Fix the left volume by using the correct expression as used in
the debug.
Detected by CoverityScan, CID#146140 ("Wrong operator used")
Fixes: 850d24a5a8 ("[media] em28xx-alsa: add mixer support for AC97 volume controls")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While committing a change on em28xx, I got a warning of a
typo there. So, fix it on em28xx and on two other media drivers
with the same typo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While testing support for Terratec H6 rev. 2, it was noticed
that reading from eeprom there causes a timeout error.
Apparently, this is due to the need of properly setting GPIOs.
In any case, the driver doesn't really require eeprom reading
to succeed, as this is currently used only for debug.
So, Ignore such errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- avoid duplicate debugging messages in em28xx_read_reg_req_len()
- do not describe successful usb transfers in em28xx_read_reg_len()
as "failed"
- report errors in em28xx_write_regs_req(), too
- print the usb error numbers, too
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adding support for SRGGB8 is as simple as adding a new entry at
struct em28xx_fmt.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CbYCrY has been identified by looking into the tvp5150 driver and the
saa7115 datasheet.
YUV formats have been verified with em2765 + ov2640 (VAD Laplace webcam).
RGB8 formats have been verified with em2710/em2820 + mt9v011 (Silvercrest
webcam 1.3mpix).
I also did some cross-checking with these two camera devices and 0x08-0x0b
are at least 16 bits per pixel formats on em2710/em2820, too, and
0x0c-0x0f are at least 8 bits per pixel formats on em2765, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With an unknown sensor, norm_maxw() and norm_maxh() return 0 as max.
height and width values, which causes a devide by zero in size_to_scale().
Of course we could use speculative default values for unknown sensors,
but the chance that the device works at this resolution without any
driver/setup is very low and therefore not worth the efforts.
Instead, just don't treat the device as camera.
A message will then be printed to the log that the device isn't supported.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With MEDIA_SUBDRV_AUTOSELECT enabled in the kernel config, the em28xx
driver currently does't select some used subdrivers.
Fix this by adding the missing auto-selections to the Kconfig file.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2 dummy clock has been added with commit fc5d0f8a88
("V4L2: em28xx: register a V4L2 clock source") to be able to use the ov2640
soc_camera driver.
Since commit 46796cfcd3 ("ov2640: use standard clk and enable it") it is
no longer required.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use i2c_smbus_read_word_data() instead of i2c_master_send() and
i2c_master_recv() for reading the ID of Micorn sensors.
i2c_smbus_read_word_data() assumes that byes are in little-endian,
so, it uses:
data->word = msgbuf1[0] | (msgbuf1[1] << 8);
However, Micron datasheet describes the ID as if they were read
in big-endian. So, we need to change the byte order in order to
match the ID number as described on their datasheets.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new usbid eb1a:5051 for the Ion Video 2 PC MKII, Startech svid2usb23
and Raygo R12-41373.
Signed-off-by: Alexandre-Xavier Labonté-Lamoureux <alexandrexavier@live.ca>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The em28xx driver still used the soc_camera.h header for the ov2640
driver. Since this driver no longer uses soc_camera, that include can
be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's no longer necessary to keep the i2c_client in the device struct
unmodified until a sensor is found, so reduce stack usage in
em28xx_probe_sensor_micron() and em28xx_probe_sensor_omnivision() by using
a pointer to the client instead of a local copy.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tveeprom_hauppauge_analog() used to need the I2C adapter in
order to print debug messages. As it now uses pr_foo() facilities
since commit 6037b3ca28 ("[media] tveeprom: print log messages
using pr_foo()"), the first argument of the function is not
needed anymore.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop the FSF's postal address from the source code files that typically
contain mostly the license text. Of the 628 removed instances, 578 are
outdated.
