This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The sharpsl code selects the max1111 spi driver, so it must also
ensure that SPI itself is enabled. The platform does not work
without max1111.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The two platforms are part of the palm27x family and use the same
code. Select the palm27x symbol to make sure they can be built
standalone.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The raumfeld platform code calls power_supply_set_battery_charged
which is part of the power supply layer, so that always has
to be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
We cannot support ARMv5 and ARMv7 based boards in a single kernel,
so introduce a new option in mach-pxa to select between the two.
The PJ4 (ARMv7) based boards are now only visible when
CONFIG_ARCH_PXA_V7 is set, the other boards are only visible
when it's not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa specific cpufreq code is based on the cpu_freq_table
module, so we have to select that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
saarb uses pxa3xx_map_io and pxa3xx_handle_irq, which are part
of the pxa3xx code. This makes sure the necessary header and
implementation is used when building the board file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
There are two variants of the palmtreo machine, the 680 and the
centro, and Kconfig allows selecting one or both of them.
This changes the board file so that it's actually possible
to build all configurations that are allowed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The pxa3xx_u2d_start_hc/pxa3xx_u2d_stop_hc symbols are used by the
ohci-pxa27x driver, which can be a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When support for zylonite is disabled, the zylonite_pxa300_init
and zylonite_pxa320_init functions are not there, but the declaration
is still kept around if any other boards for the same soc are
enabled. This changes the declaration to be conditional on the
same symbol as the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently the tuner is constantly powered causing these effects.
1. Remembering last tune channel causing corruptions of changing channel.
2. Causing corruption on other frontend.
3. Higher current in standby of demodulator with clock running.
Power sequence now follows;
Power Up
Tuner on -> Frontend suspend off -> Tuner clk on
Power Down
Frontend suspend on -> Tuner clk off -> Tuner off
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tvp5150 video decoder has two operation modes to configure the video
standard used.
If auto-switch mode is enable, the device can sense the signal and detect which
video standard the device is operating. Also the device can be forced to use a
user defined video standard.
Each operation mode uses a different register and the bitmask values to
represent each standard is different.
So we add video standard constants for both autoswitch and no-autoswitch mode.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both mt9t001.c and mt9p031.c have two identical issues, those
being that they will need module.h inclusion for the upcoming
cleanup going on there, and that their dependencies don't limit
selection of configs that will fail to compile as follows:
The related config options are CONFIG_MEDIA_CONTROLLER and
CONFIG_VIDEO_V4L2_SUBDEV_API. Looking at the code, it appears
that the driver was never intended to work without these enabled,
so add a dependency on CONFIG_VIDEO_V4L2_SUBDEV_API, which in
turn already has a dependency on CONFIG_MEDIA_CONTROLLER.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As msp3400 allows standards detection, add support for it. That
efectivelly means that devices with msp3400 can now implement
VIDIOC_QUERYSTD, and it will provide very good detection for
the standard, specially if combined with a video decoder detection.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorganize the standards macro and add a few more, that will be
used on msp3400 in order to allow it to detect the audio standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using V4L2_STD_ALL when no standard is detected,
trust that the maximum allowed standards are already filled by
the V4L2 core. It is better this way, as the bridge and/or the audio
decoder may have some extra restrictions to some video standards.
This also allow other devices like audio and tuners to contribute to
standards detection, when they support such feature.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with the V4L2 API spec:
"When detection is not possible or fails, the set must contain
all standards supported by the current video input or output."
The V4L2 core has the mask with all supported standards already. So,
apply it. Driver and subdevs can then just remove standards from the
mask, as they're able of detecting audio, video and frames frequency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several bugs at saa7115 standards detection:
After the fix, the driver is returning the proper standards,
as tested with 3 different broadcast sources:
On an invalid channel (without any TV signal):
[ 4394.931630] saa7115 15-0021: Status byte 2 (0x1f)=0xe0
[ 4394.931635] saa7115 15-0021: detected std mask = 00ffffff
With a PAL/M signal:
[ 4410.836855] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4410.837727] saa7115 15-0021: Status byte 1 (0x1e)=0x82
[ 4410.837731] saa7115 15-0021: detected std mask = 00000900
With a NTSC/M signal:
[ 4422.383893] saa7115 15-0021: Status byte 2 (0x1f)=0xb1
[ 4422.384768] saa7115 15-0021: Status byte 1 (0x1e)=0x81
[ 4422.384772] saa7115 15-0021: detected std mask = 0000b000
Tests were done with a WinTV PVR USB2 Model 29xx card.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ARMv6 cores do not implement the DBGOSLAR register, so we don't need to
try and clear it on boot. Furthermore, the VCR is zeroed out of reset,
so we don't need to zero it explicitly when a CPU comes online.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Rx hashing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves the Tx hang check into the ring flags.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up several issues with VLANs on igb after the recent
changes that were meant to leave the VLANs enabled/disable via the
netdev->features flags.
