It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The following commits break cpuidle on SH-Mobile ARM:
46bcfad cpuidle: Single/Global registration of idle states
e978aa7 cpuidle: Move dev->last_residency update to driver enter routine; remove dev->last_state
This patch remedies these issues by up-porting the SH-Mobile
code to fit with the above introduced framework changes.
It is worth noting that the new code becomes significantly cleaner,
so these framework changes are very welcome. At the same time this
breakage could probably have been avoided by grepping for "last_state"
and "cpuidle_register_driver".
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves PORT_xx helper macro to sh_pfc.h,
and it expects CPU_ALL_PORT() macro for each CPU
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch move PORT_DATA_xx helper macro to sh_pfc.h.
and pfc-sh7372.c used it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
it is not necessary to have sh7372_xxxx index on static variable
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MMC data pin pull-up option for pfc-sh73a0.c,
and select it on ag5evm board.
The MMC read/write will be error without this patch.
Cc: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in entries for both Goda and Morimoto-san who have previously
used different conventions.
Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all of the named string association with clocks has been
migrated to clkdev lookups there's no meaningful named topology that can
be constructed for a debugfs tree view. Get rid of the left over bits,
and shrink struct clk a bit in the process.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up and fix pwr_nids for 92HD71 / 73 / 83 family codecs; remove
pwr_mapping which was incorrect.
The original pwr_nids support of 92HD83xxx was incorrect and never
actually worked before. Now we should have things working correctly
without having to hack by DID anymore.
It is also not necessary to explicitly turn on all the pins near the
beginning of patch_stac92hd83xxx() now, the pins will go though
initialization properly.
Tested on 92HD66 / 71 / 73 / 75 / 83 / 89 / 91 demo boards.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The runtime PM platform support stub in use by ARM-based SH/R-Mobile
platforms contains nothing that's specifically ARM-related and instead of
wholly generic to anything using the clock framework.
The recent runtime PM changes interact rather badly with the lazy
disabling of clocks late in the boot process through the clock framework,
leading to situations where the runtime suspend/resume paths are entered
without a clock being actively driven due to having been lazily gated
off.
In order to correct this we can trivially tie in the aforementioned stub
as a general fallback for all SH platforms that don't presently have
their own runtime PM implementations (the corner case being SH-based
SH-Mobile platforms, which have their own stub through the hwblk API --
which in turn has bitrotted and will be subsequently adapted to use the
same stub as everyone else), regardless of whether the platforms choose
to define power domains of their own or not.
This fixes up regressions for clock framework users who also build in
runtime PM support without any specific power domains of their own, which
was previously causing the serial console to be lost when warring with
lazy clock disabling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can not do flushable reservation for the relocation when we create snapshot,
because it may make the transaction commit task and the flush task wait for
each other and the deadlock happens.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
People have been running into a warning when loading space cache because the
page is already mapped when trying to read in a bitmap. The way we read in
entries and pages is kind of convoluted, so fix it so that io_ctl_read_entry
maps the entries if it needs to, and if it hits the end of the page it simply
unmaps the page. That way we can unconditionally unmap the io_ctl before
reading in the bitmap and we should stop hitting these warnings. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If the root node of a fs/file tree is in the block group that is
being relocated, but the others are not in the other block groups.
when we create a snapshot for this tree between the relocation tree
creation ends and ->create_reloc_tree is set to 0, Btrfs will create
some backref nodes that are the lowest nodes of the backrefs cache.
But we forget to add them into ->leaves list of the backref cache
and deal with them, and at last, they will triggered BUG_ON().
kernel BUG at fs/btrfs/relocation.c:239!
This patch fixes it by adding them into ->leaves list of backref cache.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_block_rsv_add{, _noflush}() have similar code, so abstract that code.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we did stress test for the space relocation, the deadlock happened.
By debugging, We found it was caused by the carelessness that we forgot
to unlock the read lock of the extent buffers in btrfs_orphan_cleanup()
before we end the transaction handle, so the transaction commit task waited
the task, which called btrfs_orphan_cleanup(), to unlock the extent buffer,
but that task waited the commit task to end the transaction commit, and
the deadlock happened. Fix it.
Signed-ff-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
I-node cache forgets to reserve the space when writing out it. And when
we do some stress test, such as synctest, it will trigger WARN_ON() in
use_block_rsv().
WARNING: at fs/btrfs/extent-tree.c:5718 btrfs_alloc_free_block+0xbf/0x281 [btrfs]()
...
