This code has been kept around in anticipation of adding support for
40MHz channels, but subsequent patches to better integrate with mac80211
regulatory support will render it completely broken. Therefore we should
go ahead and remove it.
Keep these changes separate from other cleanup patches in order to make
it easier to resurrect 40MHz channel support at some point in the
future.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations brcmsmac is choosing a channel internally. This makes
it difficult at times to know what channel to use for enforcing
regulatory constraints, so instead always use the channel from the
mac80211 configuration.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is unnecessary, and in fact it's never executed because the
interface is never up when brcms_c_channels_commit() is called. Removing
it helps simplify the implementation of proper regulatory support.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for WEP open/shared encryption in AP mode.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To enhance readability, create a separate function for parsing
WPA/WPA2 related parameters from cfg80211_ap_settings.
There is no functional change in this patch.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse HT IE from cfg80211 and set HT capabilities accordingly
to FW. If HT IE is missing, 11n would be disabled in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds functionality to set channel info received from
cfg80211_ap_settings in start_ap handler.
Since set_channel cfg80211 handler has been removed and we need
not explicitely call mwifiex_uap_set_channel(); hence this
function definition is also removed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust ah->config.ofdm_trig_{high,low} when setting noise immunity values
to simplify threshold checks in ath9k_hw_ani_monitor
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit af1e8a6f "ath9k: reset noiseimmunity level to default" was supposed
to ensure that the default noise immunity level is above the INI
values, however it prevents setting lower noise immunity values altogether.
Fix this by moving the checks to the right function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was found to be buggy on a variety of chipsets from AR913x to AR928x.
The new version (which was introduced along with AR93xx support) is more
reliable in preventing connectivity dropouts and also fixes MIB interrupt
storm issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon RSSI is only meaningful in station mode - in ad-hoc mode it
fluctuates, depending on which peer last sent a beacon, and in other
modes it is not set at all.
Fix places in ANI where the beacon RSSI is used to limit their use
to station mode only.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code using this had already triggered smatch complaints, so remove it before
it gets fixed the wrong way.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
was unifying some code related to overriding OFDM weak signal detection,
but seems to have gotten some of the original intent wrong, probably
because of a misnamed variable.
The beacon RSSI is only valid in station mode, and the main reason to check
it in ath9k_hw_set_ofdm_nil is to make sure that OFDM weak signal detection
stays enabled if the RSSI is low, even when the OFDM noise immunity entry
is supposed to disable it.
The above commit removed the mode checks and changed the code so that
OFDM weak signal detection would only be changed if the rssi is high, which
is wrong for everything but client mode.
This patch restores the old behavior in a simplified form.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I don't know why somebody decided to keep a cached copy of beacon rssi in a
variable called 'noiseFloor', but the caching is unnecessary and the variable
name is confusing, so let's just get rid of it entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The checkdied functionality provides useful information for analyzing
firmware crashes. By exposing this information to a debugfs file users
can easily provide its content in bug reports. The functionality is
available only when CONFIG_BRCMDBG is selected.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch support the new chipset rt3290 wifi implementation in rt2x00.
It initailize the related mac, bbp and rf register in startup phase.
And this patch modify the efuse read/write method for the different efuse data offset of rt3290.
Signed-off-by: Woody Hung <Woody.Hung@mediatek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the eeprom parsing code overrides the sku
field directly with 11n_disable parameters, there's
no longer a need to keep a copy of this field.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The effect of using a short single-channel scan
to reset the radio is that scanning a channel
that isn't in use needs to re-tune the radio.
This means that the dwell time is irrelevant,
so use a shorter time.
While at it, clean up the code for this a bit.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 26a7ca9a71 ("iwlwifi: refactor EEPROM reading/parsing")
broke the 11n_disable module parameter's BIT(0) to disable all HT
operation (using the other bits to disable aggregation only was
unaffected). Restore this by overriding the SKU when parsing the
EEPROM if the module parameter is set.
Reported-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the device is doing an internal radio reset
scan, ROC can be rejected to the supplicant with
busy status which confuses it.
One option would be to queue the ROC and handle
it later, but since the radio reset scan is very
quick we can just wait for it to finish instead.
Also add a warning since we shouldn't run into
the case of having a scan active when requesting
a ROC in any other case since mac80211 will not
scan while ROC or ROC while scanning.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This feature needs to be disabled for all NICs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This variable was accessed without taking the lock.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really not needed, we already have a lock inside
the accesses to the prph.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not needed since notif_wait_lock is never accessed
from IRQ.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is required by the op_mode API.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few op_mode of the op_mode API functions have requirements
on the running context of the caller. Document that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We introduced a lock here in ff1ffb850b ("iwlwifi: fix dynamic
loading"). But we missed an error path which needs an unlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug where no capabilites are parsed when the number
of firmware capability bits translate into fewer bytes than the host has
knowledge of. Instead just process number of capability bytes as
reported by the firmware.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
remove MCI_STATE_BT and use bt_state instead.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As p_data is unuse, lets remove it from ar9003_mci_state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a MCI util function to send wlan channel info to BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