Specifically the Rx VLAN settings were being dropped after reset due to the
fact that they were not being restored correctly. In addition I removed
the IRQ disable/enable since those were in place to protect the setting of
vlgrp.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of doing a byte swap on the staterr bits in the Rx descriptor we can
save ourselves a bit of space and some CPU time by instead just testing for
the various bits out of the Rx descriptor directly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the netdev now has its' own checksum flag to indicate if Rx checksum
is enabled we might as well use that instead of using the ring flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to cleanup some of the IVAR register configuration.
igb_assign_vector had become pretty large with multiple copies of the same
general code for setting the IVAR. This change consolidates most of that
code by adding the igb_write_ivar function which allows us just to compute
the index and offset and then use that information to setup the IVAR.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves information related to interrupt throttle rate
configuration into a separate q_vector sub-structure called a work
container. A similar change has already been made for ixgbe and this work
is based off of that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves all of the ring flags into a single value. The advantage
to this is that there is one central area for all of these flags and they
can all make use of the set/test bit operations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a number of places where we have values that are stored as u16
but are being converted to int unnecessarily. In order to avoid that we
should convert all variables that deal with the next_to_clean, next_to_use,
and count to u16 values.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to update the ring and vector allocations so that they
are per node instead of allocating everything on the node that
ifconfig/modprobe is called on. By doing this we can cut down
significantly on cross node traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of storing most of the data for the TX hot path in the stack until
we are ready to write the descriptor we can save ourselves some time and
effort by pushing the SKB, tx_flags, gso_size, bytecount, and protocol into
the first igb_tx_buffer since that is where we will end up putting it
anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds missing #includes, makes the driver selectable on
non-PPC OF-enabled platforms and fixes property value accesses to
be correct in Little Endian system.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove a lot of ' ' (double spaces) as well as ensuring use of tabs vs.
spaces is appropriate and consistent.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This pushes timing and other values into preinitialized read-only data
sections rather than being inlined into the code. None of these
functions are called more than a handful of times, so reducing code size
makes sense.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This ports the timing values over from the old IDE driver into the new
PATA-based one. The comment was lying when it stated the old driver was
not MWDMA capable.
Boot tested on actual hardware using 'libata.force=mwdma2'.
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This mirrors a very old commit (3160d5416f, "sis5513: add
->udma_filter method for chipset_family >= ATA_133") to the old sis5513
IDE driver that prevents certain setups from working.
UDMA6 (ATA/133) is not supported on some chipsets and we need to ensure
this mode is not chosen even if a connected drive supports it. Port this
old patch forward to the new PATA driver to ensure UDMA5 is the highest
mode used if that is what is supported.
Kernel bugzilla #41582.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is similar to the existing sis_old_port_base() method. We do this
same calculation and logic in multiple places (with one more to come in
a future patch), so extracting it into a method makes sense.
Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On imx53 AHCI, soft reset fails with IPMS set when PMP
is enabled but SATA HDD/ODD is connected to SATA port,
do soft reset again to port 0.
So the 'ahci_pmp_retry_srst_ops' is required when imx53
ahci is present.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reduce data by using const.
$ size drivers/ata/sata_sil24.o*
text data bss dec hex filename
12764 614 2688 16066 3ec2 drivers/ata/sata_sil24.o.new
12320 1058 2688 16066 3ec2 drivers/ata/sata_sil24.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This quirk patch fixes one kind of bug inside some Intel Sandybridge
chipsets, see reports from
https://bugzilla.kernel.org/show_bug.cgi?id=40592.
Many guys also have reported the problem before:
https://bugs.launchpad.net/bugs/737388https://bugs.launchpad.net/bugs/794642https://bugs.launchpad.net/bugs/782389
......
With help from Tejun, the problem is found to be caused by 32bit PIO
mode, so introduce the quirk patch to disable 32bit PIO on SATA piix
for some Sandybridge CPT chipsets.
Seth also tested the patch on all five affected chipsets
(pci device ID: 0x1c00, 0x1c01, 0x1d00, 0x1e00, 0x1e01), and found
the patch does fix the problem.
Tested-by: Heasley, Seth <seth.heasley@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_sff_data_xfer[32]() use pad area if the transfer size isn't
multiple of transfer size; however, this area wasn't cleared and
garbage data in pad area could be transferred to the device. Make
sure the pad area is cleared.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Lei Ming <tom.leiming@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver uses dev_get_drvdata() to get to the driver data for the
platform and PCI devices, while the corresponding wrappers exists for
them -- in one case it even declares an otherwise unneeded variable
to do that. Switch to using the {platform|pci}_get_drvdata() instead.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
mv_platfrom_probe() forgets to call clk_disable() and clk_put() iff
ata_host_activate() fails...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