Call Trace:
[<ffffffff8104df86>] warn_slowpath_common+0x80/0x98
[<ffffffff8104dfb3>] warn_slowpath_null+0x15/0x17
[<ffffffffa0369c60>] btrfs_alloc_free_block+0xbf/0x281 [btrfs]
[<ffffffff810cbcb8>] ? __set_page_dirty_nobuffers+0xfe/0x108
[<ffffffffa035c040>] __btrfs_cow_block+0x118/0x3b5 [btrfs]
[<ffffffffa035c7ba>] btrfs_cow_block+0x103/0x14e [btrfs]
[<ffffffffa035e4c4>] btrfs_search_slot+0x249/0x6a4 [btrfs]
[<ffffffffa036d086>] btrfs_lookup_inode+0x2a/0x8a [btrfs]
[<ffffffffa03788b7>] btrfs_update_inode+0xaa/0x141 [btrfs]
[<ffffffffa036d7ec>] btrfs_save_ino_cache+0xea/0x202 [btrfs]
[<ffffffffa03a761e>] ? btrfs_update_reloc_root+0x17e/0x197 [btrfs]
[<ffffffffa0373867>] commit_fs_roots+0xaa/0x158 [btrfs]
[<ffffffffa03746a6>] btrfs_commit_transaction+0x405/0x731 [btrfs]
[<ffffffff810690df>] ? wake_up_bit+0x25/0x25
[<ffffffffa039d652>] ? btrfs_log_dentry_safe+0x43/0x51 [btrfs]
[<ffffffffa0381c5f>] btrfs_sync_file+0x16a/0x198 [btrfs]
[<ffffffff81122806>] ? mntput+0x21/0x23
[<ffffffff8112d150>] vfs_fsync_range+0x18/0x21
[<ffffffff8112d170>] vfs_fsync+0x17/0x19
[<ffffffff8112d316>] do_fsync+0x29/0x3e
[<ffffffff8112d348>] sys_fsync+0xb/0xf
[<ffffffff81468352>] system_call_fastpath+0x16/0x1b
Sometimes it causes BUG_ON() in the reservation code of the delayed inode
is triggered.
So we must reserve enough space for inode cache.
Note: If we can not reserve the enough space for inode cache, we will
give up writing out it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
btrfs_previous_item() just search the b+ tree, do not COW the nodes or leaves,
if we modify the result of it, the meta-data will be broken. fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef sent along an incremental to the inode reservation
code to make sure we try and fall back to directly updating
the inode item if things go horribly wrong.
This reworks that patch slightly, adding a fallback function
that will always try to update the inode item directly without
going through the delayed_inode code.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The report functions use NLA_PUT so we need to ensure that NET
is enabled.
Reported-by: Luis Henriques <henrix@camandro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some incomming connections needs to increase the security level by
requesting encryption for example (HID keyboard case). This change allows
the userspace to change it through setsockopt with defer_setup enabled.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
rename to l2cap_chan_check_security() to make it consistent with other
l2cap_exported functions. This function will be exported in a later
commit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Drivers should not use NO_IRQ; moreover, some architectures don't
have it nowadays. '0' is the 'no irq' case.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Without this patch we get the following error:
arch/arm/mach-omap2/clkt_dpll.c: In function '_dpll_test_fint':
arch/arm/mach-omap2/clkt_dpll.c:98: error: 'struct dpll_data' has no member named 'flags'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since disconnecting may fail the status needs to be communicated to user
space. This also updates the implementation to match the latest mgmt API
specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since the command can fail we need to have a proper response with the
remote address and a failure status for it. This also updates it to
conform to the latest mgmt API spec.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The hci_conn callbacks are called with the hci_dev lock already held so
no locking should be attempted in them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
It's necessary to know the distinction between public and random LE
addresses so the mgmt interface also needs to distinguish between them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
pNFS-specific code belongs in the pnfs layer. It should not be
hijacking generic NFS read or write code paths.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Otherwise we will leak xprt structure and struct net reference.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For some frequencies, the clocks_calc_mult_shift() function will
unfortunately select mult values very close to 0xffffffff. This
has the potential to overflow when NTP adjusts the clock, adding
to the mult value.
This patch adds a clocksource.maxadj value, which provides
an approximation of an 11% adjustment(NTP limits adjustments to
500ppm and the tick adjustment is limited to 10%), which could
be made to the clocksource.mult value. This is then used to both
check that the current mult value won't overflow/underflow, as
well as warning us if the timekeeping_adjust() code pushes over
that 11% boundary.
v2: Fix max_adjustment calculation, and improve WARN_ONCE
messages.
v3: Don't warn before maxadj has actually been set
CC: Yong Zhang <yong.zhang0@gmail.com>
CC: David Daney <ddaney.cavm@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Chen Jie <chenj@lemote.com>
CC: zhangfx <zhangfx@lemote.com>
CC: stable@kernel.org
Reported-by: Chen Jie <chenj@lemote.com>
Reported-by: zhangfx <zhangfx@lemote.com>
Tested-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Use kmemdup rather than duplicating its implementation
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I am running SMP Linux 2.6.37-rc1 on BMIPS5000 (single core dual thread)
and observe some abnormalities when doing system suspend/resume which I
narrowed down to cpu hotplugging. The suspend brings the second thread
processor down and then restarts it, after which I see memory corruption
in userspace. I started digging and found out that problem occurs because
while doing execve() the child process is getting the same ASID as the
parent, which obviously corrupts parent's address space.
Further digging showed that activate_mm() calls get_new_mmu_context() to
get a new ASID, but at this time ASID field in entryHi is 1, and
asid_cache(cpu) is 0x100 (it was just reset to ASID_FIRST_VERSION when
the secondary TP was booting).
So, get_new_mmu_context() increments the asid_cache(cpu) value to
0x101, and thus puts 0x01 into entryHi. The result - ASID field does
not get changed as it was supposed to.
My solution is very simple - do not reset asid_cache(cpu) on TP warm
restart.
Patchwork: https://patchwork.linux-mips.org/patch/1797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The parse_mtd_partitions() and mtd_device_register() functions were
combined into mtd_device_parse_register(). So call that instead.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC [M] arch/mips/kernel/cpufreq/loongson2_clock.o
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:168:15: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:169:20: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:170:16: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