The patch has been created with the following command without manual edits:
git grep -l "675 Mass Ave\|59 Temple Place\|51 Franklin St" -- \
drivers/media/ include/media|while read i; do i=$i perl -e '
open(F,"< $ENV{i}");
$a=join("", <F>);
$a =~ s/[ \t]*\*\n.*You should.*\n.*along with.*\n.*(\n.*USA.*$)?\n//m
&& $a =~ s/(^.*)Or, (point your browser to) /$1To obtain the license, $2\n$1/m;
close(F);
open(F, "> $ENV{i}");
print F $a;
close(F);'; done
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Now that we're storing usb_interface at em28xx struct,
there's no good reason to keep storing usb_device, as we can
get it from usb_interface. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The usb_device->dev is not the right device for dev_foo() calls.
Instead, it should use usb_interface->dev.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In randconfig builds that select VIDEO_EM28XX_V4L2 and
MEDIA_SUBDRV_AUTOSELECT, but not MEDIA_CAMERA_SUPPORT, we get
a Kconfig warning:
warning: (VIDEO_EM28XX_V4L2) selects VIDEO_MT9V011 which has unmet direct dependencies (MEDIA_SUPPORT && I2C && VIDEO_V4L2 && MEDIA_CAMERA_SUPPORT)
This avoids the warning by making that 'select' conditional on
MEDIA_CAMERA_SUPPORT. Alternatively we could mark EM28XX as
'depends on MEDIA_CAMERA_SUPPORT', but it does not seem to
have any real dependency on that itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are still several places with printk's called directly.
Convert them to pr_foo() macros, except for the debug printk's,
as those are enabled via modprobe vars.
While here, realign the pr_foo() arguments to match the
recommended CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has a lot of printk continuation lines for
debugging purposes. Since commit 563873318d
("Merge branch 'printk-cleanups"), this won't work as expected
anymore. So, let's add KERN_CONT to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols checkpatch warnings, several strings
were broken into multiple lines. This is not considered
a good practice anymore, as it makes harder to grep for
strings at the source code. So, join those continuation
lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These i2c_algorithm structures are only stored in the alg field of an
i2c_adapter structure, which is declared as const. This declare the
structures as const as well.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.alg = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for snd_pcm_ops structures that are only stored in the ops field of a
snd_soc_platform_driver structure or passed as the third argument to
snd_pcm_set_ops. The corresponding field or parameter is declared const,
so snd_pcm_ops structures that have this property can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_pcm_ops i@p = { ... };
@ok1@
identifier r.i;
struct snd_soc_platform_driver e;
position p;
@@
e.ops = &i@p;
@ok2@
identifier r.i;
expression e1, e2;
position p;
@@
snd_pcm_set_ops(e1, e2, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct snd_pcm_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_pcm_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d3 ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The code is checking for negative returns but it should be checking for
zero.
Fixes: aab3125c43 ('[media] em28xx: add support for registering multiple i2c buses')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
EMP202 chip inside Terratec Grabby (hw rev 2) seems to require some time
before accessing reliably its registers. Otherwise it returns some values
previously put on the I2C bus.
To account for that period, we delay card setup until we have a proof that
accessing AC97 registers is reliable. We get this proof by polling
AC97_RESET until the expected value is read. We also check that unrelated
registers don't return the same value. This second check handles the case
where the expected value is constantly returned no matter which register
is accessed.
Signed-off-by: Matthieu Rogez <matthieu.rogez@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Terratec Grabby (hw rev 2) Record led is connected to GPIO 3
and its logic is inverted: (PIO3 = 0: on, PIO3 = 1: off).
Signed-off-by: Matthieu Rogez <matthieu.rogez@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cleanup that changed the em28xx driver to use v4l2_mc_create_media_graph
instead of its own implementation causes a build error when CONFIG_MEDIA_CONTROLLER
is disabled:
drivers/media/usb/em28xx/em28xx-video.c: In function 'em28xx_v4l2_init':
drivers/media/usb/em28xx/em28xx-video.c:2717:38: error: 'struct em28xx' has no member named 'media_dev'
This puts the new code inside the same #ifdef that controls the presence
of the 'media_dev' member, and that the old code was in.
Fixes: de39078779 ("[media] em2xx: use v4l2_mc_create_media_graph()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, media_device_pci_init and media_device_usb_init does
media_device allocation internaly. That preents its usage when
the media_device struct is embedded on some other structure.
Move memory allocation outside it, to make it more generic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
